Ramsey MINI CK101 Weight Integrator - Hoferick Engineering GmbH

More documents

Recommendations

Info

3.3.2 Dynamic Values Batch Counter The number of the currently running load out or the number of the last finished one. The integrator automatically increments the batch number when a new batch is started. Batch_Set The set point for the current or the next load out. Usually entered or downloaded by the user. For reading operations, the Batch_set value is updated only when a batch is started. Rate The instantaneous rate in engineering units as currently displayed on the RUN screen. Belt Load The instantaneous linear weight in engineering units. Belt Load The instantaneous belt speed in engineering units. Master Total The current value of the master Totalizer of the integrator. Operator Total The current value of the operator Totalizer of the integrator. Operator total can be zeroed by writing zero to this register. Reset Total The current value of the reset Totalizer of the integrator. Reset total can be zeroed by writing zero to this register. Batch Total The current contents of the load out totalizer. Usually read at end of batch to check the result of the load out. This register is automatically cleared when a new batch is started Master Total The current value of the master Totalizer of the integrator, in double format Operator Total The current value of the Operator Totalizer of the integrator, in double format Reset Total The current value of the Reset Totalizer of the integrator, in double format Batch Total The current value of the Batch Totalizer of the integrator, in double format Manual Zero The value in engineering units of the “Zero” constant of the scale. Manual Span The value in engineering units of the “Span” constant of the scale. 30 - 56
3.3.3 Display Data Units Code of the “Measure Units” displayed according the table below: SETTINGs CODE METRIC 00H ENGLISH 01H MIXED 02H Tab 7 – Units codes Total Units Code of the “Totalization Units” displayed according the table below: SETTINGs CODE KG 00H TONNES 01H POUNDS 02H TONS 03H LTONS Tab 8 – Total units code 04H Length Units Code of the “Lenght Units” displayed according the table below: SETTINGs CODE METERS 00H FEET Tab 9 – Length unit codes 01H Rate Units Code of the “Rate Units” displayed according the table below: SETTINGs CODE PERCENT % 00H KG/H 01H t/H 02H LB/H 03H TPH 04H LTPH 05H KG/MN 06H t/MN 07H LB/MN 08H T/MN 09H LT/MN 0AH Tab 10 – Rate units codes 31 - 56
Page 1 and 2: MINI CK101 Part No.: Pbus Ramsey MI
Page 3 and 4: INDEX About this manual ...........
Page 5 and 6: 1. PROFIBUS OVERVIEW 1.1 Introducti
Page 7 and 8: ───────────
Page 9 and 10: Write operations - Multiple registe
Page 11 and 12: same frequency the instrument updat
Page 13 and 14: 3 REGISTERS LIST 3.1 Description of
Page 15 and 16: Register Type Display (20) Display
Page 17 and 18: Language Register Type Time Format
Page 19 and 20: Register Type Weight Load Cell Zero
Page 21 and 22: Register Type Low rate delay Low ra
Page 23 and 24: Register Type Low Limit High Limit
Page 25 and 26: meanings, when the bit is 1 the ass
Page 27 and 28: O1.00 output 1 - mother board Comma
Page 29: 29 - 56
Page 33 and 34: Speed Damping The Value in seconds
Page 35 and 36: Load Cell Sensitivity The value in
Page 37 and 38: Test Duration The value in engineer
Page 39 and 40: UNITS Feet Meters MAX 10000 300 MIN
Page 41 and 42: 3.3.8 Alarms Rate deviation opt. En
Page 43 and 44: 3.3.10 Profibus Settings Address Ad
Page 45 and 46: 45 - 56
Page 47 and 48: EXAMPLE 2 - READ HOLDING REGISTER T
Page 49 and 50: MULTIPLE REGISTERS QUERY RESPONSE M
Page 51 and 52: 1.101 (bin) This number can be repr
Page 53 and 54: APPENDIX B INSTRUMENT CONFIGURATION
Page 55 and 56: Follows the contents of the Ramsey

Ramsey MINI CK101 Weight Integrator - Hoferick Engineering GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?