Programmer's Reference Manual Intermec Fingerprint® v8.70.0 ...

More documents

Recommendations

Info

Chapter —Image Transfer 10 Intermec Fingerprint v8.70.0/v10.0.0 Programmer´s Reference Manual
4 Character Sets and Fonts This chapter contains the various single-byte character sets, that can be selected using the NASC statement. Printouts samples are shown in the font “Swiss 721 BT”. Other fonts may not include all characters listed in the character sets. A short description of the multi-byte character set UTF-8 is included. Other double-byte character sets are not included, but are available separately on special request. Printout samples are shown for the fifteen scaleable single-byte fonts included in the Intermec Fingerprint v8.70.0/v10.0.0 firmware. It also describes the method of creating font aliases and contains character sets for the OCR-A, OCR-B, and DingDings fonts. For more information on character sets and fonts, refer to the Intermec Fingerprint v.8.xx, Font Reference Manual. Intermec Fingerprint v8.70.0/v10.0.0 Programmer´s Reference Manual 11
Page 1 and 2:
Programmer’s Reference Manual Int
Page 3 and 4:
Contents Contents 1 Introduction Fi
Page 5 and 6:
Contents INPUT$ ...................
Page 7 and 8:
3 4 5 Contents TRANSFER KERMIT ....
Page 9 and 10:
I Index Contents Actual Keyboard Ap
Page 11 and 12:
1 Introduction This chapter gives a
Page 13 and 14:
Differences between Fingerprint 8.7
Page 15 and 16:
Files in Intermec Fingerprint v8.70
Page 17 and 18:
2 Program Instructions This chapter
Page 19 and 20:
ABS Intermec Fingerprint v8.70.0/v1
Page 21 and 22:
ALIGN (AN) Chapter —Program Instr
Page 23 and 24:
ALIGN (AN), cont. Line: Box: Chapte
Page 25 and 26:
BARADJUST Chapter —Program Instru
Page 27 and 28:
BARFONT (BF) Chapter —Program Ins
Page 29 and 30:
BARFONT (BF), cont. Chapter —Prog
Page 31 and 32:
BARHEIGHT (BH) Purpose Statement sp
Page 33 and 34:
BARRATIO (BR) Intermec Fingerprint
Page 35 and 36:
BARSET, cont. Intermec Fingerprint
Page 37 and 38:
BEEP Purpose Statement ordering the
Page 39 and 40:
BREAK, cont. Intermec Fingerprint v
Page 41 and 42:
BUSY Chapter —Program Instruction
Page 43 and 44:
CHECKSUM Intermec Fingerprint v8.70
Page 45 and 46:
CLEANFEED Purpose Statement running
Page 47 and 48:
CLIP Chapter —Program Instruction
Page 49 and 50:
CLL, cont. Intermec Fingerprint v8.
Page 51 and 52:
COM ERROR ON/OFF Chapter —Program
Page 53 and 54:
COMSET Intermec Fingerprint v8.70.0
Page 55 and 56:
COMSET OFF Intermec Fingerprint v8.
Page 57 and 58:
COMSTAT Chapter —Program Instruct
Page 59 and 60:
COPY Purpose Statement for copying
Page 61 and 62:
COUNT&, cont. Chapter —Program In
Page 63 and 64:
CSUM Purpose Statement calculating
Page 65 and 66:
CUT ON/OFF Intermec Fingerprint v8.
Page 67 and 68:
DATEADD$ Chapter —Program Instruc
Page 69 and 70:
DATEDIFF Intermec Fingerprint v8.70
Page 71 and 72:
DBBREAK OFF Chapter —Program Inst
Page 73 and 74:
DBSTDIO Intermec Fingerprint v8.70.
Page 75 and 76:
DELETE Intermec Fingerprint v8.70.0
Page 77 and 78:
DEVICES Chapter —Program Instruct
