buildex - Triangle Fastener

TABLE OF CONTENTS - A TO I
Abrasive Saw Wheels and Grinding 277-281
Access Doors . . . . . . . . . . . . . . . . . 375-377
Accuseam. . . . . . . . . . . . . . . . . . . . . . . . . 55
AccuTrac. . . . . . . . . . . . . . . . . . . . . . . . . . 55
Acoustical Tie Wires . . . . . . . . . . . . . . . . . 88
Adhesives - Spray. . . . . . . . . . . . . . . . . . 356
A
ANCHORS Light Duty
Expansion . . . . . . . . . . . . . . . . . . . 94-95
Fiber Plug . . . . . . . . . . . . . . . . . . 94, 186
Lead . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Plastic . . . . . . . . . . . . . . . . . . 94-96, 187
Plastic Drive Pin . . . . . . . . . . . . . . . . 185
Wall Dog . . . . . . . . . . . . . . . . . . . . . . . 95
Anchor Bolts . . . . . . . . . . . . . . . . . . . . . . 126
Arrow Staplers . . . . . . . . . . . . . . . . . . . . . 49
Atlas Fasteners - Flat Top . . . . . . . . . . . . 22
AUTOTRAXX / UNIDEK / FASTRAXX
Metal Deck Tool . . . . . . . . . . . . . . . . . . . . 60
Back Support Belts . . . . . . . . . . . . . . . . . 371
Band Saw Blades . . . . . . . . . . . . . . . . . . 287
Bang-It Insert . . . . . . . . . . . . . . . . . . . . . 146
BASE PLY Fastening Patterns . . . . . . . . . 71
BASE PLY FM90, FM75, TWINLOK,
LOC-NAIL, NAIL-TITE, DO-ALL . . . . . 65-71
Batten Strip . . . . . . . . . . . . . . . . . . . . . . . . 56
Beam Clamps . . . . . . . . . . . . . . . . . 119-125
Bit Holders . . . . . . . . . . . . . . . . . . . . . . . 251
BLAZER Self-Drilling Fasteners . . . . . . 9-12
BLAZER ULTRA BSTEEL FRAME
FASTENERS . . . . . . . . . . . . . . . . . . . . . 87
B-Line Fasteners . . . . . . . . . . . . . . . 121-125
BLOCK PLUG Anchors. . . . . . . . . . . . . . 177
Bolts. . . . . . . . . . . . . . . . . . . . . . . . . 189-190
Bonded Washer . . . . . . . . . . . . . . . . . . . 194
Boxes - Jobsite. . . . . . . . . . . . . . . . . . . . 374
BRACER Hillside Washer . . . . . . . . 197-198
BRACE - X Stud/Cable Bracing . . . . . . . 198
Bridal Rings . . . . . . . . . . . . . . . . . . . . . . 125
Bridge Deck Fastener. . . . . . . . . . . . . . . . 62
Brooms . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Brushes - Paint / Rollers. . . . . . . . . . . . . 308
Buildex Roofing Screws - ROOFGRIP /
HEXTRA . . . . . . . . . . . . . . . . . . . . 53-54
Buildex Self-Drilling Fasteners . . . . . . 16-20
ButtonKap Nails . . . . . . . . . . . . . . . . . . . . 45
Butyl Tape - Metal Panels . . . . . . . . 345-346
Cabinet Screws . . . . . . . . . . . . . . . . . . 33-35
Cable Bracing . . . . . . . . . . . . . . . . . . . . . 198
Cable Cutters . . . . . . . . . . . . . . . . . . . . . 321
Cable Grips - Dead Ends, BRACE GRIP 198
C
Cable Ties. . . . . . . . . . . . . . . . . . . . . . . . 196
Cap Head Fasteners (SCOTS) . . . . . . . . 19
Cap Nails - SIMPLEX . . . . . . . . . . . . . 81-82
Cap Screws . . . . . . . . . . . . . . . . . . . . . . 190
Caps for Screw Heads - Plastic . . . . . . . . 30
Caps for Screw Tips - Rubber . . . . . . . . 195
Capsule Anchors . . . . . . . . . . . . . . . 173-174
Carriage Bolts. . . . . . . . . . . . . . . . . . . . . 190
Carts - Drywall . . . . . . . . . . . . . . . . . . . . 318
Cast-In-Place Anchor . . . . . . . . . . . . . . . 146
Caulking Gun (Manual). . . . . . . . . . . . . . 344
(Battery) . . . . . . . . . . . . . . . . . . . . . . 244
Ceiling Clips . . . . . . . . . . . . . . . . 88,110-111
Ceiling Clips - Powder Actuated. . . . 110-111
Ceiling Clips - Tie Wire . . . . . . . . . . . . . . . 88
Cement Board Screws . . . . . . . . . . . . . . 104
Chalk Reel - Marking Tools and Refill . . 319
Chisels. . . . . . . . . . . . . . . . . . . . . . . 267-268
Chisels - Cold Hand . . . . . . . . . . . . . . . . 297
Clamps - Locking . . . . . . . . . . . . . . . . . . 292
CLIMASEAL Long Life Coating . . . . . . . . 63
Clips - Powder CActuated . . . . . . . . . . . . . 111
Closure - Metal Panel / Foam . . . . . . . . 331
Closure - UNIVERSAL CLOSURE . . . . . 332
Collated Screws . . . . . . . . . . . . . . . . . 37-38
COLORFIXX / COLORHEXX
Nylon Head Fasteners . . . . . . . . . . . . 30
Composite Deck . . . . . . . . . . . . . . . . . . . . 31
Compressors . . . . . . . . . . . . . . . . . . . . . 222
CONCEALOR Pancake Head. . . . . . . 13-15
Concrete Fastening Systems - Overview of
Products. . . . . . . . . . . . . . . . . . . 131-132
Conduit Clips . . . . . . . . . . . . . . . . . . 121-122
Coolers - IGLOO. . . . . . . . . . . . . . . . . . . 378
Coring Bits . . . . . . . . . . . . . . . . . . . . . . . 284
Corrosion Resistant Screws . . . . . . . . . . . 11
Coupling Nuts . . . . . . . . . . . . . . . . . . . . . 192
Cutter Bits - Rotary . . . . . . . . . . . . . 269-270
Cutting Fluid and Oil. . . . . . . . . . . . . . . . 358
DECK-IT Wood Deck Screws. . . . . . . . . . 31
DEC-KING Exterior Wood Screws . . . . . . 32
Deck Screws (Wood) . . . . . . . . . . . . . . . . 31
DEC-U-DRIVE Stand-Up Tool . . . . . . . . . 32
DEK-CAP - Metal Roofing End Cap
Flashing. . . . . . . . . . . . . . . . . . . . . . . 330
Dekstrip. . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Diamond Coring Bits - Concrete. . . . . . . 284
DIAMOND PRODUCTS D. . . . . . . . . 282-284
Diamond Sawing Blades - Concrete 282-283
Diaphragm Screw - Post Frame. . . . . . . . 28
Dow Insta Stick, Foam & Tile Bond. . . 75-79
Drains - Roof . . . . . . . . . . . . . . . . . . . . . 335
Drill Bit Sizes . . . . . . . . . . . . . . . . . . 261-262
Drill Bits - Carbide . . . . . . . . . . . . . . 263-266
Drill Bits - High Speed Steel . . . . . . 257-260
Drill Bits - Wood Boring . . . . . . . . . . . . . 290
Drills - Step . . . . . . . . . . . . . . . . . . . . . . . 289
Drop-In Anchor . . . . . . . . . . . . . . . . 143-145
Drywall Fasteners . . . . . . . . . . . . . . . . 83-84
Duck Bill Pliers . . . . . . . . . . . . . . . . . . . . 292
DYNABOLT Sleeve Anchors . . . . . . 135-138
Ear Protection. . . . . . . . . . . . . . . . . . . . . 368
E
EIFS Fastening Systems. . . . . . . . . . 99-103
End Cap Flashing - Metal Roof
Dek Caps . . . . . . . . . . . . . . . . . . . . . 330
EPCON A7 Acrylic Adhesive . . . . . . 147-154
EPCON C6 Fast Curing Epoxy . . . . 155-160
EPCON G5 Extended Working
Time Epoxy . . . . . . . . . . . . . . . . 161-166
EPCON Umbrella Inserts . . . . . . . . 167-169
ES Products . . E. . . . . . . . . . . . . . . . . . 65-71
ET&F Pneumatic Tools . . . . . . . . . . . . . . 254
Explosion Venting Fasteners . . . . . . . . . . 42
Extension Cords . . . . . . . . . . . . . . . 255-256
Extension Poles - Powder Actuated Tools 89
Eyebolts . . . . . . . . . . . . . . . . . . . . . . . . . 198
EZ Products - Anchors . . . . . . . . . . . . . . . 93
EZ Products - Drywall Hangers . . . . . . . . 93
Fabco REZTITE STEEL FRAME
FASTENERS . . . . . . . . . . . . . . . . . 23
FABLOK Rivets. . . . . . . . . . . . . . . . . . . . . 41
Fall Protection . . . . . . . . . . . . . . . . . 371-373
Fastener Index . . . . . . . . . . . . . . . . . . . . 7-8
FIBERPLUG . . . . . . . . . . . . . . . . . . . . . . 186
Finish Nailer . . F. . . . . . . . . . . . . . . . . . 47-48
Firestop . . . . . . . . . . . . . . . . . . . . . . 351-352
First Aid Kits . . . . . . . . . . . . . . . . . . . . . . 369
Fish Tapes . . . . . . . . . . . . . . . . . . . . . . . 321
Flashing - End Cap Metal
Roof (DEK-CAP) . . . . . . . . . . . . . . . . 330
Flashing - Linear EPDM . . . . . . . . . . . . . . 57
Framing Fasteners . . . . . . . . . . . . . . . . . . 24
Framing Nailer . . . . . . . . . . . . . . . . . . . . . 47
Framing Screws . . . . . . . . . . . . . . . . . . . . 87
FROTH-PAK Spray Insulation . . . . . . . . . 78
Furniture Screws . . . . . . . . . . . . . . . . . 33-35
Galvanizing Spray. . . . . . . . . . . . . . . . . . 354
Gas Cans . . . G. . . . . . . . . . . . . . . . . . . . . 379
GEARLOK Roofing Plates . . . . . . . . . . . . 55
Generators . . . . . . . . . . . . . . . . . . . . . . . 235
Gloves. . . . . . . . . . . . . . . . . . . . . . . . . . . 370
GRID MASTER . . . . . . . . . . . . . . . . . 99-103
GRID MATE Plates and Fasteners. . . . . 103
Grommet Seal Rivets . . . . . . . . . . . . . . . . 42
GYPFAST . . . . . . . . . . . . . . . . . . . . . 99-102
Hammers . . . . . . . . . . . . . . . . . . . . . . . . 298
Hand Cleaner . . . . . . . . . . . . . . . . . . . . . 380
Hanger Studs . . . . . . . . . . . . . . . . . . . . . . 36
Hard Hats . . . H. . . . . . . . . . . . . . . . . . . . . 366
Heat Welding Tool . . . . . . . . . . . . . . . . . . 74
Heavy Gauge Drill Screws . . . . . . . . . 10, 16
Hextra . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Hillside Washer. . . . . . . . . . . . . . . . . . . . 197
Hole Accessories - Hole Plugs / Brushes /
Tubing . . . . . . . . . . . . . . . . . . . . . . . . 176
Hole Saw Kits . . . . . . . . . . . . . . . . . . . . . 288
Hole Saws - Steel and Carbide . . . . 271-272
ICH TRAXX Self-Drilling IFasteners . . . . . 62
Insert Drive Bits . . . . . . . . . . . . . . . . 251-253
Installation Tools . . . . . . . . . . . . . . . . . . . . 91
Installation Tools (EFIS) . . . . . . . . . . . . . . 99
INSTA-STICK Roofing Adhesive . . . . . 75-76
Insulation Board
(Rigid) Fasteners . . . . . . . . . . . . . . 17
(Rigid) Plates . . . . . . . . . . . . . . . . . 56
(800) 486-1832 www.trianglefastener.com 2

