Hyper 10sc Electric RTR - Ofna

Electronic Speed Control
(INCLUDED)
Brush 15Turn
Motor (INCLUDED)

LED Edition
2.4G DSSS Technology
3-Channel 2.4G Radio Control System
INSTRUCTION MANUAL
• Before using, read this manual carefully
AUX Channel
Steering Trim
Steering Wheel
TRIM LED
Power Switch
Charging Jack
Bind Switch
Throttle Trim
St. Dual Rate
Throttle Trigger
Battery Box
CAUTION
• To use your Radio with your models correctly and safely, read this manual carefully and keep it in a
safe place for future reference.
Warning:
1. This product is only equipped for radio controlled cars;
2. The usage of this product should be approved by local law or regulations;
3. We will not be responsible for the damages caused by unauthorized modification, adjustment
or replacement of parts on this product;
4. The manual may be altered without prior notice. Please contact us if you have any corrections
or clarifications that should be made in the manual;
• Before turning on the transmitter, make sure the transmitter batteries are fresh. The voltage of the
transmitter batteries is never lower than 9.6V, and please check and confirm that the servos are
all well and properly connected.
• Keep the radio system away from moist, high temperature and strong vibrations. Do not clean radio
with any solvent.
• Make sure antenna does not touch anything when power switch is turned on. Do not leave this radio
in reach of small children.
• Please use this product according to your local laws and regulations, we are not responsible for any
incidents or damages.

Steering Dual Rates Setup
LEFT MID RIGHT
ST.TRIM
TH.TRIM
INC
DEC
ST.DR
NOR
REV
POWER ST.DR ST. TH.
ST.D/R SW
•DEFINITION:
Steering Dual Rate (ST. DR): Is the adjustment that allows the dual rate value (maximum
servo travel) to be increased (INC) or decreased(DEC) with in a range of 0% to 100%
of the steering servo. This functions very useful in a race conditions as it allows you to
tailor the steering radius and sensitivity for the current track conditions.
•ADJUSTMENT:
1.Press and hold the “INC” (Increase) button until the LED on the “ST.DR” turn solid
indicating the maximum turning radius or value of 100%.
2.Press and hold the “DEC” (Decrease) button until the LED on the ‘ST.DR” goes dim or out
to reach the minimum turning radius or value 0%.
CHECKING YOUR DUAL RATE
•To Check Your Dual Rate: First turn your radio “ON” then turn “ON” your
vehicle. Check your steering on your radio by turning left and right several
times. Now turn your steering wheel all the way to the left or right whichever
you choose and hold it their while pushing the “DEC” (decrease) button on
the “ST-DR” and hold it down, you should see that the wheel on your vehicle
decrease in radius and that the LED on “ST-DR” will start blinking and slowly
dim. Now to increase the dual rate turn the wheel left or right all the way and
hold it while pushing the “INC” button this will increase the radius of the wheel
and the LED on ST-DR will start blinking slowly and turning solid indicating
that the “Dual Rate” is at 100% . When running your vehicle try to run the
“Dual Rate” at maximum radius (100%). Then if you have too much steering
then decease as needed.
100%
0%
100%
100%
0% 0%
100%
100%
100%
POWER
ST.DR
INC
DEC
ST.D/R

