Imprägnier-Lasur TC 6303 - Tex-Color
Imprägnier-Lasur TC 6303 - Tex-Color
Imprägnier-Lasur TC 6303 - Tex-Color
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Technical Data Sheet<br />
Thoroughly wash down/clean tropical woods and high-resin, tacky<br />
wooden surfaces using <strong>Tex</strong>-<strong>Color</strong> Nitroverdünnung and allow to flash<br />
off thoroughly. Pitch pockets must be burnt out. Corners must be<br />
rounded.<br />
The moisture content of the wood should be measured in several<br />
places at a depth of at least 5 mm. For softwood this should be no<br />
more than 15%, for hardwood no more than 12%.<br />
Greyed wood must be removed completely using mechanical<br />
techniques to reveal the healthy wood. Check that the substrate/old<br />
coating is suitably compatible with the new varnish before<br />
application.<br />
Also give consideration to the structural preservation of wood used<br />
outdoors. Damage to the coating may occur if the wood has not been<br />
structurally preserved properly.<br />
See also VOB*, Part C, DIN 18 363, Section 3, “Painters and<br />
varnishers” (*Contract procedures for building works - Part C;<br />
General technical specifications for building works).<br />
Application Guide<br />
<strong>Tex</strong>-<strong>Color</strong> Imprägnier-<strong>Lasur</strong> <strong>TC</strong> <strong>6303</strong> should be shaken or stirred<br />
before use, and occasionally whilst working.<br />
It is advisable to apply the product using artist's or decorator's<br />
brushes or by using a dipping method.<br />
Softwoods and hardwoods that are at risk from rot, fungus or blue<br />
stain must be impregnated with 2 coats of <strong>Tex</strong>-<strong>Color</strong> Holzschutzgrund<br />
<strong>TC</strong> 6301 farblos (colourless) by either brushing or dipping.<br />
Structural components and/or woods that are exposed to very harsh<br />
weathering effects should be provided with a further final coat of <strong>Tex</strong>-<br />
<strong>Color</strong> Imprägnier-<strong>Lasur</strong> <strong>TC</strong> <strong>6303</strong>. Please take into consideration that<br />
the colour of the finish will be intensified with each additional coat.<br />
Use Imprägnier-<strong>Lasur</strong> farblos (colourless) if required.<br />
Restorative work<br />
(After 2 - 3 years) Brush off surface and clean, apply one coat of<br />
<strong>Tex</strong>-<strong>Color</strong> Imprägnier-<strong>Lasur</strong> <strong>TC</strong> <strong>6303</strong> farbig (coloured) and one coat<br />
of Imprägnier-<strong>Lasur</strong> farblos (colourless).<br />
Note: Colourless <strong>Tex</strong>-<strong>Color</strong> Imprägnier-<strong>Lasur</strong> <strong>TC</strong> <strong>6303</strong> can be used<br />
to lighten darker colours. Do not use the colourless product on its<br />
own.<br />
Quantities<br />
Cleaning of tools<br />
Drying time<br />
Application temperature<br />
Approx. 12 ml/m², dependent on the roughness of the substrate.<br />
If a precise calculation is required then a test coat should be applied<br />
to an appropriate surface.<br />
Clean using turpentine substitute or <strong>Tex</strong>-<strong>Color</strong> Pinselreiniger paint<br />
brush cleaner.<br />
Dust dry after approx. 4 hours at temperatures of approx.+20 °C and<br />
max. 65% humidity. Touch dry after approx. 8 hour. Can be sanded<br />
and painted over after approx. 12 hours.<br />
These times may increase depending on the temperature and<br />
humidity.<br />
The temperature of the surrounding environment and item being<br />
painted should be at least +5 °C during application and drying.<br />
Imprägnier-<strong>Lasur</strong> <strong>TC</strong> <strong>6303</strong> Page 2 of 3