TABLE OF CONTENTS - J TO SL
J-CLIP and J-MASTER Tools . . . . . . . . . . 90
Jobsite Boxes . . . . . . . . . . . . . . . . . . . . . 374
J
K
LADD Overhead Fastening System . . . . 106
Ladders . . . . . . . . . . . . . . . . . . . . . . 313-314
Lag Screws. . . . . . . . . . . . . . . . . . . . . . . 191
Lag Shield Insert. . . . . . . . . . . . . . . . . . . . 36
LAGMASTER Installation Tool . . . . . . . . . 91
Lanyards. . . . . . . . . . . . . . . . . . . . . . . . . 372
Lasers . . . . . . . . . . . . . . . . . . . . . . . 303-305
Lead Anchors . . L. . . . . . . . . . . . . . . . . . . 186
Lead Concrete Anchors . . . . . . . . . . . . . . 94
Lead, Plastic, FIBERPLUG. . . . . . . . . . . . 94
LEISTER Heat Welding Seaming Tool . . . 74
Leland Fasteners . . . . . . . . . . . . . . . . . . . 29
Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Lifts - Drywall . . . . . . . . . . . . . . . . . . . . . 318
Lightweight Deck Fasteners - Toggle Bolts /
NTB/NC Fasteners. . . . . . . . . . . . . 72-73
Line - Poly. . . . . . . . . . . . . . . . . . . . . . . . 321
Loads - Powder Actuated . . . . . . . . . . . . 112
Locking Pliers - VICE GRIP . . . . . . . . . . 292
Low Profile Head Fasteners . . . . . . . . 13-14
Lubricant - CROWN / WD40 . . . . 354 & 357
KALIDA-KOTE Touch-Up Paint . . . . . . . 353
Knives - Utility / CASE. . . . . . . . . . . 309-312
Knockout Punches . . . . . . . . . . . . . . . . . 320
Machine Screws . . . . . . . . . . . . . . . . . . . 188
Magnetic Bit Holders M. . . . . . . . . . . . 251-253
Measuring Tapes - 100ft to 300ft . . . . . . 306
Measuring Tapes - 25ft . . . . . . . . . . . . . . 301
Metal Decking Fastening Tools . . . . . . 58-61
Metal to Wood Fasteners (Panel-Tite) 27-28
Mounting Brackets - Conduit / Box /
Rod and Wire / Strap . . . . . . . . . 121-125
MULTI-SETT II Drop-In Anchors . . . 143-146
Nails. . . . . . . . . . . . . . . . . . . . . . . . . . . 45-48
Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Nailers - DEWALT. . . . . . . . . . . . . . . . . . 225
Nailers - ET&F Heavy Steel Tool . . . . . . 254
Nailers - PASLODE / SENCO . . . . . . . 47-49
Nail-in Drive Pin Anchors . . . . . . . . . . . . 185
NC Fasteners . . . . . . . . . . . . . . . . . . . . . . 73
NPC SOLAR SEAL. . . . . . . . . . . . . . . . . 338
NTB Fasteners . . . . . . . . . . . . . . . . . . . . . 72
N-O
Nut Drivers - Hand . . . . . . . . . . . . . . . . . 294
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . 191-192
Nutsetter . . . . . . . . . . . . . . . . . . . . . . . . . 251
Nylon Head Fasteners . . . . . . . . . . . . . . . 30
ONE-STEPPER Plastic Panel Fasteners. 29
Paint - KALIDA-KOTE Touch-Up Paint. . 353
Paint - Marking Spray . . . . . . . . . . . . . . . 355
Painted Fasteners . . . . . . . . . . . . . . . . . 353
Pan American Fasteners . . . . . . . . . . . . . 33
Pancake Head Fasteners . . . . . . . . . . 13-15
PANEL-TITE Post Frame Fasteners. . 27-28
Paslode - Nail Tool . . . . . . . . . . . . . . . 47-48
Peel & Seal. . . . . . . . . . . . . . . . . . . . . . . 350
Pins - Powder Actuated . . . . . . . . . . 108-111
Pins and Fuel - TRAKFAST . . . . . . . . . . . 86
Pipe Benders . . . . . . . . . . . . . . . . . . . . . 320
Pipe Flashing - PIPEMASTER . . . . 325-327
PIPEMASTER - Pipe Flashing . . . . 325-327
Plastic Cap Nails . . . . . . . . . . . . . . . . . . . 45
Plastic Expansion Anchors . . . . . . . . . . . . 96
Plastic Light Duty Anchors . . . . . . . . . . . . 94
Plastic Lightweight Anchor and
Fluted Anchor . . . . . . . . . . . . . . . . . . 187
Plates
Roofing . . . . . . . . . . . . . . . . . . . . . . . . 56
Platforms / Scaffolding . . . . . . . . . . 315-318
Plumb Bob - Laser . . . . . . . . . . . . . . . . . 306
Pneumatic Tools P. . . . . . . . . . . . . . . . . . . 254
POLLY / Expansion Anchors . . . . . . . . . . 95
POP TOGGLE Drywall Anchors . . . . . . . . 96
Post Frame Screws (Panel-Tite) . . . . . . . 27
Powder Actuated Pins / Loads /
Ceiling Clips . . . . . . . . . . . . . . . . 108-114
Powder Actuated Pins and
Loads (Decking) . . . . . . . . . . . . . . . . . 61
Powder Actuated Tools
Pins & Loads . . . . . . . . . . . . . . . 105-107
Power Cords . . . . . . . . . . . . . . . . . . 255-256
Powered Bits . . . . . . . . . . . . . . . . . . . . . 251
Power Tools - BOSCH. . . . . . . . . . . 201-207
Power Tools - DEWALT. . . . . . . . . . 208-225
Power Tools - FEIN. . . . . . . . . . . . . . . . . 228
Power Tools - KETT . . . . . . . . . . . . 226-228
Power Tools - MAKITA . . . . . . . . . . 229-236
Power Tools - METABO . . . . . . . . . 237-238
Power Tools - MILWAUKEE . . . . . . 239-248
Power Tools - Power Cutters . . . . . . . . . 236
Pre-Tired Wires - TWISTER . . . . . . . . . . . 88
PROFILE VENT Roof Venting
Closure. . . . . . . . . . . . . . . . . . . . 333-334
Pry Bars . . . . . . . . . . . . . . . . . . . . . . . . . 297
Pullout Testing . . . . . . . . . . . . . . . . . . . . . 80
Pullout Testing Tool. . . . . . . . . . . . . . . . . 322
Punches - Knockout . . . . . . . . . . . . . . . . 320
Purlin Clips . . . . . . . . . . . . . . . . . . . . . 88-89
Quick Drive Fasteners and Tools . . . . 37-38
Q-R
Rags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Ramset Trakfast . . . . . . . . . . . . . . . . . 85-86
Rebar Cutting Bits . . . . . . . . . . . . . . . . . 270
Reciprocating Saw Blades . . . . . . . 285-286
REDI-BOLT Sleeve Anchors . . . . . . 133-134
Respirators . . . . . . . . . . . . . . . . . . . . . . . 369
Retrofit Pipe Flashing . . . . . . . . . . . . . . . 326
REZTITE Steel Frame Fasteners . . . . . . . 23
Rivet Installation Tools . . . . . . . . . . . . . . . 40
Rivets - Blind . . . . . . . . . . . . . . . . . . . . . . 39
Rivets - Bulb-Tite . . . . . . . . . . . . . . . . . . . 43
Rivets - FABLOK . . . . . . . . . . . . . . . . . . . 41
Rivets - Grommet RSeal . . . . . . . . . . . . . . . 42
Rivets - Painted . . . . . . . . . . . . . . . . . . . . 39
ROCK-ON Cement Board Fasteners . . . 104
Rollers - Paint Rollers / Frames /
Handles . . . . . . . . . . . . . . . . . . . . . . 308
Roof Grip . . . . . . . . . . . . . . . . . . . . . . . . . 54
Roof Screw Plates . . . . . . . . . . . . . . . . . . 50
Roof Venting - PROFILE VENT . . . 333-334
Roofing Screws - Technical Data . . . . . . . 52
Roofing Screws (BUR) . . . . . . . . . . . . 50-63
Roofing Tools. . . . . . . . . . . . . . . . . . . . 57-60
Safety Equipment - Roofers Kit . . . . . . . 373
Safety Glasses . . . . . . . . . . . . . . . . . . . . 367
Safety Harness . . . . . . . . . . . . . . . . . . . . 371
SAMMY SUPER SCREWS . . . . . . . . . . . 92
Saw Blades - Band Saw. . . . . . . . . . . . . 287
Saw Blades - Circular . . . . . . . . . . . 273-276
Saw Blades - Reciprocating . . . . . . 285-287
Scaffolding / Platforms . . . . . . . . . . 315-318
SCOTS Stainless Cap Head Fasteners . . 19
Screw Drivers - Hand . . . . . . . . . . . 293-294
Screw Drivers - Torx Drive . . . . . . . . . . . 294
Screw Driving Insert Bits . . . . . . . . . . . . 251
Screw Tip Caps . . . . . . . . . . . . . . . . . . . 195
ScruBolt . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SEALANTS
NPC - Solar Seal. . . . . . . . . . . . . . . . . 337
SIKA-Butyl, Polyurethane, Butyl Tape. 343
SCHNEE-MOREHEAD - Butyl,Silicone,
Polyurethane, Self-Leveling . . . . . 338-340
SONNEBORN - Polyurethane. . . . . . . 342
SUREBOND - SAdhesive, Siliconized
Rubber. . . . . . . . . . . . . . . . . . . . . . . . . 341
TFC 100,116 - Polyurethane Sealant . 336
TREMCO - Silicon, Polyurethane,
Pourable. . . . . . . . . . . . . . . . . . . . 347-348
Seaming Tool - Heat Welding. . . . . . . . . . 74
Security Screws . . . . . . . . . . . . . . . . . . . . 44
Self-Drilling Carbon Fasteners . . . . . . . 9-10
Self-Drilling Drywall Fasteners . . . . . . . . . 84
Self-Drilling Framing Fasteners . . . . . . . . 87
Self-Drilling Large Diameter Fasteners . . 23
Self-Drilling Stainless Steel Fasteners . . . 11
Self-Drilling Technical Data. . . . . . . . . . . . 12
Self-Drilling Torx Drive Fasteners. . . . . . . 87
Self-Sealing Fasteners . . . . . . . . . . . . . . . . 9
Self-Sealing Fasteners (Maxiseal) . . . . . . 18
SELF-TAPPING Carbon and
Stainless Fasteners . . . . . . . . . . . . 25-26
SENCO Staplers . . . . . . . . . . . . . . . . . . . . 49
SENTRY PLUS FIVE Roofing Screws 50-52
Sheet Metal Screws - HWH / Pan Head . 36
Sheet Steel Tolerances. . . . . . . . . . . . . . 400
Sheeting Screws . . . . . . . . . . . . . . . . . 25-26
Shovels . . . . . . . . . . . . . . . . . . . . . . 299-300
SIMPLEX Roofing Nails . . . . . . . . . . . . . . 82
Sledge Hammers . . . . . . . . . . . . . . . . . . 298
Sleeve Anchor . . . . . . . . . . . . . . . . . 133-138
3
TRIANGLE FASTENER CORPORATION

TABLE OF CONTENTS - SN TO Z
Snips - Hand. . . . . . . . . . . . . . . . . . . . . . 291
Sockets - Impact and Standard . . . . . . . 295
Solvent . . . . . . . . . . . . . . . . . . . . . . . . . . 354
SPAN-MASTER STEEL Deck Screw. . . . 62
SPEED-LOK Toggle . . . . . . . . . . . . . . . . . 74
SPEX Long Life Coating. . . . . . . . . . . . . . 63
SPIKE Concrete Anchors . . . . . . . . 178-182
Spud Wrenches . . . . . . . . . . . . . . . . . . . 296
Stainless Capped SHead Screws . . . . . . . . 19
STAINLESS STEEL Fasteners
BLAZER 410 Self-drilling . . . . . . 11-12
FLAT-TOP 410 Self-drilling . . . . . . . 22
SD300 304 Self-drilling . . . . . . . . . . 11
Staplers. . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Staples . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Steel Framing Screws. . . . . . . . . . . . . . . . 87
Step Drill Bits . . . . . . . . . . . . . . . . . . . . . 289
Storage Boxes (Jobsite) . . . . . . . . . . . . . 374
STRAP-TOGGLE . . . . . . . . . . . . . . . . 97-98
STRESS-LESS Framing Fastener . . . . . . 87
STRESS-LOK Clamping Washer . . . . . 198
Strut and Channel Framing . . . . . . . 114-118
Stud-Tapping. . . . . . . . . . . . . . . . . . . . . . . 36
TamperProof Fasteners and Tools . . . . . . 44
Tapcon. . . . . . . . . . . . . . . . . . . . . . . 127-129
TAPCON Installation Kit . . . . . . . . . . . . . 127
Large Diameter . . . . . . . . . . . . . . . . . 130
Tapes -
Acrylic
Aluminum
Caution
Duct
Electrical
Facing
Foam
Foil
Masking
Polyester
Vinyl . . . . . . . . . . . . . . . . . . . . . . 359-364
Tapping Screws T. . . . . . . . . . . . . . . . . . 25-26
Hole Sizes . . . . . . . . . . . . . . . . . . . . . 387
Tarps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
Technical Data . . . . . . . . . . . . . . . . . . . . 381
ACQ Treated Lumber Information . . 397
Bolt Strength . . . . . . . . . . . . . . . 389-391
Corrosion . . . . . . . . . . . . . . . . . 393-395
Drive Systems . . . . . . . . . . . . . . . . . 383
Fastener Properties . . . . . . . . . . . . . 382
Galvanic Corrosion Chart . . . . . . . . 384
Head Styles . . . . . . . . . . . . . . . . . . . 383
Hole Sizes for Tapping Screws . . . . 387
Material Thickness Chart . . . . . . . . . 401
Nut Strengths . . . . . . . . . . . . . . . . . . 392
Plating. . . . . . . . . . . . . . . . . . . . 395-396
Point Types . . . . . . . . . . . . . . . . . . . 385
Self-Drilling Screw Data. . . . . . . . . . 388
Shoulder Types . . . . . . . . . . . . . . . . 384
Stainless Steel . . . . . . . . . . . . . 398-400
Thread Types. . . . . . . . . . . . . . 385, 386
Torsional Strength . . . . . . . . . . . . . . 387
Washer Types . . . . . . . . . . . . . . . . . 384
Termination Bar . . . . . . . . . . . . . . . . . . . . 64
Threaded Rod. . . . . . . . . . . . . . . . . . . . . 126
Tie Wire . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Tie Wire Insulation Tooling . . . . . . . . . 90-91
TILE-BOND Adhesive. T. . . . . . . . . . . . . . . 79
Toggle Bolts - Lightweight Decks . . . . . . . 72
Toggle Bolts . . . . . . . . . . . . . . . . . . . . 36, 59
Strap Toggle. . . . . . . . . . . . . . . . . . 97-98
Toggles . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
TRACER Drywall Fasteners . . . . . . . . 83-84
TRAKFAST - Gas Charged Tool . . . . . 85-86
TRUBOLT Wedge Anchors . . . . . . . 139-142
TUBE-LOK Fasteners. . . . . . . . . . . . . . . . 82
TWISTER Pre-Tied Wires . . . . . . . . . . . . 88
U-Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . 126
ULP - Ultra Low Profile Fastener . . . . . . . 15
Umbrella
U-V
Inserts and
Stubby Screens . . . . . . . . . . . . . 167-172
Parts . . . . . . . . . . . . . . . . . . . . . . . . . 176
Underlayment - GRACE . . . . . . . . . . . . . 349
Vacuum Cleaners . . . . . . . . . . . . . . . . . . 248
Vented
VICE GRIP Locking Pliers . . . . . . . . . . . 292
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 402
Washered Fasteners . . . . . . . . . . . . . . . . . 9
Washers . . . . . . . . . . . . . . . . . . . . . 193-194
Load Distributing . . . . . . . . . . . . . . . . 198
Waterproofing - PEAL & SEAL . . . . . . . 350
WD-40 Lubricant. . . . . . . . . . . . . . . . . . . 357
Wedge Anchor. W. . . . . . . . . . . . . . . . 139-142
WEDGE BOLT
Fasteners and Drill Bits . . . . . . . 130-177
Wood Boring Drill Bits. . . . . . . . . . . . . . . 290
Wood Deck Screws - Carbon
and Stainless. . . . . . . . . . . . . . . . . . . . 31
Wood Knocker Insert . . . . . . . . . . . . . . . 146
Wood Screws - Flat Countersunk. . . . . . . 36
Wood to Metal Fasteners (Blazer) . . . . . . 10
Wood to Metal Fasteners (Buildex) . . . . . 16
Wrenches - Spud / Adjustable / Ratchet Box /
Structural . . . . . . . . . . . . . . . . . . . . . . 296
Z
ZAMAC Zinc Nail-in Anchor . . . . . . 183-184
Zinc Head Fasteners (Buildex). . . . . . . . . 19
Zinc Head Fasteners (ZAC) . . . . . . . . . . . 21
FASTENERS
PAGES 7-198
TOOLS
PAGES 199-322
SEALANTS
PAGES 323-364
CONTRACTOR SUPPLIES
PAGES 365-380
TECHNICAL DATA
PAGES 381-401
(800) 486-1832 www.trianglefastener.com 4

WHO WE ARE..
SPECIALTY FASTENERS AND SERVICES
FOR COMMERCIAL CONSTRUCTION
Since 1977, Triangle Fastener Corporation
has supplied the construction industry with the
most comprehensive lines of standard
and specialty fastening systems solutions.
We are committed to offering the latest
fastening systems technologies that provide
high performance and low in-place costs.
But that’s only part of the story…
We offer local inventories and services that
meet your performance and quality demands.
Our “hands-on” approach to servicing your
needs guarantees that you get the attention
you deserve.
MARKETS SERVED
We serve the fastening systems needs of the following core markets.
• Flat Roofing: Low Slope Roofing Industry
• Metal Building: Metal Building, Metal Roofing and Siding
• Drywall: Commercial Steel Framing, Drywall, EIFS
• General Contracting: HVAC, Electrical, Mechanical
LOCATIONS
Stop by our showroom and be serviced by our knowledgeable staff of
fastening systems specialists. We offer a variety of products for
metal, wood, concrete, and drywall applications.
With over 15,000 standard and specialty items in stock, we can ship
most orders the same day! Our “Market Specific” programs
guarantees that we’ll have the fastener you need. Our local delivery
capabilities will get your order to the job site when you need it!
SERVICES
• Computerized Inventory Management
• Direct Sales Team
• Job Site Assistance
• Engineering Support
• Product Development
• Delivery program
• Inventory management programs
LOCATIONS
WITH PAINTING
CAPABILITIES
How can we help you?
CONTACT US FOR YOUR NEXT
CONSTRUCTION FASTENING
REQUIREMENT!
5
TRIANGLE FASTENER CORPORATION

CONSTRUCT BETTER, FASTER, & LESS COSTLY
From the time we pick up the phone, to long after the product is used, we
are here to help you! We provide the most innovative products, superior
service, and a focused approach to your specific requirements. Our
commitment to developing quality products and programs assure easy
installation at low cost.
“TFC SPECIFIC” PRODUCTS AND PROGRAMS
These products are designed by and offered exclusively from TFC.
They provide higher performance than products that are typically used.
• BLAZER High Performance Drill Screws
• TRACER High Performance Drywall Screws
• SENTRY PLUS FIVE High Performance Roofing Screws
• PANEL-TITE Metal to Wood Fasteners
• CONCEALOR Low Profile Head Fasteners
• ULP Ultra Low Profile Fasteners
• MP14 Multi-purpose Fasteners
• PIPE-MASTER Metal Roofing Pipe Flashing
• PAK-ONE Job Pack Program
• STRESS-LESS Stress Reducing Fastener
• GET-A-GRIP In-Stock Painted Rivets
• KALIDA-KOTE Paint For Fasteners, Rivets, Closures
• SD300 304 Stainless Steel Drill Screws
• TWISTER Pre-tied Wires
• BRACER Bracing System Washers
• BLAZER ULTRA Framing Fasteners
WITH EVERY PRODUCT WE SUPPLY,
YOU’LL GET THE MOST COMPREHENSIVE SUPPORT PROGRAMS.
DISTRIBUTION
23 locations are stocked full
of standard and specialty
fastening system solutions.
Computerized inventory
control allows immediate
access from every location.
PRODUCT DESIGN
Our TFC Fastening
System Design Center
can custom design
products to meet your
application requirements.
MARKET SPECIFIC SPECIALISTS
Each of our locations are
supported by our direct sales
staff geared to handle the
market’s specific product and
service requirements.
JOB SITE SUPPORT
We provide job-site assistance
for everything we sell. Our
trained service team provides
the latest fastening system
technologies.
PRODUCT RESEARCH
The products we offer meet
or exceed industry standards.
We can also provide
additional research to fit your
specific needs.
TOOL REPAIR
We don’t just sell tools,
we fix them too! Just bring
them to the branch and
we will have them
serviced in no time flat!
(800) 486-1832 www.trianglefastener.com 6

