uP200:Layout 1.qxd - Prodrive

prodrive.com

uP200:Layout 1.qxd - Prodrive

where inspiration and innovation combine

MICROPROTEUS TM UP200 / MPC565


MicroProteus TM is a highly compact and rugged electronic control unit,

powered by an automotive specification Motorola MPC555 processor.

The uP200 unit provides full rapid prototype capabilities through the use of

MATLAB ® generated autocode.

uP200 is ideal for use in a multitude of embedded real time applications

that require a 32 bit floating point processor coupled with onboard I/O,

e.g. suspension and driveline control.

DIGITAL SUBSYSTEMS

• Motorola MPC565 “SpanishOak” microcontroller at 56MHz

• 1Mb external SRAM

• 8Kb non-volatile RAM

• Integrated Prodrive internal datalogger

-Log external and Simulink signals

-Logs at model iteration rate

-Available with up to 1Gb memory

• Custom hardware interface – internal Daughter boards

-LVDT / VR / Differential Analogue / Accelerometer

• Software compatibility with Prodrive blockset, MATLAB ® (Simulink ® ,

Stateflow, Real-Time Workshop, Embedded Target for MPC555) and PIPPA TM

• DIAB and GNU complier support (GCC included with Prodrive software suite)

ENVIRONMENTAL

• Mechanical package: All aluminium, milled from solid case

• Weight:

595g

• Dimensions:

153mm x 72mm x 49mm

• Storage temperature: -40° to +125°C

• Operating temperature: -40° to +85°C (tested to 100°C)

• Sealing:

IP67

• Drop:

Random drop on concrete from 1m

• Vibration:

Tested to 20g RMS for 2 hours

uP200 has an integrated internal datalogger, available in up to 1Gb memory

size. The data logger is configured via Simulink ® blocks (supplied as part of

the Prodrive Software suite). The logging rate can be any multiple of the

model iteration rate (typically 1ms).

COMMUNICATION

• 3 x CAN (2.0b) buses * Supports CCP (CANape & INCA)

• 3 x RS232 serial ports *

• USB datalogger upload

* only two of the four available communication interfaces can be used at any one time

I/O SUBSYSTEM & POWER SUPPLY

• 24 x single ended analogue inputs

• 12 x digital inputs

• 16 x 2-Amp low side drives, with built in diagnostic capability +

• 5x 5A H-Bridges with current feedback +

• 8x 8A low side drive with current feedback +

• 4x analogue outputs (5mA)

• 2 x rugged autosport connectors (55 & 66 way), EMC Filtered

• Wide supply range (7-26V), with reverse over voltage and temperature

protection

+ Subject to total ECU power dissipation of 70W

ADDITIONAL PRODUCT INFORMATION

• Internal temperature sensor

• Internal battery voltage sensor

• Status / “Heartbeat” LED integrated into the case

• Configurable* pull up / pull down resistors on both analogue and digital inputs

• Configurable* thresholds on digital inputs

• 3 x sensor power supplies

* Please enquire about configuration options when ordering. Additional charge may apply

Note: The following products are required:

MATLAB R13 or MATLAB R14 including :-

• Simulink ® , Real Time Workshop ® , Stateflow ® (optional), Stateflow coder ® (optional)

Compiler

• GNU (GCC included with Prodrive software suite) or Windriver Diab TM ‘C’ Compiler

version 4.3, 4.4, 5.0

Prodrive reserves the right to amend product specification without prior notice. E & O E

• Any Simulink ® variable or external input to the ECU can be logged

• Data uploaded via USB, for viewing in PIPPA, CSV or MAT format

PRODRIVE KENILWORTH WARWICKSHIRE CV8 1NR T. +44(0)1676 536002 F. +44(0)1676 536205 E. ELECTRONICS@PRODRIVE.COM

WWW.PRODRIVE.COM/ELECTRONICS

More magazines by this user
Similar magazines