2.4Ghz Binding
•Press and hold the bind button on the front of the transmitter while
turning ON the power switch button until the (ST.DR) LED Flashes.
Flashing LED
2. With the system hooked up as shown, insert the binding cable in
the charging plug receptacle. Turn on the power of the receiver
(4.8 - 5.6V), and now the LED should be flashing indicating
that the receiver is ready to bind.
Plug In
STEP 2 Power Switch (turn on)
Binding cable
Solid LED
Receiver
3. The LED should go solid, indicating the system
has connected. Now turn off the receiver and
remove the binding cable.
STEP 1
Bind (Press and hold)
Binding cable
Receiver
AUX Channel Function (CH3)
•This switch control the transmitter’s third channel. A servo plugged in this Channel 3 will move to full travel in one direction when
the switch is in the “AUX” position, then move the switch to the “OFF” position the servo will move in the opposite position . This
channel can be use to turn on all sort of things in your vehicle. For example, lights, on board camera etc..... l
Handling Procedure For Batteries
•Battery Replacement
1) Remove the battery cover from the transmitter by sliding it in the direction of the arrow.
2) Remove the used batteries.
3) Load the new 8 AA size alkaline, or Nickel Metal Hydride (NimH) rechargeable batteries,
and pay very close attention to the polarity marking on the batteries.
4) Slide the battery cover back onto the case.
5) If you use rechargeable batteries OFNA make this charger 10210 it will charge your Transmitter
9.6v at 100mA and Receiver battery 4.8v-6v at 100mA at the same time.
NOTICE THE DIRECTION OF BATTERY COVER
•Caution
Always make sure you reinsert the batteries are in the correct polarity order. If the batteries are loaded
incorrectly, the transmitter may not work or can be damaged.
When the transmitter is not used for a long period of time remember to remove the batteries. If the batteries
do happen to leak, clean the batteries case and contacts thoroughly and make sure the contacts are free of
corrosion.
•Battery Disposal
Some countries and state require special handling of used batteries, please contact the agencies responsible
for recycling hazardous wastes in your local area.
•Battery low voltage alarm indicator. LED Power light will flash.
Receiver Connection Diagram
10210 - DUAL CHARGER, 4.8V-6V/9.6V TRANSMITTER AND RECEIVER
(Not included)
Specification Data
•Transmitter
Channels: 3
Frequency: 2.4Ghz
Power DC: 9.6V - 12V
Measurement: 280 x 190 x 85mm
(Packing Meas.)
Net Weight: 510g
•Receiver
Channels: 3
Frequency: 2.4Ghz
Power DC: 4.8 - 5.6V
Net Weight: 13.5g

Warranty Period
OFNA warranties that the Products purchased (the “Products”) will be free from defects in materials and workmanship at the
date of purchase by the Purchaser.
Limited Warranty
(1) This warranty is limited to the original Purchaser (”Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS
PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers
only those Products purchased from and authorized OFNA dealer. Third party transactions are not covered by this
warranty. Proof of purchase is required for warranty claims. Further, OFNA reserves the right to change or modify this
warranty without notice and disclaims all other warranties, express or implied.
(2) Limitations - OFNA MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
(3) Purchaser Remedy - OFNA sole obligation hereunder shall be that OFNA will, at its option, (1) repair or (2) replace, any
Product determined by OFNA to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies.
OFNA reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions
are at the sole discretion of OFNA. This warranty does not cover cosmetic damage or damage due to acts of God,
accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does
not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than OFNA.
Return of any goods by Purchaser must be approved by OFNA before shipment.
Damage Limits
OFNA SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM
IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in an event shall the liability of
OFNA exceed the individual price of the Product on which liability is asserted. As OFNA has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act
of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised
to return this Product immediately in new and unused condition to the place of purchase.
Safety Precautions
This is a sophisticated hobby Product and not a toy, It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury of damage to
the Product or other property. This Product is not intended for use by children without direct adult supervision. The Product
manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and
warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.
FOR ADDITIONAL HELP YOU CAN CALL OFNA TECH SUPPORT AT (949)586-2910 OR
GO TO WWW.OFNA.COM/GUIDE.HTML FOR HOW TO VIDEO

