Virtual Connect SAN Cookbook.pdf - Sallustio.ch

More documents

Recommendations

Info

6. Then identically, create two VC SAN Fabrics, Fabric_2-Tier1 and Fabric_2-Tier2 attached this time to the second VC-FC module, Fabric_2-Tier1 with 3 ports: and Fabric_2-Tier2 with one port: Scenario 3: Multiple VC SAN fabrics with Dynamic Login Balancing connected to the same redundant SAN fabric with different priority tier 48
7. Four VC fabrics have been created, two for the server group Tier1 with three uplink ports and two for the guaranteed throughput server Tier2 with one uplink port. Defining a new VC SAN Fabric via CLI To configure the VC-FC modules from the CLI: 1. Log in to the Virtual Connect Manager CLI using your favorite tool. 2. Enter the following commands to create the fabrics and assign the uplink ports: add fabric Fabric_1-Tier1 Bay=5 Ports=1,2,3 add fabric Fabric_1-Tier2 Bay=5 Ports=4 add fabric Fabric_2-Tier1 Bay=6 Ports=1,2,3 add fabric Fabric_2-Tier2 Bay=6 Ports=4 Scenario 3: Multiple VC SAN fabrics with Dynamic Login Balancing connected to the same redundant SAN fabric with different priority tier 49
Page 1 and 2: HP Virtual Connect Fibre Channel Ne
Page 3 and 4: Contents About this document ......
Page 5 and 6: Summary ...........................
Page 7 and 8: Considerations and concepts Key tak
Page 9 and 10: Virtual Connect Fibre Channel suppo
Page 11 and 12: Supported VC SAN Fabric configurati
Page 13 and 14: 10/100Base-TX 6 15 16 13 14 11 12 9
Page 15 and 16: Multiple-fabric Support Support for
Page 17 and 18: 12Vdc HP StorageWorks 4/32B SAN Swi
Page 19 and 20: Port Group Beginning with version 1
Page 21 and 22: Uplink port path failover: The modu
Page 23 and 24: Link stability This interval define
Page 25 and 26: Scenario 1: Simplest scenario with
Page 27 and 28: For more information about configur
Page 29 and 30: 4. Create a new VC Fabric named Fab
Page 31 and 32: Blade Server configuration Server p
Page 33 and 34: NOTE: Static Login Distribution has
Page 37 and 38: 1. Create a VC SAN Fabric by select
Page 39 and 40: 4. Create a new VC Fabric named Fab
Page 41 and 42: Blade Server configuration Server p
Page 45 and 46: Defining a new VC SAN Fabric via GU
Page 47: 4. Create a new VC Fabric named Fab
Page 51 and 52: 2. Under FC SAN Connections, select
Page 53 and 54: Scenario 4: Multiple VC SAN fabrics
Page 55 and 56: Considerations Each Virtual Connect
Page 57 and 58: first VC-FC module (Bay 5). 3. On t
Page 59 and 60: 6. Then identically, create two VC
Page 61 and 62: 2. Enter the following commands to
Page 63 and 64: The VC module uplink ports are phys
Page 67 and 68: Figure 18: FlexFabric Module port c
Page 69 and 70: Defining a new VC SAN Fabric via GU
Page 71 and 72: 4. Select either Manual or Automati
Page 73 and 74: 7. Two VC fabrics have been created
Page 75 and 76: Defining a new VC SAN Fabric via CL
Page 77 and 78: Scenario 6: Adding VC Fabric uplink
Page 79 and 80: a. For a Brocade SAN switch: Portsh
Page 81 and 82: 3. The upstream SAN switch shows th
Page 83 and 84: 2. Click Add Port, select the port
Page 85 and 86: Figure 26: Hot adding one uplink po
Page 87 and 88: 2. Click on the Server connections
Page 89 and 90: Summary This scenario demonstrates
Page 91 and 92: 2. Click the DPVM Setup icon. The D
Page 93 and 94: 7. Select all VC-FC fabric devices
Page 95 and 96: Appendix A: Blade Server configurat
Page 99 and 100:
Defining a Server Profile with FC C
Page 101 and 102:
7. Assign the profile to a server b
Page 103 and 104:
Appendix B: Blade Server configurat
Page 105 and 106:
12Vdc HP StorageWorks 4/32B SAN Swi
Page 107 and 108:
Defining a Server Profile with FCoE
Page 109 and 110:
8. The server can now be powered on
Page 111 and 112:
Appendix C: Brocade SAN switch NPIV
Page 113 and 114:
3. To be sure that the port is enab
Page 115 and 116:
Appendix D: Cisco MDS SAN switch NP
Page 117 and 118:
6. Click the FLOGI tab. In the Port
Page 119 and 120:
NPIV is enabled globally on the swi
Page 121 and 122:
2. Click npiv. 3. In the Action col
Page 123 and 124:
7. Click the FLOGI tab. In the Port
Page 125 and 126:
7. To verify that NPIV is properly
Page 127 and 128:
Appendix F: Static Login Distributi
Page 129 and 130:
4. Select Static Login Distribution
Page 131 and 132:
12. Click Name Server on the left s
Page 133 and 134:
Or on the first FlexFabric module (
Page 135 and 136:
2. In the same Interconnect Bay scr
Page 137 and 138:
2. Click Name Server on the left si
Page 139 and 140:
Testing the loss of uplink ports In
Page 141 and 142:
2. VC Uplink port X1 port status be
Page 143 and 144:
On the server side, the Boot from S
Page 145 and 146:
Figure 29: Emulex showing Boot from
Page 147 and 148:
Figure 32: Emulex showing Boot from
Page 149 and 150:
Acronyms and abbreviations Term BIO
Page 151 and 152:
Reference NPIV and Fibre Channel in
show all

Virtual Connect SAN Cookbook.pdf - Sallustio.ch

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?