NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion ... - Nyt Smil

nytsmil.dk

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion ... - Nyt Smil

NVV-B601

B601NVV

NVV-B604

B604NVV

NVV-B605

5 iin1 Diiamond Dermabrasiion

Syystem

User Manual

Revision Date: October 20, 2009

© 2009 Bella Beauty aps, Nova Newface.eu. All rights reserved.

All of the material contained within this document shall remain the property of Company name unless specifically noted.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

mechanical, electronic, photocopying, recording, or otherwise, without prior written permission of Company Name.

All other elements mentioned in this guide are registered to those companies.


Table of Contents

SAFETY WARNINGS ........................................................................................................... 3

TECHNICAL SPECIFICATIONS .............................................................................................. 3

INTRODUCTION TO DIAMOND MICRODERMABRASION ............................................................ 4

Benefits ........................................................................................................................................................... 4

When Not to Use ............................................................................................................................................ 5

Side Effects ..................................................................................................................................................... 5

Usage Options ................................................................................................................................................ 5

General Skin Care ................................................................................................................................. 5

Treat Skin Conditions ............................................................................................................................ 5

SYSTEM DETAILS............................................................................................................... 8

System Overview ........................................................................................................................................... 8

Connections............................................................................................................................................ 8

Front Panel ............................................................................................................................................. 9

Accessories (Functions) ........................................................................................................................ 9

Diamond Dermabrasion ......................................................................................................................... 9

Skin Scrubber ....................................................................................................................................... 12

Hot & Cold Hammer ............................................................................................................................. 14

Ultrasonic .............................................................................................................................................. 15

Photon ................................................................................................................................................... 16

Troubleshooting ............................................................................................................................................ 17

TREATMENT INSTRUCTIONS .............................................................................................. 20

Pretreatment ................................................................................................................................................. 20

System .................................................................................................................................................. 20

Client ..................................................................................................................................................... 20

Treatment...................................................................................................................................................... 21

Treating the Face ................................................................................................................................. 21

Treating the Body ................................................................................................................................. 22

Post-Treatment ............................................................................................................................................. 25

INDEX ............................................................................................................................. 26

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Safety Warnings and Technical Specifications 3

Safety Warnings

Observe the following warnings when operating the system:

• Never operate the system on a client who suffers from any of the following medical conditions:

o Heart disease

o Sensitive skin

o Alcoholism

o Asthma

o Irregularities of the heart

o Has a pacemaker or defibrillator implanted

o Epilepsy

o Currently experiencing a cold, flu, or gastrointestinal upset

o Pregnancy

o Ulcers

o Disease of the stomach, intestine, liver, or pancreas

o Currently being treated for any form of cancer

o Major surgery in the past year

o Any serious condition not listed above

• Do not use the system on the following areas:

o Skin that is severely damaged, inflamed, or infected

o Skin rash

o Surgical scar that is 12 or less months old

o Swollen skin

o Genitals

• The system must be grounded.

• Use a suitable product, such as a gel or emulsion when using the system for deep cleaning.

• Do not position the handle of any of the accessories in any one area of the skin without moving.

Always keep the accessories moving across the skin.

• Never position any accessory handle towards the eyes, throat, or chest.

• Do not make any modifications to the system.

• Do not immerse the system or any of the accessories in water.

• Always clean the accessories after operating the system, and store the system in a cool and dry

place.

Technical Specifications

Table 1: Technical Specifications

Voltage Power Packing Size Weight

220V-240V/50 Hz

140W Fuse: 3A 51*48* 32 cm 11kg

100V - 120V/60 Hz

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Chapter 1:

Introduction to Diamond Microdermabrasion

The skin is the most visible part of the human body. When imperfections appear, the choices for recovery

are natural healing or cosmetic correction. The skin’s natural healing process depends on the structure

and condition of its three major layers: epidermis, dermis, and subcutaneous layer (see Figure 1). The

epidermis is the top layer of the skin, and in itself contains several layers. The dermis lies just under the

epidermis and is comprised of connective tissues, collagen, nerves, sensory receptors, hair follicles, and

several types of glands. The subcutaneoous layer of the skin, also known as the oil gland, contains many

blood vessels that are responsible for providing nourishment to the skin. Because of the depth of the skin,

it can take as long as 14 days to eliminate the visual signs of a superficial blemish. Imperfections that are

more severe than this can take even longer. The time it takes for the skin to renew itself depends on the

depth of the imperfection as well as the condition of the upcoming skin cells.