FASTENERS
We offer a wide variety of fasteners for fastening into various substrates. They include standard and specialty products
for metal, wood, concrete, drywall, and plastic substrates. These fasteners provide high performance and are designed
for professional construction applications. They are backed by the manufacturer’s warranty assuring high quality.
ACCUDRIVE - ACCUTRAC
ROOFING TOOLS . . . . . . . . . . . . . . . . . . . . . . . 57
ACOUSTICAL
A
CEILING CLIPS . . . . . . . . . . . . . . 88, 110-111
ACOUSTICAL TIE WIRES . . . . . . . . . . . . . . 88
INSTALLATION TOOLS . . . . . . . . . . . . . . . . . 91
ANCHOR BOLTS . . . . . . . . . . . . . . . . . . . . . 126
ATLAS FASTENERS - FLATTOP . . . . . . . . . . . . 22
AUTOTRAXX / UNIDEK /
FASTRAXX METAL DECK TOOL . . . . . . . . . . 59
BASE PLY FASTENERS
FASTENING PATTERNS . . . . . . . . . . . . . . . . 71
FM90, FM75 , TWINLOK ,
LOC-NAIL, NAIL-TITE, DO-ALL . . . . 65-71
BATTEN STRIP . . . . . . . . . . . . . . . . . . . . . . . 56
BEAM CLAMPS. . . . . . . . . . . . . . . . . . . 119-120
BLAZER SELF-DRILLING FASTENERS . . . . . 9 - 12
B-LINE FASTENERS . . . . . . . . . . . . . . . 121-125
BOLTS. . . . . . . . . . . . . . . . . . . . . . . . . 189-190
BRACING SYSTEM COMPONENTS
BRACER HILLSIDE WASHER. . . . . . 197-198
CABLE GRIPS - DEAD ENDS, BRACE GRIP . . 198
EYEBOLTS . . . . . . . . . . . . . . . . . . . . . . . 198
BUILDEX ROOFING SCREWS -
ROOFGRIP / HEXTRA. . . . . . . . . . . . . 53-54
BUILDEX SELF-DRILLING FASTENERS . . . . . 16-20
BUTTON CAP NAILS . . . . . . . . . . . . . . . . . . . 45
CABINET SCREWS . . . . . . . . . . . . . . . . . . 33-35
CABLE TIES . . . . . . . . . . . . . . . . . . . . . . . . 196
CAP NAILS - SIMPLEX. . . . . . . . . . . . . . 81-82
CAP SCREWS . . . . . . . . . . . . . . . . . . . . . . . 190
CAPS FOR SCREW HEADS - PLASTIC . . . . . . . 30
CAPS FOR SCREW TIPS - RUBBER . . . . . . . . 195
CARRIAGE BOLTS . . . . . . . . . . . . . . . . . . . . 190
CEILING CLIPS - POWDER ACTUATED . . . 110-111
CEILING CLIPS - TIE WIRE. . . . . . . . . . . . . . . 88
CEMENT BOARD SCREWS . . . . . . . . . . . . . . . 84
CEMENT BOARD SCREWS - ROCK-ON . . . . 104
CLIMASEAL LONG LIFE COATING . . . . . . . . 63
COLORFIXX / COLORHEXX
NYLON HEAD FASTENERS . . . . . . . . . . . . . . . 30
CONCEALOR PANCAKE HEAD FASTENERS . 13-14
CONCRETE ANCHORS
BLOCK PLUG . . . . . . . . . . . . . . . . . . . 177
CAPSULES. . . . . . . . . . . . . . . . . . . . 174-175
DYNABOLT SLEEVE ANCHORS . . . . 135-138
EPCON A7 ACRYLIC ADHESIVE. . . . 147-154
EPCON C6 FAST CURING EPOXY . . . 155-160
EPCON G5 EXTENDED
WORKING TIME EPOXY . . . . . . . . . . . . 161-166
FIBERPLUG . . . . . . . . . . . . . . . . . . . . 186
HOLE ACCESSORIES -
HOLE PLUGS / BRUSHES / TUBING . . . . . 176
LEAD ANCHORS . . . . . . . . . . . . . . . . . . . 186
LEAD, PLASTIC, FIBERPLUG. . . . . . . . . . 94
MULTI-SETT II
DROP-IN ANCHORS . . . . . . . . . . . . . 143-146
NAIL IN DRIVE PIN ANCHORS. . . . . . . . . . 185
B C C
PLASTIC LIGHTWEIGHT ANCHOR
AND FLUTED ANCHOR . . . . . . . . . . . . . . . 187
REDI-BOLT SLEEVE ANCHORS . . . . 133-134
SPIKE . . . . . . . . . . . . . . . . . . . . . 178-182
TAPCON INSTALLATION KIT . . . . . . . . . . 130
TAPCON THREADED . . . . . . . . . . . 127-129
TRUBOLT WEDGE ANCHORS . . . . . 139-142
7
TRIANGLE FASTENER CORPORATION

FASTENER INDEX
UMBRELLA INSERTS AND
STUBBY SCREENS . . . . . . . . . . . . . . 167-173
WEDGE BOLT FASTENERS
AND DRILL BITS . . . . . . . . . . . . . . . . . . . 177
ZAMAC NAIL IN ANCHORS . . . . . . . 183-184
CONCRETE FASTENING SYSTEMS -
OVERVIEW OF PRODUCTS. . . . . . . . . . . 131-132
CORROSION RESISTANT SCREWS . . . . . . . . . . 11
COUPLING NUTS . . . . . . . . . . . . . . . . . . . . . 192
DEC-KING EXTERIOR WOOD SCREWS . . . . . 32
DEC-U-DRIVE STAND-UP TOOL. . . . . . . . . . 32
D
DIAPHRAGM SCREW - POST FRAME . . . . . . . . 28
DRYWALL ANCHORS -
EZ PRODUCTS . . . . . . . . . . . . . . . . . . . . . 93
PLASTIC EXPANSION . . . . . . . . . . . . . . . . . 96
PLASTIC LIGHT DUTY ANCHORS . . . . . . . . . 94
POLLY / EXPANSION. . . . . . . . . . . . . . . . . 95
TOGGLES. . . . . . . . . . . . . . . . . . . . . . . . . 95
DRYWALL FASTENERS . . . . . . . . . . . . . . . 83-84
EIFS FASTENING SYSTEMS . . . . . . . . . . 99-103
ES PRODUCTS . . . . . . . . . . . . . . . . . . . . 65-71
EXPLOSION VENTING FASTENERS . . . . . . . . . . 42
EXTENSION POLES -
E-G
POWDER ACTUATED TOOLS . . . . . . . . . . . . . . 89
EYEBOLTS . . . . . . . . . . . . . . . . . . . . . . . . . 198
E-Z PRODUCTS - DRYWALL HANGERS . . . . . . 93
FABLOK RIVETS . . . . . . . . . . . . . . . . . . . . . 41
FROTH-PAK SPRAY INSULATION . . . . . . . . . 77
FURNITURE SCREWS . . . . . . . . . . . . . . . . . . . 33
GEARLOK ROOFING PLATES . . . . . . . . . . . . 55
GRID MASTER . . . . . . . . . . . . . . . . . . . . . 99
GRID MATE PLATES AND FASTENERS . 101-104
GROMMET SEAL RIVETS . . . . . . . . . . . . . . . . 42
HANGER STUDS . . . . . . . . . . . . . . . . . . . . . . 36
HEAT WELDING TOOL . . . . . . . . . . . . . . . . . . 74
HEAVY GAUGE DRILL SCREWS . . . . . . . 10 & 16
ICH
H-J
TRAXX SELF-DRILLING FASTENERS . . . . 62
INSTA-STICK ROOFING ADHESIVE . . . . . . . . 75
INSULATED PANEL FASTENERS (IPF) . . . . . . . 25
INSULATION (RIGID) FASTENERS . . . . . . . . . . . 17
INSULATION (RIGID) PLATES . . . . . . . . . . . . . . 50
INSULATION BOARD
INSTALLATION TOOLS (EFIS) . . . . . . . . . . . . . 99
J-CLIP AND J-MASTER TOOLS . . . . . . . . . . 90
LADD OVERHEAD FASTENING SYSTEM . . . . 106
L
LAG SCREWS . . . . . . . . . . . . . . . . . . . . . . . 191
LAG SHIELD INSERT . . . . . . . . . . . . . . . . . . . 36
LAGMASTER INSTALLATION TOOL . . . . . . . 91
LEAD CONCRETE ANCHORS . . . . . . . . . . . . . . 94
LEISTER HEAT WELDING SEAMING TOOL . . . 74
LELAND FASTENERS . . . . . . . . . . . . . . . . . . . 28
LIGHTWEIGHT DECK FASTENERS -
TOGGLE BOLTS / NTB / NC FASTENERS. 72 - 73
LOADS - POWDER ACTUATED . . . . . . . . . . . . 112
LOW PROFILE HEAD FASTENERS. . . . . . . . 13-14
M
N
ONE-STEPPER PLASTIC PANEL FASTENERS . . 29
PAN AMERICAN FASTENERS . . . . . . . . . . . . . . 33
PANEL-TITE POST FRAME FASTENERS . . . . . . 27
PASLODE
O-Q
- NAIL TOOL . . . . . . . . . . . . . . . 47-48
PINS - POWDER ACTUATED . . . . . . . . . . 108-111
PINS AND FUEL - TRAKFAST. . . . . . . . . . . . 86
POP TOGGLE DRYWALL ANCHORS . . . . . . . 96
POST FRAME SCREWS (PANEL-TITE) . . . . . . . 27
MACHINE SCREWS . . . . . . . . . . . . . . . . . . . 188
METAL DECKING FASTENING TOOLS . . . . . . . . 59
METAL TO WOOD FASTENERS (PANEL-TITE) . . 27
MOUNTING BRACKETS - CONDUIT / BOX /
ROD AND WIRE / STRAP . . . . . . . . . . . 121-125
NAILERS - PASLODE / SENCO . . . . . . . 47-49
NAILS - . . . . . . . . . . . . . . . . . . . . . . . . . 45-46
NC FASTENERS . . . . . . . . . . . . . . . . . . . . . . 73
NTB FASTENERS . . . . . . . . . . . . . . . . . . . . . 72
NUTS . . . . . . . . . . . . . . . . . . . . . . . . . 191-192
NYLON HEAD FASTENERS . . . . . . . . . . . . . . . 30
POWDER ACTUATED -
PINS / LOADS / CEILING CLIPS . . . . . . . 108-114
POWDER ACTUATED PINS
AND LOADS (DECKING) . . . . . . . . . . . . . . . . . . 61
POWDER ACTUATED TOOLS . . . . . . . . . 105-107
PRE-TIED WIRES - TWISTER. . . . . . . . . . . . 88
PULLOUT TESTING. . . . . . . . . . . . . . . . . . . . . 80
QUIK DRIVE FASTENERS AND TOOLS . . . . . . . 37
REZTITE STEEL FRAME FASTENERS. . . . . . . 23
RIVET INSTALLATION TOOLS . . . . . . . . . . . . . . 40
RIVETS - BLIND. . . . R. . . . . . . . . . . . . . . . . . . 39
RIVETS - FABLOK . . . . . . . . . . . . . . . . . . . . 41
RIVETS - GROMMET SEAL . . . . . . . . . . . . . . . 42
RIVETS - PAINTED . . . . . . . . . . . . . . . . . . . . . 39
ROCK-ON CEMENT BOARD FASTENERS . . . 104
ROOF SCREW PLATES. . . . . . . . . . . . . . . . . . 50
ROOFING SCREWS - TECHNICAL DATA . . . . . . 52
ROOFING SCREWS (BUR) . . . . . . . . . . . . 50-63
SAMMY SUPER SCREWS . . . . . . . . . . . . 92
SCOTS STAINLESS CAP HEAD FASTENERS . . 19
SCREW TIP CAPS . . . . . . . . . . . . . . . . . . . . 195
S
SCRUBOLT . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SEAMING TOOL - HEAT WELDING . . . . . . . . . . 74
SELF-DRILLING FASTENERS -
CARBON. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DRYWALL . . . . . . . . . . . . . . . . . . . . . . . . . 84
FRAMING . . . . . . . . . . . . . . . . . . . . . . . . . 87
LARGE DIAMETER . . . . . . . . . . . . . . . . . . . 23
TORX DRIVE. . . . . . . . . . . . . . . . . . . . . . . 87
STAINLESS STEEL . . . . . . . . . . . . . . . . . . . 11
SELF-SEALING FASTENERS. . . . . . . . . . . . . . . . 9
SELF-SEALING FASTENERS (MAXISEAL) . . . . . . 18
SELF-TAPPING FASTENERS
CARBON AND STAINLESS . . . . . . . . . . . . . . 26
DRYWALL . . . . . . . . . . . . . . . . . . . . . . . . . 83
SENTRY PLUS FIVE ROOFING SCREWS . . . 50-52
SHEET METAL SCREWS - HWH / PAN HEAD. . 36
SHEETING SCREWS. . . . . . . . . . . . . . . . . . . . 26
SIMPLEX ROOFING CAP NAILS . . . . . . . . . . 81
SPEED-LOK TOGGLE . . . . . . . . . . . . . . . . . 74
SPEX LONG LIFE COATING . . . . . . . . . . . . . 63
SPIKE CONCRETE ANCHORS. . . . . . . . 178-182
SPIKE CONCRETE ANCHORS (BUR) . . . . . . 74
STAINLESS STEEL FASTENERS
S
CAP HEAD FASTENERS (SCOTS) . . . . . . . 19
BLAZER . . . . . . . . . . . . . . . . . . . . . . 11-12
FLAT-TOP . . . . . . . . . . . . . . . . . . . . . . . 22
MARUTEX . . . . . . . . . . . . . . . . . . . . . . . . . 21
STAPLERS AND STAPLES . . . . . . . . . . . . . . . . 49
STEEL FRAME FASTENERS
BLAZER ULTRA . . . . . . . . . . . . . . . . . . 87
FABCO REZTITE . . . . . . . . . . . . . . . . . . . 23
STRAP-TOGGLE. . . . . . . . . . . . . . . . . . . . 97
STRESSLESS FRAMING FASTENER . . . . . . . . . 24
STRUT AND CHANNEL FRAMING . . . . . . 115-118
TAMPERPROOF FASTENERS AND TOOLS. . . 43-44
TAPCON . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
TAPCON INSTALLATION TKIT . . . . . . . . . . . . . . 130
TERMINATION BAR. . . . . . . . . . . . . . . . . . . . . 64
THREADED ROD HANGERS . . . . . . . . . . . . . 126
TILE-BOND ADHESIVE . . . . . . . . . . . . . . . . 79
TOGGLE BOLTS . . . . . . . . . . . . . . . . . . . . . . 36
TOGGLE BOLTS - LIGHTWEIGHT DECKS. . . . . . 72
TRACER DRYWALL FASTENERS . . . . . . . . . . 83
TRAKFAST - GAS CHARGED TOOL . . . . . . . 85
TUBE-LOK FASTENERS . . . . . . . . . . . . . . . . 82
TWISTER PRE-TIED WIRES . . . . . . . . . . . . . 88
U-BOLTS . . . . . . . . . . . . . . . . . . . . . . . . . . 126
ULP - ULTRA LOW PROFILE FASTENER . . . . . 15
WASHERED FASTENERS. . . . . . . . . . . . . . . . . . 9
WASHERS . . . . . . . . . . . . . . . . . . . . . . 193-194
WOOD DECK SCREWS -
CARBON AND STAINLESS . . . . . . . . . . . . . . . . 31
WOOD SCREWS - FLAT COUNTERSUNK. . . . . . 36
U-Z
WOOD TO METAL FASTENERS (BLAZER) . . . . . 10
WOOD TO METAL FASTENERS (BUILDEX) . . . . 16
ZAMAC ZINC NAIL IN ANCHOR . . . . . . 183-184
ZINC HEAD FASTENERS (BUILDEX) . . . . . . . . . 19
ZINC HEAD FASTENERS (ZAC) . . . . . . . . . . . 23
(800) 486-1832 www.trianglefastener.com 8