TO: OFNA TECHNICAL SUPPORT
7 VANDERBILT, IRVINE, CA 92618
TODAY’S DATE: month________day______
1. Print out form.
2. Fill out the form completely.
3. Make a copy of purchase receipt. All replacements/repairs will not be processed,
unless accompanied by proof that item(s) was purchased.
4. Call OFNA technical support at (949)586-2910 for assistance.
1. Your name
____________________________
2. Your address:
____________________________
____________________________
3. Your Phone Number
(_____)______________________
4. Your e-mail address:
____________________________
5. Summary of your problem (check lines):
a______part(s) is missing from my kit
b______part(s) seems to be defective
c______other problem
6. Name of kit / part (on tag or end of box)
_____________________________
7. Kit/part number (on tag or end of box)
_____________________________
8. Purchased from (store name)
_____________________________
a. Store phone: (_____) _________
b. _____Item was a gift?
9. If a part is missing form the kit, circle
the appropriate answers:
a. Yes / No: Is kit box damaged?
b. Yes / No: Factory Seal sticker was secure.
c. Yes / No: I am the original owner.
d. Yes / No: I have contacted the dealer first.
10. Describe your issue fully and include any part numbers:
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
____________________________________________________________
Failure to fill out this form completely will cause a delay in processing!
11. Affix proof of purchase on second page. All replacement / repairs will not be processed
unless accompanied by proof that item(s) was purchased.
Can’t find Proof of Purchase?
A. If you lost the store receipt, ask the store if they will give you a new one.
B. We do not accepted the following as a substitute: Hand written receipts, ebay transaction numbers/forms or
credit card statements.
12. Send in form with your defective product, as instructed to do by the Ofna
technician,(Name)_________________ you spoke to. Ph:(949)586-2910 Fax: (949)583-9272

B4218 ESC Instruction and Specification
WARNING ELECTRIC MOTOR AND ESC ARE EXTREMELY HOT AFTER
RUNNING, CAN CAUSE SERIOUS INJURY, HANDLE WITH CARE
•Special Features:
1. Exclusive feature for this model. Auto set to neutral position on the throttle. No programming
or adjustment is required. Just one second after powering on the system, the speed control
will beep indicating that is has auto set to the neutral position ( while the speed control is
setting the neutral position do not touch the throttle trigger, leave it at neutral ).
Fig.1 Fig.2 Fig.3
FORWARD
NEUTRAL
2. Thermal Protection Function of The ESC B4218. If the speed control over heats, the Thermal
Protection function will be activated. Once the “TP” is activated, the throttle will rapidly turn
on and off and acceleration becomes erratic. Stop driving immediately, do not drive the car
until the Speed Controller cools down.
3. LED indication, two colors Green/Red
4. Large sturdy aluminum heatsink for maximum heat dispersing.
•Specification:
1. Input Voltage: 6~8.4V 6-7cell Nimh or 2cell Lipo
2. Power IC 150A at (77F), 100A at (212F)
3. Supported motor >12T - 27T Mabuchi Motor
4. Factory default Spec: Output Continuous/Peak Current 70A/120A(10sec)
5. Over temperature protection at 200F.
6. BEC Voltage 5V at 1Amp
7. FET internal: forward/reverse...........0.0025/0.005 ohm
8. Size:36 x 35 x 30.5mm
9. Weight......53.7g/1.89oz
BATTERY
BRAKE
AND
REVERSE
BLUE NEG
ORG. POS.
•Throttle Neutral and ESC setting:
1. Switch on the transmitter.
TH.TRIM
2. Set the throttle trim to the middle or the green LED on your Transmitter “TH”
3. Switch on the power of the ESC
4. The ESC will sound 3 beeps (DO RE MI) confirmation, indicating the ESC
is ready & the throttle is at neutral position.
•Operating Instructions:
1. Connect the ESC wires to the motor. (Blue is neg and Orange is Positive See Fig. 5)
2. Plug the receiver wire into the throttle or #2 channel on the receiver
3. Ventilation - Mount the ESC in a location that has good ventilation & isolate it from vibration
and shock. Ventilation is extremely important for cooling the ESC & Motor.
4. Plug in your battery, before turning on the ESC, make sure your transmitter is on & the throttle
trigger is at the neutral position. (See Fig 2)
5. Turn on your ESC, the LED light on the ESC will flash red then goes to solid green and a tone
will sound indicating that the ESC is set and ready to go.
FIG. 4
SWITCH
RECEIVER WIRE
FOR ADDITIONAL HELP YOU CAN CALL OFNA TECH SUPPORT AT (949)586-2910 OR
GO TO WWW.OFNA.COM/GUIDE.HTML FOR HOW TO VIDEO
FIG. 5