epidermis layer

dermis layer

Figure 1: Skin Layers

Subcutaneous layer

There are many cosmetic processes available to correct skin imperfections and enhance the quality of the

skin. Microdermabrasion is considered one of the most effective systems to improve the skin with the

fewest possible side effects and complications. The process of microdermabrasion involves using a

mechanical device to remove the epidermis and stimulate the area to produce rejuvenating effects. The

abrasion part of the process involves the use of aluminum-oxide crystals. The crystals are swept across

the skin to remove the epidermis layer of the skin. The machine then sucks the crystals and dead skin

cells back up through a vacuum. Microdermabrasion is effective, but the oxide crystals can cause

problems.

Diamond microdermabrasion is the latest generation of microdermabrasion. The exfoliation of the

epidermis is performed with a diamond-tipped wand instead of crystals. With even, steady pressure, a

diamond-tipped wand is swept across the treatment area. During the process, the skin must come in

close contact with the diamond-tipped wand. Like microdermabrasion, there is a vacuum “action” that

eliminates dead skin cells and promotes healthy skin renewal.

Benefits

There are several key benefits associated with using diamond microdermabrasion, including the

following:

• No exposure to dangerous crystals or dust particles

• Can treat delicate areas surrounding the nose, eyes, and mouth

• Significant control of the treatment process, which promotes accuracy

• No crystals to clog up machine

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Introduction to Diamond Microdermabrasion 5

When Not to Use

Diamond microdermabrasion is effective for just about everyone. The following are the most common

situations in which diamond microdermabrasion is not recommended:

• Pregnancy

• When certain skin conditions exist, such as dermatitis, psoriasis, or active eczema or rosacea

• On individuals with undiagnosed skin lesions or unstable diabetes should contact their medical

physician for advice

• If you are presently using an acid skin peeler or other skin treatment, you should not use the

diamond microdermabrasion procedure

• On skin that is sensitive, swollen, or that contains a scar that is under a year old

Side Effects

There are a few minor side effects associated with diamond microdermabrasion. Exfoliating the epidermis

level of the skin may temporarily result in slight redness and/or soreness. Applying a small amount of

moisturizer after treatment can help to soothe the skin.

When treating acne, exfoliating the epidermis may result in some bacteria coming to the surface of the

skin. The client may notice tiny spots, but these are temporary.

Usage Options

Diamond microdermabrasion is effective for superficial skin conditions, as well as skin conditions that

involve deeper damage. The following are a list of some of the usage options for diamond

microdermabrasion.

General Skin Care

A lot of factors can affect the quality of an individual’s skin. Genetics plays a big part. However, the

environment, stress, nutrition, and cleansing regimen can also contribute to unhealthy skin. There are

many products on the market that are designed to cleanse the skin. However, they are typically

ineffectual at penetrating deep enough into the skin to make a difference in its quality. Often, the

cleansing is just superficial. By resurfacing the epidermis, diamond microdermabrasion is an effective tool

for combating these effects and can actually help to restore the skin to a healthy state.

Treat Skin Conditions

The skin can become afflicted with numerous skin conditions. Diamond microdermabrasion is most

effective for those conditions that affect the outermost layers of the skin, including the following:

Acne

• Acne

• Rosacea

• Hyperpigmentation

• Aging Skin

• Photoaging

There are many myths about acne and how it develops. It is actually a disorder that stems from the hair

follicles and sebaceous glands of the dermis layer of the skin. Acne is linked to three possible causes:

follicular hyperkeratinization, bacteria, and the production of sebum. Either of these causes the production

of androgen to increase. Under the epidermis layer of the skin, oil and dead skin become trapped, which

causes inflammation. The inflammation eventually reaches the epidermis in various forms, including

whiteheads, blackheads, pustules, and cysts.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Introduction to Diamond Microdermabrasion 6

By exfoliating the epidermis layer of the skin, diamond microdermabrasion is able provide room for the

skin to breath to unclog the pores. The process also kills the bacteria under the epidermis. These are two

of the biggest culprits in the formation of acne. The recommended treatments for acne is every 7-12 days;

8-10 treatments.