Page 79 and 80:
DEVICES, cont. Intermec Fingerprint
Page 81 and 82:
DIR Purpose Statement specifying th
Page 83 and 84:
DIR, cont. Lines: Boxes: Chapter
Page 85 and 86:
END Chapter —Program Instructions
Page 87 and 88:
ERL Chapter —Program Instructions
Page 89 and 90:
ERR$ Chapter —Program Instruction
Page 91 and 92:
ERROR, cont. Chapter —Program Ins
Page 93 and 94:
FIELD Chapter —Program Instructio
Page 95 and 96:
FILE& LOAD Chapter —Program Instr
Page 97 and 98:
FILES Chapter —Program Instructio
Page 99 and 100:
FLOATCALC$ Purpose Function for cal
Page 101 and 102:
FONT (FT), cont. Chapter —Program
Page 103 and 104:
FONTNAME$ Intermec Fingerprint v8.7
Page 105 and 106:
FOR...TO...NEXT Intermec Fingerprin
Page 107 and 108:
FORMAT, cont. Chapter —Program In
Page 109 and 110:
FORMAT INPUT Intermec Fingerprint v
Page 111 and 112:
FORMAT$ Purpose Function for format
Page 113 and 114:
FORMAT$, cont. Examples Addition B$
Page 115 and 116:
FRE Chapter —Program Instructions
Page 117 and 118:
FUNCTEST$ Purpose Function returnin
Page 119 and 120:
GETASSOC$ Purpose Function for gett
Page 121 and 122:
GETPFSVAR Purpose Function for reco
Page 123 and 124:
GOSUB, cont. Chapter —Program Ins
Page 125 and 126:
HEAD Purpose Function returning the
Page 127 and 128:
IF...THEN...(ELSE) Chapter —Progr
Page 129 and 130:
IMAGE BUFFER MIRROR Purpose Stateme
Page 131 and 132:
IMAGE LOAD Chapter —Program Instr
Page 133 and 134:
IMAGES Chapter —Program Instructi
Page 135 and 136:
IMMEDIATE, cont. Chapter —Program
Page 137 and 138:
INKEY$ Chapter —Program Instructi
Page 139 and 140:
INPUT (IP), cont. Chapter —Progra
Page 141 and 142:
INPUT# Chapter —Program Instructi
Page 143 and 144:
INSTR Chapter —Program Instructio
Page 145 and 146:
KEY BEEP Chapter —Program Instruc
Page 147 and 148:
KEYBMAP$ Purpose Variable returning
Page 149 and 150:
KILL Chapter —Program Instruction
Page 151 and 152:
LAYOUT Purpose Statement for handli
Page 153 and 154:
LAYOUT, cont. Chapter —Program In
Page 155 and 156:
LAYOUT INPUT Chapter —Program Ins
Page 157 and 158:
LBLCOND Purpose Statement for overr
Page 159 and 160:
LED ON/OFF Purpose Statement for co
Page 161 and 162:
LEN Chapter —Program Instructions
Page 163 and 164:
LINE INPUT Chapter —Program Instr
Page 165 and 166:
LIST Chapter —Program Instruction
Page 167 and 168:
LISTPFSVAR Purpose Statement for li
Page 169 and 170:
LOC Chapter —Program Instructions
Page 171 and 172:
LSET Chapter —Program Instruction
Page 173 and 174:
MAG Chapter —Program Instructions
Page 175 and 176:
MAP Chapter —Program Instructions
Page 177 and 178:
MERGE Chapter —Program Instructio
Page 179 and 180:
MID$ Purpose Function returning a s
Page 181 and 182:
NAME DATE$ Chapter —Program Instr
Page 183 and 184:
NASC Chapter —Program Instruction
Page 185 and 186:
NASCD Chapter —Program Instructio
Page 187 and 188:
NORIMAGE (NI) Chapter —Program In
Page 189 and 190:
ON COMSET GOSUB Chapter —Program
Page 191 and 192:
ON ERROR GOTO Chapter —Program In
Page 193 and 194:
ON GOTO Purpose Statement for condi
Page 195 and 196:
ON KEY GOSUB Chapter —Program Ins
Page 197 and 198:
ON/OFF LINE Chapter —Program Inst
Page 199 and 200:
OPEN Chapter —Program Instruction
Page 201 and 202:
OPEN, cont. Chapter —Program Inst
Page 203 and 204:
PORTIN Chapter —Program Instructi
Page 205 and 206:
PRBAR (PB) Purpose Statement for pr
Page 207 and 208:
PRBOX, cont. Chapter —Program Ins
Page 209 and 210:
PRBOX, cont. This is line num
Page 211 and 212:
PRBUF Chapter —Program Instructio
Page 213 and 214:
PRINT (?) Purpose Statement for pri
Page 215 and 216:
PRINT# Chapter —Program Instructi
Page 217 and 218:
PRINTFEED (PF), cont. Chapter —Pr
Page 219 and 220:
PRINTONE# Chapter —Program Instru
Page 221 and 222:
PRPOS (PP) Chapter —Program Instr
Page 223 and 224:
PRSTAT Chapter —Program Instructi
Page 225 and 226:
PRTXT (PT) Purpose Statement for pr
Page 227 and 228:
PUT Chapter —Program Instructions
Page 229 and 230:
RANDOMIZE Chapter —Program Instru
Page 231 and 232:
REBOOT Purpose Statement for restar
Page 233 and 234:
REM (') Intermec Fingerprint v8.70.
Page 235 and 236:
RENDER ON/OFF Intermec Fingerprint
Page 237 and 238:
REPRINT ON/OFF Chapter —Program I
Page 239 and 240:
RETURN Intermec Fingerprint v8.70.0
Page 241 and 242:
REWINDVOID Chapter —Program Instr
Page 243 and 244:
RSET Intermec Fingerprint v8.70.0/v
Page 245 and 246:
SAVE Intermec Fingerprint v8.70.0/v
Page 247 and 248:
SETASSOC Chapter —Program Instruc
Page 249 and 250:
SETSTDIO Intermec Fingerprint v8.70
Page 251 and 252:
SETUP Chapter —Program Instructio
Page 253 and 254:
SETUP, cont. Intermec Fingerprint v
Page 255 and 256:
SETUP KEY Intermec Fingerprint v8.7
Page 257 and 258:
SETUP WRITE, cont. Chapter —Progr
Page 259 and 260:
SORT Purpose Statement for sorting
Page 261 and 262:
SPACE$ Purpose Function returning a
Page 263 and 264:
STOP Intermec Fingerprint v8.70.0/v
Page 265 and 266:
STORE INPUT Intermec Fingerprint v8
Page 267 and 268:
STR$ Chapter —Program Instruction
Page 269 and 270: SYSHEALTH Intermec Fingerprint v8.7
Page 271 and 272: SYSHEALTH$ Chapter —Program Instr
Page 273 and 274: SYSVAR, cont. Remarks 0-13. Reserve
Page 275 and 276: SYSVAR, cont. Intermec Fingerprint
Page 277 and 278: SYSVAR, cont. Chapter —Program In
Page 279 and 280: Intermec Fingerprint v8.70.0/v10.0.
Page 281 and 282: TAGFIELD, cont. Chapter —Program
Page 283 and 284: TAGFORMAT, cont. 10 TAGFIELD "@ID"
Page 285 and 286: TAGREAD Purpose Statement used to r
Page 287 and 288: TESTFEED Chapter —Program Instruc
Page 289 and 290: TIME$ Purpose Variable for setting
Page 291 and 292: TIMEDIFF Chapter —Program Instruc
Page 293 and 294: TRANSFER NET Chapter —Program Ins
Page 295 and 296: TRANSFER STATUS Chapter —Program
Page 297 and 298: TRANSFER$ Chapter —Program Instru
Page 299 and 300: TRON/TROFF Chapter —Program Instr
Page 301 and 302: VERBON/VERBOFF Chapter —Program I
Page 303 and 304: WEEKDAY Purpose Function returning
Page 305 and 306: WEEKNUMBER Intermec Fingerprint v8.
Page 307 and 308: XORMODE ON/OFF Chapter —Program I
Page 309 and 310: External Command; Account Secret, c
