Lionel Holiday Tradition Express Owner's Manual Lionel Holiday ...

71-1102-250
6/08
Rev. 1
Lionel
Holiday Tradition Express
Owner’s Manual
CAUTION– ELECTRICALLY OPERATED PRODUCT. NOT RECOMMENDED FOR CHILDREN UNDER EIGHT YEARS OF
AGE. AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING
AND USE TO PREVENT ELECTRIC SHOCK. TRANSFORMER RATING-INPUT: 120 VAC; 60 HZ, OUPTPU: 12 VOC; 30 VA

Congratulations!
Congratulations on your purchase of the Lionel Holiday Tradition Express Train Set. This
set features a musical 4-4-2 steam locomotive and tender, calliope car, and caboose. Read
this instruction manual thoroughly for important tips on operating and maintaining your ‘G’
Gauge set.
Holiday Tradition Express Set Inventory
• 4-4-2 musical steam locomotive with lights
• Tender with lights and animation
• Calliope car with lights and animation
• Caboose with lights and animation
• Twelve curved tracks
• Four straight tracks
• Lockon track power connector
• 12V AC wall transformer
Parents!
Locomotive
The transformer included with this set should be periodically examined for
conditions that may result in the risk of fire, electric shock or injury to persons
(such as damage to the output cord, blades, housing, or other parts). In the event
that such conditions exist, the transformer should not be used until properly
repaired.
• Elf on locomotive pilot
• Elf engineer
• Lighted wreath, holly, and Lionel logo
• Locomotive sounds, whistle, bell, Santa, and music
Tender
• Lighted holly
• Animated elf shovels coal
Calliope Car
• Three animated elves
• Fourteen animated pipes
• Lighted holly and panels
Caboose
• Lighted holly, wreath and windows
• Animated Elf stacks presents
• Animated Santa waves

Table of Contents
Creating your layout
Joining the track sections 4
Building your layout 5
Connecting power to the track 6
Placing the train on the track 7-8
Operating the train
Operating the train 9
Remote Controllerfunctions 10
Maintaining and servicing your set
Resolving short circuits 11
Cleaning the track 12
Replacing the lamp in the caboose 12
Maintenance and lubrication 13
Troubleshooting 14
Notes 15
Limited Warranty/Lionel Service 16
The following Lionel marks may be used throughout this instruction manual and are protected under law. All
rights reserved.
Lionel ® , TrainMaster ® , Odyssey ® , RailSounds ® , CrewTalk , TowerCom , DynaChuff , StationSounds ,
Pullmor ® , ElectroCoupler , Magne-Traction ® , CAB-1 ® Remote Controller, PowerMaster ® , Lionel
ZW ® , ZW ® , PowerHouse ® , TMCC ® , Lionelville, Lockon ® , Wireless Tether , LionMaster ® , FatBoy ,
American Flyer ® , TrainSounds , PowerMax , LEGACY , PowerMax Plus
The name FasTrack ® is used with permission from Pitsco, Inc.

Creating your layout
Joining the track sections
Join the track sections together by inserting the pins of each track section into the rail
opening of the other section. Refer to Figure 1. Pins must be fully inserted and track joints
tightly fitted for good electrical contact. The plastic track sections snap together to assure
correct assembly. If the rail openings have become enlarged and fit together loosely, pinch the
rail around a track pin with a pair of pliers. If any pins fall out of the track, be sure to replace
them.
The rails should be kept clean, dry, and free from oil and grease. Remove corrosion and
dirt spots with any commercial non abrasive metal polishing pad to keep your track in top
condition. Wipe the track with a clean soft cloth dampened with track cleaner from the Lionel
Lubrication and Maintenance Set (6-62927).
Figure 1. Track assembly
Pin

Creating your layout
Building your layout
You can make one of three layout configurations with the track provided. These layouts are
illustrated in Figure 2.
Basic Circle
Connect all 12 curved track sections to form a simple circle.
Extended Circle
Build a circle, but insert one straight section between every three curve sections. The extended
circle is like a square with rounded corners.
Oval
Divide the basic circle in half and connect the two half-circles with the straight sections. Use
one or two straight sections on each side.
Circle Extended circle Oval
Figure 2. Track layouts

Creating your layout
Connecting power to the track
After selecting your track layout, you are ready to connect power to your track. Power
connections are made on the new curved terminal track section, which is illustrated in
Figure 3.
1. Be sure that the power switch is in the OFF position.
2. Plug the end of the 12V AC adapter cord into the receptacle on the curved terminal track.
3. After connecting the adapter to the track, plug the 12V AC Adapter into a standard wall
outlet.
Move the switch to the ON position. The power light will illuminate and your ready to go
Warning!
This 12V AC Adapter is an electrical device and should not be connected to the
wall outlet by children.
Switch OFF
Switch ON
Figure 3. Power connections
Light turns on

