TUBE & PIPE - Tradelink

tube & pipe 

copper tuBe 15.1 

polylag / selector information / codes / for airconditioning & refrigeration 

steel pipes 15.8 

to as1074 / to ansi B36.10 

stainless steel pipe 15.11 

stainless steel tuBe 15.13 

upvc pressure pipe 15.17 

permapipe 15.18

copper tube 

ApplicAtions 

copper tubes from tables A and b are suitable for use with 

compression, capillary and brazed joints. 

copper tubes from table c are suitable for use with capillary and 

brazed joints only. 

copper tubes from table D are suitable for use with capillary and 

brazed joints, only in the ‘hard drawn’ condition. 

copper tubes from table D shall not be bent. 

copper tubes from tables A, b or c may be supplied in the ‘hard 

drawn’ or ‘annealed’ condition. 

copper tubes from table D are only supplied in the ‘hard drawn’ 

condition. 

copper tube identificAtion 

crane enfield copper tubes, manufactured to meet the requirements 

of AS 1432, are colour coded with an ink mark along the tube with 

the manufacturers trademark, "AuStrALiA" the country of origin, 

the nominal size, thickness type and the letters "bQ" where tubes are 

"bendable" temper etc. 

crANe eNFieLD AuStrALiA DN50A bQ 

in addition Hard Drawn and bendable copper tubes are incised at 

0.5m intervals with the manufacturers trademark, the Standards 

Australia Licence number, the Standards Mark, the Australian 

Standard number, nominal size, thickness type and "bQ" to identify 

bendable temper tubes, etc. 

ceM Lic 940 i>>>>>i AS1432 DN 15A bQ 

Four colours are used to represent the tube specification types: 

type A - Green type c - red 

type b - blue type D - black 

it is to be noted that the tubes are made from the one alloy and are of 

similar quality. the word "tYpe" refers to the thickness categories 

with type A being the thickest and type D being the thinnest tube 

permitted for use by water authorities. 

Also available is large diameter copper tube not in AS 1432 range. 

these are projections of AS 1432. 

Nom 

Size 

mm 

properties 

copper tubing to AS 1432 is manufactured from alloy designation 122 

of AS 2738.2 

Melting point 1083°c 

Density 8.94 x 103 kg/m3 @ 20°c 

thermal expansion 0.177mm/ 10°c.m 

thermal conductivity 295 - 355 W/mK 

Specific Heat capacity 385 J/kgK 

composition Alloy c12200 copper = 99.90%min 

phosphorus = 0.015-0.040% 

June 2010 

Nom 

Wt 

A b D 

pSW 

(kpa) 

Nom 

Wt 

pSW 

(kpa) 

Nom 

Wt 

pSW 

(kpa) 

203.2 1.63 590 

225 3.25 1010 2.64 820 2.03 650 

254 3.25 910 2.64 730 2.03 580 

corrosion rAtings of copper 

Acetone A butane A 

Acids - carbon Dioxide (m) b 

chromic D carbon Monoxide A 

citric A chlorine c 

Hydrochloric c Freon A 

Nitric D Hydrogen A 

phosphoric b Hydrogen Sulphide (m) D 

Sulphuric c Methane A 

tanic A Natural Gas b 

tartaric A Nitrogen A 

Alcohols A oxygen A 

Aniline Dyes c propane A 

Animal/excreta and Steam A 

Decomposed undiluted Sulphur Dioxide (m) b 

urine D Gasoline A 

Ashes D Kerosene A 

Asphalt A Lacquers A 

Atmosphere - industrial A Magnesite D 

Marine A Mercury and Salts D 

rural A Silver Salts D 

beer A Sodium chloride b 

benzene, benzol A Sodium Hypochlorite c 

bleaching powder b Sugar Solution A 

brines b trichlorethylene (dry) A 

carbon Varnish - Solvents A 

tetrachlorine (m) b Water - 

Fruit Juices b carbonated b 

Feul oil A potable A 

Gases - Sea Water b 

Acetylene D Mine Water c 

Ammonia (m) D Soapy A 

bromine (m) c Sewage A 

rAtings 

A excellent under most conditions. 

b good May be considered in place of “A” when some other 

property governs use. 

c fair May only have limited life. 

d poor Not recommended. 

bendAble temper piping 

in certain circumstances it may be desirable to use a straight tube 

which has improved bending characteristics compared to normal 

hard drawn temper tube. to fill this need, a selected size range of 6m 

straight length copper tubes is available in bendable temper. 

these particular tubes are capable of being bent, without local 

annealing, to minimum centreline radii of 45mm, 60mm and 85mm for 

nominal sizes DN15, DN18 and DN20 respectively. Available sizes: 

DN 15A 12.70 x 1.02mm DN 18b 15.88 x 1.02mm 

DN 15b 12.70 x 0.91mm DN 18c 15.88 x 0.91mm 

DN 15c 12.70 x 0.71mm DN 20A 19.05 x 1.42mm 

DN 18A 15.88 x 1.22 mm DN 20b 19.05 x 1.02mm 

DN 20c 19.05 x 0.91mm 

standards Applicable to copper and copper Alloy tubes 

AS 1432 copper tubes for plumbing, gasfitting & drainage applications. 

AS 1572 copper & copper alloys - seamless tubes for engineering 

purposes. 

AS 1571 copper - seamless tubes for air conditioning & refrigeration. 

AS 1569 copper & copper alloys - seamless tubes for heat exchangers. 

AS 3795 copper alloy tubes for plumbing & drainage applications. 

tube & pipe copper tube 

15.1

tube & pipe copper tube polylAg 

15.2 

copper tube poLYLAG 

‘polylAg’ pre-insulAted copper tube 

A comprehensive range of pre-insulated tubes is available for use 

in a variety of end use applications e.g. domestic hot water lines, 

burying in corrosive soils, laying under floors and concrete slabs 

(where approved), chasing into walls and masonary, pipework 

exposed to aggressive environments. the insulation is moisture 

resistant and chemically inert. 

the copper tubing component is covered by StandardsMark License 

No. 940, with the required marking to this effect, which conforms to 

AS1432-1990 specification. 

polylag premium of nominal sizes 15 to 25 consists of a seamless 

extruding coating, of lightly foamed flexible polyvinyl chloride (pVc), 

over copper tubing. 

polylag of nominal sizes 32 to 50 consists of micro-cellular 

polyethylene (polythene) coating, over copper tubing. 

properties - pVc 

Specific Gravity (20°c) 1.1 - 1.7 

Melting range 120°c - 170°c 

Decomposition point >200°c 

Flash point None 

Flammable Limits Self extinguishing 

Auto ignition point None 

Water Solubility (G/L) 

General 

Nil 

A foamable flexible pVc compound, containing a combination of heat 

and uV stabilizers. 

coating Form: Generally 1.0mm thick, plus 1.0mm castellation, for an 

overall thickness with standoff 2.0 to 2.5mm. 

properties - polythene 

Melting point 109°c 

"VicAt" Softening point 91°c 

thermal conductivity 0.0034 Joules cM/cM Sec°c 

Specific Heat 0.55 cAL/GM 

Decomposition point 280°c - 300°c 

coating Form Generally 2.0mm thickness 

it is to be noted that lagging consisting of hair, felt or otherfibrous 

material should be used in only dry, well ventilated places. the use of 

such lagging in damp or confined, poorly ventilated environments is 

not recommended. 

