22-inch Variable Speed Drill Press - JET Tools

More documents

Recommendations

Info

Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for the JET Model J-2210 and J-2230 Drill Presses. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web site: www.wmhtoolgroup.com. Specifications Model:.....................................................................J-2210 ......................... J-2230-2 ......................J-2230-4 Stock Number .......................................................354205 ............................354206 ........................ 354207 Motor ...................................................... 2HP, 1Ph, 230V ..............2HP, 3Ph, 230V .......... 2HP, 3Ph, 460V Drilling Capacity (in.) Cast Iron............................................................1-1/4 ............................... 1-1/4 ............................1-1/4 Steel ..................................................................1-1/8 ............................... 1-1/8 ............................1-1/8 Column Diameter (in.) .............................................4-5/16 ............................. 4-5/16 ..........................4-5/16 Maximum Dimension Spindle to Column (in.)...............11 ....................................11 ................................ 11 Spindle Taper........................................................... MT-3 ............................... MT-3 ............................MT-3 Spindle Travel (in.) ..........................................................5 ......................................5 .................................. 5 Spindle Dimension to Base (in.)..............................46-1/2 ............................. 46-1/2 ..........................46-1/2 Spindle Dimension to Table (in.).............................32-3/4 ............................. 32-3/4 ..........................32-3/4 Table Size (in.) ..........................................16-1/8 x 19-1/4 ............... 16-1/8 x 19-1/4 ............16-1/8 x 19-1/4 Number of T-slots.............................. 2 in table, 2 in base ........ 2 in table, 2 in base .....2 in table, 2 in base Spindle Speed Range (RPM) ............60-450 & 240-1800 ...........60-450 & 120-900 ....... 60-450 & 120-900 ....................................................................................N/A .......120-900 & 240-1800 ... 120-900 & 240-1800 Overall Height (in.) ........................................................73 ....................................73 ................................ 73 Base Size (in.)...........................................19-3/8 x 29-1/4 ............... 19-3/8 x 29-1/4 ............19-3/8 x 29-1/4 Table Travel (in.) .....................................................26-1/2 ............................. 26-1/2 ..........................26-1/2 Net Weight – approximate (lbs.) .................................660 ..................................660 .............................. 660 Shipping Weight – approximate (lbs.) .........................790 ..................................790 .............................. 790 The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, WMH Tool Group reserves the right to change specifications at any time and without prior notice, without incurring obligations. 6
Features and Terminology Figure 1 7
Page 1 and 2: Operating Instructions and Parts Ma
Page 3 and 4: Table of Contents Table of Contents
Page 5: 21. Check damaged parts. Before fur
Page 9 and 10: A power plug is not provided with t
Page 11 and 12: Be sure to remove drift key from sp
Page 13 and 14: Drilling Recommendations Speeds for
Page 15 and 16: Replacement Parts Replacement parts
Page 17 and 18: 57 .............2210-257...........
Page 19 and 20: Parts List: Headstock Cover Assembl
Page 21 and 22: Parts List: Base and Column Assembl
Page 23 and 24: Electrical Connections - 3 Phase, 2

22-inch Variable Speed Drill Press - JET Tools

Create successful ePaper yourself

Delete template?

Save as template?