Rosacea

The cause of the redness and swelling of the skin that is characteristic of rosacea is unknown. The

condition is typically considered chronic. Rosacea may strike anyone, but the typical sufferer is fairskinned

and between the ages of 30 and 50. Rosacea most often affects the face, but other parts of the

body, especially the back, may be affected. The classic symptoms of rosacea include the following:

• Flushing on the face and neck

• Red lines in affected area

• Bumps covering the nose

• Face burning or itching

• Dry skin

• Pimples

There are several forms of rosacea that are characterized by the symptoms. Diamond microdermabrasion

is a viable solution as long as the rosacea is not active. The sooner a diagnosis is made and treatment

started, the better the outlook.

Hyperpigmentation

Skin that consists of uneven dark spots is characterized as being plagued by hyperpigmentation. The

causes of this condition vary and typically include sun damage, side effects from medication, and skin

inflammation, and acne scarring. Diamond microdermabrasion is ideal for hyperpigmentation because the

exfoliation of the epidermis will also remove any excess melanin, a general cause of the condition.

Aging Skin

The normal process of aging can cause mild to sever visual signs on

the skin. Over time, the epidermis and dermis layers of the skin lose

their elasticity and become thinner. The skin also starts to produce

collagen less often. These natural processes most often cause

wrinkles, but can also result in the following skin conditions:

• Age spots

• Hyper-pigmentation

• Spider veins

• Enlarged pores

Changes in the epidermis and dermis are typically based on genetics, but may also be caused by other

factors, such as stress, the environment, smoking, and health issues. The effects of these can break

down the skin’s natural renewal process. Diamond microdermabrasion is effective for treating aging skin.

Mild to moderate signs of aging skin will require a less intense treatment than those that are more severe.

Photoaging

Photoaging refers to a disorder of the skin that results from exposure to ultraviolet radiation (sun rays, for

example). The visual signs of the disorder are very similar to those of aging skin. Both conditions can

cause wrinkles, coarse skin, and fine lines. The main difference in the two conditions is that a chronic

inflammation of the skin is linked to the breakdown of collagen and elastin. In addition, photoaging can

damage DNA and increase an individual‘s risk of developing cancerous skin cells.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Introduction to Diamond Microdermabrasion 7

In mild to moderate levels of photoaging, superficial diamond microdermabrasion can have effective

results. Individuals with advanced or severe levels of photoaging will require treatments that penetrate

more deeply into the skin. While diamond microdermabrasion is safe and effective for treating severe

photaging, more attention is required to prevent scarring.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Chapter 2:

System Details

This chapter describes the 5 in 1 Diamond Dermabrasion system. This system is designed with five functions

that provide safe, non-abrasive, and effective skin resurfacing for the face and body. The system can be used

alone or in association with skin products to restore and produce healthy skin.

System Overview

The system consists of three main areas: connections, the front panel, and accessories (functions).

Connections

The back of the system is where all the system accessories and power cord are connected. The main power

switch for the system is also located in this area. Figure 2 shows the location of all connections on the back of

the system.

Figure 2: System Back View

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 9

Front Panel

The system front panel includes the controls for operating the accessories (functions) included with the

system. Figure 4 shows the location of functions controls on the front panel.

Accessories (Functions)

Figure 3: System Front Panel

The five accessories included with the system are seated in a pocket on the back of the system until use. The

following is a list of the five accessories (Note: The NV-B605 model includes all five functions. See notes

within each section to determine which models apply to the specified function.)

Diamond Dermabrasion

• Skin Scrubber

• Hot & Cold Hammer

• Ultrasonic

• Photon

Diamond Dermabrasion

Diamond Dermabrasion is the main function of the system, and consists of diamond heads that are designed

to resurface the top layer of the skin. Any dead skin or other debris that accumulates during the skin treatment

process is suctioned through vacuuming mechanism. The Diamond Dermabrasion function is suitable for basic

skin care as well as correcting minor skin conditions, such as acne, wrinkles, and skin darkening.

