Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
<strong>690</strong> <strong>LC4»</strong><br />
71<br />
7<strong>65</strong>.01.099.025 / 04<br />
ENDURO<br />
CNC-GABELBRÜCKE<br />
Offset 22,5 oder 25,5 mm.<br />
CNC TRIPLE CLAMP<br />
Offset 22.5 or 25.5 mm.<br />
610.02.055.060<br />
DUKE / SUPERMOTO R<br />
CNC-DECKEL KUPPLUNGSRESERVOIR<br />
CNC-gefräste Ausführung aus hochfestem<br />
Aluminium.<br />
CNC CAP CLUTCH RESERVOIR<br />
CNC machined Version made of high-strength<br />
aluminium.<br />
SXS.05.450.220<br />
SUPERMOTO / ENDURO / SMC<br />
CNC-DECKEL FÜR GEBERZYLINDERKUPPLUNG<br />
CNC-gefräste Ausführung aus hochfestem<br />
Aluminium.<br />
CNC HYDRAULIC CLUTCH COVER<br />
CNC machined Version made of high-strength<br />
aluminium.<br />
7<strong>65</strong>.13.903.000<br />
ENDURO<br />
CNC-HANDBREMSZYLINDERDECKEL<br />
CNC-gefräste Ausführung aus hochfestem Aluminium.<br />
CNC HAND-BRAKE CYLINDER COVER<br />
CNC machined Version made of high-strength<br />
aluminium.<br />
750.01.099.033 / 04<br />
SUPERMOTO / DUKE<br />
CNC-GABELBRÜCKE<br />
CNC-gefräst, Offset einfach einstellbar: 30,5 mm oder 33,5 mm.<br />
Vorderrad und Gabel müssen zur Offsetverstellung nicht demontiert<br />
werden. Inklusive Gabelschaftrohr und Steuerkopflager unten. Bei<br />
33,5 mm Offset ist das Lenkerschloss nicht funktionsfähig. Zur<br />
Montage des Lenkers ist zusätzlich einer der drei unten angeführten<br />
Lenkeraufnahmen notwendig.<br />
CNC TRIPLE CLAMP<br />
CNC machined. Easy adjustable offset 30.5mm or<br />
33.5 mm. Frontwheel and Fork must not be removed for changing<br />
the offset. Set includes pivot tube und lower bearing. At offset<br />
33.5 mm the steering lock is not useable. For mounting of the<br />
handlebar you need one of the three below listed handlebar supports.<br />
7<strong>65</strong>.01.199.035 / 04<br />
SMC<br />
CNC-GABELBRÜCKE<br />
Offset 32,5 oder 35,5 mm.<br />
CNC TRIPLE CLAMP<br />
Offset 32.5 or 35.5 mm.<br />
610.13.009.100<br />
DUKE / <strong>690</strong> SUPERMOTO R<br />
CNC-DECKEL BREMSFLÜSSIGKEITSBEHÄLTER<br />
CNC-gefräste Ausführung aus hochfestem<br />
Aluminium.<br />
CNC CAP BRAKE-FLUID RESERVOIR<br />
CNC machined Version made of high-strength<br />
aluminium.<br />
SXS.08.300.040<br />
SUPERMOTO / DUKE / SMC / ENDURO<br />
CNC-EINSTELLKNOPF-SET<br />
Aus hochfestem Aluminium CNC-gefräst.<br />
CNC KNOB ADJUSTER SET<br />
CNC machined Aluminium.<br />
750.03.045.000<br />
VORNE<br />
FRONT<br />
SUPERMOTO / DUKE / SMC<br />
750.03.046.100<br />
HINTEN<br />
REAR<br />
SUPERMOTO / DUKE / SMC<br />
STURZPAD<br />
Schützt die Gabel / Schwinge vor Beschädigungen<br />
bei einem eventuellen Sturz.<br />
CRASH PADS<br />
Will protect your forks / swingarm in the event<br />
of a crash.<br />
594.01.039.044 37 mm<br />
594.01.039.144 47 mm<br />
LENKERAUFNAHME<br />
In zwei verschiedenen Höhen lieferbar.<br />
HANDLEBAR SUPPORT<br />
Available in two different heights.<br />
595.01.039.244 28 mm<br />
WERKS-LENKERAUFNAHME<br />
3-fach höhenverstellbar,<br />
28 mm, 37 mm, 46 mm.<br />
FACTORY HANDLEBAR SUPPORT<br />
Three possible height adjustments,<br />
28 mm, 37 mm, 46 mm.<br />
SXS.07.125.200<br />
PHDS PROGRESSIVE HANDLEBAR DAMPING SYSTEM<br />
Vorteile:<br />
– Peitschende und harte Schläge werden gedämpft.<br />
– Vibrationen von Chassis und Motor werden<br />
absorbiert.<br />
– Lenker bekommt eine zusätzliche Dämpfung<br />
in horizontaler Richtung.<br />
– Optimale Lenkpräzision.<br />
– Lenkerposition in der Höhe 2-fach verstellbar.<br />
– Schonung der Hand- und Schultergelenke.<br />
– Individuelle Abstimmung durch verschieden<br />
harte Dämpfungselemente möglich.<br />
– CNC-gefräst.<br />
PHDS PROGRESSIVE HANDLEBAR DAMPING SYSTEM<br />
Advantages:<br />
– Headshake and hard hits dampened.<br />
– Vibrations from chassis and engine absorbed.<br />
– Handlebars additionally damped in horizontal<br />
direction.<br />
– Optimal steering precision.<br />
– Handlebar height adjustable in two positions.<br />
– Protects the hand and shoulder joints.<br />
– Individual set-up possible due to the selection of<br />
different damping elements supplied.<br />
– CNC-milled.<br />
<strong>KTM</strong>_Folder_PP_Street_Part2_RZ.inAbs1:70-Abs1:71 Abs1:70-Abs1:71<br />
22.01.2008 11:03:47 Uhr