Views
1 year ago

CV7300 Instruction Manual - TECO-Westinghouse Motor Company

CV7300 Instruction Manual - TECO-Westinghouse Motor Company

CV7300 Instruction Manual - TECO-Westinghouse Motor

  • Page 2: Quick Start Guide This guide is to
  • Page 6: Table of Content Quick Start Guide
  • Page 10: Chapter 0 Preface Chapter 0 Preface
  • Page 14: 1.1.2 During Power ON Danger Chapte
  • Page 18: Chapter 2 Definition of model Inver
  • Page 22: 3.2 Environmental precautions Do no
  • Page 26: 3-4 Chapter 3 Ambient Environment a
  • Page 30: ※Notice 3-6 Chapter 3 Ambient Env
  • Page 34: Chapter 3 Ambient Environment and I
  • Page 38: Chapter 3 Ambient Environment and I
  • Page 42: 3.4.2 General Specifications Freque
  • Page 46: ※Note 2:-10 ~ 50℃ in distributo
  • Page 50: 3.6 Description of terminals of tro
  • Page 54:

    Symbol Function Description S1 S2 S

  • Page 58:

    (3) Frame3:Three phase JNTHBCBA__BC

  • Page 62:

    3-22 Chapter 3 Ambient Environment

  • Page 66:

    - Frequency Command by 1-06 4-2 Cha

  • Page 70:

    4.1.3 Operation Instruction of the

  • Page 74:

    4.1.5 Keypad Operating Example 4-6

  • Page 78:

    Chapter 4 Software Index 4.2 Contro

  • Page 82:

    0- Drive Operation Mode Function Co

  • Page 86:

    3- Operating Parameters Function Co

  • Page 90:

    5- Multifunction Input Terminals (M

  • Page 94:

    Chapter 4 Software Index 7-05 (AI2

  • Page 98:

    10- Volts/Hz Operation Mode Functio

  • Page 102:

    14- Motor Auto-Tune Parameters Func

  • Page 106:

    4-22 Chapter 4 Software Index Param

  • Page 110:

    command. 4-24 Chapter 4 Software In

  • Page 114:

    4-26 Chapter 4 Software Index Dange

  • Page 118:

    5-00~5-05=06 Jog command Off Off On

  • Page 122:

    Chapter 4 Software Index 3.) 3-20=0

  • Page 126:

    Amplitude Drop = 3-25*amplitude Dev

  • Page 130:

    4-34 Chapter 4 Software Index Param

  • Page 134:

    Chapter 4 Software Index External s

  • Page 138:

    The terminal is provided for the PL

  • Page 142:

    Chapter 4 Software Index running as

  • Page 146:

    Parameter Group 7 - Analog input si

  • Page 150:

    4-44 Chapter 4 Software Index Param

  • Page 154:

    8-02/03= 01: The preset frequency i

  • Page 158:

    Parameter Group 9 - Drive and Load

  • Page 162:

    4-50 Chapter 4 Software Index ※No

  • Page 166:

    10-0 B Chapter 4 Software Index C 0

  • Page 170:

    11-7: Output Lag Filter Time(s) : 0

  • Page 174:

    Chapter 4 Software Index 12-8 Set t

  • Page 178:

    15-1: Software Version 15-2: Fault

  • Page 182:

    4.5 Specification Description on Bu

  • Page 186:

    4.5.3 Application Instructions Coun

  • Page 190:

    (2) Counter Mode 2 ※Note: 4-59 Ch

  • Page 194:

    Sample: Input under the Ladder Prog

  • Page 198:

    (5) Timer Mode 5 (Flash A Mode) (6)

  • Page 202:

    Encoder input Comparing Instruction

  • Page 206:

    @ @ @ Chapter 5 Troubleshooting and

  • Page 210:

    Chapter 5 Troubleshooting and maint

  • Page 214:

    5.1.5 Operation errors Chapter 5 Tr

  • Page 218:

    Is the input power lack of phase? 5

  • Page 222:

    *to previous page Check parameters

  • Page 226:

    Troubleshooting for OV, LV error Th

  • Page 230:

    The motor is overheated Is load or

  • Page 234:

    Any inflation or protrusion ○ Cha

  • Page 238:

    Inverter Model 6.3 Braking unit and

  • Page 242:

    Chapter 6 Peripherals Components LE

  • Page 246:

    Chapter 6 Peripherals Components 00

  • Page 250:

    JNSIF-485 Wiring Diagram: Chapter 6

  • Page 254:

    6.6.4 PDA Link ①. HP iPAQ Pocket

  • Page 258:

    Appendix 2. The motor parameters (1