Wall Mounting Bracket - Appliances Online

appliancesonline.com.au

Wall Mounting Bracket - Appliances Online

OWNER’S MANUAL

Wall Mounting Bracket

Please read this manual carefully before operating

your set and retain it for future reference.

LSW100B

LSW100BG

P/NO : MFL63640503 (1101-REV03)

www.lg.com


* 1 Year Warranty

If material or workmanship proves defective under normal use, during the warranty period, please

contact the retailer where you purchased it. This warranty is good only to the original purchaser of

the product and effective only in the local area.

Component

Wallmount anchor

4 units

Wall mount screw

8 units

User manual

PVC Washer

4 units

Set protection cushion

4 units

Set screw

M4 X 10mm 4 units

M4 X 14mm 4 units

* Due to the shallow clearance between the display and the wall, the LSW100B Wall Mounts

may require the use of the included angled adapters.



* Note that the included angle adapters may block other connections on the back of the TV.

* Make sure the connectors on the cables connected to the display do not press against the wall.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Warning

This wall mount should be installed by a trained and

experienced installer designated by the retailer.

Having the product installed by a non-specialized installer is

very dangerous and can cause damage or injury.

Use a trained and experienced installer to move or

replace the wall mount, if needed.

Installation requires special techniques and moving or installing

the product on your own can cause serious safety issues.

Do not install the product where the weight cannot be

supported.

If the strength of the location where the wall mount is installed

is not strong enough, it can fall off and cause an injury.

After installing the wall mount, do not hang on the

product or apply severe impact to the product.

The product can fall off and cause injury.

When installing the wall mount, never hang the

power or signal cable on the rear side the TV.

The cord can be damaged and cause a fire, an electric

shock or damage to the product.

2


Install the product according to the directions in the

user manual.

If the product is not installed based on the directions in

the user manual, it can cause a serious injury or damage

to the product.

Caution

When installing the product or adjusting the height of

the product after installing, always do so with 2 people.

Working alone can cause the product to fall off and result in

injury or damage to the product.

ENGLISH

During the installation, check the type of wall

material and use the sealed anchor and screw if the

conditions comply.

If you do not use the designated anchor or screw, the

mount may not be able to withstand the weight of

the product and cause a safety issue.

Do not wipe the product with a wet towel and do not use any

heater or humidifier below where the product is installed.

If water flows into the product or if moisture and heat are applied to the

product, it can cause a fire, an electric shock or problem to the product.

Unplug the power cord from the power outlet before

installing the product.

If you install the product with the power cord plugged, it can

cause an electric shock or a fire.

When drilling holes in the wall, always use a drill bit

and drill of designated diameter. Also follow the

designated directions for the depth of the hole.

If the product is installed without following the designated

method, the product may be unstable and cause a safety

issue.

Do not install the product near any object that may

cause vibration.

Do not install the product near any high voltage power

cable or power source.

Do not install the product with bare hands. Always

wear proper work gloves.

It can cause an injury.

Do not allow the video connectors connected to the

display to press against the wall. Use the included

right-angle adapters if needed.

Only use attachments/accessories specified by the

manufacturer.

Before installation

* Do not use the product for purposes other than mounting a display on the wall.

* When installing/using the wall mount, be cautious of product damage and avoid accidents.

* If you have not fully read and understood the installation manual, do not install the product and contact

the dealer to have a specialized installer install the product for you.

* Even if you are not a specialized installer, it is advantageous to have experience in mechanical or

construction field in completely understanding this manual and installing the product.

* This product is designed to be mounted to walls that use standard intervals between the studs.

* Install the screw to attach the wall mount so that it can be assembled at the center from both ends of

the studs.

Use of stud finder, a separate device, is recommended.

* Install the product only on a vertical wall.

The manufacturer is not responsible for issue from installing the product on severely wall or on the

ceiling.

* Keep the included accessories out of reach of babies or children as it can cause safety issues including

suffocation from swallowing the parts.

* Make sure screws are tight against the wall, but do not overtighten.

* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.

* Be careful with the tools used during installation to prevent accidents or damage.

3


Installation method

- Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4mm drill bit for wood or steel / Level /

Stud finder / Drill. You may also need an 8mm socket wrench or an 8mm drill bit for concrete.

1 Separating the TV bracket

1

3

Safety pin

2


1. After expanding the wall mount forward as shown in Fig. 1, separate the safety pin from the wall mount as

shown in Fig. 2.

2. Separate the set bracket as shown in Fig. 3.

2

Attaching the mounting bracket on the TV

Make sure the screws are fully tightened to the bracket and display. If the screws will not fully tightened, they

might be too long or the wrong size.

VESA 100X100 / VESA 200X100 is supported.

If needed, you may refer to the display's user manual to verify the display has one of the supported VESA formats.

