332 CCS hydra
332 CCS hydra
332 CCS hydra
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
Shark<br />
<strong>332</strong> <strong>CCS</strong> <strong>hydra</strong><br />
SHARK <strong>332</strong> <strong>CCS</strong> HYDRA, Bandsägemaschine<br />
für aufsichtslose einzelne Schnitte von 60° links<br />
bis 45° rechts:<br />
SCHNITTZYKLUS<br />
- Nachdem das Schnittmaterial korrekt positioniert<br />
wurde, ist über die neue Schaltkonsole der Zugriff<br />
auf folgende Funktionen möglich:<br />
- Schließen des Schraubstocks.<br />
- Start des Schnittzyklusses durch die Absenkung<br />
des Sägearms durch Eigengewicht und Regulierung<br />
der Schnittgeschwindigkeit durch einen<br />
<strong>hydra</strong>ulischen Bremszylinder.<br />
Wenn der Schnitt ausgeführt ist, hebt der<br />
Maschinenwärter den Sägearm über die<br />
Schaltkonsole und ein <strong>hydra</strong>ulisches Steuergerät<br />
soweit erforderlich und öffnet den pneumatischen<br />
Schraubstock für die Zuführung des Materials.<br />
EINIGE MERKMALE:<br />
- Elektrische Anlage (voll identifizierbare elektrische<br />
Verkabelung, Stand-By, abschließbarer<br />
Hauptschalter mit Türverriegelung, Motorschalter,<br />
Not-Aus-Vorrichtung, Motorschutzschalter mit<br />
thermomagnetischem Auslöser,<br />
Unterspannungsauslöser, Phasenausfallschutz,<br />
Niederspannungsanlage 24 Volt).<br />
- Drehtisch (auf Rollenlager von 420 mm mit<br />
vorgespanntem Drucklager montiert) mit<br />
auswechselbarem Arbeitstisch aus Stahl.<br />
26<br />
network
0 0<br />
1<br />
Ø 24<br />
3<br />
Ø 22,5<br />
15<br />
START<br />
m/min<br />
90<br />
Kg<br />
Ø 24<br />
STOP<br />
3<br />
Ø 22,5<br />
0<br />
F<br />
- Doppelte Drehzahl des Bandes (36/72 m/min)<br />
(OPTIONAL 20/40 m/min)<br />
- Elektronischer Umwandler der<br />
Sägebandspannung mit Anzeige an der<br />
Schaltkonsole.<br />
- Pneumatischer Schraubstock mit<br />
Schnellverstellung.<br />
- Untergestell mit Kühlmittelwanne und<br />
Späneschublade, die durch einen motorisierten<br />
Späneförderer (Zubehör) ersetzt werden kann.<br />
- Elektrische Kühlmittelpumpe zur Kühlung und<br />
Schmierung des Sägebandes.<br />
- Vorbereitung für den Einbau der<br />
Minimalmengenschmierung des Sägebands<br />
(OPTIONAL), nebst der herkömmlichen<br />
serienmäßigen Schmierung mit Emulsionsöl.<br />
- Späneräumbürste.<br />
- Einstellbare Präzisionsanschläge mit<br />
Millimeterskala und klappbarem Anschlag, um<br />
Schnitte gleicher Länge auszuführen.<br />
- Maschine ist für den Hubwagentransport<br />
geeignet.<br />
- Bimetall-Sägeband für Voll- und Profilmaterial.<br />
- Werkzeug, Gebrauchsanweisung und<br />
Explosionszeichnungen für Ersatzteile.<br />
SHARK <strong>332</strong> <strong>CCS</strong> HYDRA, band sawing machine<br />
for single cuts without operator from 60° on<br />
the left to 45°.<br />
CUTTING CYCLE<br />
- After positioning the bar, operate through the<br />
new console to access the following controls:<br />
- vice closing<br />
- starting the cutting cycle that uses the weight<br />
of the head controlled by a <strong>hydra</strong>ulic braking<br />
circuit to adjust the feeding speed.<br />
After the cut, by the keyboard controls, the<br />
operator lifts the head through a <strong>hydra</strong>ulic control<br />
unit till the necessary position and opens again<br />
the pneumatic vice to enable a new bar feeding.<br />
A FEW FEATURES:<br />
- Electrical system (entirely identifiable wiring,<br />
stand-by, main switch with lock, motor switch,<br />
emergency device, motor overload cutout, min.<br />
voltage coil, phase shortage protection, low<br />
voltage system 24 V).<br />
- Rotating table (installed on a roller bearing,<br />
diameter 420 mm, pre-loaded with thrust<br />
bearing) complete with replaceable steel plates<br />
on the working surface.<br />
- Double band rotation speed 36/72 m/min<br />
(OPTIONAL 20/40 m/min)<br />
- Electronic transducer for the band tensioning<br />
with displaying on the console.<br />
- Pneumatic vice with fast approach device.<br />
- Stand with coolant tank and chip tray that can<br />
be replaced with a motor-driven chip extractor<br />
(OPTIONAL).<br />
- Electric pump for the band lubrication and<br />
cooling.<br />
- Machine preset to be equipped with the blade<br />
minimal lubrication kit (OPTIONAL), as well as<br />
with the standard-delivered traditional lubrication<br />
with emulsifiable oils.<br />
- Brush band-cleaning device.<br />
- Adjustable rod to measure stop to make cuts<br />
of the same length with millimetred steel rod.<br />
- Machine preset for being handled by transpallet.<br />
- Bimetallic band for profiles and solid pieces.<br />
- Service keys and instructions manual, for<br />
maintenance and spare parts list.<br />
3<br />
<strong>332</strong><strong>hydra</strong><br />
0<br />
1 2<br />
27<br />
0° 300 260 330x260<br />
45° 260 250 270x200<br />
mm kw m/min mm 60° 180 170 170x170<br />
<strong>332</strong>0x27x0,9 1,5/1,8 40/80 335 45° 200 180 200x160<br />
Zubehöre Seite - Optionals from page 74<br />
n. 02,03,04,12,13,18,70,92<br />
kg<br />
670<br />
1300<br />
2000<br />
SH <strong>332</strong><br />
HYDRA<br />
2000<br />
2000<br />
1260<br />
1<br />
2<br />
1<br />
2<br />
network