Training, Installation & Service Manual - Livewire Connections Ltd

More documents

Recommendations

Info

Removal and replacement of ADU modules 2. Adjust the belt tension using the belt-tension adjustment screw. Figure 9-56: Azimuth Encoder, adjust belt tension The tension of the belt is 90-100 Hz on average (use an Optibel frequency measuring device or alike). 3. Tighten the belt tension device by tightening the 4x4 mm Allen screws. Figure 9-57: Azimuth motor, tighten the belt tensioner 4. Check the tension of the belt again (90-100 Hz). If needed, repeat the tension adjustment. 9-48 Chapter 9: Service & maintenance 98-133966-E2
9.5.7.7 Removing the X Elevation Motor and Encoder To remove the Cross Elevation Motor and Encoder, do as follows: 1. Open the service hatch by releasing the two latches. 2. Switch off the power to the antenna on the service switch. 3. Rotate the antenna dish to top position. 4. Rotate the antenna pedestal so that the arm with the GPS module faces the service hatch. 5. Press in and turn the elevation locking pin (only available from serial number TBD) to locked position. 6. Disconnect the 3 cables at the top of the Cross Elevation DDM. Removal and replacement of ADU modules Tools needed: • 4 x 150 mm Allen key (located inside the service door of the ADU) • Acoustic frequency meter 9999 Figure 9-58: Replacement of X-Elevation Motor & Encoder 1 7. Loosen the Cross-Elevation Drive belt tension/adjustment screw. Service & maintenance 98-133966-E2 Chapter 9: Service & maintenance 9-49
Page 1:
TRAINING, INSTALLATION & SERVICE MA
Page 4 and 5:
Disclaimer Any responsibility or li
Page 6 and 7:
Compass Safe Distance: SAILOR 900 V
Page 8 and 9:
vi 98-133966-E2
Page 10 and 11:
Table of contents Chapter 3 Install
Page 12 and 13:
Table of contents 6.2 Calibration o
Page 14 and 15:
Table of contents Appendix A Append
Page 16 and 17:
Table of contents F.4 Alternative g
Page 18 and 19:
List of figures Figure 3-22: ADU, b
Page 20 and 21:
List of figures Chapter 7 Installat
Page 22 and 23:
List of figures Figure 9-68: Polari
Page 24 and 25:
List of figures Figure C-5: Satelli
Page 26 and 27:
List of tables Table 6-3: Possible
Page 28 and 29:
List of tables xxvi 98-133966-E2
Page 30 and 31:
Software version 1.3 Software versi
Page 32 and 33:
Precautions 1-4 Chapter 1: About th
Page 34 and 35:
SAILOR 900 VSAT system The followin
Page 36 and 37:
SAILOR 900 VSAT system 2.1.2 Above
Page 38 and 39:
SAILOR 900 VSAT system 9. Polarisat
Page 40 and 41:
SAILOR 900 VSAT system 2.1.3 Antenn
Page 42 and 43:
SAILOR 900 VSAT system 2.1.3.3 Serv
Page 44 and 45:
Part numbers and options 2-12 Chapt
Page 46 and 47:
Unpacking 3.1.1.3 ACU (19” rack v
Page 48 and 49:
Site preparation 3.2.2 Obstructions
Page 50 and 51:
Site preparation zones (RX and TX)
Page 52 and 53:
Site preparation 3.2.6 ADU mast des
Page 54 and 55:
Site preparation 3.2.6.2 Mast lengt
Page 56 and 57:
Site preparation Mast with 2 braces
Page 58 and 59:
Site preparation Radar Min. 15° Mi
Page 60 and 61:
Site preparation 3.2.7.4 GPS receiv
Page 62 and 63:
Installation of the ADU 3.3 Install
Page 64 and 65:
Installation of the ADU 4. Attach a
Page 66 and 67:
Installation of the ADU Otherwise,
Page 68 and 69:
Installation of the ADU Figure 3-22
Page 70 and 71:
Installation of the ACU (bulkhead)
Page 72 and 73:
Installation of the ACU (bulkhead)
Page 74 and 75:
Installation of the 19” rack vers
Page 76 and 77:
Installation of the VMU 3.6 Install
Page 78 and 79:
Installing the dual-antenna mode (o
Page 80 and 81:
Interfaces of the SAILOR 900 VSAT A
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Interfaces of the VMU 4.2.2 Connect
Page 90 and 91:
Interfaces of the VMU 4.2.5 Connect
Page 92 and 93:
Power cable selection 5.2 Power cab
Page 94 and 95:
Connecting power For other cable ty
Page 96 and 97:
Power up 5.4.0.1 Initialisation in
Page 98 and 99:
Introduction to the built-in web in
Page 100 and 101:
Calibration of the SAILOR 900 VSAT
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Configuration with the web interfac
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Keypad and menus of the ACU After 1
Page 148 and 149:
Keypad and menus of the ACU 6.4.3.1
Page 150 and 151:
Keypad and menus of the ACU SATELLI
Page 152 and 153:
SNMP support 6-56 Chapter 6: Config
Page 154 and 155:
Installation check list: Antenna St
Page 156 and 157:
Installation check list: ACU, conne
Page 158 and 159: Installation check list: Functional
Page 160 and 161: SAILOR 900 VSAT Viewing system para
Page 162 and 163: Getting support: Helpdesk 9.1 Getti
Page 164 and 165: Getting support: Helpdesk 9.1.1.4 S
Page 166 and 167: Software update Note that the uploa
Page 168 and 169: Status signalling with LEDs and sta
Page 170 and 171: Status signalling with LEDs and sta
Page 172 and 173: Removal and replacement of ADU modu
Page 250 and 251: Updating VIM/PCM calibration data F
Page 252 and 253: Troubleshooting 9.7.4 Troubleshooti
Page 255: Appendices
Page 258 and 259:
SAILOR 900 VSAT system components A
Page 260 and 261:
SAILOR 900 VSAT system components A
Page 262 and 263:
Outline drawings A.2 Outline drawin
Page 264 and 265:
Outline drawings A.2.3 ACU, 19 inch
Page 266 and 267:
VSAT LNB Data Sheet (physical LNB)
Page 268 and 269:
VSAT 8 W BUC Data Sheet (Extended)
Page 270 and 271:
Modem Cable Comtech Serial & RSSI T
Page 272 and 273:
Modem Cable iNIFINITI iDirect VSAT
Page 274 and 275:
Open AMIP setup for iDirect INFINIT
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Non-Open-AMIP setup for iDirect iNF
Page 284 and 285:
Non-Open-AMIP setup for iDirect iNF
Page 286 and 287:
Comtech 570L, ROSS box & ACU C.3 Co
Page 288 and 289:
STM SatLink 2900 VSAT modem To disp
Page 290 and 291:
Gilat SkyEdge II VSAT modem Paramet
Page 292 and 293:
Introduction D.1.1 Telnet connectio
Page 294 and 295:
Supported commands D.2 Supported co
Page 296 and 297:
Supported commands Command help tra
Page 298 and 299:
Supported commands Command satellit
Page 300 and 301:
Supported commands Command system r
Page 302 and 303:
Supported commands D-12 Chapter D:
Page 304 and 305:
VSAT coverage Satellite name Satell
Page 306 and 307:
Grounding Recommendations F.2 Groun
Page 308 and 309:
Grounding Recommendations It is alw
Page 310 and 311:
Alternative grounding for steel hul
Page 312 and 313:
Alternative grounding for aluminum
Page 314 and 315:
Alternative grounding for fibre gla
Page 316 and 317:
Separate ground cable F.6.2 Ground
Page 318 and 319:
Jumper cable for grounding F.7 Jump
Page 320 and 321:
RF interference F-16 Chapter F: Gro
Page 322 and 323:
List of ADU events G.2 List of ADU
Page 324 and 325:
List of ADU events Error code (ID)
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
List of ACU events Error code (ID)
Page 332 and 333:
List of ACU events Error code (ID)
Page 334 and 335:
CE (R&TTE) H-2 Appendix H: Approval
Page 336 and 337:
Glossary ETSI European Telecommunic
Page 338 and 339:
Glossary RSSI Received Signal Stren
Page 340 and 341:
Index browser settings for web inte
Page 342 and 343:
Index F factory default calibration
Page 344 and 345:
Index OpenAMIP setup, C-2 supported
Page 346:
Index symbol rate DVB, azimuth cali
show all

Training, Installation & Service Manual - Livewire Connections Ltd

Create successful ePaper yourself

Delete template?

Save as template?