FLEX I/O EtherNet/IP Adapter Module User Manual, 1794-UM006A ...

More documents

Recommendations

Info

3-6 Configuring the 1794-AENT Adapter for Your EtherNet/IP Network Using the Rockwell BootP Utility Publication 1794-UM006A-EN-P - July 2001 The Rockwell BootP utility is a stand alone program that incorporates the functionality of standard BootP software with a user friendly graphical interface. It is located in the Utils directory on the RSLogix 5000 installation CD. The 1794-AENT adapter must have BootP enabled (factory default) to use the utility. To configure your adapter using the BootP utility, perform the following steps: 1. Run the BootP software. In the BOOTP Request History panel you will see the hardware addresses of devices issuing BootP requests. 2. Double-click on the hardware address of the device you want to configure. You will see the New Entry pop-up window with the device’s Ethernet Address (MAC). 3. Enter the IP Address, Subnet Mask, and Gateway you want to assign to the device, and click on OK.
Configuring the 1794-AENT Adapter for Your EtherNet/IP Network 3-7 The device will be added to the Relation List, displaying the Ethernet Address (MAC) and corresponding IP Address, Subnet Mask, and Gateway (if applicable). 4. If you want to permanently assign this configuration to the device, highlight the device and click on the Disable BOOTP button. When power is recycled to the device, it will use the configuration you assigned and not issue a BootP request. Note: To enable BootP for a device that has had BootP disabled, highlight the device and click on the Enable BOOTP button. Publication 1794-UM006A-EN-P - July 2001
Page 1 and 2: FLEX I/O EtherNet/IP Adapter Module
Page 3 and 4: Throughout this manual we use these
Page 5: Rockwell Automation Support Rockwel
Page 8 and 9: P-2 About This User Manual How To U
Page 10 and 11: P-4 About This User Manual Where to
Page 12 and 13: P-6 About This User Manual Publicat
Page 14 and 15: P-8 About This User Manual Publicat
Page 16 and 17: Table of Contents ii Using Analog I
Page 18 and 19: 1-2 About the 1794-AENT Adapter Har
Page 20 and 21: 1-4 About the 1794-AENT Adapter Sup
Page 22 and 23: 1-6 About the 1794-AENT Adapter Pub
Page 24 and 25: 2-2 Installing the 1794-AENT Adapte
Page 30 and 31: 3-2 Configuring the 1794-AENT Adapt
Page 38 and 39: 3-10 Configuring the 1794-AENT Adap
Page 44 and 45: 4-2 Using Rack Optimized Discrete I
Page 52 and 53: 4-10 Using Rack Optimized Discrete
Page 60 and 61: 5-2 Using Analog I/O with Direct Co
Page 68 and 69: 5-10 Using Analog I/O with Direct C
Page 74 and 75: A-2 LED Status Indicators Publicati
Page 76 and 77: B-2 1794-AENT Adapter Web Pages Pub
Page 82 and 83: C-2 Configuring the RSLinx Ethernet
Page 84 and 85:
C-4 Configuring the RSLinx Ethernet
Page 86 and 87:
2 Index N network status indicator
Page 88:
Other Comments PLEASE FOLD HERE BUS
show all

FLEX I/O EtherNet/IP Adapter Module User Manual, 1794-UM006A ...

Create successful ePaper yourself

Delete template?

Save as template?