thermAl trAnsmission 

thermal conductivity W/mK: 0.052 

thermal resistance m2K/W (pVc): 0.028 

note: As the only known test methods in this country, are for flat 

test specimens and not tubular lagging on pipe, care should be taken 

in extrapolating the above results to tubular form. 

operAtionAl chArActeristics 

Maximum Service temperature +75°c 

Minimum Service temperature -45°c 

Normal operating range -10° to +60°c 

corrosion 

the insulation material is resistant to dilute acids & alkalis, which 

makes it highly suitable for barrier protection of the copper tubing, 

in aggressive environments. in underground use, it is necessary to 

ensure that waterproof joints are made, to prevent the ingress of 

chemical laden groundwater. 

product identificAtion 

the coating material is colour coded (iSo) GreeN to AS1345-1972, 

for potable water. Semi-continuous external markings identify the 

Manufacturer, tube material, Diameter (DN), table type, and brand 

Name. 

e.g. crane enfield Australia copper tube DN25 c polylag premium. 

the coating material is colour coded lilac for recycled water 

applications. 

stAndArd size rAnge 

6m straights (mm) nominal size 18m coils (mm) 

12.70 x 1.02 DN15A 12.70 x 1.02 

12.70 x 1.02 DN15b 12.70 x 0.91 

12.70 x 0.71 DN15c 12.70 x 0.71 

15.9 x 1.22 DN18A 

15.9 x 1.02 DN18b 15.9 x 1.02 

15.9 x 0.91 DN18c 15.9 x 0.91 

19.1 x 1.02 DN20b 19.1 x 1.02 

19.1 x 0.91 DN20c 19.1 x 0.91 

25.4 x 1.22 DN25b 

25.4 x 0.91 DN25c 

31.8 x 1.22 DN32b 

37.1 x 1.22 DN40b 

50.8 x 1.22 DN50b 

other sizes from DN15 to DN150 may be available on request. 

the information provided in this catalogue is based on original manufacturers’ designs and specifications and subject to change without 

notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

copper tube SeLector iNForMAtioN 

June 2010 

Nom. Size mill Size 

(mm) 

type A 

preViouS Size No. lgtH 

buNDle 

No. coilS 

cArtoN 

pSW (kpa) Nom. WgHt 

(kg/m) 

DN 6 6.4 x 0.91 1/4" x 20G 200 6 12,080 0.139 

DN 8 7.9 x 0.91 5/16" x 20G 100 5 9,380 0.180 

DN 10 9.5 x 1.0 3/8" x 19G 150 4 8,730 0.243 

DN 15 12.7 x 1.0 1/2" x 19G 100 3 6,380 0.335 

DN 18 15.9 x 1.2 5/8" x 18G 100 2 6,090 0.503 

DN 20 19.1 x 1.4 3/4" x 17G 80 2 5,900 0.704 

DN 25 25.4 x 1.6 1" x 16G 40 19 (crate) 5,070 1.089 

DN 32 31.8 x 1.6 1¼" x 16G 30 14 (crate) 4,010 1.380 

DN 40 38.1 x 1.6 1½" x 16G 21 3,310 1.671 

DN 50 50.8 x 1.6 2" x 16G 14 2,460 2.253 

DN 65 63.5 x 1.6 2½" x 16G 7 1,960 2.835 

DN 80 76.2 x 2.0 3" x 14G 7 2,030 4.232 

DN 90 88.9 x 2.0 3½" x 14G 3 1,740 4.957 

DN 100 101.6 x 2.0 4" x 14G 3 1,520 5.682 

DN 125 127.0 x 2.0 5" x 14G 2 1,210 7.131 

DN 150 152.4 x 2.6 6" x 12G 2 1,310 11.114 

DN 200 203.2 x 2.6 8" x 12G 2 920 14.884 


(mm) 

type b 


buNDle 

No. coilS 

cArtoN 


(kg/m) 

DN 6 6.4 x 0.71 1/4" x 20G 200 6 8,780 0.113 

DN 8 7.9 x 0.71 5/16" x 22G 100 5 6,870 0.144 

DN 10 9.5 x 0.91 3/8" x 20G 150 4 7,680 0.221 

DN 15 12.7 x 0.91 1/2" x 20G 100 3 5,630 0.302 

DN 18 15.9 x 1.0 5/8" x 19G 100 2 5,020 0.426 

DN 20 19.1 x 1.0 3/4" x 19G 80 2 4,140 0.517 

DN 25 25.4 x 1.2 1" x 18G 40 19 (crate) 3,700 0.829 

DN 32 31.8 x 1.2 1¼" x 18G 30 14 (crate) 2,940 1.047 

DN 40 38.1 x 1.2 1½" x 18G 21 2,430 1.265 

DN 50 50.8 x 1.2 2" x 18G 14 1,810 1.700 

DN 65 63.5 x 1.2 2½" x 18G 7 1,440 2.136 

DN 80 76.2 x 1.6 3" x 16G 7 1,620 3.417 

DN 90 88.9 x 1.6 3½" x 16G 4 1,390 3.999 

DN 100 101.6 x 1.6 4" x 16G 3 1,210 4.581 

DN 125 127.0 x 1.6 5" x 16G 2 970 5.744 

DN 150 152.4 x 2.0 6" x 14G 2 1,000 8.581 

DN 200 203.2 x 2.0 8" x 14G 2 730 11.479 

tube & pipe copper tube Selector iNformAtioN 

15.3

tube & pipe copper tube Selector iNformAtioN 

15.4 

copper tube SeLector iNForMAtioN 


(mm) 

stAndArd lengths 

straights DN 125 and below 6m 

DN 150 and above 4, 5 or 6m random lengths 

coils DN 8 and below 30 metres 

DN 10 and above 18 metres 

plus a full range to international Standards. 

pSW: Safe working pressure is the recommended maximum 

continuous pressure to which the tubes should be subjected to for 

the design life of the plumbing installation. these pressures are 

based on tubing in the annealed temper to allow for the effects of 

softening during normal jointing operations. (ref AS1432-1996) 

type c 


buNDle 

No. coilS 

cArtoN 

copper tube to AS 1432 - 1996 from crane enfield Metals. 

High performance copper tubing with the competitive edge 

phone 1800 043 117 for your nearest crane office. 


(kg/m) 

DN 10 9.5 x 0.71 3/8" x 22G 150 4 5,650 0.176 

DN 15 12.7 x 0.71 1/2" x 22G 100 3 4,170 0.239 

DN 18 15.9 x 0.91 5/8" x 20G 100 2 4,440 0.383 

DN 20 19.1 x 0.91 3/4" x 20G 80 2 3,670 0.464 

DN 25 25.4 x 0.91 1" x 20G 40 19 (crate) 2,720 0.626 


(mm) 

type D 


buNDle 

No. coilS 

cArtoN 


(kg/m) 

