12.07.2015 Aufrufe

Abformungstechnik mit elastischen Kunststoffen Moulding ...

Abformungstechnik mit elastischen Kunststoffen Moulding ...

Abformungstechnik mit elastischen Kunststoffen Moulding ...

MEHR ANZEIGEN
WENIGER ANZEIGEN
  • Keine Tags gefunden...

Erfolgreiche ePaper selbst erstellen

Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.

5 6Zweite Si-Spachtelung, weißSecond Si Paste application, white, without pigmentDeuxième couche d’estampage (non colorée)Fixierungsstreifen in die zweite Spachtelung einbetten und anformenEmbed and adjust fixing strip in second trowellingMise en place des profils de positionnementSeifenlösung verhindert ein Anhaften underleichtert diesen Arbeitsschritt.RECKLI-SI-Abformpaste HR-Nstreich- und spachtelbarer Zweikompo nen -ten-Silikonkautschuk, raumtemperaturvernetzendVerbrauch: ca. 1,1 kg/m 2 je mm Schicht -stärkeIm Doppelgebinde ferner enthalten:RECKLI-SI-Verdicker flüssig KThixotropier<strong>mit</strong>telDosierung: 0,1 - 1,5 %RECKLI-SI-Farbpastegrün, Dosierung ≤ 1 %Auch vor dem Auftragen der ab schließen -den dritten Schicht ist darauf zu achten,dass der vorherige Silikonauftrag soweitdurchgehärtet ist, dass ein Verschiebendurch die weitere Spachtelung nicht mehrmöglich ist. (Bild 5)Um der <strong>elastischen</strong> Silikonform später inder starren Stützform einen guten Sitz undeine optimale Fixierung zu geben, werden inden letzten frischen Spachtelauftrag imRandbereich oder in der Fläche Profil -schnüre, Streifen oder Noppen aus Silikoneingebettet und angearbeitet, die zuvorseparat angefertigt wurden. (Bild 6)Diese Profilierungen vermeiden gleichzeitigauch ein Verrutschen der <strong>elastischen</strong> Formin der Stützform während des Füllvor -ganges für die Reproduktion des Originals.Achtung! Direkter Kontakt unterschiedlicherSilikonelastomere kann, bedingt durchWeichmacherwanderung, zu Verformungenoder verstärktem Ausbluten der Silikonformführen. Achten Sie in jedem Fall darauf,dass weder innerhalb ein und derselben4RECKLI SI Mould Paste HR-Ntwo component silicone rubber, applicationby brush or by trowel, room temperaturecuring.Consumption: approx. 1,1 kg/sqm per mmlayer thickness.Also included in the drum:RECKLI SI Thickener Liquid KThixotropic agentDosage: 0,1 – 1,5 %RECKLI SI Colour Pastegreen, Dosage ≤ 1 %As before this layer must also have set sufficientlyso that it can not be displaced bythe final third coat (picture 5).In order to give the elastic silicone mould agood fit and optimal fixing qualities later inthe solidified supporting mould, profilecords, strips or burls of RECKLI SI MouldPaste HR-N, made separately before-hand,are bedded and worked into the border orthe surface of the final fresh coat of siliconerubber (picture 6).At the same time these profiles also preventthe elastic mould from slipping in the supportingmould during the casting process ofthe reproduction of the original.Attention! Direct contact of silicone rubbersof a different kind may lead to deformationor bleeding of the silicone mouldcaused by migration of plasticizer. Pleaseobserve in any case, that silicon rubber ofdifferent types must not let come into directcontact with oneanother, neither within onemould nor during storing moulds later on.With this final application care must betaken to level undercuts, burls and edges insuch a way that there are no constrictivepositions when the supporting mould isPâte d’estampage RECKLI SI HR-NCaoutchouc silicone à deux composantsapplicable au pinceau ou à la spatule, réticulationà température ambianteUtilisation: env. 1,1 kg/m 2par mm d’épaisseurde coucheÉgalement compris dans le pot :Additif thixotropant RECKLI type KAgent thixotropantDosage 0,1 - 1,5 %Pâte colorante RECKLI SIde couleur verte, dosage ≤ 1 %Même avant l’application de la troisième etdernière couche, il convient de vérifier quela couche de silicone précédente est durcieet empêche tout déplacement dû à unenouvelle enduction. (Illustration 5).Afin de garantir ultérieurement au moule desilicone élastique une bonne tenue et unefixation optimale dans l’ossature solidifiée,des cordes de profil ou des bandes en siliconepréformés seront plaqués à la périphériedu moulage encore pâteux.(Illustration 6)Ces profils éviteront également tout déplacementdu moule dans son support lors ducoulage des épreuves.Attention! Le con tact direct de différentsélastomères de silicone, peut selon lamigration de plastifiant, entraîner des déformationsou des étalements du moule desilicone. Vérifiez impérativement que, dansun seul et même moule ou bien lors dustockage ultérieur, les différents types decaoutchouc de silicone n’entrent pas encontact direct!Pour la dernière enduction, il importe detraiter les détails, arêtes et bords de façonà ce qu’aucun point de contrainte n’appa-

Hurra! Ihre Datei wurde hochgeladen und ist bereit für die Veröffentlichung.

Erfolgreich gespeichert!

Leider ist etwas schief gelaufen!