11066
21003
21006
11066
21003
21003
21004
21003
21003
21004
21003
21001
11066
21004
94046
5000wt FRONT DIFF
1000wt REAR DIFF.
11066
11066
21003
21038
21003
21003
21004
21003
21003
21004
11066
21003
94046
5000wt
21037

94034
21005
11065
21005
21002
21002
21007
21007
11065
21015
94002
21014
21014
22012
21015
21016
36870
21012

11066
11066
21017
18075
21017
18075
21017
94043
21028
21029
21029
94043
21028
21009
21009
21029
94043
21123
94004
21029
21029
21123 94004

21121
94005
21121
94005
94002
21124
94003
94002
94003
21018
21018
21018
94005
21018 94005

94003
94004
94004
94041 21154
94041
94003
21153
94003
94034
94033
94034
94033
94033
21018
21018

21028
21029
21011
21029
21028
21033
94041
21078
21033
94041
21078
21078
21033
21034
21078
21033
21033
21033
94033
21033
21033
21033
21033

94002
21127
21036
21036
21023
21023
94005

94004
94004
94019
21128
94019
21026
11066
21025
36870
21017
11066
18075
18075
21017
36870
94041
21059
21027
21059
21029
94004
21029
21123
21123
21028
21024

21029
94043
21021
21021
21124
21122
19031
19031
94038
94003
94002
94004
21122
94041

21022
21023
21023 21022
94005
21018
21018
94005
21018
21018

94033
94034
21018 21018
94002
21127
94003
21126

94005
21143
21143
21143
21128
94041
21133
94019
94019
94019

Assembly of Center Differential Mount
21132
94003
Assembly of Side Guard
21129
94003
21039
94017
94019
21301
94017
94019

94040 21316 11T
(Not Included)
94040
94034
94002
21313
94002
(NOT INCLUDED)
21133

21302
94021
94021
21307
21304
94019
94019

21049
94017
94017
21303
94017
94002
94017 94002
(Not Included)

29076
28081
29076

21130
94008
94003
94002
94008
94002
94003
21036
21048
21048
21036

21228
21138
21138
21228
21044
21228
21228
21138
21067
21228
21067
21144
21066
21067
Shock springs set of 4
21139 Blue Med
21155 White Hard
21139 Blue Med
21155 White Hard

