Batten luminaires - Alfred Pracht Lichttechnik GmbH

Batten luminaires
01with
reflectors
Protection Class II according to VDE 0711/EN 60598
Ingress protection IP65
Dust-proof
Jet-proof
230V/50 Hz
48
Listed with the
Deutsche Bahn AG
10
Batten luminaire
System Apollo T8
for FL T8/26 mm
single- and twin-lamp
with threaded ring lampholders
Housing: Slim, elegant, fully sealed luminaire housing made of white,
fibreglass-reinforced polyester, essentially fully resistant against acids and alkalis.
Socket end pieces: One-piece socket ends made of PBTP.
Socket: Two-slot plug-in socket with silver-plated contacts.
Lamp cover: Batten luminaire, can be supplemented with accessories.
Seals: Short, age-resistant silicone seals.
Electrical components: Low loss ballast B1 starter; electronic ballast;
through-wiring max. 7 x 2.5 mm 2 .
Installation: Variable mounting points with Pracht Clip System made of
stainless steel. Suitable for ceiling, pendant and horizontal wall mounting.
Befestigungslochabstand
variabel
* Variable mounting points
131±2
Protective tube, internal ribbing; cable entry at the side resp. ceiling side. Connection compartment for continuous mounting and vertical lamp insertion.
58
±1
58
±1
L 216±2
Type (VDE designation) Watt Inductive Compensated Electronic ballast L Weight
Art.-No. Art.-No. Art.-No. (mm) (kg)
Luminaire for individual and continuous mounting, two connection covers and through-wiring 2 x 1.5 mm 2
PPR SR 212/1 1 x 18 165 100 165 101 165 103 632±2 1.6
PPR SR 212/3 1 x 36 165 230 165 231 165 233 1242±2 2.1
PPR SR 212/5 1 x 58 165 360 165 361 165 363 1542±2 3.4
PPR SR 212/2 2 x 18 165 130 165 131 165 133 632±2 2.5
PPR SR 212/4 2 x 36 165 260 165 261 165 263 1242±2 3.6
PPR SR 212/6 2 x 58 165 400 165 401 165 403 1542±2 4.6
Luminaire for continuous mounting, two connection covers and through-wiring 4 x 1.5 mm 2
PPR SR 214/1 1 x 18 170 100 170 101 170 103 632±2 1.6
PPR SR 214/3 1 x 36 170 230 170 231 170 233 1242±2 2.1
PPR SR 214/5 1 x 58 170 360 170 361 170 363 1542±2 3.4
PPR SR 214/2 2 x 18 170 130 170 131 170 133 632±2 2.5
PPR SR 214/4 2 x 36 170 260 170 261 170 263 1242±2 3.6
PPR SR 214/6 2 x 58 170 400 170 401 170 403 1542±2 4.6
Extra cost:
El. bal. Dim 1–10V (add to electronic ballast version) 685 004
El. bal. Dim Dali (add to electronic ballast version) 685 005
El. bal. Industry (add to electronic ballast version) 36/58 685 006
Non-silicone design 685 009
Cable entry at the side 691 150
Cable entry at the ceiling side 691 151
Conductor cross-section 1.5 mm 2 = 10 A
Conductor cross-section 2.5 mm 2 = 16 A
Extra cost for version with 4 x 1.5 mm 2 :
Built-in through-wiring, 4 x 2.5 mm 2 18 Watt 690 124
36 Watt 690 324
58 Watt 690 524
Note: For accessories, see page 50!
*For versions with electronic ballast:
Identification
Luminaires must be operated
with covers in place!
Areas of application: Car parks, damp and humid rooms, auxiliary rooms, industrial plants, automotive industry, continuous mounting applications.
91±2