Intelligent Tally System WIT - 100 Series WIT

WIT - 100 Series
WIT-100C Intelligent Tally Controller Rear View
WIT-164TI 64CH Tally Data Converter Rear View
Intelligent Tally System
WIT - 100 Series
본 장비는 원활한 방송 진행을 위하여 조정실에 Video Monitor와 함께 설치되는 Tally Display System 으로 Routing Switcher 및 Video Switcher와
연동되어 각 영상신호의 이름이 변경 되어지며 사용 상태를 녹색, 오렌지색 또는 적색으로 표시하기 위한 장비이다.
Features
UMD(Under Monitor Display) tally lamp controller with
management software
Easily change for display characters
(Korean, English, Chinese, Japanese, etc)
Select 16×16 LED dot or 5×7 LED dot matrix device
Maximum 128 displays per system (Option 255 display)
RJ-45 connector (Data) for Display
Adjust brightness of each color
Dual power supply (WIT-100C)
Technical Specification
WIT-100C Intelligent Tally controller
1) WIT-100C (Frame)
Main Module Slot 1EA
Sub Module Slot 4EA
Power Module Slot 2EA
Front Config Port RS-232 1EA
Front Power Switch &
Dual Color LED 2Set
Dimensions 483(W)×88(H)×350(D)mm
2) WIT-100CP (Power Supply Module)
Dual Power 2EA / Frame
AC Power 85V ~ 264V 50/60HZ(Free Voltage)
3) WIT-100CM (Main Module)
Display Output Port 4EA of RS-422/TX, RJ-45
Configuration Port 2EA of RS-232, (Dsub-9)
Firmware Debug Port 1EA of ICSP
4) WIT-100CD (Data Input Module, Option)
Communication Port 2EA of RS-422, (Dsub-9)
Firmware Debug Port 1EA of ICSP
5) WIT-100CG (GPIO Module, Option)
Tally Data Channel 16CH In & Out
Tally Data Input Type Active Low (GND), Voltage Control
Tally Data Output Type Isolated Open Collector
6) WIT-100CT (SMPTE Time Module, Option)
Balance Input Connector 1EA of Phoenix Type (3P)
Unbalance Input Connector 1EA of BNC Type (75ohm)
Time Code Type SMPTE/EBU Serial Time Code
WIT-100CM
WIT-100CD WIT-100CG WIT-100CT
Ordering Information
WIT-100C Intelligent Tally Controller
Option Modules Data Input Module
GPIO Module
SMPTE Time Module
WIT-164TI 64CH Tally Data Converter
WIT-162TS Emergency Tally Switcher
WIT-101G GPI I/O Interface
7) Management Software
System Configuration
UMD Text Configuration
Setup Tally Data Input or Output
Setup Routing Switcher Interface & Text Data
Windows XP
Management Software
WIT-164TI 64CH Tally Data Converter
1) Tally Input
Channel 16CH×4
Device Photocoupler
2) Secondary Tally Input
Channel 8CH×2
Device Photocoupler
Assign CH1 ~8, CH33 ~ 40
3) Tally Output
Channel 16CH×4
Assign Primary Input
Device Photocoupler
Type Isolated Open Collector
4) Data output
Assign [Primary or Secondary] Input
Port 1 Port, RS-422, (Dsub-9)
5) General
Operating Temp. 0
Note : Specifications are subject to change without notice
oC ~ 40oC Power Free voltage(AC 85~264V) 50/60HZ
Dimensions 483(W)×88(H)×350(D)mm

