DSOF-80000 Series - Sloan Valve Company

More documents

Recommendations

Info

LAVATORY SYSTEM ROUGH-IN THREE STATION DSG-83000 Designer <strong>Series</strong> Gradient Triple Station Solid Surface Lavatory System 2 ½” (63 mm) 22” (558 mm) 4” (101 mm) 1 ¹/8” (28 mm) 82” (2082 mm) 90” (2286 mm) DSCT-83000 Designer <strong>Series</strong> Counter Top Triple Station Solid Surface Lavatory System 15” (381 mm) 30” (762 mm) TOOLS REQUIRED FOR INSTALLATION • Electric drill for drilling anchor holes. • Socket or open end wrench for installing anchoring fasteners. • Adhesive Caulk for vanity or bracket mounting • Adhesive for Lavatory optional mounting SINK LOCATION 30” (762 mm) 6 15” (381 mm) 5” (127 mm) 6 ¼” (158 mm) 4” (101 mm) 4” (101 mm) 5” (127 mm) 34” (863 mm) 4” (101 mm) 4” (101 mm) 34” (864 mm) 22” (558 mm) ADA AD • Open end wrench for connecting water lines. • Pipe wrench for installing drain lines. 5” (127 mm) Water Supply ADA 20” (508mm) ADA AD ADA 24” (610 mm) Determine the appropriate wall location for the Lavatory System. Consider that hot and cold water supply lines, a drain line, and an electrical source (receptacle for hardwired faucets) will be required. Compare the physical dimensions of the Lavatory System to the space available for the installation. If wall is not load bearing, a carrier may be required behind the wall. Refer to the appropriate Rough-in diagram on pages 2 – 6 for Lavatory System dimensions. Prior to Lavatory System installation, electric wiring, water supply and drain must be installed. 1– STRAINER INSTALLATION A B Insert Strainer into Basin using plumbers putty (supplied by installer). From beneath Basin, install the Rubber Gasket, Cardboard Seat and Drain Nut onto Strainer. Secure Drain Nut against Basin. RUBBER GASKET CARDBOARD SEAT DRAIN NUT STRAINER 11 ¾” (298 mm)
2A – VANITY MOUNTING A B 2B – WALL MOUNTING A B C D E Note: Wall mounting fasteners supplied by others. Measure and mark a level line on the wall at your required height. 3 - INSTALL FAUCET, SENSOR, DRAIN AND WATER LINE CONNECTIONS A B Apply adhesive caulk (not supplied) to perimeter of vanity casework and corners of deck. With the help of another person, place the lavatory deck on vanity. Measure and mark the Bracket locations as shown. Drill holes in the wall using the Mounting Bracket as a template. Install wall anchors that are specific for that type of wall: drywall, concrete, metal studs, wood studs, etc. (supplied by installer). Some wall materials will require additional reinforcement. Anchors with a minimum pull-out force of 1000 lbs. (reinforce wall at anchor points.) Secure Mounting Brackets (optional) to the wall. Use left and right Brackets as required. Note: Be sure Mounting Bracket is level and plumb against wall so that Lavatory will drain correctly once assembly is completed. Apply adhesive (not supplied) to brackets and corners of lavatory deck. With the help of another person, place the Lavatory on the Mounting Brackets and secure to screws to subtop. Caution: Do not leave lavatory on mounting brackets unsupported. It may fall and cause damage or personal injury. Install faucet, sensor, and water line connections as instructed in the installation instructions furnished with the Faucet. Install P-trap and drain lines making sure that all connections are secure. Note: P-trap and drain lines furnished by others. 7 WALL WATER SUPPLY LINE DRAIN LINE FLEX HOSE MOUNTING BRACKETS C Flush supply line(s) of any debris. Install Flex Hose(s) to water supply line(s). Tighten fitting(s) securely. CARE AND CLEANING DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean lavatory deck or faucets that may dull the luster and attack the finish. Use ONLY soap and water, then wipe dry with clean cloth or towel. While cleaning the sink area, protect the faucet from any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating. STRAINER P-TRAP
Page 1 and 2: Code No. 0816644 Rev. 1 (10/12) INS
Page 3 and 4: LAVATORY SYSTEM ROUGH-IN SINGLE STA
Page 5: LAVATORY SYSTEM ROUGH-IN TWO STATIO
Page 9: PARTS LIST 7 Item Description No. 1

DSOF-80000 Series - Sloan Valve Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?