DN 32 31.8 x 0.91 1¼" x 20G 30 2,160 0.789 

DN 40 38.1 x 0.91 1½" x 20G 21 1,790 0.951 

DN 50 50.8 x 0.91 2" x 20G 14 1,340 1.276 

DN 65 63.5 x 0.91 2½" x 20G 7 1,070 1.601 

DN 80 76.2 x 1.2 3" x 18G 7 1,200 2.571 

DN 90 88.9 x 1.2 3½" x 18G 3 1,030 3.007 

DN 100 101.6 x 1.2 4" x 18G 3 900 3.442 

DN 125 127.0 x 1.4 5" x 17G 2 830 5.013 

DN 150 152.4 x 1.6 6" x 16G 2 800 6.908 

AS 1432 Lic 940 

Standards Australia 



copper tube coDeS 

copper tube trAdelink codes 

June 2010 

ANNeAleD 

coilS 

coDe 

type A 

HArD 

DrAWN 

StrAigHt 

coDe 

DN6 093803 093881 

DN8 093806 093886 

DN10 093815 093897 

polylAg 

ANN coil 

coDe 

polylAg 

HD 

StrAigHt 

coDe 

DN15 093824 093906 094093 094132 

DN18 093837 093924 

DN20 093848 093939 094364 

DN25 093857 093954 

DN32 093861 093966 

DN40 093863 093975 

DN50 093984 094162 

DN65 093996 

DN80 094011 

DN90 

DN100 094023 

DN125 094025 

DN150 094039 

DN200 094052 

ANNeAleD 

coilS 

coDe 

DN10 093809 

type c 

HArD 

DrAWN 

StrAigHt 

coDe 

polylAg 

ANN coil 

coDe 

polylAg 

HD 

StrAigHt 

coDe 

DN15 093818 093900 094087 094126 

DN18 093833 093918 094096 094135 

DN20 093839 093930 094102 094141 

DN25 093851 093948 094147 

DN6 

DN8 

ANNeAleD 

coilS 

coDe 

type b 

HArD 

DrAWN 

StrAigHt 

coDe 

polylAg 

ANN coil 

coDe 

DN10 093812 093894 094084 

polylAg 

HD 

StrAigHt 

coDe 

DN15 093821 093903 094090 094129 

DN18 093836 093921 094099 094138 

DN20 093842 093933 094105 094144 

DN25 093854 093951 094150 

DN32 093860 093963 094153 

DN40 093972 094156 

DN50 093981 094159 

DN65 093993 094165 

DN80 094008 094171 

DN90 

DN100 094020 094174 

DN125 094024 

DN150 094037 

DN200 094051 

type D 

HArD DrAWN StrAigHt 

coDe 

DN32 093960 

DN40 093969 

DN50 093978 

DN65 093990 

polylAg HD StrAigHt 

coDe 

DN80 094005 094168 

DN90 

DN100 094017 094177 

DN125 

codes for lArge diAmeter copper tube not in the As 1432 rAnge 

DN150 094036 

extrapolating from AS 1432 the following DN250 copper tube is approximately equivalent to a type b. 

Nom. 

Size 

mill Size 

mm 

leNgtHS - m 

4.0 4.5 5.0 5.5 

DN250 10” x 12G 094094 094095 094097 094098 

tube & pipe copper tube coDeS 

15.5

tube & pipe copper tube for AircoNDitioNiNg & refrigerAtioN 

15.6 

copper tube For AircoNDitioNiNG & reFriGerAtioN 

An extensive range of copper tube is manufactured specifically to 

cater for the special requirements of refrigeration gas lines and 

airconditioning. these tubes comply with the required internal 

cleanness limits specified in AS 1571:copper - Seamless tubes for 

Airconditioning and refrigeration. 

tubes are factory cleaned and supplied sealed to maintain the 

cleanness of the bore under normal conditions of handling and 

storage. 

ink mArking 

the tube is identified with an ink marking along its length stating 

the Manufacturers Name, country of origin, conforming standard, 

temper and Size. 

eg. “crANe copper tube AuStrALiA AS/NZS 1571 1/2h 19.05 X 0.91” 

pAckAging 

As drawn straight length tubes are capped on each end and 

packaged in bundles. 

Annealed coils are encapsulated with heat shrunk plastic. caps are 

included for placement on tube after the plastic is removed. the 

capping for airconditioning and refrigeration grade tubing is colour 

coded yellow. 

mAnufActuring stAndArds AVAilAble 

code 

American 

copper Alloy no. chemical requirement 

AStM b280 

Australian 

uNS. c12200 cu 99.9% min. 

po.015-0.40% 

AS1571 c122 cu 99.9% min. 

po.015% min. 

0.040% max. 

cleAnness requirements 

All tubes are cleaned and sample tested to meet the residue 

requirement as specified by the codes at 0.038 g/m3 (0.0035g/m 2). 

tube integrity 

All tubes are electronically tested by eddy current method, to the 

requirements of AStM e243. 

positiVe pressure lines 

As drawn copper tube to AS 1571 is permitted, with dimensions as 

specified in AS 1432 type b. For nominal sizes DN 15 and below, the 

thickness shall not be less than 1.02mm. 

VAcuum lines 

Sizes are the same as for positive pressure lines but either as drawn 

or annealed temper tubes may be used. 

note: AS 1571 tube is unavailable, tube must be cleaned as 

specified in AS 2896. 

medicAl gAses grAde copper tubes 

interpolation of allowable design stress as defined by table d7 of As4041 for the below temperatures. 

Safety standards for oxygen and other medical gases require the use 

of specially cleaned tubing in order to prevent gas contamination, or 

potential explosions. 

oxygen under pressure may cause spontaneous combustion of 

residual organic drawing oils, if left inside tubes after manufacture. 

Similarly, oils or other contaminants could cause severe patient 

problems if not removed prior to installation. 

crane enfield Metals are able to provide a wide range of tubes to 

several international standards for this highly sensitive work. 

code no. code description 

Australian AS2896 Medical gas systems - installation and 

testing of non-inflammable medical gas 

pipeline systems. 

Australian AS1169 installation and testing of medical gas 

supply systems. 

American AStMb819 Medical gas systems tubing. 

Although tubes are supplied specially cleaned and capped ready 

for use, it is the duty of the installer that all regulations covering 

installation practices are complied with. 

particular attention should be given to: 

1. Storage and handling. 

2. Site cleaning of tubes and components. 

3. pipeline gas purging during brazing. 

4. use of approved filler metals and fluxes. 

5. post brazing cleaning and visual inspection of all joints. 

6. Full compliance with pressure and containment testing before 

final approval and use. 

the methods used by crane enfield Metals for the cleaning and 

capping of medical grade copper tubing is a documented procedure 

under Quality Systems Standards AS3902-1987ASo 9002:1987, as 

covered by Licence No. 0590. the capping for Medical grade tubing 

is colour coded green and the ink marking includes “MeDicAL GAS”. 

r410A rAted tube 

the r410A rated copper tube is especially designed to comply with 

AS4041 pressure piping code. our r410A rated copper tube is 

capable of withstanding 

working pressures of 4121 kpa when the refrigerant is operating 

at a temperature of 65°c, which is the recommended operating 

temperature as per AS/NZS 1677 refrigeration systems. the r410A 

rated copper tube is distinguished by rose colour capping and 

“r410A rAteD” becomes part of the ink marking. 

key for table page 15.07 

pSW = 2,000 x SD x tm 

D – tm 

SD = Maximum allowable design stress for annealed 

copper in mega pascals 

tm = Minimum thickness any point (mm) 

D = Maximum mean outside diameter (mm) 

*Safe working pressures calculated for annealed copper. 

