The System Manual of SOL-20 - History of Computers

More documents

Recommendations

Info

III. TAPE COMMANDS (cont.) Tape Commands in Detail Get a file from tape GET (name(/unit) (addr)) This command transfers the specified or next tape file into memory. If a (name/unit) is given, this command will search forward on the cassette until that file is found. The (addr) parameter, if given, specifies the memory location at which the file will be loaded. If the addr is omitted, the file will be loaded as specified in the header. Example: Result: GET TARGT/2 Gets the program WARM from tape unit #2 into memory as specified by the tape file header information. Returns to SOLOS command mode. Get, then Execute XEQ (name(/unit) (addr)) This command is an extension of the GET command which gets a tape file and executes as specified by the header information. The (/unit) and (addr) are optional and operate the same as with the GET command. Example: Result: Save a file XEQ FOCAL Gets, then executes, a program named "FOCAL" from tape unit 1. SAVE name (/unit) addr1 addr2 (addr3) This command transfers program or data onto a tape cassette file name (name) starting at (addr1) and ending at (addr2). The name of the file becomes part of the tape's header information. SET TYPE and SET XEQ commands affect the header information on the tape file. The optional addr3 specifies the address (if different than addr1) to be entered in the tape header. Example: SAVE CHASE/2 0 1FF Result: Saves onto tape unit 2 a program named "CHASE" starting at location 0000 and ending at location 1FF. Catalog of files CAT (/unit) This command will start the tape unit specified and list each tape file header information. Example: CAT /2 Result: SLOPE 0500 0200 HUM 0500 0B00 7
III. TAPE COMMANDS (cont.) Note: A very useful feature of the CAT command is to apply power to the tape units when needed to rewind tape. Depressing the MODE (or Control-@) key will remove power from tape unit and return to COMMAND mode. 8
Page 1 and 2:
Sol SYSTEMS MANUAL, 6200 Hollis Str
Page 3 and 4:
CONTENTS OUTILNE Detailed contents
Page 5 and 6:
Sol TERMINAL COMPUTERTM FIGURE 7-5
Page 7 and 8:
PROCESSOR TECHNOLOGY CORPORATION So
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
PROCESSOR TECHNOLOGY CORPORATION TM
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
PROCESSOR TECHNOLOGY CORPORATION Sa
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
PROCESSOR TECHNOLOGY CORPORATION Sa
Page 86 and 87:
Page 88:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
VIII THEORY OF OPERATION 8.1 INTROD
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155: PROCESSOR TECHNOLOGY CORPORATION So
Page 187 and 188: SECTION IX SOFTWARE Sol TERMINAL CO
Page 192 and 193: M0100 SOLOS (tm) /CUTER (tm) USER'S
Page 194 and 195: P R E F A C E This manual describes
Page 196: TABLE OF CONTENTS (cont.) IV. SET C
Page 199 and 200: INTRODUCTION (cont.) Only the first
Page 201 and 202: II. CONSOLE COMMANDS Console Comman
Page 203: III. TAPE COMMANDS Tape commands ar
Page 207 and 208: V. SET COMMANDS (cont.) The Output
Page 209 and 210: V. SET COMMANDS (cont.) The Custom
Page 211 and 212: V. SUBROUTINES A. Introduction to t
Page 213 and 214: V. SUBROUTINES (cont.) JUMP TABLE A
Page 215 and 216: V. SUBROUTINES (cont.) AOUT entry p
Page 217 and 218: V. SUBROUTINES (cont.) When calling
Page 219 and 220: V. SUBROUTINES (cont.) SOLOS provid
Page 221 and 222: VI. LOADING & EXECUTING CUTER (Appl
show all

The System Manual of SOL-20 - History of Computers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?