INSTRUCTION BOOK - Janome

More documents

Recommendations

Info

Problems and Warning Signs Audible signal Pip Pip-pip-pip Pip-pip-peep Peep Warning sign The buzzer sounds when: Normal operation Invalid operation Buttonhole sewing completed Malfunction Cause Try this The machine will not sew with the start/stop button because the foot control is connected. A buttonhole is sewn without lowering the buttonhole lever. 44 Disconnect the foot control and start the machine. Lower the buttonhole lever and restart the machine. The bobbin winder spindle is moved to the right. Move the bobbin winder spindle to the left. The machine is restarted too soon after it has halted due to the overload. Auto thread cutting error due to a problem in the electronic components or tangled in hook area. Wait for at least 15 seconds to restart. If threads are jamming, remove the jammed threads. Remove the jammed threads in the hook area. If the error occurs again after cleaning the hook area, contact the service center or the store from where the machine was purchased.
Troubleshooting Condition The needle thread breaks. The bobbin thread breaks. The needle breaks. Skipped stitches Seam puckering The cloth is not feeding smoothly. Stitches form loops below the works. The machine does not work. Buttonhole sewing is not sewn properly. The machine does not run smoothly and is noisy. Cause 1. The needle thread is not threaded properly. 2. The needle thread tension is too tight. 3. The needle is bent or blunt. 4. The needle is incorrectly inserted. 5. The needle thread and the bobbin thread are not set under the presser foot when start sewing. 6. The threads were not drawn to the rear after sewing. 7. The thread is either too heavy or too fine for the needle. 1. The bobbin thread is not threaded properly in the bobbin holder. 2. Lint has collected in the bobbin holder. 3. The bobbin is damaged and doesn’t turn smoothly. 4. The thread is wound loosely on a bobbin. 1. The needle is incorrectly inserted. 2. The needle clamp screw is loose. 3. The threads were not drawn to the rear after sewing. 4. The needle is too fine for the fabric being used. 5. The presser foot is not appropriate for the stitch pattern being sewn. 1. The needle is incorrectly inserted, bent or blunt. 2. The needle and/or threads are not suitable for the work being sewn. 3. A Blue Tipped needle is not being used for sewing stretch, very fine fabrics and synthetics. 4. The needle thread is not threaded properly. 5. A poor quality needle is used. 1. The needle thread tension is too tight. 2. The needle thread is not threaded properly. 3. The needle is too heavy for the fabric being sewn. 4. The stitch length is too long for the fabric. 1. The feed dog is packed with lint. 2. The stitches are too fine. 3. The feed dog is not raised after “drop feed” sewing. 1. The needle thread tension is too loose. 2. The needle is either too heavy or too fine for the thread. 1. The machine is not plugged in. 2. Thread has been caught in the hook race. 3. The bobbin winder spindle is not returned to the left after bobbin winding. 1. The stitch density is not suitable for the fabric being sewn. 2. Suitable interface material has not been used for the stretch or synthetic fabric. 1. Thread has been caught in the hook race. 2. Lint has built up in the hook race or bobbin holder. 45 Reference See page 13, 14 See page 17, 18 See page 9 See page 9 See page 19 See page 19 See page 9 See page 12 See page 43 Replace the bobbin. See page 11 See page 9 See page 9 See page 19 See page 9 Change the presser foot. See page 9 See page 9 See page 9 See page 13, 14 Change the needle. See page 17, 18 See page 13 See page 9 Make the stitches shorter. See page 43 Make the stitches longer. See page 9 See page 17, 18 See page 9 See page 4 See page 43 See page 11 See page 29 Use an interfacing. See page 43 See page 43
Page 1 and 2: INSTRUCTION BOOK
Page 3 and 4: SECTION I. NAMES OF PARTS Names of
Page 5 and 6: q w e r t y u i o !0 !1 !2 !3 !4 !5
Page 7 and 8: 5 Speed Control Slider Sewing speed
Page 9 and 10: t y u o i 7 t Thread Cutter Button
Page 11 and 12: z x Light Medium Heavy q w c Fabric
Page 13 and 14: x x c c v b n m z q 11 • Winding
Page 15 and 16: c v b z x c v b z x w e w 13 Thread
Page 17 and 18: z x c q 15 Drawing up the Bobbin Th
Page 19 and 20: q q w w r r q w e e r e t t 17 Adju
Page 21 and 22: q w e q q w e q w w 19 SECTION III.
Page 23 and 24: q w e q w e q w e q w e r r 21 Stra
Page 25 and 26: q w e y q w w e t r u 23 Zigzag Sti
Page 27 and 28: q w e q w e 25 Overedge Stitch q St
Page 29 and 30: z x c v q w e t e q r y u !1 w r u
Page 31 and 32: q w e q w e q w e q w e 29 Adjustin
Page 33 and 34: z x c q w e q e r w 31 Corded Butto
Page 35 and 36: q w e w t q w e e q w e r r q 33 Ta
Page 37 and 38: x c v b n m i !1 o !0 !2 35 Zipper
Page 39 and 40: q w e r z x c v b n 37 Button Sewin
Page 41 and 42: q z q w e q w e x c w w w w q 39 Sm
Page 43 and 44: q w e q w e 41 Cross Stitch q Stitc
Page 45: z x c v b c u q w t y i y r z x r q

INSTRUCTION BOOK - Janome

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?