Installation instructions for splashback - Fisher & Paykel

fisherpaykel.com

Installation instructions for splashback - Fisher & Paykel

Installation instructions

Splashback

SB60X3, SB90X3 & SB120X 3 models NZ AU UK IE EU ROW

Important!

SAVE THESE INSTRUCTIONS

The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and

specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

1 SAFETY AND WARNINGS

4 SPLASHBACK DIMENSIONS

D

B

WARNING!

Cut hazard

Splashback dimensions (mm)

Take care – panel edges are sharp.

Failure to use caution could result in injury or cuts.

Please make this information available to the person responsible

for installing this product as soon as possible. It could help to

reduce your installation costs.

Depending on the wall surface, it may be necessary to use masonry

or hollow wall anchors when fixing the screws. In all instances,

do ensure that a secure fixing is obtained.

Read the instructions before installing the product.

Important!

■■ Be careful of sharp edges when handling this product.

■■ Before drilling holes, check that the wall is clear of any cables or

pipes, etc.

■■ Fixing to a solid stud is recommended. If fixing to plasterboard, use

an appropriate fixing method.

■■ The stainless steel surface can be easily damaged during installation

if knocked or grazed by tools. Please take care to protect the surface

when installing the Splashback.

■■ Protect the cooktop surface in front with cardboard, or the like, to

prevent damage occurring whilst installing the Splashback behind.

E

A

Diagram 1

SB60X3 SB90X3 SB120X3

A width 600 900 1200

B height 750 750 750

C depth 10 10 10

C

2 GETTING STARTED

Tools required (not included)

■■ Electric drill

■■ Phillipshead screwdriver

Before starting

■■ Unpack your Splashback and check for any marks or signs of transit

damage before installing.

3 PARTS SUPPLIED

5 FIX MOUNTING BRACKETS

Fix the four hanging/mounting brackets into position using one screw

fixed into the middle slot.

450mm

240mm

42mm

Mounting

screws (x 12)

D

Diagram 2

Mounting bracket specifications (mm)

Mounting

brackets (x 4)

Splashback (x 1)

SB60X3 SB90X3 SB120X3

D width apart 500 800 1100


6 ALIGN & HANG USING THE FOUR

SLOTS ON THE BACK WITH THE FOUR

MOUNTING BRACKETS

Wall

Splashback

Mounting

bracket

Diagram 3

7 ENSURE THE SPLASHBACK

IS LEVEL.

Ensure the Wall Splashback is hung level and square. If not, remove the

Splashback from the mounting brackets and loosen the mounting

screws Splashback to adjust the position.

Repeat steps 5 to 7 until Splashback is levelled and square.

Cooking bench

Diagram 4

9 REHANG THE SPLASHBACK.

8 SECURE THE MOUNTING

BRACKETS.

When the Splashback is levelled and square, remove the Splashback

from the mounting brackets again.

Use the remaining screws to secure the mounting brackets on both

sides of the middle slot.

Diagram 5

Before you call for service or assistance…

Check the things you can do yourself. Refer to the installation instructions, your User Guide – in particular the troubleshooting section and check that:

1 your product is correctly installed.

2 you are familiar with its normal operation.

If after checking these points you still need assistance or parts, use the link at www.fisherpaykel.com/locator/servicer/ for regional service providers.

590361A NZ AU UK IE EU ROW 08.11

More magazines by this user
Similar magazines