The system Diamond Dermabrasion function includes the following components:

• 9 Diamond tips

• 2 Stainless steel wands

• 1 pack of small cotton filters

• 1 pack of big cotton filters

• 1 PVC hose

• Rubber and rings

• Fuses

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 10

To use the Diamond Dermabrasion function:

1. Connect all associated components:

a. Unscrew the Diamond Vacuum Output socket and ensure a large cotton filter is in the center

and a large black ring is around connector head.

b. Replace the Diamond Vacuum Output socket.

c. Attach one end of the PVC hose to the Diamond Vacuum Output socket.

d. Attach the other end of the PVC hose to the end of the diamond-tipped wand.

e. Ensure a small black ring is around the head of the wand.

f. Place a small cotton filter on the head of wand.

g. Select the appropriate diamond tip size and screw it into the wand. If necessary, refer to Table

1 for recommended diamond tip usage.

2. Connect the plug to the Power Cord connector, plug in, and press the power button.

3. Turn the Vacuum Intensity Knob to the lowest setting.

4. Slowly increase the vacuum intensity to the desired setting (see Table 1 for recommendations). The

Vacuum Meter will display the amount of pressure. In general, the maximum vacuum intensity should

only be used when necessary.

Table 2: Recommended Vacuum Intensity Settings

Treatment Normal Skin (inHg) Sensitive Skin (inHg)

Area

Face 12-22 8-12

Forehead 12-22 10-12

Chest 15-20 15-18

Nose 10-15 10-14

Neck 18-18 10-15

Near Eye Area 8-12 8-10

5. Using a slow sliding motion, move the diamond tipped wand across the skin. Refer to the “Treatment”

section of Chapter 3 of this guide for details about how to use the system to treat specific areas of the

face and body. Important: Do not leave the diamond tip in one area for an extended period of time.

Doing so may damage to the skin.

6. Using your thumb and finger, gently stretch the skin of the treatment area and glide the wand two or

three more times over the area. Note: Crisscrossing your movements is recommended to prevent

streaking. You may use brush strokes or polishing motions in different areas of the skin being treated.

7. When the treatment is complete, use a soft brush to remove any dead skin and rinse the treated area

with a damp sponge or a cool, damp towel.

8. Allow the skin to dry and then apply desired skin product.

9. Use a toothbrush or cotton swab dabbed in alcohol to clean the diamond tip.

10. Sterilize diamond tip with ultraviolet light or high temperature.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 11

Success with treating the skin with the Diamond Dermabrasion function depends on the condition of the skin

and the frequency of treatments. Table 3 shows the recommended treatment schedule for using the Diamond

Dermabrasion function:

Table 3: Diamond Dermabrasion Frequency

Treatment Frequency (days) Total Visits

Face Peeling 6-10 3-5

Fine Lines 7-13 6-8

Neck 12-14 3-5

Acne Scars 7-12 8-10

Hyperpigmentation 7-12 8-10

The Diamond Dermabrasion function includes two stainless steel wands that may be used with nine

interchangeable diamond tips.

Important Notes about the Diamond Tips:

Diamond tips provide finer grit the higher their “D” number. For example, the D100 diamond tip

provides a finer grit than the D80 diamond tip.

• The diamond tips must be sterilized before use. The recommended sterilization process is to first

clean the tips with alcohol, and then by expose them to ultraviolet light or high temperature.

• Replace the large cotton filter, which is located inside the vacuum connector, every five treatments.

• Replace the small cotton filter after each treatment.

The following table shows the diamond tip sizes and their recommended usage:

Diamond Tip#

D80

Table 4: Diamond Tips Recommended Usage

Recommended Usage

Recommended when treating areas of the body, especially the knees and elbows.

Appropriate for treating acne and stretch marks resulting from pregnancy. Can also

be used for treating cellulite

D100, D120

Recommended when treating the face. Suitable for treating large imperfections and

blemishes.

Recommended for treating scars, aging skin, and general imperfections.

