DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

More documents

Recommendations

Info

8. Numerically Inputting the Paper Size 12) • Next input the stitching position [A] at the R side. 40 • The position is automatically calculated (from 1:2:1) [W x 1/4], and the LCD displays [*5. A=02.30]. • To change the input, input the four digits again using the 7 Numerical Keys. However, the input range A is 15 to (W/2 – 1.58) inch. 13) • Press the 9 Set Key once. The LCD displays [*5. B=06.90]. 14) • Next, input the stitching position [B] at the L side. • First calculate this position as follows (from 1:2:1); [W x 3/4] The LCD displays [*5. B=06.90]. *5. B=06.90 A Paper feeding direction F 1 2 3 C 4 5 6 0 7 8 9 B Stitch F 1 2 3 C 4 5 6 0 7 8 9 Paper feeding direction 9 Side R Side R Side L
• To change the input, input the four digits again using the 7 Numerical Keys. However, the input range B = (W/2+1.58) to (W– 0.6) inch and within 13.19 inch. 15) When connected to Duplo trimmer DBM-400T Note If connected to any downstream unit other than DBM- 400T or if not connected to DBM-400T, proceed to 16). • When the 9 Set Key is pressed once, the LCD displays [*5. F=06.67]. “F=6.67” is the final size. • If no changes are required, proceed to 16). • To change the value, input a 4-digit number in the same way using the 7 Numerical Keys and proceed to 16). (For details, refer to the instruction manual for DBM- 400T.) 16) • When the 9 Set Key is pressed, the LCD displays [*5. ? 13.60 x 09.20]. 17) • Perform the final check here. • If OK, press the 9 Set Key and memorize the value. The display will start blinking. • If NG, press the 3 Escape Key to return to the first display (the state when the 1 Select Memory Key was pressed), and the LCD displays [*1. ##.## x ##.##] blinking. Input again. This ends input of paper size. 8. Numerically Inputting the Paper Size *5. F=06.67 *5. ? 13.60X09.20 *1. ##.##X ##.## F 1 2 3 C 4 5 6 0 7 8 9 F F 1 2 3 C 4 5 6 0 7 8 9 1 2 3 C 4 5 6 0 7 8 9 3 F 9 1 2 3 C 4 5 6 0 7 8 9 9 9 41
Page 1 and 2: System 4000 DYNAMIC BOOKLET MAKER D
Page 3 and 4: INTRODUCTION Thank you for purchasi
Page 5 and 6: CAUTIONS: Do not use flammable spra
Page 7 and 8: 2. Usage Precautions 2-1. Power Sup
Page 9 and 10: 1 Entrance Section 3-2. Internal Pa
Page 11 and 12: 3 Folding Section ep 3. Names and F
Page 13 and 14: Control Panel 2 1 Lamps/Displays 1
Page 15 and 16: Operation Keys Display Function bmS
Page 17 and 18: No. Name Function 1 2 3 4 5 6 7 8 9
Page 19 and 20: 4. Insert the wire from the 2 Upper
Page 21 and 22: 1. Rotate the 8 triangular knob to
Page 23 and 24: 5. Stitching Range Stitching Positi
Page 25 and 26: 6. Stitching Normal Size Paper Do n
Page 27 and 28: 6.Stitching Normal Size Paper 5. Ad
Page 29 and 30: 6-1-4 Points to remember when paper
Page 31 and 32: 6. Stitching Normal Size Paper 6-2.
Page 33 and 34: 4) • The unit selected at 3) will
Page 35 and 36: 6-6. After Starting To finely adjus
Page 37 and 38: 7. Memorizing • The bs Memory Inp
Page 39 and 40: 5) • Press bl Select Fold Key and
Page 41: 10) • Input the length [S] from t
Page 45 and 46: 8) • Using the 7 Numerical Keys,
Page 47 and 48: When Corner-Stitching at Right Side
Page 49 and 50: 8-4. No-Stitching No-Folding Use th
Page 51 and 52: 2 Attaching Conditions A m ? Attach
Page 53 and 54: If the paper skews immediately afte
Page 55 and 56: 5 Loosen the knob screw at (D), and
Page 57 and 58: 9-8. Using the Guides After Folding
Page 59 and 60: 3 Adjusting the press rollers 3 lev
Page 61 and 62: 10. Using Function Keys Operating t
Page 63 and 64: • Pressing 7 of the 7 Numerical K
Page 65 and 66: 12. LCD Error Messages and Correspo
Page 67 and 68: • Display when the paper jam has
Page 69 and 70: 13. The Unit will Stop in These Cas
Page 71 and 72: 15. Maintenance of the Stitching He
Page 73 and 74: This page is a blank page.
Page 75 and 76: This page is a blank page.

DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?