BLAZER HIGH PERFORMANCE DRILL SCREWS
CARBON STEEL - .00015” MIN ELECTRO ZINC PLATED
Point Head Drilling
Size Type Style Thickness
HEX WASHER HEADS
Light & Medium Gauge Applications
• Sharp non-walking point for fast
penetration into high tensile steel.
• Variety of head styles and lengths to
meet any application need.
• BLAZERS are produced to
SAE J-78 standards.
For steel framing applications see page 87
ALL BLAZERS ARE SHIPPED
IN EASY TO HANDLE
PLASTIC CONTAINERS!
#6-20 x 3/8” DP2 1/4” HWH .036” - .100”
#6-20 x 1/2” DP2 1/4” HWH .036” - .100”
#6-20 x 3/4” DP2 1/4” HWH .036” - .100”
#6-20 x 1” DP2 1/4” HWH .036” - .100”
#8-18 x 1/2” DP2 1/4” HWH .036” - .100”
#8-18 x 5/8” DP2 1/4” HWH .036” - .100”
#8-18 x 3/4” DP2 1/4” HWH .036” - .100”
#8-18 x 1” DP2 1/4” HWH .036” - .100”
#8-18 x 1-1/4”` DP2 1/4” HWH .036” - .100”
#8-18 x 1-1/2” DP2 1/4” HWH .036” - .100”
#8-18 x 2” DP2 1/4” HWH .036” - .100”
#10-16 x 1/2” DP3 5/16” HWH .036” - .175”
#10-16 x 5/8” DP3 5/16” HWH .036” - .175”
#10-16 x 3/4” DP3 5/16” HWH .036” - .175”
#10-16 x 1” DP3 5/16” HWH .036” - .175”
#10-16 x 1-1/4” DP3 5/16” HWH .036” - .175”
#10-16 x 1-1/2” DP3 5/16” HWH .036” - .175”
#10-16 x 2” DP3 5/16” HWH .036” - .175”
#10-16 x 3” DP3 5/16” HWH .036” - .175”
#12-14 x 1” DP3 5/16” HWH .036” - .210”
#12-14 x 1-1/4” DP3 5/16” HWH .036” - .210”
#12-14 x 1-1/2” DP3 5/16” HWH .036” - .210”
#12-14 x 2” DP3 5/16” HWH .036” - .210”
#12-14 x 2-1/2” DP3 5/16” HWH .036” - .210”
#12-14 x 3” DP3 5/16” HWH .036” - .210”
1/4-14 x 3/4” DP3 3/8” HWH .036” - .250”
1/4-14 x 1” DP3 3/8” HWH .036” - .250”
1/4-14 x 1-1/4” DP3 3/8” HWH .036” - .250”
1/4-14 x 1-1/2” DP3 3/8” HWH .036” - .250”
1/4-14 x 2” DP3 3/8” HWH .036” - .250”
1/4-14 x 2-1/2” DP3 3/8” HWH .036” - .250”
1/4-14 x 3” DP3 3/8” HWH .036” - .250”
1/4-14 x 4” DP3 3/8” HWH .036” - .250”
1/4-14 x 5” DP3 3/8” HWH .036” - .250”
1/4-14 x 6” DP3 3/8” HWH .036” - .250”
HEX WASHER HEAD
WITH BONDED WASHERS
Galvanized Washer vulcanized to EPDM
• Sharp non-walking point for fast
penetration into high tensile steel.
• Bonded EPDM washers withstands
harsh weather conditions.
• TRI-SEAL long-life coated for superior
corrosion protection.
Available in “Flange
Undercut” Style
12MM O.D. WASHER
16MM O.D. BONDED SEALING WASHER
CARBON STEEL - .0003” MIN. ZINC PLATED
Point Head Drilling
Size Type Style Thickness
#8-18 x 3/4” DP2 1/4” HWH .036” - .100”
#8-18 x 1” DP2 1/4” HWH .036” - .100”
#8-18 x 1-1/4”` DP2 1/4” HWH .036” - .100”
#8-18 x 1-1/2” DP2 1/4” HWH .036” - .100”
#10-16 x 3/4” DP3 5/16” HWH .036” - .175”
#10-16 x 1” DP3 5/16” HWH .036” - .175”
#10-16 x 1-1/4” DP3 5/16” HWH .036” - .175”
#10-16 x 1-1/2” DP3 5/16” HWH .036” - .175”
#12-14 x 3/4” DP3 5/16” HWH, FU .036” - .210”
#12-14 x 1” * DP3 5/16” HWH, FU .036” - .210”
#12-14 x 1-1/4” * DP3 5/16” HWH, FU .036” - .210”
#12-14 x 1-1/2” * DP3 5/16” HWH .036” - .210”
#12-14 x 2” * DP3 5/16” HWH .036” - .210”
#12-14 x 2-1/2” DP3 5/16” HWH .036” - .210”
#12-14 x 3” DP3 5/16” HWH .036” - .210”
1/4-14 x 3/4” DP3 3/8” HWH .036” - .250”
1/4-14 x 7/8” * DP1/Lap 5/16” HWH, FU .036” - .090”
1/4-14 x 1”* DP3 3/8” HWH .036” - .250”
1/4-14 x 1-1/4” * DP3 3/8” HWH .036” - .250”
1/4-14 x 1-1/2” * DP3 3/8” HWH .036” - .250”
1/4-14 x 2” DP3 3/8” HWH .036” - .250”
1/4-14 x 2-1/2” DP3 3/8” HWH .036” - .250”
1/4-14 x 3” DP3 3/8” HWH .036” - .250”
1/4-14 x 4” DP3 3/8” HWH .036” - .250”
1/4-14 x 5” DP3 3/8” HWH .036” - .250”
1/4-14 x 6” DP3 3/8” HWH .036” - .250”
* Supplied with long-life coating / 1,000 hours salt spray
FU = Flange Undercut
9
TRIANGLE FASTENER CORPORATION

BLAZER SELF-DRILLING FASTENERS
®
HEAVY GAUGE FASTENERS
• Drill and tap up to 1/2” thick steel!
• Long-life coated!
• Lengths up to 8”
• Available with and without
EPDM bonded washers
CARBON STEEL WITH LONG LIFE COATING -
1,000 HRS SALT SPRAY
Max.
Point Head Drilling Material Box
Size Type Style Thickness Thickness Qty.
#12-24 x 7/8” DP4 5/16” HWH .125” -.375” .325” 4M
#12-24 x 1-1/4” DP5 5/16” HWH .250” -.500” .375” 4M
#12-24 x 1-1/2” DP5 5/16” HWH .250” -.500” .625” 2M
#12-24 x 2” DP5 5/16” HWH .250” -.500” 1.125” 2M
1/4-20 x 3” DP5 3/8” HWH .250” - .500” 2.000” 500
1/4-20 x 4” DP5 3/8” HWH .250” - .500” 3.100” 500
1/4-20 x 5” DP5 3/8” HWH .250” - .500” 4.200” 250
1/4-20 x 6” DP5 3/8” HWH .250” - .500” 5.200” 250
1/4-20 x 7” DP5 3/8” HWH .250” - .500” 6.200” 250
1/4-20 x 8” DP5 3/8” HWH .250” - .500” 7.200” 250
PHILLIPS PAN HEADS
Light & Medium Gauge Applications
• Great for HVAC and steel stud applications.
• Deep phillips recess assures driving stability.
CARBON STEEL - .00015” MIN. ELECTRO ZINC PLATED
Max.
Point Head Drilling Material Box
Size Type Style Thickness Thickness Qty.
#6-20 x 3/8” DP2 #2 Phil Pan .036” - .100” .100” 15M
#6-20 x 1/2” DP2 #2 Phil Pan .036” - .100” .205” 15M
#6-20 x 3/4” DP2 #2 Phil Pan .036” - .100” .455” 10M
#6-20 x 1” DP2 #2 Phil Pan .036” - .100” .705” 10M
#8-18 x 1/2” DP2 #2 Phil Pan .036” - .100” .205” 10M
#8-18 x 3/4” DP2 #2 Phil Pan .036” - .100” .455” 10M
#8-18 x 1” DP2 #2 Phil Pan .036” - .100” .705” 7.5M
#8-18 x 1-1/4”` DP2 #2 Phil Pan .036” - .100” 1.000” 5M
#8-18 x 1-1/2” DP2 #2 Phil Pan .036” - .100” 1.205” 5M
#8-18 x 2” DP2 #2 Phil Pan .036” - .100” 1.750” 1.5M
#10-16 x 1/2” DP3 #2 Phil Pan .036” - .175” .150” 10M
#10-16 x 5/8” DP3 #2 Phil Pan .036” - .175” .200” 10M
#10-16 x 3/4” DP3 #2 Phil Pan .036” - .175” .325” 7.5M
#10-16 x 1” DP3 #2 Phil Pan .036” - .175” .575” 5M
#10-16 x 1-1/4” DP3 #2 Phil Pan .036” - .175” .825” 3.5M
#10-16 x 1-1/2” DP3 #2 Phil Pan .036” - .175” 1.075” 3M
FLAT COUNTERSUNK
HEADS
FLAT WAFER
HEADS
WOOD TO METAL
• Drill and tap up to 1/4” thick steel!
• Special wings keeps wood from splitting
and helps countersink the head.
Try our HEADER LG for light gauge
applications!
• Wafer head seats flush in wood.
* Note: TRI-ACQ TM coating applied on the
fastener. Acceptable for use in ACQ
treated lumber.
* No wings
WITH WINGS - CARBON STEEL - .00015” MIN. ZINC PLATED
Max.
Point Head Drilling Material Box
Size Type Style Thickness Thickness Qty.
#10-24 x 1-7/16” DP3 Phil Flat Wafer .075” - .250” .250” -.750” 4M
#12-14 x 1-3/4”* DP2 Sq Flat Cntrscnk .048” - .210” .250” - .750” 5M
#12-24 x 2” DP4 Phil Flat Cntrsnk .125” - .375” .750” - 1.375” 1.5M
#12-24 x 2-1/4” DP4 Phil Flat Cntrsnk .125” - .375” .750” - 1.375” 1.5M
#12-14 x 2-1/2”* DP2 Sq Flat Cntrscnk .048” - .210” .500” - 1.625” 1M
1/4-20 x 2-3/4”* DP4 Phil Flat Cntrsnk .125” - .375” .750” - 1.625” 1M
1/4-20 x 3-1/4”* DP4 Phil Flat Cntrsnk .125” - .375” .750” - 2.500” 900
1/4-20 x 3-3/4”* DP4 Phil Flat Cntrsnk .125” - .375” .750” - 3.000” 500
PHILLIPS DRIVE - CARBON STEEL - ZINC PLATED
Max.
Point Head Drilling Material Box
Size Type Style Thickness Thickness Qty.
#10-24 x 3/4”* DP3 Phil Flat Wafer .036” - .175” .250” - .375“ 5M
#10-24 x 1” DP3 Phil Flat Wafer .075” - .250” .250” - .500” 5M
#10-24 x 1-1/4” DP3 Phil Flat Wafer .075” - .250” .250 - .750” 3.5M
#10-24 x 1-1/2” DP3 Phil Flat Wafer .075” - .250” .250” - 1.000” 3M
(800) 486-1832 www.trianglefastener.com 10

STAINLESS STEEL SELF-DRILLING SCREWS
Corrosion resistant fasteners for construction
410 STAINLESS STEEL
SELF-DRILLING FASTENERS
With or without bonded sealing washers
Provides good corrosion resistance to mild atmospheres. It resists
corrosion in many light industrial and domestic environments as well as
potable and mine waters.
For technical data, please refer to page 12.
Max
Description Thickness Carton
Range
Quantity
1/4” Diameter - Lap Point - 3/8” HWH
.090 Max drilling thickness
1/4 - 14 x 7/8” .325” 2.5M
#14-10 x 1” .450” 2.5M
1/4-14 x 1-1/8” (LP) .500” 2.5M
#8 Diameter - DP2 - 1/4” HWH
.100” Max drilling thickness
#8-18 x 1/2” .205” 10m
#8-18 x 3/4” .455” 10M
#8-18 x 1” .705” 7.5M
#10 Diameter - DP3 - 5/16” HWH
.175” Max drilling thickness
#10-16 x 1/2” .150” 10M
#10-16 x 3/4” .325” 7.5M
#10-16 x 1” .575” 5M
#10-16 x 1 1/2” 1.075” 3M
#12 Diameter - DP3 - 5/16” HWH
.210” Max drilling thickness
#12-14 x 3/4” .290” 5M
#12-14 x 1” .525” 3.5M
#12-14 x 1 1/4” (LP) .750” 3.5M
#12-14 x 1 1/2” 1.000” 2.5M
#12-14 x 2” 1.500” 2M
#12-14 x 2 1/2” 2.000” 1M
#1/4” Diameter - DP3 - 3/8” HWH
.250” Max drilling thickness
1/4 - 14 x 3/4” .210” 2.5M
1/4 - 14 x 1” .460” 2.5M
1/4 - 14 x 1 1/2” .960” 2M
1/4 - 14 x 2” 1.460” 1.5M
1/4 - 14 x 2 1/2” 2.460” 1M
1/4 - 14 x 3” 2.460” 500
PULLOUT STRENGTH
304 STAINLESS
SELF-DRILLING
Triangle Fastener offers a full line of fasteners
manufactured from 304 stainless steel. The
fastener head and threads are produced from
corrosion resistant stainless steel producing
exceptional corrosion protection and superior
ductility. A carbon steel drill point is hardened
and welded to the body allowing the fastener to
drill and tap in steel up to 1/2” thick!
Nominal Steel Thickness
24 GA 22 GA 20 GA 18 GA 16 GA 14 GA 12 GA 3/16”
Dia. & Point (.024”) (.030”) (.036”) (.048”) (.060”) (.075”) (.105”) (.187”)
#10-16 DP3 208 267 295 503 710 968 1,476*
#12-14 DP1/lap 261 338 390 649 908 1,259 1,949
#12 DP2 243 283 375 605 848 1,181
#12-14 DP3 215 292 343 555 752 1,066 1,634 2,990*
#12-14 DP5 468 697 986 1,535 2,822*
1/4-14 DP1/Lap 329 428 562 800 1,151
1/4-14 DP3 236 295 355 607 886 1,149 1,850 4,552*
* Ultimate pullout is restricted by tensile strength of the fastener
AVAILABLE IN THE FOLLOWING SIZES
Description Drilling Thickness
#10-16 x 3/4” DP3 HWH .036” -.175”
#12-14 x 1” DP3 HWH .036” - .210”
#12-14 x 1” DP3 T25 Pancake Hd .036” - .210”
#12-14 x 1” DP3 T25 Button Hd .036” - .210”
#12-14 x 1-1/8” DP1 HWH .036” - .210”
#12-14 x 1-3/8” DP2 HWH .036” - .210”
#12-14 x 1-1/2” DP5 HWH .125” - .500”
#12-14 x 2” DP3 HWH .036” - .210”
1/4-14 x 1” DP1/Lap .036” - .175”
1/4-14 x 1” DP3 .036” - .250”
With and Without Bonded Sealing Washers
HEAD SIZE:
MATERIAL:
FINISH:
SPECIFICATIONS
5/16” Hex Washer Head, T25 Pancake, T25
button head.
Head and Thread - 304 Stainless Steel
Drill Point - Carbon Steel Case Hardened
Electro Zinc Plated
FASTENER STRENGTH
#10-16 #12-14 1/4-14
TENSILE: 1,810 2,810 3,186
SHEAR: 1,147 2,046 2,880
Minimum Ultimate in Pounds
11
TRIANGLE FASTENER CORPORATION

BLAZER ®
SELF-DRILLING FASTENERS
Diameter
FASTENER TERMINOLOGY
Threads
Per Inch Length Point Type Head Style
#12 - 14 x 1-1/4” DP3 5/16” HWH
Head Style
Description
Threads
Per Inch
Length
Point
Type
INSTALLATION RECOMMENDATIONS
Screwgun RPM
#6, #8, 10, #12. . . . . . . . 0 - 2,500 RPM
1/4” & Heavy Gauge . . . 0 - 2,000 RPM
18-8 Stainless Steel . . . . 0 - 1,000 RPM
Diameter
Fasteners should be installed perpendicular to the fastening
surface. Torque control screwgun should be used to prevent
over torquing.
Decimal & Metric
Conversions
Gauge
Thknss
29 ga
28 ga
26 ga
24 ga
22 ga
20 ga
18 ga
16 ga
14 ga
12 ga
1/8”
10 ga
1/4”
5/16”
3/8”
1/2”
Decimal
Equivalent
.013”
.015”
.018”
.024”
.030”
.036”
.048”
.060”
.075”
.105”
.125”
.135”
.250”
.312”
.375”
.500”
Determining Drill Point
Type & Fastener Length
Add up total thickness that will be drilled
(include any voids and insulation). Refer
to drilling & material thickness on size
charts. Drilling should be completed
before tapping occurs
Metric
.33mm
.38mm
.46mm
.61mm
.76mm
.91mm
1.22mm
1.52mm
1.91mm
2.67mm
3.18mm
3.43mm
6.35mm
7.92mm
9.53mm
12.7mm
STRENGTHS OF FASTENERS
Fastener
Diameter
Torsional
(Inch Lbs.)
#6-20 (.125”) 25 1125 750
#8-18 (.164”) 42 1575 1000
#10-16 (.190”) 61 2100 1400
#12-14 (.216”) 92 2778 2000
#12-24 (.210”) 100 3188 2100
1/4-14 (.250”) 150 4275 2600
1/4-20 (.250”) 56 4275 2700
TECHNICAL DATA
Tensile
(Pounds)
Metric Conversion Formulas
Pullout Values In Steel - Average Ultimate Pounds
Carbon Steel and 410 Stainless Fasteners
Steel #6-20 #8-18 #10-16 #12-14 #12-24 1/4-14 1/4-14 1/4-20 1/4-20
Thknss DP2 DP2 DP3 DP3 DP5 DP1/Lap DP3 DP4 DP5
26 ga 120 119 126 143 211 142
24 ga 183 193 208 215 332 236
22 ga 248 265 267 292 431 295
20 ga 296 298 295 343 565 355
18 ga 471 491 503 555 468 803 607 554
16 ga 679 703 710 752 697 1154 886 708
14 ga 847 959 968 1066 986 1149 1116
12 ga 1476 1634 1535 1850 1803
3/16” 2990 3715 4552 4297 2672
1/4” 3844 5032 3629
3/8” 3791
1/2” 4739
Shear
(Pounds)
Need a custom
designed fastener or
application tests?
Call our Fastening Systems
Design Center at
(216) 351-9933
Convert English to Metric
Formula to Use
Decimal to Millimeters
Decimal x 25.4 = Millimeter
PSI to Newton/Millimeters 2 PSI x .007 = Newton/millimeter 2 (N/mm 2 )
Pounds Force to Newtons
Pounds Force x 4.448 = Newtons
MATERIAL PROPERTIES
Material . . . . . . . . . . . . . C1018 - C1022
Heat Treatment . . . . . . . Case Hardened
Case Hardness . . . . . . . Rockwell C 52-58
Case Depth
#6 dia. : . . . . . . . . . . . . . .002”/.007”
#8 thru #12: . . . . . . . . . . .004”/.009”
1/4”: . . . . . . . . . . . . . . . . .005”/.011”
Core Hardness. . . . . . . . Rockwell C 32-40
Ductility . . . . . . . . . . . . . 5 degrees min.
Shear Values In Steel
(Average Ultimate Pounds)
MATERIAL PROPERTIES
(MINIMUM)
Material Type Tensile PSI Yield PSI
Carbon Steel 130,000 97,500
304 SS 90,000 50,000
316 SS 90,000 50,000
410 SS 125,000 95,000
Steel
Thknss
#6-20
DP2
#8-18
DP2
#10-16
DP3
#12-14
DP3
#12-24
DP5
1/4-14
DP3
1/4-20
DP4
(Lapped)
26 ga 278 294
24 ga 466 496
22 ga 526 560
20 ga 758 740 728 769 930
18 ga 845 1060 1266 1358 1442
16 ga 1540 1620 2100
14 ga 1552 1970 2584
12 ga 1986 2650 2650 2650
1/8”
1/4” 3310 2820
BLAZER ® drilling fasteners are
manufactured and tested to conform
to SAE J-78 for self-drilling fasteners.
Disclaimer: All test results and specifications are based on laboratory tests.
Appropriate safety factors should be used by the user or specifier. Determining
the proper fastener is the responsibility of the user or specifier. Because
application conditions vary, we assume no liability for the use of this information.
(800) 486-1832 www.trianglefastener.com
12