D150, D180, D220

Recommended for treating the eye area and the sides of the nose. Suitable for

treating aging skin, photoaging, and acne. Also ideal for treating the eye area.

D160, D180

Smooth Tip

Used to vacuum dead skin and debris.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 12

Skin Scrubber

(Not available with model NV-B601) The Skin Scrubber function uses ultrasonic waves to loosen

dead skin cells, and is ideal for smoothing wrinkles, treating acne, and rejuvenating the skin. This

function also uses heat and vibration for a stimulating massage and to help penetrate skin

products deeper into the skin.

The Skin Scrubber function includes the following components:

• 1 scrubber handle

• 1 negative current handle

To prepare the Skin Scrubber for use:

1. Attach the scrubber handle to the Scrubber Socket and the negative current handle to the Negative

Current outlet (see figures below). Ensure the cover is removed from the scrubber handle prior to use.

connections

negative current handle

scrubber handle

2. Press the Main Power Switch located on the back of the system (see image below).

3. Press the Skin Scrubber timer button located on the system’s front panel (see image below).

4. Using the intensity up and down controls located on the front panel (see image below) set the Skin

Scrubber intensity. Always consider the client’s comfort level. You can increase the intensity as

needed.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 13

5. Press the Scrubber Start/Stop control (see image below). The skin scrubber will start making a low

“ticking” sound.

6. Select a pulse or continuous current Wave setting on the front panel (see image below) that is suitable

for the treatment area and within the client’s comfort level. There is a distinct sound difference

between the pulse and continuous current.

7. Ask the client to hold the negative current handle during the treatment. You will hold the scrubber

handle during the process.

To use the Scrubber to cleanse the skin:

1. Follow steps 1-7 above to prepare the Skin Scrubber for use.

2. Apply your desired cleansing product to the client’s skin.

3. Use the Skin Scrubber to massage the product into the client’s skin.

4. With a slight scraping motion, use the Skin Scrubber (the curved side pointing up at a 45-degree

angle) to remove remaining product from the client’s skin (see image below).

5. Set the continuous current Wave setting.

6. Use a tissue or 4x4-size cotton pad to wipe away any excess product from the client’s skin.

7. Remove any remaining product with sponges, cotton rounds, or a warm towel.

To use the Scrubber for basic skin care:

1. Follow steps 1-7 above for preparing the Skin Scrubber for use.

2. Follow steps 1-5 above for using the Scrubber to cleanse the skin.

3. Apply a serum, cream, or gel that is appropriate for the client’s skin type and skin condition.

4. Set the pulse current Wave setting.

5. Using the small flat side of the Skin Scrubber, glide around the skin to treated area to ensure the

product penetrates deep within the skin.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 14

To use the Hot & Cold Hammer:

Hot & Cold Hammer

(Not available with model NV-B601) The skin will be slightly sensitive after diamond

microdermabrasion. The Cold function is a post-treatment to soothe the skin, while the Hot

function is ideal for maximum absorption.

The Hot & Cold function includes the following component:

• 1 Hot & Cold Hammer

• To use the Hot & Cold Hammer:


1. Clean the head of the Hot & Cold Hammer with alcohol or a disinfectant wipe.

2. Connect the Hot & Cold Hammer to the Hot & Cold socket.

3. Set the Diamond Dermabrasion Super Skin Scrubber Ultrasound timer.

4. Press the Hot & Cold Hammer button to activate the function. The system fan will start to run.

5. To start the Cold function, press the down button (-) on the Hot & Cold hand piece. The metal on the

Cold hammer side will become very cold.

6. To start the Hot function, press the up (o) button on the Hot & Cold hand piece up. The fan speed will

increase. The hammer will become mildly hot.

7. Wait 2-3 minutes to allow the hammer to become “Cold” or “Hot.”

8. Treat the skin area for approximately 5-10 minutes. Do not remain in one area of the skin for an

extended period of time to prevent the Hot or Cold head from causing damage to the skin.

Important Note: Use caution when treating the forehead with the Cold head as some people have

reported headaches.