temperAture (°c) 50.0 55.0 60.0 65.0 70.0 75.0 

SD (mpa) 41 38.6 36.83 35.55 34.63 34 



copper tube For AircoNDitioNiNG & reFriGerAtioN 

June 2010 

ANNeAleD coil 

NomiNAl 

kg/metre 

*SAfe WorKiNg preSSure kpa 

trADeliNK 

coDe 

Size (mm) iNcHeS 

50-75°c 100-125°c 150-175°c 175-200°c 

x Wt 

x SWg 

SD = 33.9 SD = 32.7 SD = 28 SD = 21.9 

4.8 x 0.91 3/16”x 20 0.098 13940 13450 11520 9000 094438 

4.8 x 0.71 3/16”x 22 0.081 10400 10040 8600 6700 

4.8 x 0.56 3/16”x 24 0.066 7950 7600 6580 5100 

6.4 x 1.22 1/4”x 18 0.176 14040 13540 11600 9000 

6.4 x 0.91 1/4”x 20 0.139 9950 9595 8215 6400 094440 

6.4 x 0.71 1/4”x 22 0.113 7520 7250 6200 4850 

6.4 x 0.56 1/4”x 24 0.091 5795 5640 4830 3775 

7.9 x 0.91 5/16”x 20 0.18 7840 7580 6470 5060 094444 

7.9 x 0.71 5/16”x 22 0.144 5965 5750 4920 3850 094443 

7.9 x 0.56 5/16”x 24 0.116 4620 4450 3800 2980 

9.5 x 0.91 3/8”x 20 0.221 6395 6170 5280 4100 094446 

9.5 x 0.71 3/8”x 22 0.176 4890 4700 4030 3150 

9.5 x 0.56 3/8”x 24 0.141 3795 3660 3130 2450 

12.7 x 0.91 1/2”x 20 0.302 4670 4500 3860 3020 094449 

12.7 x 0.81 1/2”x 21 0.271 4125 3980 3400 2665 

12.7 x 0.71 1/2”x 22 0.239 3590 3460 2965 2320 

12.7 x 0.56 1/2”x 24 0.191 2800 2700 2315 1810 

15.9 x 1.02 5/8”x 19 0.426 093970 

15.9 x 0.91 5/8”x 20 0.383 3680 3550 3040 2380 094452 

15.9 x 0.81 5/8”x 21 0.343 3250 2140 2690 2100 

15.9 x 0.71 5/8”x 22 0.303 2840 2740 2340 1830 

15.9 x 0.56 5/8”x 24 0.241 2220 2144 1835 1435 

19.1 x 1.22 3/4” x 18 0.611 093971 

19.1 x 0.91 3/4” x 20 0.464 3030 2930 2500 1960 094455 

19.1 x 0.71 3/4” x 22 0.366 2340 2260 1940 1500 

22.2 x 0.91 7/8”x 20 0.545 2595 2500 2145 1670 094457 

StrAigHt leNgtHS, H/D 

6.4 x 0.91 1/4”x 20 0.139 9950 9590 8200 6425 094395 

9.5 x 0.91 3/8”x 20 0.221 6395 6170 5280 4130 094398 

12.7 x 1.02 1/2”x 19 0.335 5280 5095 4360 3400 094402 

12.7 x 0.91 1/2”x 20 0.302 4670 4500 3860 3020 094401 

15.9 x 1.02 5/8”x 19 0.426 092652 

15.9 x 0.91 5/8”x 20 0.383 3680 3550 3040 2380 094404 

19.1 x 1.22 3/4”x 18 0.611 092654 

19.1 x 1.02 3/4”x 19 0.416 3420 3300 2825 2200 094406 

19.1 x 0.91 3/4”x 20 0.464 3035 2930 2500 1960 094407 

22.2 x 1.63 7/8” x 16 0.943 094408 

22.2 x 1.22 7/8” x 18 0.721 3525 3400 2900 2280 094409 

22.2 x 0.91 7/8” x 20 0.545 2600 2500 2145 1675 094410 

25.4 x 1.63 1”x 16 1.088 097293 

25.4 x 1.22 1”x 18 0.829 3060 2950 2530 1980 094412 

25.4 x 0.91 1”x 20 0.626 2260 2180 1865 1460 094411 

28.6 x 1.83 1 1/8” x 15 1.374 092657 

28.6 x 1.22 1 1/8” x 18 0.938 2700 2600 2235 1750 094414 

28.6 x 0.91 1 1/8” x 20 0.708 2000 1925 1650 1290 094413 

31.8 x 2.03 1 1/4”x 14 1.694 097296 

31.8 x 1.22 1 1/4”x 18 1.047 2425 2340 2000 1565 094432 

31.8 x 0.91 1 1/4”x 20 0.789 1970 1725 1480 1155 094431 

34.9 x 2.03 1 3/8”x 14 1.875 092658# 

34.9 x 1.63 1 3/8”x 16 094566 

34.9 x 1.22 1 3/8”x 18 1.156 2200 2125 1820 1450 094415 

34.9 x 0.91 1 3/8”x 20 0.87 1630 1570 1345 1050 094416 

38.1 x 1.22 1 1/2”x 18 1.265 2010 1940 1660 1300 094418 

38.1 x 0.91 1 1/2”x 20 0.951 1490 1435 1230 960 094417 

41.3 x 2.41 1 5/8”x 12.5 2.63 092659# 

41.3 x 1.63 1 5/8” x 16 094567 

41.3 x 1.22 1 5/8” x 18 1.373 1850 1785 1530 1195 094420 

41.3 x 0.91 1 5/8” x 20 1.032 1370 1320 1130 885 094419 

44.5 x 1.22 1 3/4”x 18 1.483 1700 1650 1415 1100 094421 

44.5 x 0.91 1 3/4”x 20 1.14 1270 1225 1050 820 

50.8 x 1.63 2”x 16 2.253 2015 1945 1665 1300 

50.8 x 1.22 2”x 18 1.7 1495 1445 1235 965 094425 

50.8 x 0.91 2” x 20 1.276 1110 1070 915 715 094424 

54.0 x 1.63 2 1/8”x 16 2.398 1890 1825 1560 1220 094421 

54.0 x 1.22 2 1/8”x 18 1.809 1400 1350 1160 900 094422 

54.0 x 0.91 2 1/8”x 20 1.357 1045 1000 860 675 094427 

63.5 x 1.22 2 1/2” x 18 094754 

66.7 x 1.63 2 5/8” x 16 2.981 1520 1470 1260 985 

66.7 x 1.22 2 5/8” x 18 2.245 1135 1095 935 730 094429 

76.2 x 1.63 3”x 16 3.417 1330 1280 1100 860 094756 

101.6 x 1.63 4”x 16 4.581 990 955 820 640 

bold typeface denotes r410A rated tube. # Denotes r410A tube requires safety shut off limit of 3800 kpa. 

tube & pipe copper tube for AircoNDitioNiNg & refrigerAtioN 

15.7

tube & pipe Steel pipeS to AS1074 

15.8 

SteeL pipeS to AS1074 

steel pipes to As1074 

NomiNAl 

Size 

DN 

mm 

outSiDe 

DiAm. 

Approx. 

mm 

product description 

Steel tubeS 

tHicKNeSS 

meD. 

mm 

HVy. 

mm 

Steel SocKetS 

miN oD 

mm 

miN 

lgtH 

mm 

6 10.3 2.0 2.6 15 19 

8 13.5 2.3 2.9 18.5 27 

10 17.2 2.3 2.9 22 28 

15 21.3 2.6 3.2 27 37 

20 26.9 2.6 3.2 32.5 39 

25 33.7 3.2 4.0 39.5 46 

32 42.4 3.2 4.0 49 51 

40 48.3 3.2 4.0 56 51 

50 60.3 3.6 4.5 68 60 

65 76.1 3.6 4.5 84 69 

80 88.9 4.0 4.8 98 75 

100 114.3 4.5 5.4 124 87 

125 139.7 4.8 5.4 151 96 

150* 165.1 4.8 5.4 178 96 

* Not standard. 

pipe lengths are available with plain, screwed or socketed ends. 

pipe, for general mechanical and low pressure recirculation 

applications. Manufactured by cold-forming process enhances the 

strength, hardness and surface finish of the pipe and produces 

product to tight dimensional tolerances. 

