Destratification Fan - Hydor

Destratification Fan
Ceiling Mounted Heat Recovery Units

e-Strati
Destratification Fan
Ceiling Mounted Heat Recovery Units
With Hydor Destratification fans installed in the
ceiling space, the accumulated warm
air is redistributed down towards the
floor level and re-circulated around the building
to sustain even temperatures and
reduce run time of heaters.
Heat rises within buildings from floor level and collects in the
ceiling void, even in well ventilated buildings the difference in
temperature levels can be as much as 5°C or more.
(See diagram below)
Heaters are required to operate more frequently in this
situation to restore temperatures at floor height to
acceptable levels for the staff. This results in higher fuel costs
and wasted energy.
The redistribution of warm air creates a more even
temperature around the unit and allows floor temperature
to be sustained for longer periods without prolonged and
frequent use of heaters, thereby reducing energy expenditure
significantly.
Tests have also proven that the fans aid maintenance of a
constant temperature at floor level, when compared to a unit
reliant solely on heaters, recordings showed considerable
fluctuations in temperature.
Hydor Ceiling Mounted Destratification Units are suitable
for any building where, due to their design, heat is gathered
in the ceiling area. Warehouses, factories, storage units,
garden centres or any enclosed area where heaters are used
to obtain a comfortable working environment for the public
and staff alike.
HOT AIR
BEFORE
COOL AIR
HOT AIR
AFTER
WARM AIR
22º C
19º C
16º C
14º C
13º C
11º C
22º C
21º C
20º C
19º C
18º C
17º C
Tel: +44 (0) 1725 511422
Fax: +44 (0) 1725 512637
Email: info@hydor.co.uk
Visit: www.hydor.co.uk
Unit 8, Parkers Close,
Downton Business Centre,
Downton, Salisbury,
Wiltshire, SP5 3RB
In association with
A member of

Features & Benefits
• Improved heat distribution and
reduced energy bills.
• Available in two sizes; 500mm
for the smaller buildings and
630mm for larger units.
• High efficiency fan easily
accessible for cleaning and
maintenance.
• The advanced performance
impeller produces up to
2.2m³/sec.
• Highly efficient motors are
matched to the aerodynamic
performance of the impeller
for maximum efficiency.
• Suspension eyelets fitted as
standard for easy installation.
• Fitted with motor-side
guard for safety.
• The outlet louvres are
adjustable allowing the air to
be directed at varying angles
to suit the requirement.
(*See diagram below)
• The louvres set in four
directions enable 360° cover.
• Anodised egg-crate grille can
be fitted as an alternative.
(Please state at time of ordering)
Dimensional Data
C
B
Product
Code
A B C
HIDSF500 655 295 60
HIDSF630 805 325 60
N.B. All Dimensions are expressed in millimetres
A SQUARE
Performance & Electrical Data
Product
Code
Airflow
m³/s
Speed
(r/min)
Power
Watts
FL
Amps
Start
Amps
Weight
Kg
HIDSF500 1.80 1300 420 1.65 5.9 27
HIDSF630 2.20 940 460 2.30 6.0 42
Units are available in three phase if required
Hydor Ltd, due to a policy of continuous development and improvement reserve the right to supply products
which may differ from those illustrated and described in this publication. Certified data will be supplied on request.
Tel: +44 (0) 1725 511422
Fax: +44 (0) 1725 512637
Email: info@hydor.co.uk
Visit: www.hydor.co.uk
Unit 8, Parkers Close,
Downton Business Centre,
Downton, Salisbury,
Wiltshire, SP5 3RB
In association with
A member of