CONCEALOR LOW PROFILE CLIP FASTENER
Wood or Light Gauge Metal
A
#2 Combo
Square/Phillips
Recess Drive
ONCEALOR
LOW PROFILE FASTENERS
B
C
D
E
F
G
H
I
The largest selection of
low profile pancake head fasteners!
A
B
C
D
E
F
G
H
I
Sizes
Description
#10-13 X 1" GP
.0003" Zinc and Yellow
#10-13 X 1" GP LL
Long-life TRI-ACQ coated
#10-13 X 1" GP
302 Stainless Steel
#10-9 X 1-1/8" ULP
.0003" Zinc and Yellow
#10-9 X 1-1/8" ULP LL
Long-life TRI-ACQ TM Coated
#10-9 X 1-1/8" ULP
410 Stainless Steel
#10-13 X 1-1/2" GP
.0003" Zinc and Yellow
#10-13 X 2" GP
.0003" Zinc and Yellow
#12-14 X 1" GP LL
Long-Life TRI-ACQ TM Coated
Drilling
Thickness
Part
Number
Carton
Quantity
WT
Per M Pcs

CONCEALOR LOW PROFILE CLIP FASTENER
Fasten into metal or wood
#14 DP1 CONCEALOR is engineered to
perform in a variety of applications. Special
buttress thread form provides exceptional
clamping loads and resists loosening compared
to ordinary thread forms. Specified in many
metal roofing systems to attached SSR clips
over rigid insulation into metal deck. FM
approved for preliminary attachment of nail
base insulation without the use of stress
plates.
Here is why we use a special thread...
CONCEALOR with
Buttress Thread
Ordinary Thread
Form
Sizes
Description
ONCEALOR
LOW PROFILE FASTENERS
Drilling
Thickness
Part
Number
Carton
Quantity
WT
Per M Pcs
#14-13 X 1-1/2" DP1 14 ga. Max 141500C1 2,500 pcs 14.0#
#14-13 X 2" DP1 14 ga. Max 142000C1 1,000 pcs 18.0#
#14-13 X 3" DP1 14 ga. Max 143000C1 1,000 pcs 26.0#
#14-13 X 4" DP1 14 ga. Max 144000C1 1,000 pcs 29.5#
#14-13 X 4-1/2" DP1 14 ga. Max 144500C1 1,000 pcs 36.5#
#14-13 X 5" DP1 14 ga. Max 145000C1 1,000 pcs 40.0#
#14-13 X 6" DP1 14 ga. Max 146000C1 1,000 pcs 47.0#
“Flat” thread keeps
the joint tight
#2 Square
Recess Drive
“Tapered” thread
tends to cause the
joint to loosen
#14-13 X 7" DP1 14 ga. Max 147000C1 500 pcs 54.0#
FM Approved for attaching
nail base; no plates
required for 1-90 uplift.
Fasten into metal from 14 gauge up to 1/4”
#12 DP4 CONCEALOR Heavy Duty
fasteners can drill and tap up to 1/4” steel!
Great for heavy gauge applications
requiring a low profile head. Coated with an
epoxy finish that exceeds FM4470
specification assuring long-life corrosion
resistance.
Sizes
Description
Drilling
Thickness
Part
Number
Carton
Quantity
WT
Per M Pcs
#12-24 X 1-3/8" DP4 12 ga to 1/4" 121375C35E 2,500 pcs 16#
#12-24 X 2-3/4" DP4 12 ga to 1/4" 122750C35E 1,000 pcs 26#
#3 Square
Recess Drive
#12-24 X 3-3/4" DP4 12 ga to 1/4" 123750C35E 1,000 pcs 34#
#12-24 X 4-3/4" DP4 12 ga to 1/4" 124750C35E 1,000 pcs 40#
#12-24 X 5-3/4" DP4 12 ga to 1/4" 125750C35E 1,000 pcs 48#
#12-24 X 6-3/4" DP4 12 ga to 1/4" 126750C35E 1,000 pcs 54#
#12-24 X 7-3/4" DP4 12 ga to 1/4" 127750C35E 1,000 pcs 62#
Special Applications
We can assemble CONCEALOR
with a bonded sealing washer that
locks out weather and looks
appealing!
Painting CONCEALOR is not a
problem with our Kalida-Kote TM
custom paint process. We can color
match to your exact requirements in 3
days or less!
(800) 486-1832 www.trianglefastener.com
14

CONCEALOR TECHNICAL DATA SHEET
Pullout
F
Pullout In Steel - Average Ultimate in Pounds (35ksi Test Material)
Pullover
F
F
F
Pullout In Wood - Average Ultimate in Pounds
Fastener
Dia. & Point
1/2"
Plywood
5/8"
Plywood
3/4"
Plywood
Wood Type
7/16"
OSB
13/32"
OSB
21/32"
OSB
2 x 4
SYP
#10-13 GP 350 390 550 234 326 352 800
#10-9 GP 362 396 558 235 331 358 810
#12-14 DP1/Lap 376 415 598 251 351 378 860
#12-14 GP 377 418 600 255 356 382 865
#14-13 DP1 407 483 625 325 367 367 440
Decking fasteners tested with full thread embedment. 2x4 SYP with 1” embedment
Steel Pullover
Thickness Results
24 ga (.024") 1,003 lbs.
22 ga (.030") 1,178 lbs.
20 ga (.036") 1,250 lbs.
Tooling
Screwgun RPM
Carbon Steel & 410SS Fasteners
2,500 RPM maximum
304 Stainless Steel Fasteners
1,000 RPM maximum
For optimal performance, use screwguns
with torque control feature. DO NOT
OVER-TORQUE FASTENERS
Fastener Strength
Fastener Diameter
& Material
Tensile
(Lbs.)
Minimum Ultimate
Shear
(Lbs.)
Torsional
(Inch-lbs.)
#10-9 / Carbon 1,520 1,150 60
#10-9 / 410SS 2,500 1,625 85
#10-13 / Carbon 1,725 1,125 60
#10-13 / 304SS 1,040 701 45
#10-16 / Carbon 2,100 1,400 61
#10-16 / 410SS 3,200 2,130 92
#12-14 / Carbon 2,778 2,000 100
#12-14 / 304SS 2,630 1,978 85
#12-24 / Carbon 3,450 2,420 110
1/4-14 / Carbon 4,275 2,600 150
#14-13 / Carbon 3,620 2,630 115
Fastening Tips
A minimum of three (3) factors of safety should be used for most self-drilling or self-tapping
fasteners. Consult a design professional for appropriate values.
Install fastener perpendicular to the work surface and tighten to no more than
approximately 70% of the torsional strength.
Allow at least two full threads to extend beyond the material. For wood applications, allow
1” minimum embedment or full thread embedment in plywood and OSB for optimal pullout
resistance.
Fastener Properties
Thread Type
and Point
Thread
Major Dia.
Material
Head
Dia.
Head
Thickness Drive Finish
#10-16 DP2 .180" C1022 .435" .080" #2 Sq/Phil .0003" Zinc & Yellow
#10-24 DP3 .185" C1022 .435" .080" #2 Sq/Phil .0003" Zinc & Yellow
#10-13 GP .190" C1022 .450" .080" #2 Sq/Phil
.0003" Zinc & Yellow
Option:TRI-ACQ Coated
304 SS .450" .080" #2 Sq/Phil Passivated
#10-16 DP3 .180" C1022 .450" .080" #2 Sq/Phil .0003" Zinc & Yellow
410 SS .450" .080" #2 Sq/Phil Passivated
#10-9 GP (ULP) .200" C1022 .435" .040" #2 Sq/Phil
.0003" Zinc & Yellow
Option:TRI-ACQ Coated
410 SS .435" .040" #2 Sq/Phil Passivated
#12-14 GP .220" C1022 .450" .080" #2 Sq/Phil
.0003" Zinc & Yellow &
TRI-ACQ Coated
304 SS .450" .080" #2 Sq/Phil Passivated
#12-14 DP1 .210" C1022 .450" .080" #2 Sq/Phil .0003" Zinc & Yellow
#12-14 DP3 .210" C1022 .450" .080" #2 Sq/Phil
.0003" Zinc & Yellow
Option:TRI-ACQ Coated
(SD300) 304 SS .500" .090" T-25 Torx .0003" Zinc & Clear
#12-24 DP4 .210" C1022 .425" .110" #3 Sq .001" Black Epoxy
#14-13 DP1 .238" C1022 .500" .090" #2 Sq .001" Black Epoxy
1/4-14 DP3 .245" C1022 .500" .080" #2 Sq/Phil .0003" Zinc & Yellow
Corrosion Resistance
TRI-ACQ TM Long-life
Coating / Corrosion test
results in ACQ lumber
“Standard Plating”
TRI-ACQ TM Coating
1,000 hrs salt spray
ACQ lumber decking boards
ACQ Lumber Information
As recommended by the Southern Pine Council
(SPC) and recognized by the NRCA, the following
fasteners are acceptable for use in ACQ pressure
treated lumber;
Hot-dipped galvanized complying with
ASTM A153,
or coated with proprietary anti-corrosion
coatings like our TFC TRI-ACQ TM .
For maximum corrosion protection,
fasteners made of 302, 304, or 316
stainless steel should be considered.
Finish and Corrosion Test Data
Carbon Steel Fasteners
Coating
Salt Spray
.0003” min zinc and yellow 48 hrs
BLACK EPOXY
(Exceeds FM 4470)
TRI-ACQ TM Long Life
(ASTM B117)
1,000+ hrs
1,000+ hrs
DISCLAIMER: All data and specifications are based
on laboratory tests. Appropriate safety factors should
be used by the user or specifier. Determining the
proper fastener is the responsibility of the user or
specifier. Because application conditions vary, we
assume no liability for the use of this information.
15
TRIANGLE FASTENER CORPORATION

TEKS ® CARBON SELF DRILLING FASTENERS
HEAVY DUTY
APPLICATIONS
First in performance!!
Over 30 years of
consistent
drilling.
The original
self-drillers
for heavy duty
applications.
APPLICATIONS
• Metal deck to structural steel or bar joist.
• Clips to structural steel or bar joist.
• Liner panels to structural steel or bar joist.
• Accessories to structural steel or bar joist.
• Longer length fasteners can be used in
retrofit clip and sheet applications.
CORROSION RESISTANCE
Kesternich Results (DIN 50018, 2.0L)
• 30 Cycles - 10% or less red rust
Salt Spray Results (ASTM B117)
• 720 hours - 10% or less red rust
SELECTOR GUIDE
Drill Max.
Part Head Drill & Tap Material
Number Description Style Point Capacity Attachment Applications
1088000B 12-24 x 7/8'' HWH #4 .125-.250 .325
1414000 12-24 x 1-1/4'' HWH #4.5 .125-.375 .575
• Metal deck, clips,
liner panels or
accessories to
structural steel
or bar joist.
1006000B 12-24 x 1-1/4'' HWH #5 .125-.500 .375
1070000 12-24 x 1-1/2'' HWH #5 .125-.500 .625
1072000 12-24 x 2'' HWH #5 .125-.500 1.125
1074000 1/4-28 x 3'' *HWH #5 .125-.500 2.150
1075000 1/4-28 x 4'' *HWH #5 .125-.500 3.150
1641000 1/4-28 x 5'' HWH #5 .125-.500 4.150
1431000 1/4-28 x 6" HWH #5 .125-.500 5.150
1590000 1/4-28 x 8" HWH #5 .125-.500 7.150
B Now available in small box packaging * 5/16” Across Flats HWH. All available with bonded washer.
PRODUCT FEATURES
• Unique double fluted point has precise cutting edges to
improve drill performance in 1/4'' thru 1/2'' steel.
• Engineered for fast drilling and smooth tapping
with less effort.
• Climaseal ® finish provides excellent corrosion resistance
and lower tapping torque.
• Attachments up to 7.2'' of material including 1/2'' steel.
• 1/4 Diameter has notched threads
to reduce tapping torque.
• Longer fasteners
can be used in
retrofit clip and
sheet applications.
APPLICATIONS
• Plywood roof and floor sheet
to steel frames.
• 2 x 4 headers to steel frames.
• Plywood fascia to steel frames.
• Wood mansard to steel frames.
CORROSION RESISTANCE
Kesternich Results (DIN 50018, 2.0L)
• 15 Cycles - 5% or less red rust
Salt Spray Results (ASTM B117)
•300 hours - 10% or less red rust
WOOD-TO-METAL
FASTENERS
No pre-drilling, fast,
efficient attachment
of wood to steel.
SELECTOR GUIDE
Wood
Part Head Drill Drill & Tap Attachment Applications
Number Description Style Point Capacity Range
1077000 10-24 x 3/4" Wafer #3 .036-.175 1/4''-3/8''
1079000 10-24 x 1" Wafer #3 .036-.175 1/4''-1/2''
1082000 10-24 x 1-7/16" PFH #3 .060-.175 1/4''-3/4''
1087000 10-16 x 1-13/16" PFH** #3 .030-.175 1/4''-3/4''
1791000 10-16 x 1-13/16'' PSD Flat** #3 .030-.175 1/4''-3/4''
1588910 #2 PSD Bit
1800910 T-30 Bit
1092000 12-24 x 2-1/4" PFH* #4 .125-.250 3/4''-1-3/8''
1783100 12-24 x 2-1/4'' 6-Lobe Flat* #4 .125-.250 3/4''-1-3/8''
1094000 12-24 x 2-3/4" PFH* #4 .125-.250 3/4''-1-5/8''
1784100 12-24 x 2-3/4'' 6-Lobe Flat* #4 .125-.250 3/4''-1-5/8''
1096000 1/4-20 x 3" PFH* #4 .125-.250 3/4''-2''
1785100 1/4-20 x 3'' 6-Lobe Flat* #4 .125-.250 3/4''-2''
*with wings **with ribs under head Now available in small box packaging.
PRODUCT FEATURES
• Point has precise cutting edges to improve
drill performance with less effort.
• Special winged fasteners ream a hole in wood
preventing thread engagement during drilling.
• New Phillips Square Driv ® and 6-Lobe drive systems provide
superior installation stability and cam-out resistance.
• Wafer head design has a large bearing surface ideal for plywood.
• Flat head design countersinks and seats flush in wood.
• Plywood, mansard,
fascia, roofing, flooring
to steel framing.
• Plywood, 2 x 4’s
headers to steel
framing.
• 2 x 4’s to
steel framing.
Need a 1/4” diameter
fastener to attach wood to
light gauge metal?
Use our HEADER LG to
fasten to 18 gauge or less!
See page 10.
• Gray Spex finish provides excellent corrosion
resistance and lower tapping torque. Formulated for use in ACQ lumber!
(800) 486-1832 www.trianglefastener.com
16