Available in black, painted and galvanised finishes. the ends of the 

pipe are bevelled to remove any burrs and are available screwed on 

one or both ends in accordance with AS1074-1989. 

specificAtion 

Manufactured and tested to meet the requirements of the following 

specifications: 

AS1450-1983 Steel tubes for Mechanical purposes (Grade c200 erW). 

AS1163-1991 Structural Steel Hollow Sections (Grade c250). 

AS1074-1989 Steel tubes and tubulars threaded or suitable for 

threading with pipe threads of witworth form. 

mechAnicAl properties 

Minimum Yield Strength 250 (Mpa) 

Minimum tensile Strength 320 (Mpa) 

Minimum elongation in 5.65 √S 22 (%) 

supply conditions 

Surface Finish black/painted/Galvanised 

Straightness 

thickness 

Dimension tolerance 

} 

} 

} 

refer to Aust. 

Standards 

Length tolerance +25mm/-0mm 

if tighter length tolerances are required, they must be specified at 

time of order. 

length limitAtions 

Min Length 

(20Nb-100Nb) black/painted 4.2m 


(20Nb-100Nb) Galvanised 4.5m 


mAx length 






Welding 

the following consumables are recommended by AS1554.1-1985 

when welding sections. 

Manual metal-arc (MMAW) e41XX, e48XX 

Gas metal-arc (MiG) (GMAW) W50X 

gAlVAnising 

Manufactured and tested to meet the requirements of the following 

specification: 

AS1650-1989 Galvanised coatings 

Min. coating Mass: 300g/m 2 

coating Adherence: Adherence satisfactory when bent to radius 

8 x diameter of pipe. 

typicAl ApplicAtions 

Fire Sprinkler Systems 

Handrails 

Scaffolding 

traffic Signs 



SteeL pipeS to AS1074 

trAdelink steel pipes codes 

June 2010 

NomiNAl 

piN. Size 

blAcK HeAVy 

AS1074 

plAiN 6.5m 

blAcK HeAVy 

6.5m ASio74 

bSp mAle 

oNe eND 

blAcK HeAVy 

ASio74 

bSp mAle 6.5m 

gAlV HeAVy 

ASio74 

bSp mAle 6.5m 

blAcK meDium 

ASio74 

plAiN 6.5m 

blAcK meDium 

6.5m ASio74 

bSp mAle 

oNe eND 

15 024212 024725 023275 024185 024175 

20 024213 024203 024726 023276 024186 024176 

25 024214 024204 024727 023277 024187 021477 

32 024215 024205 024728 023278 024188 024178 

40 024216 024206 024729 023279 024189 024179 

50 024217 024730 023280 024190 

65 024218 024731 023281 024191 

80 024219 024732 023282 024192 

100 024220 024733 023283 024193 

125 024221 024734 023285 024194 

150 024222 024735 023284 024195 

200 

NomiNAl 

piN. Size 

blAcK meDium 

ASio74 

bSp mAle 6.5m 

gAlV meDium 

ASio74 

plAiN 6.5m 

gAlV meDium 

ASio74 

bSp mAle 6.5m 

gAlV meDium 

AS1074 

grooVeD eND 

6.5m 

blAcK ScH 40 

ANSi b36.10 

SeAmleSS* 

15 024473 023248 023260 024706 

20 024474 023249 023261 024707 

25 024475 023252 023262 024708 

32 024476 023250 023263 024709 

40 024477 023251 023264 024710 

50 024478 023253 023265 024722 

60 024479 023254 023266 024723 

80 024480 023256 023267 023408 024724 

100 024481 023257 023268 023410 024736 

125 024482 023258 023270 

150 024483 023259 023269 024737 

200 024738 

* butt-weld, per metre. 

As an approximate guide only, tubes to AS1074, when used for Steam Service, should be limited to the following Maximum pressures and 

temperatures. 

NomiNAl Size 

rANge 

mAx. preSSure iN kpa 

meDium & HeAVy 

mAx. temperAture 

iN DegreeS celciuS 

meDium & HeAVy Scr/JoiNtS WelD/JoiNtS meDium HeAVy 

DN 25 1206 1206 100°c 192°c 

DN 32 & 40 1034 1206 100°c 192°c 

DN 50, 65 & 80 861 1206 100°c 192°c 

DN 100 689 1206 100°c 192°c 

DN 150 *N.r. 1034 100°c 186°c 

*N.r. denotes Not recommended. 

tube & pipe Steel pipeS to AS1074 

15.9

tube & pipe Steel pipeS to ANSi b36.10 

15.10 

SteeL pipeS to ANSi b36.10 

steel pipes to Ansi b36.10 

NomiNAl 

Size 

DN NpS 

outSiDe 

DiAmeter 

mm 

Standard extra 

Strong 

6 1/8 10.3 1.73 2.41 

8 1/4 13.7 2.24 3.02 

10 3/8 17.1 2.31 3.20 

NomiNAl WAll tHicKNeSS for WelDeD & SeAmleSS Steel pipe ANSi b36.10 

All dimensions are shown in millimetres 

xx 

Strong 

Sched 

10 

Sched 

20 

15 1/2 21.3 2.77 3.73 7.47 4.78 

20 3/4 26.7 2.87 3.91 7.82 5.56 

25 1 33.4 3.38 4.55 9.09 6.35 

32 1¼ 42.2 3.56 4.85 9.70 6.35 

40 1½ 48.3 3.68 5.08 10.15 7.14 

50 2 60.3 3.91 5.54 11.07 8.74 

65 2½ 73.0 5.16 7.01 14.02 9.53 

80 3 88.9 5.49 7.62 15.24 11.13 

90 3½ 101.6 5.74 8.08 

100 4 114.3 6.02 8.56 17.12 11.13 13.49 

125 5 141.3 6.55 9.53 19.05 12.70 15.88 

150 6 168.3 7.11 10.97 21.95 14.72 18.26 

200 8 219.1 8.18 12.70 22.23 6.35 7.04 10.31 15.09 18.26 20.62 23.01 

250 10 273.1 9.27 12.70 25.40 6.35 7.80 XS 15.09 18.26 21.44 XXS 28.58 

300 12 323.9 9.53 12.70 25.40 6.35 8.38 10.31 14.27 17.48 21.44 XXS 28.58 33.32 

350 14 355.6 9.53 12.70 6.35 7.92 StdWt 11.13 15.09 19.05 23.83 27.79 31.75 35.71 

400 16 406.4 9.53 12.70 6.35 7.92 StdWt XS 16.66 21.44 26.19 30.96 36.53 40.49 

450 18 457 9.53 12.70 6.35 7.92 11.13 14.27 19.05 23.83 29.36 34.93 39.67 45.24 

500 20 508 9.53 12.70 6.35 StdWt XS 15.09 20.62 26.19 32.54 38.10 44.45 50.05 

550 22 559 9.53 12.70 6.35 StdWt XS - 22.23 28.58 34.93 41.28 47.63 53.98 

600 24 610 9.53 12.70 6.35 StdWt 14.27 17.48 24.61 30.96 38.89 46.02 52.37 59.54 

650 26 660 9.53 12.70 7.92 XS 

Sched 

30 

700 28 711 9.53 12.70 7.92 XS 15.88 

750 30 762 9.53 12.70 7.92 XS 15.88 

Sched 

40 

800 32 813 9.53 12.70 7.92 XS 15.88 17.48 

850 34 864 9.53 12.70 7.92 XS 15.88 17.48 

900 36 914 9.53 12.70 7.92 XS 15.88 19.05 

1050 42 1067 9.53 12.70 

product description 

Welded and seamless carbon steel pipes are generally available from 

8mm to 600mm nominal diameter. 

