Views
4 years ago

User Manual - Visionary Forces

User Manual - Visionary Forces

User Manual - Visionary

  • Page 2 and 3: TABLE OF CONTENTS TABLE OF CONTENTS
  • Page 4 and 5: DISCLAIMER RED ® has made every ef
  • Page 6 and 7: AUSTRALIA AND NEW ZEALAND STATEMENT
  • Page 8 and 9: BEFORE YOU START Congratulations on
  • Page 10 and 11: CAUTION: The power cord plug for th
  • Page 12 and 13: This recording technique permits RG
  • Page 14 and 15: LINE LEVEL ANALOG INPUTS The record
  • Page 16 and 17: REDMOTE ® REDMOTE is a camera cont
  • Page 18 and 19: Where: A = camera A, 001 = reel 001
  • Page 20 and 21: CAMERA OPERATIONAL CONTROLS This se
  • Page 22 and 23: SSD Slot: Slot for REDMAG 1.8” SS
  • Page 24 and 25: FRONT A A Stills / Movie Slider Sid
  • Page 26 and 27: Navigation Group: Allows navigation
  • Page 28 and 29: To remove the side handle: 1. Power
  • Page 30 and 31: DUAL BATTERY MODULE The DUAL BATT
  • Page 32 and 33: 5. Tighten the screws again in a cr
  • Page 34 and 35: 2. Rotate module down flush with th
  • Page 36 and 37: Default settings for User Function
  • Page 38 and 39: TOUCHSCREEN LCD Red offers a five i
  • Page 40 and 41: QUAD BATTERY MODULE The optional QU
  • Page 42 and 43: AC POWER ADAPTOR - (DSMC) AC POWER
  • Page 44 and 45: POWER UP Locate the camera’s Powe
  • Page 46 and 47: GRAPHICAL USER INTERFACE AND NAVIGA
  • Page 48 and 49: The GUI is broken down into the fol
  • Page 50 and 51: GEN GEN Gray - No genlock signal
  • Page 52 and 53:

    SIDE HANDLE As you navigate and adj

  • Page 54 and 55:

    USING TOUCHSCREEN LCD If operating

  • Page 56 and 57:

    POWER DOWN NOTE: Camera will automa

  • Page 58 and 59:

    FIRST TIME USE - SETTING UP YOUR RE

  • Page 60 and 61:

    RED BRICK Attach to the camera usin

  • Page 62 and 63:

    PERFORM A BLACK SHADING CALIBRATION

  • Page 64 and 65:

    CAMERA ID (SLATE) If operating on a

  • Page 66 and 67:

    MENU CONTROLS Displayed in the Uppe

  • Page 68 and 69:

    MAIN MENU Available options under t

  • Page 70 and 71:

    ISO (SENSITIVITY) Adjusts the camer

  • Page 72 and 73:

    FOCUS Provides the ability to enter

  • Page 74 and 75:

    INTEGRATION TIME Provides the abili

  • Page 76 and 77:

    ADVANCED SETTINGS When selected, al

  • Page 78 and 79:

    RESOLUTION Allows adjustment of res

  • Page 80 and 81:

    HDR ON / OFF By default, HDRx is OF

  • Page 82 and 83:

    Performance of Auto Focus may be re

  • Page 84 and 85:

    DSMC CANON MOUNT ELECTRONICALLY SUP

  • Page 86 and 87:

    SPOT Provides a small, square targe

  • Page 88 and 89:

    LENS INFORMATION DISPLAY RED DSMC T

  • Page 90 and 91:

    Select Create and enter a name for

  • Page 92 and 93:

    COPY PRESETS FROM CAMERA TO SSD U

  • Page 94 and 95:

    MEDIA MENU The Media Menu is used t

  • Page 96 and 97:

    UTILITIES Options are SECURE FORMAT

  • Page 98 and 99:

    EXPOSURE This will show areas of un

  • Page 100 and 101:

    ORANGE Super White (IRE 105-107) RE

  • Page 102 and 103:

    RAW RAW displays the image without

  • Page 104 and 105:

    Low IRE Change the desired setting

  • Page 106 and 107:

    MODES Available GUI display mode ad

  • Page 108 and 109:

    SIZE Available options are Off, Ful

  • Page 110 and 111:

    CONTRAST Adjusts the overall contra

  • Page 112 and 113:

    COLOR/GAMMA The COLOR/GAMMA sub-men

  • Page 114 and 115:

    TIME CODE DISPLAY Allows you to cho

  • Page 116 and 117:

    AUDIO/VIDEO Menu adjusts AUDIO INPU

  • Page 118 and 119:

    AUDIO OUTPUT Allows adjustment of a

  • Page 120 and 121:

    Limiter Enables signal limiter circ

  • Page 122 and 123:

    TEST SIGNALS Permits the video moni

  • Page 124 and 125:

    OPTIONS Select the desired option

  • Page 126 and 127:

    DATE / TIME This menu allows the us

  • Page 128 and 129:

    NETWORK If the Gigabit Ethernet por

  • Page 130 and 131:

    GPIO GPIO selects the GPIO preferen

  • Page 132 and 133:

    SYNC MODE Allows the shutter timing

  • Page 134 and 135:

    INDICATORS Beep Speaker Available o

  • Page 136 and 137:

    CALIBRATION Sensor calibration is a

  • Page 138 and 139:

    BLACK SHADING PROCEDURE The calibra

  • Page 140 and 141:

    ENABLE / DISABLE SENSOR TEST PATTER

  • Page 142 and 143:

    When selected, you will be asked to

  • Page 144 and 145:

    PLAYBACK Playback allows you to vie

  • Page 146 and 147:

    PRESETS Allows you to apply presets

  • Page 148 and 149:

    SETTINGS Available options are DISP

  • Page 150 and 151:

    CLIP PLAYBACK STATUS BAR Displays t

  • Page 152 and 153:

    IN / OUT POINT MARKER Allows you to

  • Page 154 and 155:

    SHUTDOWN Power OFF controls are int

  • Page 156 and 157:

    APPENDIX B: MANAGING DIGITAL MEDIA

  • Page 158 and 159:

    MEDIA CAPACITY REMAINING STATUS The

  • Page 160 and 161:

    ERASING MEDIA NOTE: If the media wa

  • Page 162 and 163:

    MIC-1, MIC-2 (MICROPHONE AUDIO) Two

  • Page 164 and 165:

    HD-SDI A standard 75 Ohm BNC connec

  • Page 166 and 167:

    The Video Genlock input may be used

  • Page 168 and 169:

    CTRL (RS232 CONTROL) A 4-pin LEMO c

  • Page 170 and 171:

    DC IN (POWER INPUT) The 6-pin LEMO

  • Page 172 and 173:

    SIDE SSD MODULE REAR B FRONT A A B

  • Page 174 and 175:

    APPENDIX D: DEFAULT KEY FUNCTIONS C

  • Page 176 and 177:

    APPENDIX E: REDMOTE OPERATION CONTR

  • Page 178 and 179:

    C A B REDMOTE Navigation Group A Sc

  • Page 180 and 181:

    Note: For illustration only: rear s

  • Page 182 and 183:

    RECORDING To record, press the Red

  • Page 184 and 185:

    ADVANCED OPERATION: REDMOTE MENUS S

  • Page 186 and 187:

    Note: Once this procedure has occur

  • Page 188 and 189:

    OPERATING WITH MULTIPLE CAMERAS FRO

  • Page 190 and 191:

    6. Select “Setup Slot” and pres

  • Page 192 and 193:

    MAINTENANCE INTERNAL BATTERY CHARGE

  • Page 194 and 195:

    UPGRADING REDMOTE FIRMWARE The REDM

  • Page 196 and 197:

    7. Click “Connect”. When REDMOT

  • Page 198 and 199:

    12. Once the File Transfer Status i

  • Page 200 and 201:

    5. Select “I Agree” to the lice

  • Page 202 and 203:

    10. The program will now install. A

  • Page 204 and 205:

    9. The selected file is shown in th

  • Page 206 and 207:

    16. Select “Disconnect” on the

  • Page 208 and 209:

    SLAVE CAMERA Perform the following

  • Page 210 and 211:

    Green BNC connector is for Tri-Leve

  • Page 212 and 213:

    ISO 800 - False Color: Exposure Sel

  • Page 214 and 215:

    ISO 800 - False Color: Exposure Sel

  • Page 216 and 217:

    APPROPRIATE EXPOSURE ISO 800 - Moni

  • Page 218 and 219:

    ISO 800 - False Color: Video Select

  • Page 220 and 221:

    ISO 100 - No Exposure Adjustment In

  • Page 222 and 223:

    REDCINE-X ® PRO REDCINE-X PRO is a

  • Page 224 and 225:

    DO NOT USE any other solvents, chem

  • Page 226 and 227:

    4. Power up the camera. 5. Power up

  • Page 228 and 229:

    APPENDIX J: TROUBLESHOOTING NO MEDI

  • Page 230 and 231:

    CAMERA BRAIN DIMENSIONS Front View

  • Page 232 and 233:

    Top View Bottom View 955-0002_v3.2,

  • Page 234 and 235:

    APPENDIX L: RESOLUTION CHART 955-00

  • Page 236 and 237:

    MAIN MENU DEFAULT VALUES ARE DISPLA

  • Page 238 and 239:

    SECONDARY MENUS PRESS MENU ICON (LC

  • Page 240:

    SECONDARY MENUS PRESS MENU ICON (LC

DVCPRO50 Digital Video Cassette Recorder ... - Visionary Forces
CLIPSTER® & DCI Mastering - Visionary Forces
Digital Rapids DRC PCI Card Installation - Visionary Forces
Visionary Simply Smart - Small Dog Electronics
User Manual Supplement - Hasselblad
User's Manual - Directory listing for
SCX-6220 Users Guide & Owners Operation Manual - OlsonBros