9. Press the Hot & Cold Hammer button on the front panel to turn off the function.

10. Clean the head of the Hot & Cold Hammer with alcohol or a disinfectant wipe.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 15

Ultrasonic

(Not available with model NV-B601) The Ultrasonic function consists of sonic

vibrations that can operate at 91 megahertz (MHz) and generate one million vibrations

per second. The speed of the vibrations generates frictional heat, which accelerates

blood circulation, relaxes the muscles, and decomposes cellulite. This function is ideal

for stimulating skin tissue and improving its porous nature to promote collagen tissue,

reduce wrinkles and the appearance of fine lines. This function is also ideal for lifting

the skin so it appears more youthful and healthy.

The Ultrasonic function includes the following components:

• 1 Face electrode (flat head)

• 1 Eye electrode (pointed head)

Safety Warnings for the Ultrasonic function:

• Do not treat the eyelids directly. Treat just below the eyebrow and brow bone.

• Do not keep the electrode in one area of the skin. Always keep the electrode moving across the skin.

• Never point the electrode towards the chest area.

• Clean lightly the popping head with cotton. Do not rinse it with water. Be careful not to drop or crash.

• Pregnant, patients with disease of blood vessel, heart, skin, bleeding & trauma are prohibited to use

ultrasonic.

• People with abnormal kidney, liver disease are not suitable for this function.

To use the Ultrasonic function:

1. Cleanse the treatment area and apply a product such as a gel or serum that is suitable for the client’s

skin type and/or condition.

2. Choose the type of electrode suitable for the treatment are:

a. If treating the eye area, use the eye electrode (pointed head)

b. If treating the face and/or neck area, use the face electrode (flat head).

3. Connect the appropriate electrode (face or eye) to one of the Ultrasonic Sockets.

4. Press the Main Power Switch button.

5. Press the Ultrasonic power button located on the front panel.

6. Set the Ultrasonic timer and press the Wrinkle button (if available).

7. Use the Ultrasonic Intensity Up/Down buttons to set the desired intensity. Ultrasonic intensity levels

range from 0-9 (minimum 0 to maximum 1.8 Watts/cm). Each level is 0.2 Watts/cm. The following

table shows the recommended Ultrasonic intensity range according to treatment area:

Table 5: Ultrasonic Recommended Intensity Usage

Treatment aRea Intensity Range

Face 0-4

Body 5-9

8. Press the pulse or continuous Wave control.

9. Press the Ultrasonic Start/Stop button located on the front panel.

10. Ask the client to hold the negative current handle during the treatment. You will hold the electrode

handle (eye or face) during the process.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 16

Photon

(Not available with models NV-B601 and NV-B604) The Photon function uses color (7

available) light wave technology to improve the condition of the skin. This function is

ideal for basic skin care, reducing inflammation, treating skin discoloration, and

accelerating skin cell reproduction.

The Photon function includes the following components:

• 1 Photon probe

• 1 color box

Important Notes about the Photon function:

• Before using the Photon function, choose a color suitable for the condition of the client’s skin. Using

an inappropriate color may irritate the skin and cause redness, especially on sensitive skin. If this

happens, use the cold side of the Hot & Cold Hammer function to soothe the client’s skin. The redness

should disappear within 24 hours.

• You can use the Micro Electric Current control with the Photon function to increase the effectiveness

of the function.

The following table lists the settings available on the Micro Electric Current control. Note: When starting a

treatment, set the Micro Electric Current control to the minimum setting, and then adjust the setting

according to the needs of the client.

Micro Electric Current Control

Table 6: Micro Electric Current Control Settings

WAVE

Two available options: Continuous Wave or Intermittent Wave

MODE/ON

Choose from two available options:

• MODE: Select one of seven colors (refer to Table 7 for the

recommended Photon function color usage).

• ON: Starts the photon function

AUTO

Choose this setting to allow the system to operate the Photon

function automatically and cycle through the seven colors (refer to

Table 7 for the recommended Photon color usage).

OFF

Choose this setting to stop the photon function.