Page 311 and 312: 3 Image Transfer This chapter descr
Page 313 and 314: Image Format Chapter —Image Trans
Page 315 and 316: Chapter —Image Transfer Example 2
Page 317 and 318: Chapter —Image Transfer The image
Page 319: Specification of the RLL format Ch
Page 323 and 324: Chapter —Character Sets and Fonts
Page 349 and 350: Bitmap Fonts Font Aliases Intermec
Page 351 and 352: OCR-B 10 Pitch BT Character Set Cha
Page 353 and 354: 5 Bar Codes This chapter list the b
Page 355 and 356: Supported Bar Codes Intermec Finger
Page 357 and 358: One-and Two-Dimensional Bar Codes C
Page 359 and 360: Code 128 Separate Instructions BART
Page 361 and 362: Data Matrix Separate Instructions B
Page 363 and 364: EAN-13 Separate Instructions BARTYP
Page 367 and 368: MaxiCode Separate Instructions BART
Page 369 and 370: MicroPDF417 BARSET Instruction Inte
Page 371 and 372:
PDF417 Separate Instructions BARTYP
Page 373 and 374:
QR Code BARSET Instruction Intermec
Page 375 and 376:
RSS-14 Separate Instructions Interm
Page 377 and 378:
RSS-14 Stacked Separate Instruction
Page 379 and 380:
RSS-14 Stacked Omnidirectional Sepa
Page 381 and 382:
RSS-14 Expanded Separate Instructio
Page 383 and 384:
Chapter —Bar Codes Remarks The RS
Page 385 and 386:
UPC-E Separate Instructions BARTYPE
Page 387 and 388:
Composite Bar Codes Introduction (0
Page 389 and 390:
Chapter —Bar Codes EAN-13 Composi
Page 391 and 392:
Chapter —Bar Codes MicroPDF is a
Page 393 and 394:
EAN13 Composite with CC-A or CC-B S
Page 395 and 396:
UPC-A Composite with CC-A or CC-B S
Page 397 and 398:
Input Data Chapter —Bar Codes No.
Page 399 and 400:
Input Data Chapter —Bar Codes No.
Page 401 and 402:
Chapter —Bar Codes 1 /. There are
Page 403 and 404:
Intermec Fingerprint v8.70.0/v10.0.
Page 405 and 406:
Page 407 and 408:
Chapter —Bar Codes 1 /. There are
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
6 RFID Tag Formats This chapter lis
Page 417 and 418:
SGTIN-96 FIELD NUMBER OF DIGITS RAN
Page 419 and 420:
GIAI-96 FIELD NUMBER OF DIGITS RANG
Page 421 and 422:
(01)10614141007346(21)2 AI GTIN Com
Page 423 and 424:
UCODE HSL (ISO 18000-6B) Tag Memory
Page 425 and 426:
Gen 2 (EPC Class 1 Generation 2) Ta
Page 427 and 428:
7 Error Messages This chapter list
Page 429 and 430:
Code Message/Explanation 1005 Out o
Page 431 and 432:
A Keyboards This appendix illustrat
Page 433 and 434:
EasyCoder PF2i/4i/4ci, cont. Positi
Page 435 and 436:
EasyCoder PM4i, cont. Position Numb
Page 437 and 438:
EasyCoder PX4i/6i, cont. Position N
Page 439 and 440:
Mapping the Keyboard Intermec Finge
Page 441 and 442:
I Index This appendix lists relevan
Page 443 and 444:
CLEAR instruction 36 CLIP instructi
Page 445 and 446:
images names, listing 123 names, re
Page 447 and 448:
TRANSFER ZMODEM 286 TRON/TROFF 289
Page 449 and 450:
search string 133 secret instructio
Page 451 and 452:
Appendix I—Index Intermec Fingerp
Page 454:
Intermec Technologies Corporation C
show all

Programmer's Reference Manual Intermec Fingerprint® v8.70.0 ...

Create successful ePaper yourself

Delete template?

Save as template?