ThermoIn - ThermoShield

Technical Data Sheet
Technical Data Sheet
ThermoIn
Stucco finish plaster
Granularity: 0-0.5 mm
Olomouc, Horní náměstí
14/17, 779 00
Company ID: 27818624
Tax ID: CZ 27818624
www.izolace-sanace.cz
www.satsys.cz
E-mail: satsyscz@gmail.com
Tel./Fax: +420 585 242 262
Mobile: +420 603 552 211
Description: ThermoIn stucco plaster is a readymade dry mortar mixture. After
mixing with water, it produces a highly pliable mixture with a
granularity up to 0.5 mm. The mixture is suitable for surface
finishing of plasters such as ThermoUM, ThermoSAN and
ThermoUMXtra, and other types of rehabilitation and thermal
insulation plasters. Thanks to its exceptional properties (excellent
openness to diffusion), it guarantees preservation of properties of
the underlying rehabilitation plasters, thus trouble-free functioning
of the overall plaster system. It can be manufactured with a
granularity up to 1.0 mm for protected heritage buildings.
Scope of
application:
Material
consumption:
Surface
preparation:
Use for facade and interior plastering on all types of underlying
surfaces. Particularly suitable for restoration of old, heritage
buildings. For plastering on pumice, gypsum-plaster materials with
plain or complex surfaces.
Approx. 1 kg per m 2 for a thickness of 2 mm; 8 kg pack for 8 m 2
ThermoIn plaster mixture is applied to dry and clean walls, rid of all
impurities and dust; any unevenness on the wall has to be
smoothed.
Working: Mix the full bag content (8 kg) with water to form a homogeneous
blend; the proportion is 8 kg of the material per 3.5-3.9 litres of
water. Stir for 5-7 minutes using a blender. Always mix the full pack
content at once. The mortar produced has to be applied to a surface
within 1 hour of preparation. The mortar is applied manually, like
ordinary mortar, using a steel smoother. Prepare the surface and
remove unevenness before plastering. Paint can be applied after 48
hours.
Technical
specifications:
Water consumption: approx. 3.5-3.9 l
per bag
Compressive strength: approx. 2
N/mm 2
Capillary absorption W1: 0.208
Adhesion: 0.35 N/mm 2
Thermal conductivity λR:
approx. 0.095 W/mK
Fire response class: A1
Vapour diffusion μ: 10
SATSYS Technology a.s. incorporated with the Commercial Registry maintained by
Ostrava Regional Court, Section B, File 3353

Technical Data Sheet
kg/m 2 h 0.5
Bulk density: 440 kg/m3 ± 5%
Storage: Store in a dry place, protect from moisture. Under these conditions,
the storage durability is 12 months from the date of manufacturing
as identified on the pack.
Packaging: The plaster mixtures are supplied in 7 kg paper bags with PE lining.
Each pallet comes with 72 (84) bags and is covered with PE sheet.
Important
instructions:
Safety
instructions:
Safety and
hygiene
standards:
Do not work at too high or too low air and wall temperatures (below
+5°C), in direct sunlight and in strong wind. Do not mix with other
products.
The product is not classified as a hazardous chemical pursuant to
Act no. 157/1998 Coll., as amended by Act no. 352/1999 Coll. The
product may irritate skin, eyes, and mucous membranes. Use
personal protective equipment (work clothes, footwear, gloves,
goggles) when working. If eyes are affected, rinse them wide-open
with water; wash skin with running water. In the case of medical
complaints, seek professional medical assistance.
Warning code: Xi irritating
R 37/38: Irritating to respiratory system and skin
R 41: Risk of serious damage to eyes
R 43: May cause sensitisation by skin contact
S 2: Keep out of reach of children
S 22: Do not breathe dust
S 24: Avoid contact with the skin
S 25: Avoid contact with eyes
S 26: In case of contact with eyes, rinse immediately with
plenty of water and seek medical advice
S 36/37/39: Wear suitable protective clothing, gloves and eye/face
protection
S 46: If swallowed, seek medical advice immediately and show
the container or label
Quality control: We perform continuous quality control on all our products based on
an approved PCS and implement a certified quality management
system under ČSN EN ISO 9001:2009
Manufacturer: SATSYS Technology a.s., Horní náměstí 14/17, 779 00 Olomouc,
ČR
Version: 07.2011
SATSYS Technology a.s. incorporated with the Commercial Registry maintained by
Ostrava Regional Court, Section B, File 3353