Series 04 Ku-Band TVRO Antenna

More documents

Recommendations

Info

Troubleshooting and Maintenance Series 04 Ku-Band TVRO Antenna Functional Test(s) DacRemP Graph System Function(s) Selection to use Four Quadrant Tracking. ADMC (Position) Tracking Azimuth Encoder Verification. ADMC (Position) Targeting Sea Trial ADMC (Position) Targeting Tracking Stabilization Side Lobe Plots ADMC (Position) Tracking Targeting Alignment (AZ & EL Trims) ADMC (Position) Targeting Determine Blockage Mapping ADMC (Position) Tracking Unwrap recovery (Limited Az systems only) ADMC (Position) Stabilization Pedestal Gain Verification DISPIVC (Loop Error) Stabilization Home switch (flag) verification (Unlimited DISPV (Ref) Stabilization Az systems only) Remote Tilt Verification DISPV (Ref) Targeting Stabilization Level cage alignment Verification (sensor alignment) DISPV (Ref) Targeting Stabilization Rate Sensor Output Verification DISPW (Rate) Stabilization Level and CL fine balance Verification DISPTC (Drive) Stabilization AZ Friction Torque Test DISPTC (Drive) Stabilization DishScan Drive/Phase DishScan XY Tracking Stabilization 7.3.4. Antenna Loop Error Monitoring The DacRemP DISPIVC graph chart provides a means for monitoring the accumulated velocity errors of the antenna for diagnostic purposes. If this error is excessive, it indicates external forces are acting on the antenna. These forces may be the result of but not restricted to static imbalance, excessive bearing friction, cable binding, or wind loading. If these forces cause the antenna to mispoint by more than 0.5° from the desired position the PCU will flag a “Stab Limit” error. • To view the position error, select the graph chart. 7-4
Series 04 Ku-Band TVRO Antenna Troubleshooting and Maintenance • This chart displays sensed axis errors via three traces, CL (Cross Level), LV (Elevation), and AZ (Azimuth), at a fixed 0.05º/ vertical division. • The normal trace average will plots it’s display ± 3 divisions from the red reference line. Any trace line average plotted above this is of concern and troubleshooting required. The example below shows the forces exerted onto the antenna as a resultant of DishScan Drive. The example below shows the results of various forces put upon antenna. • Cross-Level Axis physically moved CCW (down to the left.) and then CW (up to the right.) Elevation Axis physically moved CW. (reflector slightly pushed up) and then physically moved CCW. (reflector slightly pushed down.) At the end of chart recording shows • DishScan Drive turned Off, notice the lack of accumulated IVC errors. 7-5
Page 1 and 2: INSTALLATION AND OPERATION MANUAL F
Page 4 and 5: Revision History REV ECO# Date Desc
Page 6 and 7: Table of Contents Series 04 Ku-Band
Page 8 and 9: Table of Contents Series 04 Ku-Band
Page 10 and 11: Introduction Series 04 Ku-Band TVRO
Page 12 and 13: Operation Series 04 Ku-Band TVRO An
Page 14 and 15: Basic System Information Series 04
Page 22 and 23: Installation Series 04 Ku-Band TVRO
Page 24 and 25: Installation Series 04 Ku-Band TVRO
Page 26 and 27: Setup Series 04 Ku-Band TVRO Antenn
Page 28 and 29: Setup Series 04 Ku-Band TVRO Antenn
Page 30 and 31: Functional Testing Series 04 Ku-Ban
Page 32 and 33: Troubleshooting and Maintenance Ser
Page 84 and 85:
Troubleshooting and Maintenance Ser
Page 86 and 87:
Specifications Series 04 Ku-Band TV
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Drawings Series 04 Ku-Band TVRO Ant
Page 94:
SINGLE LEVEL MFG BILL OF MATERIAL F
Page 97 and 98:
8 7 6 5 4 3 2 1 NOTES: (UNLESS OTHE
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 107 and 108:
NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 112:
Page 118 and 119:
Page 120:
show all

Series 04 Ku-Band TVRO Antenna

Create successful ePaper yourself

Delete template?

Save as template?