TEKS ® CARBON SELF DRILLING FASTENERS
CORROSION RESISTANCE
INTERIOR
INSULATION
FASTENERS
The only self-driller
designed for this
unique application.
Kesternich Results (DIN 50018, 2.0L)
• 30 Cycles - 10% or less red rust
Salt Spray Results (ASTM B117)
• 720 hours - 10% or less red rust
APPLICATION
• Interior rigid and/or
blanket insulation to
steel frame.
HEAD STYLE
• Maxiseal Hex
Washer Head with
Polyethylene Washer
SELECTOR GUIDE
Drill
Part Head Drill & Tap Insulation
Number Description Style Point Capacity Range Applications
1033200 12-14 x 1-7/8'' HWH #3 .036-.210 3/4'' to 1''
1035200 12-14 x 2-3/8'' HWH #3 .036-.210 1-1/8' to 1-1/2''
1037200 12-14 x 3-1/4'' HWH #3 .036-.210 1-5/8'' to 2-3/8''
1039200 12-14 x 4'' HWH #3 .036-.210 2-1/8'' to 3''
PRODUCT FEATURES
• Large polyethylene washer prevents overdriving and pullover.
• Point has precise cutting edges to improve drill
performance with less effort.
• Non-walking point provides fast material engagement.
• Point to thread design maximizes pullout performance
and minimizes back out.
• Fastens the broadest range of insulation.
• White polyethylene washer matches insulation facers.
• Interior Rigid
Insulation to
Steel Frame
EXTERIOR RIGID
INSULATION
APPLICATIONS
The original self-drilling
fasteners designed
specifically for rigid
insulation.
SELECTOR GUIDE
Drill &
Part Head Drill Tap Insulation
Number Description Style Point Capacity Range Applications
Maxiseal ®
1034000 12-14 x 1-7/8" HWH #3 .036 - .210 3/4" to 1"
1036000 12-14 x 2-3/8" HWH #3 .036 - .210 1-1/8" to 1-1/2"
1038000 12-14 x 3-1/4" HWH #3 .036 - .210 1-5/8" to 2-3/8"
1040000 12-14 x 4" HWH #3 .036 - .210 2-1/8" to 3"
Scots ®
1169200 12-14 x 1-7/8" HWH #3 .036 - .210 3/4" to 1"
1170200 12-14 x 2-3/8" HWH #3 .036 - .210 1-1/8" to 1-1/2"
1171200 12-14 x 3-1/4" HWH #3 .036 - .210 1-5/8" to 2-3/8"
1172200 12-14 x 4" HWH #3 .036 - .210 2-1/8" to 3"
• Roof and wall
panel over rigid
insulation to
steel framing.
• Roof panel over
spacer block and
insulation to eave
purlin.
PRODUCT FEATURES
• Unique rider section stops panel jacking, point burnout and breakage.
• High thread under the head prevents panel strip out.
• Improved in place aesthetics.
• Available in Scots ® and Maxiseal ® head styles.
• Maximum pullover performance.
• Excellent driving stability.
• Seals when driven at an angle.
• Fastens the broadest range of insulation thickness.
• Point has precise cutting edges to improve drill performance with less effort.
• Non-walking point provides fast material engagement.
• Point to thread design maximizes pullout performance and minimizes back out.
• Climaseal ® finish provides excellent corrosion resistance and lower tapping torque.
HEAD STYLES
Maxiseal Head
Scots Head
17
TRIANGLE FASTENER CORPORATION

MAXISEAL
METAL ROOF & WALL APPLICATIONS
MAXISEAL Integral Washer System
Maxiseal ... The premium sealing system for Teks ®
self-drilling, self-tapping fasteners.
SELECTOR GUIDE
APPLICATIONS
• Roof panel to purlin and wall panel to girt.
• Stitching roof, wall, fascia, eave panels
or gutter straps.
• Roof and wall panel or accessories over
blanket insulation to steel framing.
• #17 diameter replacement for stripped
#12 and 1/4 diameter fasteners.
Drill Max.
Part Head Drill & Tap Material
Number Description Style Point Capacity Attachment Applications
1376000 10-16 x 3/4” HWH #3 .036-.175 .325
• Roof and wall panel
to steel framing.
1023000 12-14 x 3/4” HWH #3 .036-.210 .260
1026000 12-14 x 1” HWH #3 .036-.210 .490
1029000 12-14 x 1-1/4” HWH #2 .036-.210 .560
1428000 12-14 x 1-1/2” HWH #2 .036-.210 .790
1730000 12-24 x 7/8'' HWH #4 .018-.250 .295
1517000 12-24 x 1-1/2'' HWH #5 .125-.500 .500
1389000 1/4-14 x 7/8” HWH #1 .018-.095 .320
1042000 1/4-14 x 3/4” *HWH #3 .036-.210 .200
1044000 1/4-14 x 1” *HWH #3 .036-.210 .310
1048000 1/4-14 x 1-1/2” *HWH #3 .036-.210 .810
1737000 1/4-14 x 1-3/4'' *HWH #3 .036-.210 1.060
1712000 1/4-14 x 3” HWH #3 .036-.210 2.310
1060000 1/4-14 x 3/4” HWH AB - .435
1063000 17-14 x 1” HWH AB - .685
Now available in small box packaging.
• Panel over insulation
to steel framing.
• Roof and wall panel to
bar joist or structural.
• Stitching roof, wall, fascia,
eave panels or gutter straps.
• Sheet or accessories
with up to 6” blanket
insulation to steel framing.
• Replacement screw for 12
and 1/4'' diameter fasteners
CORROSION RESISTANCE
Kesternich Results (DIN 50018, 2.0L)
30 Cycles - 10% or less red rust
Salt Spray Results (ASTM B117)
720 hours - 10% or less red rust
(800) 486-1832 www.trianglefastener.com
18

SCOTS
LONG-LIFE TEKS FASTENERS
SCOTS
Long Life Teks Fasteners
Scots 300 Stainless
Steel will never
rust... ever!!!
PRODUCT FEATURES
• For improved appearance and extra life
an integral design controls the EPDM washer.
• Combines 300 series stainless steel exterior
with the strength of carbon steel.
• 300 series stainless most preferred for galvalume long life panels.
• Maximum sealing and corrosion protection.
• Point has precise cutting edges to improve drill performance
with less effort.
• Non-walking point provides fast material engagement.
• Point to thread design maximizes pullout performance
and minimizes backout.
• Drills and taps in the broadest range of applications.
SELECTOR GUIDE
Drill Max
Part Head Drill & Tap Material
Number Description Style Point Capacity Attachment Applications
1165253 12-14 x 1'' HWH #2 .036-.210 .310
• Panel over blanket insulation
1167253 12-14 x 1-1/4'' HWH #2 .036-.210 .560 to steel frame.
1168253 12-14 x 1-1/2'' HWH #2 .036-.210 .790
1163000 12-24 x 2'' HWH #5 .125-.500 1.000 • Roof curb to structural steel
1788000 1/4-28 x 4'' HWH #5 .125-.500 3.000
1387253 1/4-14 x 7/8'' HWH #1 .018-.095 .320 • Stitch roof and wall sidelaps.
1175153 1/4-14 x 1-1/8'' HWH #1 .018-.095 .395
SR endlaps.
• Standing seam roof
1616000 1/4-14 x 1-1/4'' HWH #3 .036-.210 .630 system endlaps.
1178253 1/4-14 x 3/4'' HWH AB - .435 • Replacement screw for 12
1701000 1/4-14 x 1-1/2'' HWH AB - .870 and 1/4'' diameter fasteners
1180225 17-14 x 1'' HWH AB - .686
1625053 17-14 x 1-1/4'' HWH AB - .935
APPLICATIONS
• Panel over blanket insulation to steel frame.
• Roof curb to structural steel.
• Standing seam roof system endlaps.
• Stitch roof and wall sidelaps.
• #17 diameter replacement screw for
#12 and 1/4 diameter fasteners.
HTZ HIGH TORQUE ZINC LONG LIFE TEKS ® FASTENERS
PRODUCT
SPECIFICATIONS
Diameter . . . . . . .#12, 14
Thread Form . . . . .12-14, 1/4-14
Point Type . . . . . . .Teks 1, Teks, 2,
. . . . . . . . . . . . . . .Type AB
Finish . . . . . . . . . .Silver Climaseal ®
. . . . . . . . . . . . . . .Head Paint
. . . . . . . . . . . . . . .available
SELECTOR GUIDE
Drill & Max.
Part Head Drill Tap Material
Number Description Style Point Capacity Attachment Applications
1727053 12-14 x 1'' HWH Teks/2 .036-.210 .310
1725053 12-14 x 1-1/4'' HWH Teks/2 .036-.210 .560
1729053 12-14 x 1-1/2'' HWH Teks/2 .036-.210 .790
1721053 1/4-14 x 7/8'' HWH Teks/1 .024-.095 .320
1723053 1/4-14 x 1-1/4'' HWH Teks/2 .036-.210 .630
PANEL OVER BLANKET
TO STEEL FRAME.
STITCH ROOF AND
WALL SIDE LAPS.
• PANEL OVER BLANKET
TO STEEL FRAME.
• STANDING SEAM ROOF
SYSTEM ENDLAPS.
HEAD STYLES
5/16'' HWH zinc-aluminum alloy with
integral washer design.
1736053 1/4-14 x 1'' HWH Type AB ------------- .686
• REPLACEMENT SCREW
FOR 12 DIAMETER
FASTENERS.
• PANEL OVER BLANKET
TO STEEL FRAME IN
PREDRILLED APPLICATIONS.
PRODUCT FEATURES
• HTZ fasteners have the highest torsional head strength
values
in the industry ... no head failures.
• Zinc aluminum alloy head gives premium corrosion
resistance ... no red rust.
• ”No mar” radius washer design will not scratch,
pierce or damage panels if over driven.
• For improved appearance and extra life an integral design
controls the EPDM washer ... maximum sealing protection.
• Point has precise cutting edges to improve drill
performance with less effort.
• Non-walking point provides fast material engagement.
• Point-to-thread design maximizes pullout
performance and minimizes back out.
• Drills and taps in the broadest range of applications.
19
TRIANGLE FASTENER CORPORATION

CARBON SELF DRILLING FASTENERS
Technical Data
SHEET STEEL GAUGES
Gauge No. 12 14 16 18 20 22 24 26
Decimal Equivalent .105” .075” .060” .048” .036” .030” .024” .018”
FASTENER VALUES
Fastener Tensile Shear Torque
(dia-tpi) (lbs.-min.) (avg. lbs.ult.) (min.in.lbs.)
TEKS ® Heavy Duty
12-24 T/4 3020 2100 100
12-24 T/4.5 3165 2200 150
12-24 T/5 3188 2200 150
1/4-28 T/5 5577 3310 234
TEKS ® Wood To Metal Fasteners
10-16 1936 1400 61
10-24 2702 1500 65
12-24 3165 2200 150
1/4-20 3860 2700 168
TEKS ® Interior and Exterior Fasteners
12-14 2778 2000 90
MAXISEAL , SCOTS, HTZ
10-16 1936 1400 61
12-14 2778 2000 92
12-24 T/4 3020 2100 100
12-24 T/5 3188 2200 150
1/4-14 4060 2600 150
17-14 5300 3200 180
PULLOUT VALUES (AVERAGE LBS. ULTIMATE)
Dia. Pt. 26 24 22 20 18 16 14 12 3/16 1/4
TEKS ® Heavy Duty
Fastener
Steel Gauge
4 – – 1532 3485 4013
12 4.5 – – 1508 3865 4101
5 – – 1527 3701 3999
1/4 5 – – 1507 3300 5059
TEKS ® Wood To Metal Fasteners
Fastener
Steel Gauge
#10-16 3 – 208 266 299 499 708 967 1474 – –
#12 4 – – – – – 683 923 1508 3865 4101
1/4 4 – – – – – 788 1116 1803 4297 –
TEKS ® Interior and Exterior Insulation Fasteners
Fastener
Steel Gauge
12 3 142 211 289 341 551 757 1063 1631 2998
MAXISEAL , SCOTS, HTZ
Fastener
Steel Gauge
10 3 124 208 266 299 499 708 967 1474 – –
12 2 156 243 283 375 605 848 1181 1856 3520 –
3 142 211 289 341 551 757 1063 1631 2998 –
4 – – – – – 697 986 1532 3485 4013
5 – – – – – – – 1527 3701 3999
1/4 1 208 329 428 562 800 1151 – 1858 4550 –
3 141 231 293 346 613 880 1145 1690 3446 –
AB 235 365 496 597 702 926 1180 1716 3523 –
17 AB 225 261 350 442 553 752 1122 – – –
SHEAR VALUES (AVERAGE LBS. ULTIMATE)
Dia. Pt. 26 24 22 20 18 16 14 12 1/8 1/4
TEKS ® Heavy Duty
Fastener
Steel Gauge (lapped)
4 – – 2048 2030 –
12 4.5 – – 2641 2887 2897
5 – – 2650 2700 2762
5 1597 2005 2350 2792 3310
TEKS ® Wood to Metal Fasteners
Fastener
Steel Gauge (lapped)
#10 3 728 1266 1540 1522 – –
#12 4 – – – – 2148 2030
#1/4 4 – – – – 2650 2820
TEKS ® Interior and Exterior Fasteners
Fastener
Steel Gauge (lapped)
12 3 – – – 769 1358 1620 1970 1986
MAXISEAL , SCOTS, HTZ
Fastener
Steel Gauge (lapped)
#10 3 – 445 526 728 1266 1540 1552 –
2 365 600 623 898 1370 1758 2138 –
#12 3 – – – 769 1358 1620 1970 1986
4 – – – – – – – 2048
5 – – – – – – – 2650
1 511 849 885 1244 1765 – – –
1/4 3 – – – 930 1442 2100 2584 2650
AB 422 482 669 889 1157 – – –
#17 AB 459 745 989 958 1415 – – –
(800) 486-1832 www.trianglefastener.com
20

SFS INTEC ZAC ZINC HEAD FASTENERS
SELECTION GUIDE
INTEC Pcs. Weight
Part HWH Per Std. Lbs. Per
Size Type No. Size Carton M Pcs.
12 x 3/4” Sharp Point A1653-FL 3/8" AF 2500 19.1
14 x 3/4” AB A4365-FM 3/8" AF 2500 24.5
14 x I” M/P A A3325-FM 3/8" AF 2000 25.0
14 x 1” M/P AB A4395-FM 3/8" AF 2000 24.6
14 x 1 1/2” M/P AB A4485-FM 3/8" AF 2000 28.2
14 x 2” M/P AB A4513-FM 3/8" AF 1500 32.8
14 x 2 1/2” M/P AB A4510-FM 3/8" AF 1500 37.6
17 x 1” AB A6045-LF 3/8" AF 2000 24.1
17 x 1 1/2” AB A6066-LF 3/8" AF 1500 29.9
12-14 x 1” Impax S/D S4576-FL 3/8" AF 2000 21.5
12-14 x 1 1/4” Impax S/D S4631-FL 3/8" AF 2000 23.8
12-14 x 1 1/2” Impax S/D S4676-FL 3/8" AF 1500 25.5
12-14 x 2” Impax S/D S4776-FL 3/8" AF 1000 29.7
12-14 x 2 1/2” Impax S/D S4901-FL 3/8" AF 1500 32.6
12-14 x 3” Impax S/D S4951-FL 3/8" AF 1250 36.2
1/4-14 x 7/8” Lap Impax S5065-FM 3/8" AF 2000 21.7
1/4-14 x 1 1/4” #2 Self-Drill S5195-FM 3/8" AF 2000 28.6
1/4-14 x 1 1/2” #2 Self-Drill S5287-FM 3/8" AF 1500 31.2
12-24 x 1 1/4” Impax 45 S4665-FL 3/8" AF 2000 24.3
12-24 x 1 1/4” Impax 5 S4669-FL 3/8" AF 1500 28.7
12-24 x 1 1/2” Impax 5 S4742-FL 3/8" AF 1500 27.5
Call TFC for all the latest sizes
and types of long life fasteners
for commercial roofing!
Available in 5/16” hex.
21
TRIANGLE FASTENER CORPORATION