Creating your layout
Placing the train on the track
With the track set up and power connected, you are ready to put your train on the track.
1. Place the locomotive on the track first, making sure that all wheels are set properly on the rails.
2. Place the coal tender behind the locomotive, lowering the coupler into position. See
Figure 5.
3. Plug the wire tether on the coal tender into the receptacle on the locomotive, just below the rear of
the cab. Refer to Figure 4.
Note!
The locomotive will not operate unless the wire tether between the locomotive and tender
is connected.
Tether
The locomotive will not operate
unless the wire tether between the
locomotive and tender is connected.
To disconnect the wire tether for
storage, squeeze the latch on the
bottom of the connector and remove
the plug from the locomotive.
Coupler
Figure 4. Locomotive and tender connection

Creating your layout
Placing the train on the track (continued)
5. Place the Calliope Car and caboose on the track, lowering the couplers into position. The
couplers are illustrated in Figure 5.
Couplers
Figure 5. Coupling the train

Operating the train
Operating the train
All aboard! Now you are ready to get your train under way. Slide the switch on the Power Lockon
to the ON position. The red light on the Lockon will illuminate, indicating that power is going to
the track. Be sure that all the cars’ lights are on; if they are not, check that all the wheels are correctly
placed on the track.
To turn the train and lights off, slide the power button on the Lockon to the OFF position. For even
longer periods it is recommended that the AC Adapter be removed from the wall outlet.
Use the Remote Controller to operate your train. Remove the battery cover on the controller
and insert two AAA batteries into the battery compartment. To operate the train you must aim the
controller in the general direction of the locomotive.
Note!
As with all infrared (IR) controllers, operation is impaired in intense or direct sunlight.

Operating the train
Remote Controller Functions
Aim the Remote Controller at the locomotive and use the
buttons to access the features.
FORWARD
The whistle blows two times, and the locomotive
moves slowly until the train reaches full speed. Music
automatically starts when the train is at speed.
REVERSE from Stop
The whistle blows two times, and the locomotive moves
slowly in reverse until the train reaches full reverse speed.
Note!
The music does not play when the train is
operating in reverse.
REVERSE from Forward
The bell rings, and the train slows to a complete stop. Once
stopped, the whistle blows two times, and the train moves in
reverse.
STOP
The bell rings, and the train slows to a complete stop.
Note the light remains on.
MUSIC VOLUME
• Press once to lower the volume of music. The train sounds are unaffected.
• Press a second time to turn off the music. The Santa, whistle, bell, and music buttons are disabled
when the volume is in this mode. The train sounds are unaffected.
• Press a third time to restore the music to the original volume level.
SANTA
Santa says "Merry Christmas!"
WHISTLE
The whistle blows.
BELL
The bell rings.
MUSIC
Three different holiday tunes are played by your train. Press the button again to advance to the next
song.
Note! The holiday tunes play only when the locomotive is moving forward.
10

Maintaining and servicing your set
Resolving short circuits
Your Lionel 12V AC Transformer is listed by Underwriters Laboratories Inc. and has been
carefully designed and tested to ensure peak performance.
Note!
The 12V AC Transformer must be unplugged from the wall socket when a short
circuit is noticed, and the short circuit must be corrected.
A short circuit is caused by a direct connection between the two rails. Shorts circuits will
automatically shut off the transformer and cut power to the train. Find and remove the cause
of the short circuit, and the transformer will reset itself within 60 seconds.
Derailed cars can cause a short circuit, so make sure that all wheels are properly set on the
rails. Some other causes of short circuits might be staples, nails, paper clips, or other metallic
objects lying across the rails.
After your 12V AC transformer has been operating for a while, it may become warm. It is
the nature of all electrical power equipment to become warm when in use. If your power pack
is loaded to capacity, let it cool down after several hours of use. Unplug the 12V AC adapter
from the wall when the train is not in use for long periods.
Note!
This train was designed to run with all cars included in this set and up to three
additional cars. Operating additional cars or accessories could cause your 12V AC
adapter to become overloaded.
Parents!
The AC adapter included in this set should be periodically examined for
conditions that may result in the risk of fire, electrical shock, or injury. In the
event that such a condition exists, the AC adapter should not be used until
properly repaired or replaced.
11

