European Technical Approval Technical Approval ETA 12 ... - Hempel

More documents

Recommendations

Info

Page 4 of 46 of ETA 12/0581, issued on 17.01.2013 The environmental use categories are specified in ETAG 018 Part 2, section 2.2.2: • Type X: external use • Type Y: internal use and semi-exposed conditions • Type Z 1 : internal use with high humidity conditions • Type Z 2 :internal use 1.3 Assumed working life The provisions made in this European Technical Approval (ETA) are based on an assumed working life of the reactive coatings for fire protection HEMPACORE ONE 43600 and HEMPACORE ONE FD 43601 of at least 10 years, provided that the conditions laid down in sections 4.2, 5.1 and 5.2 for the packaging, transport, storage and installation as well as appropriate use, maintenance and repair are met. The indications given on the working life cannot be interpreted as a guarantee given by the manufacturer or the Approval Body, but should only be regarded as a means for choosing the appropriate products in relation to the expected economically reasonable working life of the works. 2 Characteristics of products and methods of verification The assessment of the fitness of HEMPACORE ONE 43600 and HEMPACORE ONE FD 43601 for the intended use considering the essential requirements was performed following the Guideline for European Technical Approval 018 for Fire Protective Products Part 1: General and Part 2: Reactive coatings for fire protection of steel elements. 2.1 Mechanical resistance and stability (ER 1) Not relevant. 2.2 Safety in case of fire (ER 2) 2.2.1 Reaction to fire The reactive coating systems including all the primers and topcoats listed in Table 1 have a performance determined for a reaction to fire Class D-s2,d0 according to EN 13501-1 7 . 2.2.2 Fire resistance The product has been tested according to EN 13381-8 8 . Fire resistance classes have been defined according to EN 13501-2 and are presented in Annex 1. 2.2.3 Smouldering fire exposure The verification under exposure to the smouldering fire curve according to EN 13381-8, Annex A, has been carried out and the product meets the requirements established in EN 13381-8. 2.3 Hygiene, health and the environment (ER 3) 2.3.1 Release of dangerous substances According to the manufacturer’s declaration, the product specification has been compared with the regulated dangerous substances listed on the database established on the EC construction website, with Annex XVII and Annex XIV of REACH and with the ECHA Candidate List of Substances of Very High Concern to verify that they do not contain such substances above the acceptable limits. In addition to the specific clauses relating to dangerous substances contained in this European Technical Approval, there may be other requirements applicable to the products falling within its 7 EN 13501-1:2007 Fire classification of construction products and building elements. Part 1: Classification using data from reaction to fire tests implemented. 8 EN 13381-8:2010 Test methods for determining the contribution to the fire resistance of structural members. Part 8: Applied reactive protection to steel members.
Page 5 of 46 of ETA 12/0581, issued on 17.01.2013 scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction Products Directive, these requirements need also to be complied with, when and where they apply. 2.4 Safety in use (ER 4) Not relevant. 2.5 Protection against noise (ER 5) Not relevant. 2.6 Energy economy and heat retention (ER 6) Not relevant. 2.7 Aspects of durability, serviceability and identification of the products 2.7.1 Durability and serviceability The primers and topcoats indicated in section 1.2.2 of this ETA are compatible with the reactive coatings. The verifications were made in accordance with ETAG 018, Part 2, section 5.7.2.2. The approved environmental use categories shall be taken from section 1.2.2 of this ETA. 2.7.2 Identification of products The ETA is issued for the system on the basis of agreed data/information, deposited with the Catalonia Institute of Construction Technology which identifies the system components that have been assessed and judged. Identification tests according to ETAG 018 Part 2, section 5.7.3, have been carried out on components, which confirm that the system under assessment conforms to its declared characteristics. 3 Evaluation and attestation of conformity and CE marking 3.1 System of attestation of conformity According to the decision 1999/454/EC 9 of the European Commission, system 1 of attestation of conformity applies. This system of attestation of conformity is defined as follows: System 1: Certification of the conformity of the product by a notified certification body on the basis of: (a) Tasks for the manufacturer: (1) Factory production control (2) Further testing of samples taken at the factory by the manufacturer in accordance with a prescribed test plan (b) Tasks for the approved body: (3) Initial type testing of the product (4) Initial inspection of the factory and of factory production control (5) Continuous surveillance, assessment and approval of factory production control Note: Approved bodies are also referred to as “notified bodies”. 3.2 Responsibilities 3.2.1 Tasks of the manufacturer 3.2.1.1 Factory production control The manufacturer shall exercise permanent internal control of production. All the elements, requirements and provisions adopted by the manufacturer shall be documented in a systematic manner in the form of written policies and procedures, including records of results performed in 9 Official Journal of the European Communities Nº L178, 14.7.1999, p. 52
Page 1 and 2: The Catalonia Institute of Construc
Page 3: Page 3 of 46 of ETA 12/0581, issued
Page 7 and 8: Page 7 of 46 of ETA 12/0581, issued
Page 9 and 10: Page 9 of 46 of ETA 12/0581, issued
Page 11 and 12: Page 11 of 46 of ETA 12/0581, issue

European Technical Approval Technical Approval ETA 12 ... - Hempel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?