1 - Erich Schmid Institute

More documents

Recommendations

Info

$dissertation global and local fracture properties of metal matrix ...$

This work was financially supported by the Austrian Science Fund (FWF) through project AP26043501. Copyright ©2008 by Stefan Massl. All rights reserved. Erich Schmid Institute of Materials Science Austrian Academy of Sciences Jahnstrasse 12 A-8700 Leoben http://www.oeaw.ac.at/esi This doctoral thesis was typeset by the use of KOMA-Script and L ATEX 2ε. The template was modified by Dr. Weinhandl and Dr. Vorhauer.
To my family
Page 1: University of Leoben Dissertation I
Page 7 and 8: Acknowledgements I would like to th
Page 9 and 10: Abstract A method for the determina
Page 11 and 12: Non quia difficilia sunt non audemu
Page 13 and 14: Contents Affidavit V Acknowledgemen
Page 15 and 16: Contents E Mechanics of Residually
Page 17 and 18: 1.1 Why Coatings? 1 Introduction Su
Page 19 and 20: 1.2 Fabrication Processes of Thin F
Page 21 and 22: components are discussed subsequent
Page 23 and 24: 1.3.3 Friction and Wear 1.3 Origin
Page 25 and 26: 1.4 Methods for Film Stress Measure
Page 31 and 32: 1.5 Fracture Mechanics of Thin Film
Page 33 and 34: Cantilever Beam Deflection Method 1
Page 35 and 36: 1.5 Fracture Mechanics of Thin Film
Page 37 and 38: Bibliography [1] Freund LB, Suresh
Page 39 and 40: Aim of the Dissertation The aim of
Page 41 and 42: Summary The main task of this disse
Page 43 and 44: involved, the incident angle, the i
Page 45 and 46: a new method that allows the straig
Page 47 and 48: 2 List of appended papers Paper A S
Page 49 and 50: A A Direct Method of Determining Co
Page 51 and 52: A.3 Experimental 840nm PVD-deposite
Page 53 and 54:
A.4 Calculation Procedure and Resul
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
A.5 Remarks on the Determined Stres
Page 63 and 64:
A.5 Remarks on the Determined Stres
Page 65 and 66:
A.6 Discussion of Possible Sources
Page 67 and 68:
Bibliography to paper A [1] Eiper E
Page 69 and 70:
B Stress Measurement in Thin Films
Page 71 and 72:
B.2 Brief Description of the ILR Me
Page 73 and 74:
B.3 Discussion of Sources of Error
Page 75 and 76:
B.3.3 Accuracy of SEM Measurements
Page 77 and 78:
B.4 Experimental Design to Minimize
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
B.5 Determination of Young’s Modu
Page 85 and 86:
[1] Massl S, Keckes J, Pippan R, Ac
Page 87 and 88:
C A New Cantilever Technique Reveal
Page 89 and 90:
C.2 Experimental curved, which assu
Page 91 and 92:
C.2 Experimental of residual stress
Page 93 and 94:
C.3 Discussion and Concluding Remar
Page 95 and 96:
[1] Nix WD. Metall Trans A 1989;20A
Page 97 and 98:
D Investigation of Fracture Propert
Page 99 and 100:
D.2 Experimental the bias voltage w
Page 101 and 102:
D.2 Experimental Table D.1: The com
Page 103 and 104:
D.3 Results Figure D.5: SEM picture
Page 105 and 106:
D.4 Discussion Table D.3: Deflectio
Page 107 and 108:
D.4 Discussion strength with. Kamiy
Page 109 and 110:
D.5 Conclusion stresses, which disa
Page 111 and 112:
Bibliography to paper D [1] Weppelm
Page 113 and 114:
Bibliography to paper D [44] Ziegle
Page 115 and 116:
E Mechanics of Residually Stressed
Page 117 and 118:
E.2 Sign Convention Figure E.1: Ini
Page 119 and 120:
E.4 Calculation of the Normal Stres
Page 121 and 122:
E.5 Determination of the Position o
Page 123 and 124:
E.6 Moment Balance Figure E.5: Forc
Page 125 and 126:
E.8 Correlation of the Stresses in
Page 127 and 128:
E.9 An Example: Depth Profile of Re
show all

1 - Erich Schmid Institute

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?