16X16 Dot UMD
WIT-115D Under Monitor Display Rear View
WIT-115R Under Monitor Display (19" Type)
Rear View
WIT-125R Under Monitor Display (19" Dual Type)
Rear View
5X7 Dot UMD(Text H=32mm)
WIT-118D Under Monitor Display Rear View
WIT-118R Under Monitor Display (19" Type)
Rear View
WIT-128R Under Monitor Display (19" Dual Type)
Rear View
5X7 Dot UMD(Text H=20mm)
WIT-118DS Under Monitor Display Rear View
WIT-118RS Under Monitor Display (19" Type)
Rear View
WIT-128RS Under Monitor Display (19" Dual Type)
Rear View
Intelligent Tally System
Under Monitor Display / WIT - 100 Series
Features
Intelligent Tally Display
16×16 Dot Matrix & (Korea 5 Digit, English 10 Digit)
Display Text : Numeric, English, Korean, etc. (by Windows)
최대 127개의 ID
Data Input (RS-422) with Through Output
GPI Tally Input
3 Color Display Control(Green : Standby, Orange : PVW Tally On, Red : PGM Tally On)
Data Fault Display
Technical Specification
Data Input RS-422, with Through Output (RJ-45 Connector)
Tally Input
Assign PGM&PVW
Type GPI / Low Active
Display
Device 16×16 LED Dot Matrix (Korea 5 Digit, English 10 Digit)
Text by Windows Language
Color Standby(Green), PVW(Orange), PGM(Red)
Brightness Adjust Red & Green
General
Power Free Voltage(AC 85~264V) 50/60Hz
Dimensionns 241(W)×44(H)×120(D)mm / 483(W)×44(H)×120(D)mm
Features
Intelligent Tally Display
5×7 Dot Matrix
Display Text : Numeric, English(by Windows)
최대 127개의 ID
Data Input (RS-422) with Through Output
GPI Tally Input
3 Color Display Control(Green : Standby, Orange : PVW Tally On, Red : PGM Tally On)
Data Fault Display
Technical Specification
Data Input RS-422, with Through Output (RJ-45 Connector)
Tally Input
Assign PGM
Type Low Active or High Active
Display
Device 5×7 LED Dot Matrix, LED H=32mm
Text Numeric, English 8 Digit, (by Windows)
Color Standby(Green), PVW(Orange), PGM(Red)
Brightness Adjust Red & Green
General
Power Free Voltage(AC 85~264V) 50/60Hz
Dimensionns 241(W)×44(H)×120(D)mm / 483(W)×44(H)×120(D)mm
Features
Intelligent Tally Display
5×7 Dot Matrix
Display Text : Numeric, English(by Windows)
최대 127개의 ID
Data Input (RS-422) with Through Output
GPI Tally Input
3 Color Display Control(Green : Standby, Orange : PVW Tally On, Red : PGM Tally On)
Data Fault Display
Technical Specification
Data Input RS-422, with Through Output (RJ-45 Connector)
Tally Input
Assign PGM
Type Low Active or High Active
Display
Device 5×7 LED Dot Matrix, LED H=20mm
Text Numeric, English 8 Digit, (by Windows)
Color Standby(Green), PVW(Orange), PGM(Red)
Brightness Adjust Red & Green
General
Power Free Voltage(AC 85~264V) 50/60Hz
Dimensionns 241(W)×44(H)×120(D)mm / 483(W)×44(H)×120(D)mm

WIT - 101G
WIT-101G GPI I/O Interface Rear View
Intelligent Tally System
WIT - 100 Series
본 장비는 Video Switcher의 동일한 Tally 출력을 여러 곳의 Machine Control 신호로 사용하기 위한 Tally 신호의 분배장비이다. Tally 입력은 UMD와 같은
RS-422 신호를 사용하므로 원거리 설치 시에도 배선 작업이 용이하다.
Features
Data to GPO Tally Converter
32CH+32CH GPO
Data Distributor for Display (2Port)
Individual ID 1 & ID 2 for Tally Assign
Dual Power Supply
WIT - 162TS
Technical Specification
Tally Input RS-422, With Through Output (RJ-45)
Tally Output
Channel 32CH(ID1)+ 32CH(ID2)
Type Isolated Open Collector (Photo-Coupler)
Power Free Voltage(AC 85~264V) 5016Hz
Dimensionns 483(W)×44(H)×350(D)mm
WIT-162TS Emergency Tally Switcher Rear View
본 장비는 제작되는 프로그램의 종류(상황)에 따른 Tally 신호의 절체가 필요한 경우 사용하는 Tally Switcher로서 4개의 16CH Tally 입력과 2개의 16CH Tally
출력을 가진다. (4×2 Switcher)
Features
4×2 Tally Switcher (16CH)
Individual Output A & Output B
Distributed Output (16+16+, 16+16)
16CH Mode & 32CH Mode
Dual Power Supply
Application 1 : VMU(GPO/64CH) Only
Application 2 : VMU(GPO/32CH) Only
Technical Specification
Tally Input
Channel 16CH×4
Divide Photo-Coupler
Tally Output
Channel 16CH×2
Type Isolated Open Collector (Photo-Coupler)
Operating Mode
Select Internal Jumper ON/OFF
16CH Mode 4×2 Switcher (1, 2, 3, 4 → A or B)
32CH Mode 2×1 Switcher (1, 2 → A & 3, 4 → B)
Power Free Voltage
Dimensionns 483(W)×44(H)×350(D)mm

Application 3 : VMU(RS-422) Only
Application 4 : VMU(GPO/64CH) + R/S(RS-422)
Application 5 : VMU(GPO/32CH) + R/S(RS-422)
Application 6 : VMU(RS-422) + R/S(RS-422)
Intelligent Tally System
WIT - 100 Series