AlloWAble Working pressures 

For more information regarding allowable working pressures please 

refer to ASMe code for pressure piping b31. 

typicAl ApplicAtions 

American standard pipes are suitable for a wide range of 

applications from mining industry through to the petroleum and 

chemical processing industries. 

→ 

SAMe AS StANDArD Wt (Std. Wt) 

→ 

Sched 

60 

Sched 

80 

Sched 

100 

Sched 

120 

Sched 

140 

specificAtion 

seamless pipe Api 5L, 5LX 

AStM A53, A106, A120, A333, A335 

electric-resistance Welded (e.r.W.) 

Api 5L, 5LX 

AStM A53, A120, A135, A252, A333, A500 

uoe double submerged Arc Welded pipe 

Api 5L, 5LX & 5Lu 

AStM A53 

butt-Weld pipe Api 5L GrADe A25 

AStM A120 

AStM A53 GrADe F 

Sched 

160 


notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products. 

→ 

SAMe AS eXtrA StroNG Wt (XS) 

→

StAiNLeSS SteeL pipe 

product rAnge 

Stainless Steel pipe can be supplied on a standard lead time of 6 to 8 weeks ex-Mill in the austenitic grades tp304L, tp316 and tp316L. 

other grades available on request. 

tAble 1 - ApplicAtions & properties Austenitic 

size rAnge 

tAble 2 - schedule pipe - to Astm A312 

ScHeDule 

June 2010 

grADe ApplicAtioNS propertieS 

cpD Stainless 304 brewing and dairy equipment, evaporators, 

heat exchangers, hospital equipment and 

refrigerator parts. 

cpD Stainless 304l chemical plant food processing equipment, 

and for use in coal and petroleum industry. 

cpD Stainless 316 exterior applications subject to severe 

industrial or marine atmospheres; chemical, 

textile, photographic and papermaking 

equipment. 

cpD Stainless 316l chemical plant and food processing 

equipment. 

the table below shows the typical size range available. other sizes up to 3½” ScHeDuLe 10 may be available. please enquire. 

Standard length is nominally 6.1 metres although other lengths can be made available to suit the customer needs. 

NomiNAl bore 

inch mm oD 

DimeNSioNS 

Wt 

mASS 

kg/m 

tHeoreticAl 

burStiNg preSSure 

At AmbieNt temperAture 

mpa (pSi) 

Sch 10 ½ 15 21.34 2.11 1.00 102.2 (14825) 

¾ 20 26.67 2.11 1.28 81.7 (11850) 

1 25 33.40 2.77 2.09 85.8 (12450) 

1¼ 32 42.16 2.77 2.73 67.9 (9850) 

1½ 40 48.26 2.77 3.11 59.3 (8600) 

2 50 60.33 2.77 3.93 47.4 (6875) 

2½ 65 73.03 3.05 5.33 43.1 (6250) 

3 80 88.90 3.05 6.45 35.5 (5150) 

3½ 90 101.60 3.05 7.51 31.0 (4500) 

Sch 40 ½ 15 21.34 2.77 1.27 134.3 (19475) 

1 25 33.40 3.38 2.50 104.6 (15175) 

1¼ 32 42.16 3.56 3.43 87.2 (12650) 

1½ 40 48.26 3.68 4.05 78.9 (11450) 

2 50 60.33 3.91 5.44 67.2 (9750) 

* Safe working pressure is determined after allowing a suitable factor 

of safety based on type of line fluctuation. other Schedules available on 

request eg. Schedule 5. 

Suitable for use in certain equipment which operates under corrosive conditions. 

the low carbon content reduces the chance of intergranular corrosion caused by 

carbide precipitation. 

An extra low carbon austenitic stainless steel, with corrosion resistance similar to 

cpD Stainless 304, but with greater resistance to intergranular corrosion.can be 

heated for appreciable periods of time above 500 degrees c without the need for 

subsequent solution heat treatment. recommended where high heat input methods 

are used and subsequent solution heat treatment cannot be performed. 

More resistant to certain corrosive conditions than the standard non-molybdenum 

bearing austenitic stainless steels. Suitable where protection is required from 

highly corrosive non-oxidising acids. is used for plant and equipment in chemical 

manufacture. 

An extra low carbon modification for cpD Stainless 316, with similar corrosion 

resistance. intended for fabrication where welding without subsequent heat 

treatment is required. can be welded in heavy sections without the of intergranular 

corrosion (weld decay). Suitable for polishing to a bright finish as required for 

pharmaceutical and food processing equipment. 

liNe preSSure fluctuAtioN fActor of SAfety 

Non present 5 

Small & regular 8 

prolonged & excessive 12 

tube & pipe StAiNleSS Steel pipe 

15.11

tube & pipe StAiNleSS Steel pipe 

15.12 

StAiNLeSS SteeL pipe 

tolerAnces 

Wall thickness will be a minimum of nominal less 12.5%. 

outside diameter up to 1½” Nb +0.4mm 

-0.8mm 

over 1½ +0.8mm 

-0.8mm 

mArking 

All pipe will be marked in accordance with AStM A312 showing 

manufacturer, heat number, size, grade and condition. 

cHemicAl ANAlySiS % 

quAlity AssurAnce 

All pipe will be manufactured to AStM A312, ensuring that strict 

manufacturing processes are followed. 

Welding will be carried out using an automatic tiG welding process, 

with the weld area containing no filler metal and so ensuring the 

weld is at least as strong as the parent metal. 

finish 

the pipe will be annealed in a controlled, slightly reduced 

atmosphere. because of this, the pipe will retain the lustre and 

smooth surface typical of a 2b finish. this will enable you to easily 

differentiate the genuine Australian made product, as imported pipe 

usually has a rougher white pickled finish. other finishes are available 

on request. 

typicAl propertieS 304 304l 316 316l 

carbon 0.08max 0.035max 0.08max 0.035max 

chrome 18-20 18-20 16-18 16-18 

Nickel 8-11 8-13 10-14 10-15 

Molybdenum 2-3 2-3 

pHySicAl propertieS 

1390 1390 1370 1370 

Melting range °c 1450 1450 1400 1400 

Density kg/m 2 /mm 8.03 8.03 8.03 8.03 

Specific Heat (0-100°kJ/kg.K) 0.50 0.50 0.50 0.50 

thermal conductivity 500°c (W/m.K) 21.5 21.5 21.0 21.0 

Mean coefficient of thermal expansion 10.6/K (0-100°c) 17.3 17.3 16.0 16.0 

Modulus of elasticity (Gpa) 20 20 20 20 

tHermAl treAtmeNt °c 

Max. intermittent } Scaling temp in Air 840 870 870 870 

Max. continuous 900 930 930 930 

Annealing range 980- 980- 980- 870- 

(After Fabrication) 1070 1070 1070 1050 

mecHANicAl propertieS 

(AmbieNt temperAture) 

Yield Strength (Mpa) - min 205 170 205 170 

ultimate Strength (Mpa) - min 515 485 515 485 

% elogation (50mm) (longitudinal) - min 35 35 35 35 

Hardness Hrb 90max 90max 90max 90max 

* other Grades may be available on enquiry. 

trAdelink industriAl blutcher stAinless steel pipe codes 

Size 110mm 

leNgtH x 0.25m x 0.5m x 1.0m x 1.5m x 2.0m 

grade 304 024751 024752 024753 024754 024755 

grade 316 024742 024743 024744 024745 024746 

Subsequent annealing in a controlled atmosphere ensures properties 

of the weld and of the parent metal are similar. All pipe will be 

subject to mechanical and hydrostatic testing to ensure that all 

requirements of AStM A312 are met. 