The following table lists the recommended color usage for the Photon function:

Table 7: Recommended Photon Function Color Usage

Photon Skin Depth

Recommended Usage

Color

(1-6)

1-Red 6 Treat aging skin, loosen dead skin, and burn fat

2-Green 4

Dilate capillary vessels, reduce inflammation, lift eyes, remove dark circles

from eyes, and breast lifting

3-Blue 2 Treat acne and reduce inflammation

4-Yellow 5 Generate skin cell reproduction

5-Purple 1 Accelerate skin cell regeneration

6-Cyan 3

7-White 1 and 6 combination Treat hyperpigmentation

Treat skin hypersensitivity and reducing the appearance of capillary

vessels

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 17

Troubleshooting

The diamond microdermabrasion system discussed in this guide is easy to use and should not have any major

problems when used according to the directions provided in this guide. If you experience problems with the

system, check the following list:

The system is not working.

Ensure both main power buttons are turned on.

The system has low suction.

Ensure the top of the metal hand piece is shut.

The system has low vacuum pressure.

• Check that the vacuum hose is connected properly to the system and the hand piece.

• Ensure the vacuum hose is not bent.

• Check to ensure that the rubber O ring in the Diamond pin is secure, as shown in the following image:

• Check to ensure that the rubber O ring in the vacuum socket is secure:

1. Locate the vacuum socket on the back of the system.

2. Remove the vacuum socket cover.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 18

3. Gentle lift the socket to expose the O ring.

The system has no response when the power buttons are turned on.

• Ensure the power cord is properly connected to the system and the power outlet.

• Replace the fuse:

1. Locate the power cord connector located on the back of the system.

2. Press down on the fuse to remove it.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


System Details 19

3. Remove the fuse.

4. Add the replacement fuse.

I’ve tried your suggestion and the system is still not operating properly.

Contact your distributor. Do not make any modifications to the system or open it to inspect.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Chapter 3:

Treatment Instructions

Detailed information for using the diamond microdermabrasion system is

provided in this chapter. The chapter includes the three basic phases of

any operation carried out using the system:

• Pretreatment

• Treatment

• Post-treatment

Pretreatment

The pretreatment phase is very important. Do not overlook the recommended steps for preparing the

system and client for the treatment.

Supplies you will need in addition to the system:

• Towel

• Gentle facial cleanser

• Astringent containing alcohol

• Sunscreen with SPF 15 or higher

• (Optional) Steamer

• Vinyl gloves

• Facemask (for operator)

• (Optional) Eye pads for patient

• User’s Guide

System

The machine must be prepared for each treatment.

1. Make sure the system is properly connected.

2. Cleanse and sterilize the accessories you plan to use during the treatment.

Client

It is very important that the client’s skin is properly prepped for diamond microdermabrasion.

1. Evaluate the client’s skin to determine the function that is most suitable for the area being treated.

If using the Diamond Dermabrasion function, determine the vacuum setting according to the

depth of resurfacing you need to perform on the skin. If this is the client’s first treatment, lower

settings are recommended to determine the skin’s level of tolerance for the treatment.

2. The area to be treated should be cleansed with water and a mild cleanser.

3. The procedure is most effective when the skin is free of any oil. Applying a solution that contains

alcohol will do the trick. For patients with excessively oily skin, a steamer is recommended

4. Dry the skin completely.

5. (Optional) Cover the patient’s eyes.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Treatment Instructions 21

Treatment

This section explains the recommended way to treat the face and body using the system. Repeat the

treatment process no more than twice. The neck area should receive a single pass. Refer to the

accompanying images for assistance.

Treating the Face

When treating the face, it is best to use short cross-hatching or

circular motions, as shown in Figure 4. In a smooth and even

motion, start at the forehead and work downward to the neck.

The skin must come in close contact with the selected

accessory (dermabrasion function) for maximum effectiveness.

Use your finger to stretch the skin to gently pull it close to the

accessory. Keep an eye on how the skin reacts to each motion.

Note: Make two passes when treating the facial area.

The following are recommendations for treating specific area of

the face.

Forehead

Use cross-hatching when treating the forehead area. The ideal

motion is upward strokes that move toward the crown of the

head and cross strokes that move toward the edges of the face.

Eye Area

The same motion used for treating the forehead is

recommended for the eye area. However, use short cross

motions that sweep toward the edges of the face

Figure 4: Sample Face Treatment

Nose

Use straight, even upward strokes when treating the bridge of the nose, and circle motions for the area

just outside the nose.