19031
94005
94038
94005
21135
21134

10985
10985
10985
10985
21136

1 4 6 1 6 H YP E R 1 0 S C R T R P AR T S L I S T
OFNA DESCRIPTIONS RETAIL OFNA DESCRIPTIONS RETAIL
11064 BEARING 5x8, 4PCS. 11.95 21131 CENTER DRIVE SHAFT ALUM SC 22.95
11065 BEARING 5x11, 6PCS. 17.95 21132 CENTER DIFF MOUNT ALUM SC 7.95
11066 BEARING 10x15, 4PCS. 15.95 21133 CHASSIS HYPER 10 SC 44.95
11210 SINK ALUM. WASHER 3mm, 16PCS. 7.95 21134 WHEEL, HYPER 10 SC PAIR 8.95
18075 BEARING, 6x13mm. 4PCS. 15.95 21135 TIRES, HYPER 10SC PAIR 19.95
19018 BOOT,SHOCK SHAFT,SILICONE 4PCS 8.95 21136 BODY, CLEAR HYPER 10SC 39.95
19031 BALL,STEEL,SHOCKS 4PCS. 7.95 21137 DECAL HYPER 10 SC BODY 14.95
21001 GEAR, CROWN HYPER 10SC 24.95 21138 SHOCK SHAFT HYPER 10SC 4PCS 12.95
21002 GEAR, PINION HYPER 10SC 12.95 21139 SHOCK SPRING BLUE SET 10SC 15.95
21003 GEAR, DIFF HYPER 10SC 12.95 21140 SHOCK HYPER 10SC PAIR 44.95
21004 DIFF CASE W/GASKET HYPER 10SC 6.95 21141 SCREW SET HYPER 10SC 14.95
21005 DRIVE CUP CENTER HYPER 10SC 11.95 21143 SCREW,3X37mm & 3MM NUT H10SC 2.95
21006 DRIVE CUP F/R DIFF HYPER 10SC 12.95 21144 SHOCK BODY FR/RR HYPER 10SC 27.95
21007 GEARBOX CASE HYPER 10SC 8.95 21153 BUMPER, HYPER 10SC STOCK 6.95
21008 SHOCK MOUNT FR HYPER 10SC 6.95 21154 BUMPER, BRACE HYPER 10SC 6.95
21009 FRONT HINGE PIN HOLDER FR HYPER 10SC 5.95 21301 CNC ALUM MOTOR MOUNT HYPER M/E 34.95
21011 ARM, UPPER FRONT HYP. MINI 6.95 21302 CENTER DIFF UPPER PLATE HME 7.95
21012 ARM, LOWER FRONT HYPER 10SC 9.95 21303 ALUM RADIO TRAY HYPER MINI E 7.95
21014 STEERING KNUCKLES FRONT H.10SC 10.95 21304 BATTERY BOX HYPER MINI E 14.95
21015 PILLOW BALL HYPER 10SC 16.95 21307 VELCRO BATTERY STRAP HME 7.95
21016 CVA, FRONT HYPER 10SC 34.95 21308 SCREW SET HYPER MINI E 7.95
21017 HEX HUB HYPER 10SC 6.95 21316 PINION GEAR 11T-3MM STOCK 12.95
21018 ANTI ROLL BAR SET HYPER 10SC 9.95 22012 FLANGE BALL SET 12.95
21021 HINGE PIN HOLDER REAR H.10SC 5.95 22028 SHOCK REPAIR SET 8.95
21022 ARM, UPPER REAR HYPER 10SC 6.95 22086 SNAP PIN 3.95
21023 TURNBUCKLE, STEERING H. MINI 10.95 28081 ANT.TUBE 1pc.STR.M 4pcs,S 2pcs 2.95
21024 ARM, LOWER REAR 10.95 29076 ANT. MOUNT ALUM. HYPER 9 7.95
21025 UP-RIGHT REAR HYPER MINI 7.95 94041 NUT, 3MM NYLOK 4PCS 1.95
21026 AXLES REAR HYPER MINI 12.95
OPTION PARTS
21027 DOGBONES REAR HYPER MINI 12.95 19363 BALL STUD,SHOCK CNC ALUM, 4PCS 8.95
21028 HINGE PIN SET HYPER MINI 11.95 21155 SPRINGS WHITE HYPER 10SC HARD 15.95
21029 HINGE PIN BUSHING HYPER MINI 4.95 21156 SHOCK TOWER FR GRAPHITE H10SC 24.95
21032 WING POST MOUNT HYPER MINI 6.95 21157 SHOCK TOWER RR GRAPHITE H10SC 29.95
21033 SERVO SAVER SET HYPER MINI 19.95 21158 CENTER GRAPHITE PLATE H10SC 14.95
21034 SERVO SAVER ARM HYPER MINI 6.95 21159 SERVO GRAPHITE PLATE H10SC 9.95
21035 TURNBUCKLE REAR UPPER ARM H.M. 10.95 21160 CNC 7075 FRONT SHOCK TOWER SC 14.95
21036 TURNBUCKLE ENDS HYPER MINI 5.95 21161 CNC 7075 REAR SHOCK TOWER SC 14.95
21037 SPUR GEAR STEEL HYPER MINI 24.95 21162 CNC 7075 HINGE PIN PL FR/RR SC 8.95
21038 CENTER DIFF OUTPUT HYPER MINI 14.95 21163 CNC 7075 HINGE PIN HOLDER FR 8.95
21039 CENTER DIFF MOUNT HYPER MINI 10.95 21164 CNC 7075 REAR HING PIN HOLDER 8.95
21048 TURNBUCKLE STEERING SERVO H.M. 5.95 21165 CNC 7075 CHASSIS HYPER 10SC 54.95
21049 SERVO MOUNT & HORN SET H.M. 10.95 21197 WHEEL, HYPER 10SC WHITE 8.95
21059 HINGE PIN REAR 3x35mm H. MINI 2.95 21198 WHEEL, HYPER 10SC BLACK 8.95
21063 SHOCK BLADDER HYPER 10SC 6.95 21199 CVA DOGBONE ONLY HYPER 10SC 19.95
21066 SHOCK COLLAR THREADED H. MINI 12.95 21281 SHOCK PISTON OPTIONAL HYPER SC 7.95
21067 SHOCK PLASTIC PARTS HYPER MINI 7.95 21306 PINION GEAR 14T-3MM 12.95
21070 SHOCK, REAR SET HYPER MINI 45.95 21311 PINION GEAR 15T-3MM 12.95
21078 BUSHING, 5x8mm HYPER MINI 2.95 21312 PINION GEAR 16T-3MM 12.95
21079 SCREW SET HYPER MINI 19.95 21313 CNC MOTOR HEAT SINK HYPER M/E 19.95
21121 SHOCK TOWER FRONT ALUM SC 9.95 21314 PINION GEAR 12T-3M 12.95
21122 SHOCK TOWER REAR ALUM SC 11.95 21315 PINION GEAR 13T-3MM 12.95
21123 SUSPENSION PLATE F/R SC 6.95 29311 PINION 14T-5MM HYPER 9e 13.95
21124 BODY POST HYPER 10 SC 7.95 29325 PINION 15T-5MM HYPER 9e 13.95
21126 BUMPER, REAR SET SC 14.95 29326 PINION 16T-5MM HYPER 9e 13.95
21127 ARM HOLDER F/R AND BRACE SC 6.95 29328 PINION 17T-5MM HYPER 9E 13.95
21128 CHASSIS BRACE F/R SC 8.95 29329 PINION 18T-5MM HYPER 9E 13.95
21129 SIDE GUARD HYPER 10 SC 13.95 30669 PINION ADAPTOR 5MM TO 3MM 2PCS 8.95
21130 TOP BUMPER HANDLE SC 11.95 81096 FOAM,MOLDED DONUTS,OR/SOFT 6PC 7.95
81097 FOAM,MOLDED DONUTS,YL/MED. 6PC 7.95