Maintaining and servicing your set
Cleaning the track
From time to time, it is important to clean the top surface of the track rails. This can be done with
a soft cloth or non abrasive metal cleaning cloth. Failure to do this periodically will cause the
train to run erratically, and eventually it will stop running altogether.
Replacing the lamp in the Caboose
The interior of your caboose is illuminated by one small lamp, Lionel part no. 602-538-9966.
During the course of normal operations, you may find that this lamp requires replacement.
Replacement lamps are available at your authorized Lionel Service Center or from Lionel Service
in Chesterfield, Michigan. This lamp is a standard micro light used on most common holiday light
strings.
To replace the lamp, lift the roof off the caboose cabin. Refer to Figure 6. Pull the expired lamp
straight up from its socket. Install the replacement and reposition the roof on the caboose.
Figure 6. Caboose lamp
12

Maintaining and servicing your set
Maintenance and lubrication
Do not attempt to disassemble and/or lubricate the motor on your locomotive. This locomotive
has been factory-tested, and the necessary internal parts have been sufficiently lubricated
at the factory for life. If your locomotive requires service, please bring it to an authorized Lionel
Service Station or Lionel Service for assistance. See the back of this Owner’s Manual for additional
information.
If you experience any squeaking around axles of the locomotive, you may use a drop or two of
Lionel Oil, available in the Lubrication and Maintenance Set (available separately, 6-62090).
Note!
It is very important to keep the track and wheels free from dirt and grease. Wipe them with
a soft cloth whenever they get dirty. This will help the locomotive run more efficiently.
13

Maintaining and servicing your set
Troubleshooting
Train will not run and lights are not on.
• Be sure that all track sections are securely connected.
• Check that the wire connecting the locomotive and coal tender is securely in its socket.
• Inspect all power connections (the AC adapter and the wire connecting the AC adapter to
the Lockon).
• Be sure that the Power Lockon is securely connected to one of the tracks with the notched
sections.
Train will not run but lights are on.
• Replacement lamps are available at your authorized Lionel Service Center or from Lionel
Service in Chesterfield, Michigan. This bulb is a standard micro light used on most
common holiday light strings.
• Check that the wire connecting the locomotive and coal tender is securely in its socket.
• Replace the batteries in the Remote Controller.
• Move the locomotive out of direct sunlight. Note that the controller is infra red and, like
television controllers, will not work in strong or direct sunlight.
Lights on some cars are not lit.
• Check to see that all the wheels of the cars not lit are on the tracks.
• Be sure the power pickups between the wheels are clean.
• Be sure the wire connecting the locomotive and coal tender is securely in its socket.
Music does not play.
• Be sure the train is moving forward. The music does not play when the train is in reverse.
• Press the VOLUME button on the controller.
14

Notes
15

Limited Warranty/Lionel Service
This Lionel product, including all mechanical and electrical components, moving parts, motors and
structural components, except for light bulbs, is warranted to the original consumer-purchaser, for one
year against original defects in materials or workmanship when purchased through an authorized Lionel
merchant.
This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of
commercial use, or damage resulting from abuse or misuse of the product by the purchaser. Transfer of
this product by the original consumer-purchaser to another person voids this warranty. Modification of this
product voids this warranty.
Any warranted product which is defective in original materials or workmanship and is delivered by the
original consumer-purchaser to Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof
of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or
labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the
original purchase price will be granted. Any products on which warranty service is sought must be sent freight
or postage prepaid, as transportation and shipping charges are not covered by the warranty.
In no event shall Lionel L.L.C. be liable for incidental or consequential damages.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
exclusion may not apply to you.
This limited warranty gives you specific legal rights, and you may have other rights which vary from state
to state.
Instructions for Obtaining Service
If service for this Lionel L.L.C. product is required, bring the item, along with your dated sales receipt and
completed warranty information to the nearest Authorized Lionel Service Center. Your nearest Lionel Service
Center can be found by calling 1-800-4-Lionel, or by accessing our Website at www.lionel.com.
If you prefer to send your product back to Lionel L.L.C. for repair in Michigan, you must first call
586-949-4100 or FAX 586-949-5429, or write to Customer Service, P.O. Box 748, New Baltimore, MI
48047-0748, stating what the item is, when it was purchased and what seems to be the problem. You will be
sent a return authorization letter and label to ensure your merchandise will be properly handled upon receipt.
Once you have received your return authorization and label, make sure that the item is packed to prevent
damage during shipping and handling. We suggest that you use the product’s original packaging. This
shipment must be prepaid and we recommend that it be insured.
Please make sure you have followed all of the above instructions carefully before returning any
merchandise for service. You may choose to have your product repaired by one of our Authorized Lionel
Service Centers after its warranty has expired. A reasonable service fee will be charged.
Warranty Information
Please complete the information below and keep it, along with your dated sales receipt. You must present
this and your dated sales receipt when requesting warranty service.
Name
Address
Place of Purchase
Date of Purchase
Product Number
Product Description
©2008 LIONEL L.L.C., CHESTERFIELD, MI 48051-2493
UNITED STATES OF AMERICA
PRINTED IN CHINA