Mouth Area

Use small cross-hatching motions when treating the mouth area.

Chin

Follow the natural shape of the chin when using small cross-hatching motions in this area.

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Treatment Instructions 22

Treating the Body

Treating the body with diamond microdermabrasion is very similar to treating the face. The ideal is to

follow the natural direction of the body’s natural muscular structure as you move from one area to the

next. Unless treating a specific area of the body, long and straight strokes are best for treating large areas

of the body.

Torso

Starting from the back, use long and straight strokes when treating the torso. Refer to Figure 5 for a

demonstration.

Figure 5: Torso Treatment

Chest

Use long and straight downward strokes to treat the chest area, as shown in Figure 6.

Safety Warning: Never point any of the system accessories directly at the chest.

Figure 6: Chest Treatment

Back

Treating the back is identical to treating the torso, except that you use long and straight strokes that start

from the front of the body. Figure 7 shows the ideal movements.

Figure 7: Back Treatment

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Treatment Instructions 23

Buttocks

Depending on the client, the buttocks can consist of a significant amount of fatty tissue. Several circular

or upward sweeping motions, shown in Figure 8, are recommended for treating this area of the body.

Figure 8: Buttocks Area Treament

Arms and Hands

The recommended flow of movement for the arms hands is to work from just below the nail toward the

shoulder, as shown in Figure 9. Use long and straight strokes when treating the arm area.

Important Note: Do not treat the arm area if there is a significant amount of hair present.

Figure 9: Arms and Hand Treatment

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Treatment Instructions 24

Legs

The legs can vary in muscular composition from one client to the next. Use cross-hatching for softer

areas, such as the inner thigh and the back of the leg. Long and straight strokes are ideal for the sides

and front of the legs. Circular motions are recommended for the back of the calf. Figure 10 and Figure 11

show the ideal flow of motion when treating the legs.

Figure 10: Leg Treatment

Figure 11: Back Leg Treatment

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Treatment Instructions 25

Feet

You use the same motion to treat the feet that you would use to treat the hands. Using strokes that follow

the natural structure of the feet, work from just below the toenail toward the ankles, as shown in

Figure 12.

Figure 12: Feet Treatment

Post-Treatment

Each client is different and will require different post-treatment. The following are some general guidelines

to follow after treating a client’s skin with diamond microdermabrasion:

• After the skin is treated with diamond microdermabrasion, use the Cold Hammer to treat any

temporary redness. A moisturizer or ointment can also help reduce the redness. The redness

should disappear in a couple of days.

• The removal of the epidermis can leave the skin more vulnerable to harsh sunrays. A sunscreen

with a minimum sun protection factor (SPF) of 7 is recommended to protect the skin from

hyperpigmentation.

• The following should be avoided after the skin has been treated with diamond

microdermabrasion:

o

o

o

o

o

Acid skin peeling products

Sun exposure (for at least three days)

Other skin treatments such as hair removal

Medical preparations that exfoliate the skin, such as Retin-A (for at least a week after

treatment)

Heavy cosmetic foundation and/or pressed powder that is applied to the face

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System


Index

A

acne · 5

aging skin · 6

arms and hand treatment · 23

B

back treatment · 22

body treatment · 22

buttocks treatment · 23

C

chest treatment · 22

chin treatment · 21

D

Diamond Dermabrasion function · 9

Diamond Microdermabrasion

uses · 5

E

eye treatment · 21

F

forehead treatment · 21

functions · 9

H

Hot & Cold Hammer function · 14

hyperpigmentation · 6

L

M

mouth treatment · 21

N

neck treatment · 21

nose treatment · 21

P

Photon function · 16

post-treatment · 25

pretreatment · 20

R

Rosacea · 6

S

Skin Scrubber · 12

sun damage · 6

system

diamond tips · 11

technical specifications · 3

using · 20

warnings · 3

T

torso treatment · 22

treatment · 21

troubleshooting · 17

W

warnings · 3

legs and feet treatment · 24

NV-B601NV-B604NV-B605 5 in1 Diamond Dermabrasion System

More magazines by this user