FASTENERS FOR CONSTRUCTION
FLAT-TOP DRILLING
& SELF TAPPING FASTENERS
• Carbon Steel. .0005 Mm. Mechanical Zinc Plated
• With Under-Cut Hex Heads and EPDM Sealing Washers
• OxySeal II Long-Life Coating
• Self-Tapping and Tapered Compression Points
• Socket Support
• Deeper Undercut to Entrap Sealant
Flat-Top head fasteners combine undercut hex washer heads
with EPDM cut-tubular sealing washers. They are a costeffective
alternative to metal-backed washers in some
applications.
CARBON STEEL AND 410 STEEL
• Flat-top design stabilizes socket during installation
• Higher hex provides positive socket engagement
• Special undercut entraps EPDM sealing washer,
even when driven at extreme angles
• One piece flat-top design eliminates damage to
painted washer surface and eliminates dissimilar
metal washer materials
DECIMAL (INCH)
EQUIVALENTS
OF THREAD
DIAMETERS
DECIMAL (INCH)
EQUIVALENTS
OF SHEET
METAL GAUGES
Thread Decimal Thickness
Diameter Equivalent Gauge (in.)
#6 .140 26 .018
#7 .150 24 .024
#8 .160 22 .030
#9 180 20 .036
#lO .190 18 .048
#11 200 16 060
#12 .210 14 .075
#13 .230 12 .105
1/4” .240 10 .134
#14 .250 8 .164
#17 .285 4 .224
#18 .304 1/4 .250
11/32” .344
Size
Point
Stitch/Lap Point
1/4-14 X 7/8" TCP1
#2 Long Pilot Point
#12-14 x 1" TCP2
#12-14 x 1 1/4" TCP2
#12-14 X 1 1/2" TCP2
#12-14 x 2 TCP2
1/4 -14 x 1" TCP3
1/4 -14 x 1 1/4" TCP3
PULL-OVER VALUES
GAUGE
Fastener 22 24 26
Diameter (.030) (.023) (.018)
12-14 1128 982 621
1/4 - 14 1298 1043 687
SHEAR VALUES
DRILL POINT CAPABILITIES
GAUGE
Size Point 12 14 16 18
12-14 TCP3 1634 1066 760 554
1/4 - 14 TCP3 1861 1148 883 613
Gauge
Size Point 26-26 24-24 22-22 20-20 18-18 16-16 14-14 12-12 1
/8 - 1 /8
• Higher hex point provides
positive socket engagement
• Flat on top stabilizes socket
during installation
• Special undercut entraps
sealant… even when driven
at angles
• EPDM Sealant assures
waterproof seal even
under harsh conditions
• Standard OxySealII
long-life coating for
added corrosion
protection on carbon
steel fasteners.
Size
Point
Self Tapping
14 x 3/4" AB
14 x 1" AB
14 x 11/2" AB
14 x 2" AB
17-14 x 1" AB
STRENGTH CHARACTERISTICS
Minimum Min. Fastener Fastener
Fastener Tensile Torque Strength Shear
Size (pounds) (inch-pounds) (pounds)
12-14 1128 92 2,000
1/4 - 14 3,850 150 2,600
12-14 T/1 435 706 756 1021 1455 – – – – – –
1/4 - 14 T/1 514 852 888 1247 1757 – – – – – –
8-18 T/2 297 499 563 743 1063 1081 – – – – –
10-16 T/2 315 481 592 833 1209 1271 – – – – –
12-14 T/2 368 603 626 901 1373 1761 2141 – – – –
8-18 T/3 – – – 733 1093 1213 1217 – – – –
10-16 T/3 – – – 731 1269 1543 1555 – – – –
10-24 T/3 – – – 754 1211 1557 1697 – – – –
12-14 T/3 – – – 772 1361 1623 1973 1989 – – –
1/4-14 T/3 – – – 933 1445 2103 2587 2653 2823 – –
12-24 T/4 2051 2703 – –
12-24 T/5 – – – – – – – – 2703 2723 2765
3
/16 - 3 /16
1
/4 - 1 /4
(800) 486-1832 www.trianglefastener.com
22

LARGE DIAMETER SELF DRILLING FASTENERS
DRILLTITE ® LARGE DIAMETER
SELF-DRILLING FASTENERS
Carbon steel self-drilling fasteners with dual-processed point
Zinc plated, with or without bonded washers
Type 3 point, round body Taptite ® threads
Diameter/Pitch Head Style
5/16-18 x 1" 3/8" Hex Washer Head
5/16-18 x 1 1/4" 3/8" Hex Washer Head
5/16-18 x 1 1/2" 3/8" Hex Washer Head
REZTITE® FASTENERS
Improve quality in steel-framed
residential construction
Zinc and clear plated, Torx Plus ® drive
system
Round body Taptite ® threads
Packaged with one 20IP bit
per carton
0 0 drive angle
Deep engagement
depth
Maximum torque
transfer
Application Size Head Style Point Style
Steel-to-steel Steel framing fastener Indented Type 2/3
10-24 x 3/4" hex washer
Attach wall track Wall track fastener Indented Type 2/3
to floor sheathing 10-24 x 1 3/4" hex washer
to steel subfloor
Light-gage Wall stud fastener Modified truss Type 2
steel-to-steel 8-32 x 5/8"
Attach plywood sheathing Plywood flooring fastener Wafer head Type 2
(up to 3/4" thick) 8-32 x 1 1/2" with locking
to steel subfloor
serrations
Featuring Torx Plus ® drive system
The Torx Plus drive system provides an unmatched ability to increase your productivity by outperforming
competing drive systems.
• Eases installation: The unique design of the Torx Plus Drive reduces camout while requiring little or no
end load to keep the driver engaged in the recess. The 0° drive angle maximizes torque transmission.
• Minimizes damage to application: The Torx Plus recess completely encloses the driver tip, reducing tool
slippage and damage to the fastener and surrounding surfaces, which often occurs with cross-type fasteners.
• Longer drive bit life: The improved fit between fastener and tool minimizes wear on the drive bit.
Downtime and costs are reduced since significantly fewer drive bit changes are required.
23
TRIANGLE FASTENER CORPORATION

STRESSLESS FRAMING FASTENER
Oversized washer
face increases
clamp load
STRESSLESS FRAMING FASTENER
StressLess was developed specifically for metal to metal framing application
APPLICATION
Used for metal to metal applications and other high stress applications.
Radial indent on
washer face
distributes stress
PHYSICAL & MECHANICAL PROPERTIES
Description: 1/4-14 x 7/8" self-drilling fastener with radial indent under washer face.
Point Type: Type 3 self-drilling point with long pilot section.
Head Style: 5/16" Hex with oversize washer face.
Material:
01018-1022 carbon steel
Heat Treatment: Case hardened to SAE J-78 specification
Finish:
Black Epoxy (E) Coating (30 cycles Kesternich)
Long pilot section for
fastening multiple
frame thicknesses
Fastener Strength (Ultimate)
Torsional
150 inch pounds
Tensile
3850 pounds
Shear
2600 pounds
Great for fastening steel framing in
retrofit metal roof applications!
Pullout Strength in Steel
(Ultimate in Pounds)
18 ga( .O40”) 613 lbs
16 ga(.060”) 883 lbs
14 ga(.075”) 1148 lbs
12 ga(.105”) 1861 lbs
3/16” (.1875") 4553 lbs
1/4" (.250") 5036 lbs
HERE'S HOW STRESSLESS WORKS!
A special radial indent on the washer face distributes the amount of stress that normally
concentrates in the area where the threads intersects the washer face. The oversized washer
face increases clamping load by over 20% when compared to ordinary fasteners.
Stress Less
Framing Fastener
Ordinary
Fastener
Special radial indent
increases bearing surface
and and distributes stress
Radius under the fastener
head produces a
concentration of stress
Test results are based on laboratory tests. Appropriate safety factors should be used by the
user or specifier. Determining the proper fastener is the responsibility of the user or specifier.
Because application conditions vary, we assume no liability for the use of this information.
StressLess is a trade name of Triangle Fastener Corporation TFC logo is a registered
trademark of Triangle Fastener Corporation
(800) 486-1832 www.trianglefastener.com
24

SELF-TAPPING FASTENERS
SMALL DIAMETER SELF TAPPING
FASTENERS
Our small diameter self-tapping
fasteners are available in carbon
steel, 410s and 18-8SS
SMALL DIAMETER SELF-TAPPING FASTENERS
#8 diameter - Type A
Light gauge fastening - 1/4” HWH
Max Thickness Carton
Description Range Quantity
#8 x 1/2” .100 5M
#8 x 3/4” .350” 5M
#10 diameter - Type AB
Light gauge fastening - 5/16” HWH
Max Thickness Carton
Description Range Quantity
#10 x 1/2” .100” 10M
#10 x 3/4” .350” 7.5M
#12 diameter - Type AB
Light & medium gauge fastening - 5/16” HWH
Max Thickness Carton
Description Range Quantity
#12 x 3/4” .350” 2.5M
#12 x 1” .600” 2.5M
SELF TAPPING SHEETING SCREWS
Carbon Steel, 304 Stainless Steel and
410 Stainless Steel. With or without bonded sealing washers
#14-10 TYPE A
LIGHT GAUGE STEEL
AND WOOD
1/4-14 TYPE AB
STEEL OR WOOD
1/4-14 TYPE B
HEAVY GAUGE STEEL
>16GA
#17-14 TYPE AB
STEEL OR WOOD
“GOOF SCREW”
SELECTION GUIDE
Head Point
Dia. Lengths Type Type Application/Use
14-10 3/4”, 1”, 1-1/4”, 1-1/2”, 2”, 2-1/2”, 3/8" Hex A Cladding and sheet overlap (stitching),for attaching flashing,
3”, 3-1/2”, 4”, 5”, 6”, 7”*, 8”* and for attaching cladding to 18 gage and lighter framing.
1/4-14 3/4”, 1”, 1-1/2”, 2”, 2-1/2”, 3/8" Hex B The tighter thread configuration is designed for attaching
3”, 3-1/2”, 4”, 5”, 6”, 7”*, 8”* cladding to 18 gage and heavier framing members, while
the blunt point minimizes the appearance of the fastener
inside the building.
1/4-14 3/4”, 1”, 1-1/4”, 1-1/2” 3/8" Hex AB The tighter thread configuration plus pointed tip make this
ideal for aligning sheets during attachment to 18 gage
and heavier framing members.
17 -14 3/4", 1”, 1-1/2” 3/8" Hex AB The larger diameter and close thread configuration allow
greater resistance to strip-out and shear and results in
tighter overlap joints. This can also be used to replace
1/4" fasteners that have stripped through.
* 7” and 8” fastener available in 304 stainless steel only.
25
TRIANGLE FASTENER CORPORATION

TECHNICAL DATA SHEET
SELF TAPPING FASTENERS
in Carbon Steel, 304 Stainless Steel and
410 Stainless Steel. With or without bonded
sealing washers
TYPE A
TYPE AB
LIGHT GAUGE METAL METAL OR WOOD
OR WOOD
TYPE B
“HEAVY GAUGE METAL”
#17 TYPE AB
“GOOF SCREW”
Material Properties
Tensile Yield
Material Type PSI PSI
Carbon Steel 130,000 97,500
304 SS 90,000 50,000
316 SS 90,000 50,000
410 SS 125,000 95,000
PULLOUT RESULTS FOR 1/4”
SELF-TAPPING FASTENERS
(AVERAGE ULTIMATE POUNDS)
Steel Point Drill
Thickness Types Bit Pullout
26ga (.018”) A, AB R 243 lbs.
24ga (.024”) A, AB EFE
340 lbs
22ga (.030”) A, AB 372 lbs.
R
20ga (.036”) A, AB 412 lbs.
18ga (.048”) A, AB, BP T
O
518 lbs.
16ga (.060”) A, AB, B, BP 674 lbs.
D
14ga (.075”) AB, B, BP R 831 lbs.
12ga (.105”) AB, B, BP ILL 1681 lbs.
1/8” (.125”) AB, B, BP 1780 lbs.
10ga (.134”) AB, B, BP
C
1812 lbs.
3/16” (.187”) B, BP H 2855 lbs.
1/4” (.250”) B, BP
A
3355 lbs.
R
3/8” (.375”) B, BP T 3391 lbs.
1/2” (.500”) B, BP 3500 lbs.
Point
Type
Type A
Point
Fastener
Diameter
#10
#12
#14
.010”
26ga
24ga
22ga
20ga
7/64”
1/8”
1/8” 5/32”
18ga
.050”
1/8”
5/32”
3/16”
Mechanical Properties
Strengths of Carbon Steel Tapping Screws
Fastener
Diameter
Material Thickness & Drill Bit Size
16ga
14ga
13ga
.100”
12ga
11ga
Torsional
(Inch Lbs.)
10ga
.150”
8ga
Tensile
(Pounds)
3/16”
.200”
7/32”
1/4”
.300”
Shear
(Pounds)
#8-18 (.164”) 42 1575 1000
#10-16 (.190”) 61 2100 1400
#12-14 (.216”) 92 2778 2000
#12-24 (.210”) 100 3188 2100
#14-10 (*.240” ) 125 3150 2150
1/4-14 (*.242”) 142 4250 2600
1/4-20 (.250” ) 156 4275 2700
#17-14 (.285”) 170 5940 3285
5/16-12 (.312”) 290 7650 5100
11/32-12 (.344”) 400 8550 5700
23/64-12 (.359”) 425 9150 6100
5/16”
3/8”
.400”
.500”
Self-tapping Screw Gun
Recommendation: 900 RPM Max
Type AB
Point
Type B
Point
#12
1/4”
#17
11/32”
1/4”
1/8”
3/32” 11/64” 3/16”
1/8” 5/32”
#8 (.199”) #4 (.209”)
3/16”
1/4”
17/64”
19/64”
5/16”
21/64” .322”
#8 (.199”) #4 (.209”) #1 (.228”)
We stock a full line of high quality split point drill bits up to 12” long!
(800) 486-1832 www.trianglefastener.com 26

PANEL-TITE METAL-TO-WOOD FASTENERS
A FULL LINE OF FASTENERS FOR METAL-TO-WOOD APPLICATIONS
Designed for fast installation and corrosion free performance.
Panel-Tite #9, #10, and #12 are bagged at 500 pieces each...no charge!
All fasteners can be painted with our Kalida-Kote paint finish to your exact color match.
Polyurethane with UV protection provides a chip resistant finish without chalking and fading.
PANEL-TITE #9 SHARP POINT
Sharp gimlet point for fast penetration. Comes standard with TRI-
ACQ corrosion resistant long-life coating formulated for ACQ
treated lumber.
Available with a stainless steel or zinc alloy heads
and 304 stainless steel
SIZES
Size
Attachment Range
#9-15 x 1 Gimlet < .250
#9-15 x 1-1/2 Gimlet

TECHNICAL DATA SHEET
Panel-Tite Technical Data
#9
DOUBLE LEAD
#10
DUAL THREAD
#12
DIAPHRAGM
#12
LAP
#9
STAINLESS CAP
#10
ZINC CAP
#9
304 SS BI-METAL
#14
TYPE S POINT
MATERIAL
CARBON STEEL
PLATING: TRI-ACQ TM LONG-LIFE (#9)
.0005” MIN. ZINC (#10 & #14)
304 STAINLESS STEEL
.0003” MIN. ELECTRO ZINC.
HEAD STYLE: #9, #10 , #12.......1/4” HWH
#14....................5/16” HWH
POINT: PIERCING GIMLET
THREAD: #9-15 DOUBLE LEAD
#10-15 HIGH LOW
#12-14 DOUBLE LEAD
#14-10 TYPE S POINT
PAINT: KALIDA-KOTE POLYURETHANE WITH
UV stabilizer
Disclaimer: All test results and specifications are based on
laboratory tests. Appropriate safety factors should be used by the
user or specifier. Determining the proper fastener is the
responsibility of the user or specifier. Because application
conditions vary, we assume no liability for the use of this information.
ACQ Treated Lumber Information
STRENGTHS
Tensile Shear Torsional Stress
Size (lbs. min) (avg. lbs. ult.) (min. in.lbs.) Area
#9-15 CS 1,800 1,200 60 .0106 sq. in.
#9-15 SS 1,224 980 50 .0106 sq. in.
#10-15 1,850 1,216 68 .0110 sq. in.
#12-14 2,778 2,000 92 .0159 sq. in.
#14-10 3,150 2,150 125 .0182 sq. in.
CS = Carbon Seel (C1022)
SS = Stainless Steel (304)
PULLOUT VALUES IN WOOD
Pullout In Pounds
Embd
Material #9 #10 #14 Depth
2x Pine 328 3/4”
662 960 852 1”
1/2” CDX 222 312 384 full
5/8” CDX 399 446 489 full
3/4” CDX 403 492 667 full
7/16” OSB 183 250 245 full
19/32” OSB 276 365 full
23/64” OSB 261 406 full
Values good for carbon steel and 304 stainless steel.
PULLOVER STRENGTH IN POUNDS
Washer 26ga 24ga 22ga 20ga 18ga
Size (.019”) (.023”) (.031”) (.035”) (.049”)
1/2” O.D. 515 674 875 1100 1627
9/16” O.D. 587 744 915 993 1246
15mm O.D. 564 810 1097 1166 1643
CORROSION TEST RESULTS
#9 TRI-ACQ TM #10
Kesternich 30 cycles 5 cycles
Salt Spray 1,000 hours 48 hours
Fasteners for ACQ Treated Lumber
Use PANEL-TITE TM coated with
TRI-ACQ TM coating or PANEL-TITE TM
made from 304 stainless steel.
(800) 486-1832 www.trianglefastener.com 28