Screws are included for the following models:

M4 X 10mm

: 19/22LD*, 19/22LE*, 19/22LX*, 19/22LK*, 19/22LZ*,

19/22LW*, 19/22LV*, 26LE65*

M4 X 14mm

: 26/32LD*, 26/32LE*(Excludes 26LE65*), 26/32LX*,

26/32LK*, 26/32LZ*, 26/32LW*, 26/32LV*

Bracket to attach to

the display

VESA 200


1. Check to see if the display has screws already installed into the VESA mounting holes. If so, remove those.

2. Attach the bracket to the back of the display as shown above. Use a Phillips head "+" screwdriver to tighten the

screws.

- At this time, be careful to prevent the set from falling down.

- Make sure the screws are fully tightened to the bracket and display.

4

VESA 100

VESA 100

Install the PVC washer between the brackets

and the display on the following models :

32LE53*/32LE55*

But for 26LE53*/26LE55* model,

this is provided as TV component.


3

How to attach to masonry walls

- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry

brick and hallow block that do not crack.

Please follow the below direction.

ENGLISH

- Check the material of the wall and the thickness of the finishing.

- When installing the product on the wooden wall, refer to page 6.

- When installing the product on wall material not designated, install the product so that each fixated location

can withstand the pull out load of 70kgf (686N) and shear load of 10kgf (980N) or above.

Anchor

a

b

c

Wall mount screw

d

e

- Use the Ø8mm drill bit for concrete and hammer (Impact) drill.

a. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm.

b. Clean the drilled hole.

c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)

d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face

upward.

e. Align the wall mount bolt to the hole and tighten it. At this time, the bolt must be tightened with torque of 45kgf/cm

or above.

4

How to install the wall mount


→When you separate the 4 screws on the wall mount connected to the wall bracket for use with a wooden wall,

it is much easier to install the product.

A

Wall mount

screw

Separate the wall mount screw.

→When installing the product on a masonry wall, turn the 4

screws on the A part counterclockwise to separate the

screw and bracket.

→After aligning the wall bracket to the location to install,

mark the part to screw on the wall and then remove the wall

bracket.

→Refer to page 4 to attach the wall bracket.

→Use a level to check whether the wall mount is level.

→f the screw cannot be assembled in the designated location

inevitably, it can be assembled by rearranging to the closest

location. But, do not change 2 or more locations from the

designated spot.

→Assemble the wall mount screw on 1 left and 1 right location

on the top part and 1 left and 1 right location on the bottom

part.

→At this time, use a "+" driver (Manual or motorized) or 8mm

wrench to tighten the screw so that the wall, wall bracket and

screw are completely pressed against one another.

5


76mm

drywall

406mm

wood stud

drywall

a. Locate and mark the centers of the wall studs using a stud finder.

b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and

then remove the wall bracket.

c. Use a level to make sure your screw marks are level.

d. Use the 4mm drill bit for wood to drill holes with the depth of 76mm or above where the wall mount screw location is marked

on the wall.

e. Clean the drilled hole.

f. Tighten the wall mount screws for the wall bracket on the drilled hole.

→ At this time, tighten the screw so that the wall, wall bracket and the wall mount screw are pressed against one another.

(Drywall can be damaged when tightened with excessive force, please be careful.)

→ When tightening the screw use the "+" driver (Manual or motorized) or 8mm wrench.

5

How to assemble the wall mount support and display

- Always install the display with 2 or more people.

Safety pin

→ After mounting the display, insert the safety pin as

shown. If the safety pin is not fixated as shown in

the picture, the display can fall.

→ After the install is finished, pull the bottom part of

the display to verify the product is attached

securely.

→ In using cables or accessories not provided with

the wall mount, make sure to keep a certain

distance from the wall so that excessive force is

not applied on cables or accessories.

How to level the Display

6 If the product is not leveled after the

installation, you can rotate the display

up to 5 degrees.

7

Cable arrangement and set protection cushion

- Arrange the cables as shown in the picture. Use some type of cable banding

device to hold all the cables together. Attach the set protection cushion to

mitigate the impact between the wall and the set when adjusting the angle.

Attach the set protection cushion as shown in the picture.

± 5°

± 5°

6


Product specification

-15° ~ +15° ± 2°

[ Unit : mm ]

ENGLISH

-15° ~ +15° ± 2°


Max.

Min.


116


Max. 116


20

Min.

20

Model Name

LSW100B/LSW100BG

Model Name

LSW100B/LSW100BG

Width (mm) 221

Width (mm) 435

Height (mm) 152

Height (mm) 167

Depth (mm) 14

Depth (mm) 20

Weight (kg) 0.9

Weight (kg) 1.7

Wall Mount VESA Specification 100 X 100/200 X 100

Wall Mount VESA Specification 100 X 100/200 X 100

Max. UL Load Capacity (kg) 15

Max. UL Load Capacity (kg) 15

7


The model and serial number of the

product is located on the back or one

side of the product. Record it below

should you ever need service.

MODEL

SERIAL

Supported Displays:

19/22/26/32LD*

19/22/26/32LE*

19/22/26/32LX*

19/22/26/32LK*

19/22/26/32LZ*

19/22/26/32LW*

19/22/26/32LV*

More magazines by this user
Similar magazines