21001
21121
21015
21026
21126
21002 21009
21016
21027
21016
21003 21123
21017
21028
21037
21133
21004 21011
21018
21029
21038
21129
21005 21012
21122
21124
21039
21130
21006 21127
21021
21143
21132
21007 21014
21022
21033
21048
21138
21154
21023
21034
21023
21063
21024
21035
21128
21144
21025
21036
21131
21066
21128

21049 21049
21079
21304
11066
21281
SHOCK PISTION
29076
11210
21313
21067
18075
21141
21155
White Hard
21139
Blue Med.
21307
10985
(STOCK)
21316
21140
21136
19018
21314
22086
21301
19031
21315
21134
21302
28081
21306
21135
21303
22012
21311
21308
22028
21312 21153
(STOCK)
21078
11065

OWNER’S REGISTRATION CARD
OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling
this kit will provide many hours of enjoyment.
The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.
In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your
dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer
location. Other items such as radio and engine other covered by individual warranties.
IMPORTANT!
Please print or type, filling in the information listed below and mail immediately
MAIL TO:
OFNA RACING
7 VANDERBILT
IRVINE, CA. 92618
TEL: (949) 586-2910
REGISTRATION CARD
Write in Your Model Name and Part Number
RACER’S NAME TEL:( )
ADDRESS
CITY STATE ZIP
DEALER’S NAME TEL: ( )
ADDRESS
CITY STATE ZIP
OFNA
7 Vanderbilt
Irvine, Ca. 92618