StAiNLeSS SteeL tube 

Welded tube 

round welded tube is available in various grades, sizes, conditions 

and finishes as detailed below: 

grAdes 

Stainless steel tube can be supplied in the austenitic range, typically 

301, 304, 304L, 316, 316L and 321 as well as the ferritic range, 

typically 409 and 444. titanium and high nickel alloy tube can also be 

produced. 

sizes 

the table opposite shows the typical size range. other sizes may be 

available - please enquire. 

tube conditions 

the welding techniques employed result in tube with welds of at 

least equal strength to that of the parent material. by eliminating the 

use of filler wire, uniform chemical composition is maintained. 

the normal characteristics of stainless steel, high strength to weight 

ratio, good ductility and excellent corrosion resistance can be further 

improved by bright annealing, cold working of the weld and cold 

drawing. 

As Welded (AW) 

As welded tube receives no further treatment after forming and 

welding, it is used where limited manipulation is to be carried out. it 

has a smooth matt finish. 

As Welded Annealed (AWA) 

bright annealing after welding increases corrosion resistance and 

softens the tube for severe manipulation such as bending, expanding 

and forming. 

cold Worked (cW) and cold Worked Annealed (cWA) 

tube is available in cold worked (cW) and cold worked annealed 

(cWA) condition. in both conditions the weld area is subject to a 

mechanical forging process for grain refinement. cWA tube is then 

bright annealed, an economical alternative to fully welded drawn 

tube. 

Welded drawn (Wd) and Welded drawn Annealed (WdA). 

by cold drawing tube in AWA or cWA conditions, fine dimensional 

tolerances are achieved, having excellent uniformity of wall thickness 

and concentricity, uniform grain structure and hardness. For 

maximum corrosion resistance this tube is supplied in the annealed 

(WDA) condition. 

seamless (s) 

Stocks of seamless hollows can be obtained for re-drawing as 

required. 

June 2010 

testing 

electrical non-destructive testing is carried out on all welded tube 

products. 

finishes 

the natural metallic lustre of stainless steel, which remains during its 

extremely prolonged lifespan, can be further enhanced by polishing 

and buffing. this applies particularly in applications for decorative 

purposes. A number of polished finishes are available. 

mill finish (mf) 

An off the mill finish: roll forming marks are retained and an 

indication of the weld may be visible. 

buff polish (bp) 

A pleasing bright finish with medium lustre. traces of external 

weldline and roll marks can be visible. 

surfline polish (s/l) 

A bright and reflective finish, just short of a mirror polish which may 

have traces of weldline markings. 

gentube 

Similar to surfline polish but confined mainly to small diameter light 

wall tube. 

grit polish (gp) 

produced by centreless belt polishing to the grit size specified by 

the customer, i.e. 60, 120, 180, 240, 320, 400. there are no roll or 

weldline markings. 

satin polish (sp) 

Standard grit finish produced by polishing with 120 - 150 grit 

abrasive, and matches No. 4 finish. on square or rectangular tube the 

polishing pattern runs longitudinally. 

internal polish (ip) 

internally grit polished tube in lengths of up to 6 metres for diameters 

of 38.1 to 101.6mm is available. 

seAmless tube 

round seamless tube is produced typically within the range of 6.4 

mm to 76 mm outside diameter in 0.9 mm to 5.0 mm wall thickness. 

tube & pipe StAiNleSS Steel tube 

15.13


15.14 


tolerAnces 

off Weld mill 

outside diameter and wall thickness (measured 50mm from ends of 

tube). 

outside diameter tolerance Wall thickness 

up to 25.4 ±0.10 ±10% 

25.4 to 38.1 ±0.15 ±10% of 

over 38.1 to under 50.8 ±0.20 ±10% Norm 

50.8 to under 63.5 ±0.25 ±10% Wt 

63.5 to under 76.2 ±0.30 ±10% 

76.2 to 101.6 

ovality 

±0.38 ±10% 

Within tolerance field of outside diameters as shown above. 

tolerance on length 

up to and including 12m length +25mm – 0mm. 

closer tolerances available subject to negotiation. 

trAdelink industriAl stAinless steel tube 

straightness 

unless otherwise specified the tube shall have a straightness of 1 in 

500. 

Welded drawn tube 

unless otherwise specified, welded drawn tube is manufactured to 

the dimensional tolerances of AStM A249. 

random lengths 

Normal orders (unless otherwise specified) will be supplied as 

random lengths e.g. 95% will be 6m lengths remainder any length 

under 6m with a minimum length of 4m. 

Weight conversion formulas 

Austenitic: (Dia. – Wt.) X Wt. X 0.02468 

Ferritic: (Dia. –.Wt.).X.Wt. X.0.02425 

Size 6.35 12.70 15.88 19.05 22.23 25.04 31.75 

316 AWA Annealed 1.6mm mtr 034972 034973 

304 AWp polished 1.6mm mtr 025906 025907 025908 025909 025910 025911 

316 AWp polished 1.6mm mtr 025890 025891 025892 025893 025894 025895 

304 food Spec cWp 1.6mm mtr 025500 

316 food Spec cWp 1.6mm mtr 025530 

316 Spiral AW 1.6mm mtr 

Size 38.10 50.80 63.50 76.20 101.60 152.40 

316 AWA Annealed 1.6mm mtr 034974 

304 AWp polished 1.6mm mtr 025912 025913 025914 025915 025916 

316 AWp polished 1.6mm mtr 025896 025897 025898 025899 025900 

304 food Spec cWp 1.6mm mtr 025522 025524 025526 025528 025529 

316 food Spec cWp 1.6mm mtr 025531 025532 025534 025536 025538 

316 Spiral AW 1.6mm mtr 034971 




round Welded tube - typicAl size rAnge 

NomiNAl WAll tHicKNeSS 

NomiNAl outSiDe 

DiAmeter 

June 2010 

mm ins 

mm 0.5 0.6 0.7 0.9 1.2 1.6 2.0 2.6 3.2 

ins .020 .024 .028 .036 .048 .064 .080 .104 .128 

Swg 25 23 22 20 18 16 14 12 10 

tube 

coNDitioN 

AVAilAble 

9.53 3 /8 AW 

12.70 1 /2 AWA 

15.88 

5 /8 

19.05 3 /4 X X 

22.23 7 /8 X X 

25.40 1 X X 

31.75 1 1 /4 X X 

34.93 1 3 /8 AW 

38.10 1 1 /2 X X AWA 

41.28 1 5 /8 cW 

44.45 1 3 /4 cWA 

47.63 1 7 /8 

50.80 2 X X 

63.50 2 1 /2 

76.20 3 

88.90 3 1 /2 

101.60 4 

X 

preffered 304 and 316 grade sizes in regular production. 

