Instruction Manual - GME

gme.net.au

Instruction Manual - GME

SPK001

SPK002

MARINE STEREO 2 WAY

COAXIAL SPEAKERS

Technical specifications & CUTTING TEMPLATE


Mounting instructions

PRECAUTIONS

1 Please avoid contact with inside speaker wire

2 Do not change the polarity of the speaker terminal assembly

CONNECTING

1. Attach the speaker wires (supplied) to the speaker terminals be sure to

connect the striped wire to the negative (–) terminal, and the other wire

to the positive (+) terminal of the speaker.

To Amp

/Stereo

3 Make sure lead and speaker terminals do not contact metal.

4 When making connections, please refer to the instruction manual

of marine stereo used.

MOUNTING

1. When mounting the SPK001 in the kick panel, make sure there

is a clearance of 55 mm (2.17”) behind the well.

When mounting the SPK002 in the kick panel, make sure there

is a clearance of 65 mm (2.56”) behind the well.

SPK001

SPK002


Connect the other end of the speaker wires to your amplifier/stereo.

2. Remove the speaker grille (turn anti-clockwise). Fit the speaker into the

cutout and secure the speaker using the screws (supplied).

Replace the speaker grille on the speaker (turn clockwise) until the grille

locks into place.

(4.8”)

123

(5.7”)

145

55

(2.17”)

65

(2.56”)

2. Push out the template from this leaflet and use to mark the position

of the mounting screws and the outline of the speaker hole. Drill the

mounting holes and cut the hole for the speaker.

PAGE 2 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK001/SPK002


Outer edge of speaker grille (Push out)

Speaker hole (Push out)

Mounting Example

Mounting Template for SPK001

Please push out.

SPK001 TEMPLATE

SPK001/SPK002 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE PAGE 3


SPK001 Cutting Template

PAGE 4 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK001/SPK002


Outer edge of speaker grille (Push out)

Speaker hole (Push out)

Mounting Example

Mounting Template for SPK002

Please push out.

SPK002 TEMPLATE

SPK001/SPK002 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE PAGE 5


SPK002 Cutting Template

PAGE 6 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK001/SPK002


Speaker driver specifications

SPK001

SPK002

System Coaxial woofer/tweeter Coaxial woofer/tweeter

Power (Watts) 110 140

Tweeter Neo PEI Dome Neo PEI Dome

Efficiency (1W/1M) 88 db 89 db

Frequency Response 80 Hz–20 kHz 70 Hz–20 kHz

Impedance (Ohms) 4 4

Weight - kgs, (lbs) 0.78 (1.72) 1.34 (2.95)

Speaker Depth - mm (inches) 55 (2.17) 65 (2.56)

WARRANTY

GME limit this warranty to the original purchaser of the equipment.

GME warrant the SPK001/SPK002 to be free from defects in material

and workmanship for a period of thirty six (36) months from the date of

purchase from their authorised retailer.

Should the product require servicing during this period, all labour and parts

used to effect repairs will be supplied free of charge. GME reserve the right

to determine whether damage has been occasioned by accident, misuse

or improper installation whereby the warranty would be void, including

equipment which has been damaged due to:

(a)

(b)

Incorrect or reverse polarity connection to a battery or power supply

or to an incorrect supply voltage.

Operation without an antenna or by connection to an antenna which

has been incorrectly installed, resulting in damage to the speaker’s

output circuit.

Procedure to be followed by claimant: In the event of a defect

occurring during the warranty period, the original purchaser may return

the defective unit along with suitable proof of purchase date (i.e. receipt,

docket, credit card slip etc.) and a full description of the defect to the

retailer from whom the unit was purchased. All freight charges incurred for

transportation by the retailer or GME are the purchaser’s responsibility.

GME AFTER SALES SERVICE

Your speaker is especially designed for the environment encountered in

land and marine installations. The use of all solid state circuitry, careful

design and rigorous testing, result in high reliability. Should failure occur

however, GME maintain a fully equipped service facility and spare parts

stock to meet the customer’s requirements long after expiry of the

warranty period.

(c)

(d)

Effects of water or moisture penetration.

Non-factory modifications.

SPK001/SPK002 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE PAGE 7


A Division of

www.gme.net.au

Head Office: SYDNEY- Locked Bag 2086, North Ryde N.S.W. 1670, Australia. T: (02) 9844 6666 F: (02) 9844 6600.

Melbourne 7 Micro Circuit, Dandenong South, Vic. 3165 T: (03) 9798 0988 F: (03) 9798 0177

Adelaide 14 Phillips St., Thebarton, S.A. 5031 T: (08) 8234 2633 F: (08) 8234 5138

Perth Unit 1, 10-12 Harvard Way, Canning Vale, W.A. 6155 T: (08) 9455 5744 F: (08) 9455 3110

Brisbane Unit 1, 89-101 Factory Rd., Oxley, Qld. 4075 T: (07) 3278 6444 F: (07) 3278 6555

Sydney Unit B, 22-24 College St., Gladesville, NSW. 2111 T: (02) 9879 8888 F: (02) 9816 4722

Auckland Unit 2, 24 Bishop Dunn Pl., East Tamaki, Manukau N.Z. 2013 T: (09) 274 0955 F: (09) 274 0959

For customers outside Australia and New Zealand, please contact your local GME retailer or email to: export@gme.net.au.

Part Number: 310439 Drawing Number: 44307-3 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK001/SPK002

More magazines by this user
Similar magazines