Elegant Entry Divider - Wood Tools
Elegant Entry Divider - Wood Tools
Elegant Entry Divider - Wood Tools
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
EDOE<br />
A Freud's new roiseo<br />
ponel bits (ogee profile<br />
shown) hove two extro<br />
cutters for smoother, foster<br />
cuts on roised ponels.<br />
beiler bits for moking<br />
RAISED PANET DOORS<br />
Ifyou're serious about making raised<br />
panel doors, then give Freud's new<br />
raised panel bits a closer look.These<br />
router bits have some big advantages<br />
over other raised panel bits - most<br />
notably in the way they cut.<br />
Most raised panel bits have two<br />
carbide cutting edges on a body<br />
that's 2" to 3" in diameter. The bits<br />
remove so much material that a<br />
series of progressively deeper passes<br />
is often necessary to achieve a<br />
smooth surface.<br />
2+2 Technology - Freud has<br />
improved on this situation by adding<br />
r\rvo more cutters to its raised panel<br />
bits. Moreover, the rwo large cutters<br />
cut upward, and the two small cutters<br />
cut downward to generate a shearing<br />
action that creates flawless, consistent<br />
cuts, even on end gratn (Art,left).<br />
Backcutter - Freud also added<br />
a backcutter to these bits.This means<br />
that one bit can cut both sides ofa<br />
panel in one pass.The cut creates a<br />
tongue that fits into grooves in the<br />
door rails and stiles.This is a marked<br />
improvement over other raised panel<br />
bits, which require you to rabbet the<br />
back ofthe panei to fit into grooves.<br />
The Freud bits are designed to<br />
cut 3/4"-thick stock and require a<br />
router table equipped with a fence<br />
and a variable-speed router. (The<br />
bits should run at 10-12,000 RPM.)<br />
It takes a few test cuts to get the<br />
depth and fence settings just right,<br />
but once in use, these bits cut more<br />
smoothly than any other raised panel<br />
bits I've used.<br />
The Freud bits are available with<br />
three different profiles - bevei, cove,<br />
and ogee (shown) - for g1 10 each,<br />
or in a kit with rail and stile bits for<br />
$200.Visit Frer-rdTbrols.conr, or call<br />
800 -472-7 307 for more information.<br />
q drill bit for<br />
CURVED HOLES<br />
Scoring Boliom The new 3D drill bit fromtend board and exits through the<br />
resembles a standard Forstner edge<br />
j'qqr#iT<br />
an application that conres in<br />
bit. But it cuts in ways that handy for running cable, stereo wire.<br />
or electrical conduit (Photo, right).<br />
V'<br />
il , Forsrner Dlr can [.<br />
How It Cuts - The The bit can also create an open<br />
,{\<br />
bit has sharp cutting edges<br />
on the sldes, as well as the<br />
botto- ofthe bit (Art, lef).<br />
So once the bit enters a<br />
channel along the face of a workpiece<br />
for putting wire below the suface of<br />
the wood.To do this,you simply drill<br />
until the cutterhead is about halfway<br />
hole, pivoting the drill causes these<br />
side cutting edges to curve into the<br />
wood, creating a curved or widened<br />
channel.The result is a drill bit with<br />
some great DIY applicatrons.<br />
into the board. Then, pivot the drill<br />
sideways and cut along the suface. It<br />
works great as a standard drill bit, too.<br />
Tiend's 3D bits are available individually<br />
in diameters from 1/+" to<br />
DIY Uses - One of the tasks a 71/q",or in four- and eight-bit kits.<br />
3D bit excels at is cutting a curved<br />
channel that enters the face of a<br />
For more information, call 859-485-<br />
2080, or visit Trend-USA.corr<br />
A Cutting curved holes in wood<br />
is iust one of mony home improve<br />
ment tosks this new 3D drill bit<br />
from Trend con tockle.<br />
.A<br />
LA<br />
woRKBENCH U FEBRUAnv 2005