Standard production range. 


15.15


15.16 


Astm specificAtions 

A269 

A268 

A554 

A270 

A249 

A688 

A312 

A789 

A213 

b338 

AStm SpecificAtioNS ApplicAtioN feAtureS AND coNDitioNS 

Seamless and welded austenitic stainless For general corrosion resistance and low or Average wall dimensions. AWA. cWA. S* 

steel tubing for general service 

high temperature service 

Seamless and welded ferritic stainless steel For general corrosion resistance and high Average wall dimesnions. AWA. cWA. S* 

tubing for general service 

temperature service 

Welded stainless steel mechanical tubing For mechanical applications where 

round, square, rectangular or special 

appearance, mechanical properties or shapes, austenitic or ferritic alloys, polished, 

corrosion resistance is needed 

if specified. AW. AWA. cW. cWA 

Seamless and welded austenitic stainless For use in food and dairy industry tYpe 304 only, average wall dimensions. 

steel sanitary tubing 

AWA. S* (surface finish to be specified) 

Welded austenitic steel boiler, superheater, 

heat exchanger and condenser tubes 

For superheaters and heat exchangers Average wall dimensions. cWA. WDA 

Welded austenitic stainless steel feedwater For feedwater heater tubes including those Average wall dimensions 15.9 to 25.4mm 

heater tubes 

bent, if specified, into the form of u-tubes o.D. range. cWA. WDA. 

Seamless and welded austenitic stainless For general and high temperature service Nominal bore pipe sizes and schedule 

steel pipe 

number, or o.D. and average wall thickness. 

AWA. cWA. WDA. S* 

Seamless and welded ferritic and austenitic For general service with particular emphasis Average wall dimensions. AWA. cWA. S* 

alloy steel boiler, superheater and heat 

exchanger tube 

on resistance to stress corrosion cracking 

Seamless ferritic and austenitic alloy steel 

boiler, superheater and heat exchanger tube 

boilers, superheaters, heat exchangers Minimum wall thickness dimensions. S* 

Seamless and welded titanium and titanium For use in surface evaporators and heat 

alloy tubes for condensers and heat 

exchanges 

exchangers 

S* Seamless tube or pipe. 

AStM and ASMe tube users may find reference to some of the above specification numbers prefixed by an ‘S’ e.g. ‘SA249’. the presence of the ‘S’ means that 

the specification is an ASMe specification similar to (but not always the same as) the AStM specification of the same number. AStM - American Society for 

testing & Materials ASMe - American Society of Mechanical engineers. Lysaght tube can be produced to either specification. 



upVc preSSure pipe 

trAdelink industriAl upVc pressure pipe codes 

June 2010 

NomiNAl 

DiAmeter 

(mm) 

Size 

ppSo upVc pressure pipe solvent 

weld joint to AS 1477-1988 

pVc pipe 

clASS 4.5 

SolVeNt 

WelD AS1477 

6m StrAigHt 

pVc pipe 

clASS 6 

SolVeNt 

WelD AS1477 

6m StrAigHt 

pVc pipe 

clASS 9 

SolVeNt 

WelD AS1477 

6m StrAigHt 

pVc pipe 

clASS 12 

SolVeNt 

WelD AS1477 

6m StrAigHt 

pVc pipe 

clASS 15 

SolVeNt 

WelD AS1477 

6m StrAigHt 

pVc pipe 

clASS 18 

SolVeNt 

WelD AS1477 

6m StrAigHt 

15 011713 011723 

20 011703 011714 011724 

25 011694 011704 011715 011725 

32 011695 011705 011716 011726 

40 011686 011796 011706 011717 011727 

50 011687 011697 011707 011718 011728 

65 011688 011698 011708 011719 011729 

80 011680 011689 011699 011709 011730 

100 011681 011690 011700 011710 011721 011731 

125 011684 011702 

150 011682 011691 011701 011711 011732 

May be available in cut metre lengths. May be available in rubber ring joint instead of solvent weld. 

unplasticised polyvinyl chloride (upVc) pressure pipe and fittings are 

provided with solvent weld and bSp threaded joints; typical upVc 

applications include potable water supply and distribution; industrial 

process water systems; irrigation systems; Sewer rising mains and 

discharge lines. 

NomiNAl 

DiAmeter 

(mm) 

15 15 18 

20 12 15 18 

preSSure clASS 

25 9 12 15 18 

32 9 12 15 18 

40 6 9 12 15 18 

50 6 9 12 15 18 

65 4.5 6 9 12 15 18 

80 4.5 6 9 12 15 18 

100 4.5 6 9 12 15 18 

125 4.5 6 9 12 

150 4.5 6 9 12 15 18 

195 (8”) 4.5 6 9 12 

225 4.5 6 9 12 

tube & pipe upVc preSSure pipe 

15.17

tube & pipe permApipe 

15.18 

perMApipe 

pre-insulAted piping systems 

offers flexibility in inner pipe to outer casing combinations to virtually 

produce any insulation thickness required. (When ordering please 

specify inner pipe and outer casing size). 

the heart of pre-insulated piping is without a doubt the integrity 

of the polyurethane ie. minimum density requirements and positive 

displacement of any possible air pockets within the insulation. 

the process involves the injection of the polyurethane using the "one 

shot" method. this method has proven to be extremely consistent. 

insulation on both permapipe Above Ground AG and under Ground 

uG systems is a machine injected MDi (Methylene Di-isocynate) 

based rigid polyurethane foam. 

properties 

Density 70 kg/m3 K Value 0.023 W/m 0K 

Water permeability 1-4 perm/in 

compressive Strength 70-90 psi 

AboVe ground system 

permapipe AG utilises a choice of outer casing material. the 

standard being 0.6mm thick Galvabond spirally lockseamed into a 

tube of required diameter. 

Also available are: • Powder coated Galv. 

• BHP Colourbond 

• Stainless Steel 

* For these specials, minimum runs apply. 

outer case diameters start at 75mm and increase in 25mm 

increments up to 500mm. 

reinstAtement of Joints Ag system 

Achieved by installing a sheetmetal sleeve around straights joints 

(or a ‘lobster back’ casing around elbows and a sheetmetal ‘tee’ 

piece around tees). these have a pouring hole and two 3mm holes 

for air release cut in the casing. the correct amount of polyurethane 

two pack is mixed and poured into the pouring hole. When foaming 

approaches the pouring hole this is sealed with tape. When the 

cavity is completely filled the foam will extrude from the air holes. 

the pouring hole is covered with a sheetmetal disc and pop rivets are 

inserted in the air holes. 

under ground system 

permapipe uG utilises an outer casing manufactured from HDpe it is 

uV stabilised to prevent degradation in direct sunlight. 

the casing used is substantially thicker than similar imported 

products. this ensures that possible physical damage due to 

transport, installation of back-filling is reduced considerably. 

outer casing sizes available (mm): 

90 110 140 200 225 250 280 315 355 400 

reinstAtement of Joints ug system 

Achieved by the same method as the AG system with the addition 

of a heat-shrinkable polythene/bitumen wraparound on the straight 

joints. the bends and tees utilise a primer on sheetmetal, and a vinyl 

backed bitumen tape wrapover to exclude possible moisture entry.

TUBE & PIPE - Tradelink

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?