TAGnology_TAGid -125kHz_Protocol.pdf - RFID Webshop

More documents

Recommendations

Info

Communication Reader-Host Rev. 1.2 February 1999 3.7.13 HT1_Mutual_Authent Carries out the full authentication procedure between the transponder and the read/write device. After this mutual authentication you are allowed to edit areas which can only be accessed in Crypto Mode. Using -keyinfo- you can choose between Key/Logdata Set A and B. Use a Plain command (that is still encrypted), HFReset or GetSnr (resets the already selected transponder) to exit this mode. C-Function: void HT1_Mutual_Authent (BYTE_T keyinfo); Header-File: Hitag1.H Serial protocol: HOST - READ/WRITE DEVICE 0x03 'A' keyinfo BCC keyinfo: 0x00 ... Key/Logdata Set A 0x01 ... Key/Logdata Set B READ/WRITE DEVICE - HOST 0x02 Status BCC Status: 0 ... no error -1 ... SERIAL ERROR -7 ... AUTHENTICATION ERROR Protokoll HTRM801 V1.2/C Page 28 (107)
February 1999 Rev. 1.2 Communication Reader-Host 3.7.14 HTS_GetSnrReset This command provides the serial number of a HITAG 1 transponder and sets the transponder into Advanced <strong>Protocol</strong> Mode (command is not available for HITAG 1 transponders based on ASIC HT1 ICS30 01x ; only available for HITAG 1 transponders based on ASIC HT1 ICS30 02x). For further information on the Advanced <strong>Protocol</strong> Mode see chapter „Transponders“. C-Function: void HTS_GetSnrReset (BYTE mode, DWORD_T *snr, BYTE_T *more); Header-File: Hitag1.H Serial protocol: HOST - READ/WRITE DEVICE 0x03 'y' mode 0x45 READ/WRITE DEVICE - HOST 7 0 ------ 31 24 n+2 Status SNR-LSB ------ SNR-MSB more BCC n = 0 if an error occurred (error code in Status). n = 5 if data were read from a transponder (Status = 0). mode: bit0: 0…. without HF Reset 1…. with HF Reset bit2: 0…. Hitag standard protocoll 1…. Hitag advance protocoll bit4: 0…. Diffent Tranponder types expected 1…. HitagS Transponder expected more: Proximity Reader: more is always 0. Long Range Reader: more equal to one indicates that there is at least one additional transponder in the reading area of the read/write device. Status: 0 ... no error -1 ... SERIAL ERROR -3 ... NOTAG Page 29 (107) Protokoll HTRM801 V1.2/C
Page 1 and 2: TAGnology RFID GmbH | Grazer Vorsta
Page 3 and 4: February 1999 Rev. 1.2 Introduction
Page 9 and 10: February 1999 Rev. 1.2 Provided Hos
Page 11 and 12: February 1999 Rev. 1.2 Communicatio
Page 27: February 1999 Rev. 1.2 Communicatio
Page 79 and 80:
February 1999 Rev. 1.2 Communicatio
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
February 1999 Rev. 1.2 Transponders
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
February 1999 Rev. 1.2 Personalizat
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
February 1999 Rev. 1.2 Security Con
Page 107:
February 1999 Rev. 1.2 Security Con
show all

TAGnology_TAGid -125kHz_Protocol.pdf - RFID Webshop

Create successful ePaper yourself

Delete template?

Save as template?