LELAND PLASTIC PANEL FASTENERS
MASTER ONE STEPPERS THERMAL EXPANSION FASTENERS
FOR PLASTIC PANEL APPLICATIONS
Substrate to WOOD Structural Frame with Expansion Hole
Revolutionary design, self drills expansion hole, automatically centers screw in expansion hole,
sealing washer allows installed panels to float in a ONE STEP operation.
SIZES
Dia. Lengths
# 12 1 1/4”, 1 1/2”, 1 3/4”, 2”, 2 1/4”, 2 1/2”
• All Master One Steppers are #12 (11) diameter with sharp piercing points.
• Available with either Hex Washer Heads (1/4 AF) or Low Profile Pancake
Heads (7/16 O.D.) Quadrex drive - use Phillips or square drive bits.
• Hex Washer Head One Steppers are assembled with Master Seal®
14 mm / 1/2” O.D. aluminum vulcanized washers .
• Low Profile Pancake Head One Steppers are assembled with 12 mm / 1/2”
O.D. cushioning washers .
• Fastens substrate thicknesses from .030 to .750.
• Manufactured from Case Hardened Steel with JS500 coating
(500 Hours Salt Spray).
• Manufactured from Case Hardened Steel with DT2000 coating
(2000 Hours Salt Spray).
• Manufactured from 304 HT High Tensile Stainless Steel.
Master One Steppers are packaged in a square plastic pail with strong metal carrying handle and
feature a ‘Tab-Lok’ security lid. The container is attractively labeled on one side and clearly
displays all pertinent information.
MASTER SEAL ®
SEALING WASHER
Provides a cushioned expansion.
No Leaks
STAINLESS
304 HT High Tensile Stainless up to
4” length from stock.
No Rust
STANDARD COATING
Withstands 500 Hours Salt Spray
test and 5 cycles in the SO2 Kesternich test.
No Red Rust
FIVE
SUBSTRATE THICKNESSES
up to .100/.250/.375/.500/.750
No Rust
LONGLIFE COATING
Withstands 2000 Hours Salt Spray
test and 30 cycles in the SO2 Kesternich
test.
No Red Rust
HEAD TYPES
1/4” Hexwasher head Low Profile
Pancake head.
No Rust
PAINTING
Colors to match any roofing or siding.
No Rust
FRP PANELS PVC PANELS
CORRUGATED PANELS FLUTED/CORED
PANELS
DISCLAIMER: All test results and suggestions are based on laboratory tests. Specific job site conditions should be taken into
consideration when specifying the proper fastener. Because application conditions vary, we assume no liability for use of this information.
Master Seal is a registered trademark of Aztec Washer Company, Inc. PATENT PENDING
FIBER CEMENT PANELS
29
TRIANGLE FASTENER CORPORATION

OVERSIZED TAPPING SCREWS
SCRU-BOLT ® FASTENERS
To ease the installation of standing seam
roofs Scru-Bolt® fasteners are self-tapping
screws developed with Butler®
Manufacturing for attaching standing seam
roofing panel clips to pre-punched framing
members, or attaching panels to secondary
structural members.
• Type AB point and self-tapping thread
• Available in carbon steel or stainless steel
• Hex washer head or Torx ® truss head
• Bonded Weath-R-Seal washer
• High-quality, tapping lead threads ease installation
• Larger-than-standard diameter provides additional shear strength
• Type AB point, assembled with bonded Weath-R-Seal ® washer
Diameter Washer Size Head Style Wt./M
Carbon Steel
23/64" X 1" .729” Hex Washer 32
23/64" X 1 1/4" .729” Hex Washer 37
23/64" X 2" .729” Hex Washer 55
23/64" x 2 1/4" .729” Hex Washer 60
23/64" x 2 3/4" .729” Hex Washer 70
23/64" x 3 1/2" .729” Hex Washer 88
23/64" x 5" .729” Hex Washer 121
23/64" x 6" .729” Hex Washer 144
11/32" x 7/8" 9/32” Torx ® Truss 26
11/32" x 1 1/2" 9/32” Torx ® Truss 38
11/32" x 2" 9/32” Torx ® Truss 48
410 Stainless Steel
11/32" x 7/8" .729” Hex Washer 26
11/32" x 1 1/4" .729” Hex Washer 32
11/32" x 2 3/4" 1” Hex Washer 61
23/64" x 1" .729” Hex Washer 31
Scru-Bolt Nut
11/32" - 12 n/a n/a 6
(800) 486-1832 www.trianglefastener.com 30

DECK-IT WOOD DECKING SCREWS
Full line of high performance wood deck fasteners
SIZES
COARSE THREAD - TRI-ACQ COATED
• Exterior wood screw for outdoor applications including desks, treated wood,
patios and fencing.
• TRI-ACQ coated formulated for ACQ treated lumber!
Carton Drive Carton
Size Quantity Style Weight (lbs.)
6 x 1” 10M + 32
6 x 1 1/4” 8M +/ 30
6 x 1 5/8” 5M +/ 24
6 x 2” 3.5M +/ 21
8 x 2 1/2” 2.5M +/ 24
8 x 3” 2M +/ 24
10 x 3 1/2” 1.5M +/ 28
10 x 4” 1M +/ 24
10 x 5” 1M + 27
10 x 6” 1M + 30
305 STAINLESS STEEL
• 305 stainless steel coarse thread deck screw, square drive, type 17 point with
nibs.
• Exterior wood screw for outdoor applications including desks, treated wood,
patios and fencing applications that require a high degree of corrosion resistance.
• For best possible corrosion resistance in ACQ Treated Lumber!
• Type 17 point provides superior penetration through the hardest of woods.
• 305 stainless steel provides maximum strength with superior corrosion protection.
Size Ctn. Qty. Ctn. Wgt.(lbs.)
8 x 1 1/4” 5M 28
8 x 1 5/8” 4M 29
8 x 2” 3M 25
10 x 2 1/2” 2M 25
10 x 3” 1.5M 23
10 x 3 1/2” 1M 18
COMPOSITE DECK SCREWS - TRI-ACQ COATED
•For flush mounting of the fasteners without mushrooming!
SIZE: #10 x 2-3/4”
Ordinary Bugle Head
Seats Flush
ACQ Treated Lumber Information
31
TRIANGLE FASTENER CORPORATION

ITW BUILDEXB
DEC-KING WOOD DECK FASTENERS
DEC-KING
EXTERIOR
WOOD SCREWS
SELECTOR GUIDE
Head
Part
Description Style Number Applications
6 x1 1/4'' #2 Phillips Bugle 2176500 1'' x 4'' or 1'' x 6'' Base Trim; Lattice
6 x 1 5/8'' #2 Phillips Bugle 2136500 1'' x 4'' or 1' x 6'' Base Trim; Ballisters; Lattice
7 x 2'' #2 Phillips Bugle 2138500 5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking;
1'' x 4'' or 1'' x 6'' Base Trim; Ballisters; Lattice
8 x 2 1/2'' #2 Phillips Bugle 2140500 5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking
2'' x 4'' or 2'' x 6''
Decking
2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim
8 x 3'' #2 Phillips Bugle 2141500 2'' x 4'' or 2'' x 6'' Decking
2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim
10 x 3 1/2'' #2 Phillips Bugle 2142500 2'' x 4'' or 2'' x 6'' Decking
2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim
Dec-U-Drive Tool 2132910
*Parts Kit 2131910
* Contains four 0-Rings; Oil; Loctite; 1/8 Short Arm Hex Key, Bit Retainer Nut, #2 Bit,
3/16’ Hex Key; and 3/8” Combination Wrench.
PRODUCT FEATURES
Coated with Climacoat® for maximum resistance to corrosion,
staining and streaking inside the lumber and on the deck.
Outperforms all zinc based platings in treated wood.
Pullout strength is superior over nails.
Eliminates wood splitting, nail pops, hammer marks and bent nails.
Now available in both #2 Phillips and #2 Square Drive.
DEC-U-DRIVE
STAND-UP INSTALLATION TOOL
Seats Dec-King® screws flush with the deck without damaging the wood.
Eliminates angle driving, under-driven or over-driven screws, screw wobble,
camouts and marring of the deck surface.
Increases productivity and improves the quality of work; providing significant
labor and installed cost savings.
Stand-up operation reduces operator fatigue and increases productivity.
Performance Data
Wood Deck Fasteners
PULLOUT VALUES (AVERAGE POUNDS ULTIMATE)
EMBEDMENT 2'' X 4'' STUD GRADE S.Y. PINE
Description 1/2” 3/4” 1” 1-1/4”
CORROSION RESISTANCE
KESTERNICH RESULTS (DIN 50018, 2.0L)
• 25 Cycles - 10% or less red rust
SALT SPRAY RESULTS (ASTM B117)
• 1000 hours - 10% or less red rust
6 x1-1/4'' 182 329 422 –
6 x 1-5/8” 182 329 422 620
7 x 2” 189 318 440 630
8 x 2-1/2” 186 290 502 630
8 x 3” 186 290 502 645
10 x 3-1/2” 241 386 522 721
Note: The values listed are ultimate averages achieved under laboratory conditions. An
appropriate safety factor should be applied in these values to achieve a design value.
(800) 486-1832 www.trianglefastener.com 32

FASTENERS FOR WOOD
FASTENERS DESIGNED FOR THE FURNITURE INDUSTRY
AND MULTIPURPOSE CONSTRUCTION FASTENING.
FLAT RECEX ® LO-ROOT ®
WOOD SCREW
HARDENED STEEL
Diameter Lengths Carton Quantity
5 1/2, 5/8 15M
6 1/2, 5/8, 3/4 15M
1 10M
1 1/4 8M
1 1/2 7M
8 5/8, 3/4 15M
1 10M
1 1/8 8M
1 1/4 7.5M
1 3/8, 1 1/2 5M
1 3/4 4M
2 3.5M
2 1/4 3M
2 1/2 2.5M
2 3/4 2M
3, 3 1/4 1.5M
10 3/4 10M
1 8M
1 1/4 5M
1 1/2 4M
1 3/4 3M
2 2.5M
2 1/4, 2 1/2 2M
3 1.5M
Lubricized (2001)
THE MAXX
SELECTOR GUIDE
FLAT RECEX ® LO-ROOT ®
WOOD SCREW WITH NIBS
SELF-DRILLING, SELF-
COUNTERSINKING
TYPE 17 HARDENED STEEL
SELECTOR GUIDE
Diameter Lengths Carton Quantity
8 1 10M
1 1/8 8M
1 1/4 7.5M
1 3/8 5M
1 1/2 5M
1 3/4 4M
2 3.5M
2 1/4, 2 1/2, 2 3/4 2.5M
3 1.5M
Lube (2001) • Ultra Seal (3401) •
Black Phosphate (6001)
Dacromet (6501) • Minimum Plating
Charge May Apply
PAN RECEX ® LO-ROOT ®
WOOD SCREW,
HARDENED STEEL
Diameter Lengths Carton Quantity
6 3/8, 1/2, 5/8, 3/4 15M
8 5/8 12M
7/8, 1 8M
1 1/8, 1 1/4 6M
2 3M
10 5/8 8M
Lubricized (2001)
FLAT RECEX ® LO-ROOT ®
WOOD SCREW
(SPECIAL #2 DRIVE)
HARDENED STEEL
Diameter Lengths Carton Quantity
6 1/2, 5/8, 3/4 15M
6 1 10M
6 1 1/4 8M
6 1 1/2 7M
6 1 3/4 5M
Lubricized (2001)
SELECTOR GUIDE
ROUND WASHER RECEX ®
LO-ROOT ® WOOD SCREW
HARDENED STEEL
Diameter Lengths Carton Quantity
8 1/2, 5/8 12M
3/4 10M
7/8, 1 8M
1 1/8, 1 1/4 6M
1 3/8,1 1/2 5M
1 3/4 4M
2 3M
2 1/4, 2 1/2 2M
2 3/4, 3 1.5M
10 1/2 10M
5/8, 3/4 8M
1 6M
1 1 /4 5M
1 1/2, 1 3/4 3M
2 2.5M
2 1/2 1.5M
3 1M
Lubricized (2001)
SELECTOR GUIDE
SELECTOR GUIDE
33
TRIANGLE FASTENER CORPORATION

FASTENERS FOR WOOD
PAN ROBERTSON ®
TYPE A
HARDENED STEEL
Diameter Lengths Carton Quantity
6 1/2, 3/4 15M
1 10M
1 1/4 7.5M
1 1/2 6M
8 1/2 15M
5/8 12M
3/4 10M
1 8M
1 1/4 6M
1 1/2 5M
1 3/4 4M
2 3M
10 3/4 8M
1 6M
1 1/4 5M
1 1/2 3M
1 3/4 3M
2 2.5M
12 1 4M
1 1/4 3M
1 1/2 2.5M
Lubricized (2001)
SELECTOR GUIDE
PAN ROBERTSON ®
(SPECIAL #2 DRIVE)
TYPE 17 (WITH 5/8” THREAD)
FACE FRAME SCREWS
Diameter Lengths Carton Quantity
6 1 1/4 7.5M
1 1/2 6M
Lubricized (2001)
SELECTOR GUIDE
TRUSS RECEX ® LO-ROOT ®
WOOD SCREW
(SPECIAL#2 DRIVE)
TYPE 17 HARDENED
STEEL
SELECTOR GUIDE
Diameter Lengths Carton Quantity
6 3/8, 1/2, 5/8, 3/4 15M
FLAT ROBERTSON ® LO-ROOT ®
WOOD SCREW
(“THE ORIGINAL”)
HARDENED STEEL
Lubricized (2001)
SELECTOR GUIDE
Diameter Lengths Carton Quantity
8 3/4 15M
1 10M
1 1/4 7.5M
1 1/2 5M
1 3/4 4M
2 3.5M
2 1/4 3M
2 1/2 2.5M
3 1.5M
10 1 1/4 5M
1 1/2 4M
1 3/4 3M
2 2.5M
2 1/2 2M
3 1.5M
Lubricized (2001)
ROUND WASHER RECEX ®
WITH EXTRA LARGE WASHER
(.420-.440 HEAD DIAMETER)
FOR DRAWER FRONTS
Diameter Lengths Carton Quantity
8 1 1/8, 1 1/4 5M
Lubricized (2001)
SELECTOR GUIDE
(800) 486-1832 www.trianglefastener.com 34

FASTENERS FOR WOOD
SIZES
WOOD SCREW FLAT HEAD PHILLIPS
Available in Carbon and Stainless Steel
Diameter Lengths
#2 1/4, 3/8, 1/2, 5/8, 3/4
#3 1/4, 3/8, 1/2, 5/8, 3/4
#4 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2
#5 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2
#6 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2
#7 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2
#8 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2, 3, 3 1/2, 4
#9 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2, 3,
#10 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2, 3, 3 1/2, 4
#12 1/2, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/4, 2 1/2, 3, 3 1/2, 4
SIZES
TAPPING SCREW PAN HEAD PHILLIPS
Available in Carbon and Stainless Steel
Diameter Lengths
#4 1/4, 3/8, 1/2, 5/8, 3/4, 1
#6 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 2
#7 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2
#8 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#10 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#12 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#14 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
SIZES
TAPPING SCREW
INDENTED HEX WASHER HEAD
SLOTTED
Available in Carbon and Stainless Steel
Diameter Lengths
#4 1/4, 3/8, 1/2, 5/8, 3/4
#6 1/4, 3/8, 1/2, 5/8, 3/4, 1, 1 1/4, 1 1/2
#7 1/2, 3/4, 1
#8 1/4, 3/8, 1/2, 5/8, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#10 3/8, 1/2, 5/8, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#12 1/2, 5/8, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
#14 1/2, 5/8, 3/4, 7/8, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3
35
TRIANGLE FASTENER CORPORATION

STUDS / TOGGLES / LAG SHIELDS
HANGER STUD
Gimlet point for wood applications
SIZES - STEEL/ZINC
Diameter Lengths
8-32 1”
10-24 1 1/2”, 2, 2 1/2”, 3”
1/4 - 20 1 1/2”, 2”, 2-1/2”, 3”, 3-1/2”
5/16 - 18 2-1/2”, 3”
3/8 - 16 2-1/2”, 3”, 3-1/2”, 4”
SIZES - STEEL/PLAIN
Diameter
Lengths
10 - 24 1-1/2”, 2”, 2-1/2”, 3”
1/4 - 20 2”, 2-1/2”, 3”, 3-1/2”
5/16 - 18 2-1/2”, 3”
3/8 - 16 2-1/2”, 3”, 3-1/2”
SIZES
TOGGLE BOLT ROUND
HEAD SLOTTED
Diameter Lengths
1/8-32 2, 3, 4
3/16-24 2, 3, 4, 5, 6
1/4-20 2, 3, 4, 5, 6
5/16-18 3, 4, 6
3/8-16 4, 6
LAG SHIELD SCREW
SIZES
Diameter Lengths
1/4 (S) 1, (L) 1/2
5/16 (S) 1 1/4, (L) 1 3/4
3/8 (S) 1 3/4, (L) 2 1/2
1/2 (S) 2, (L) 3
5/8 (S) 2, (L) 3 1/2
3/4 (S) 2, (L) 3 1/2
(800) 486-1832 www.trianglefastener.com
36

QUICK DRIVE AUTO FEED SCREW SYSTEM
QUIK DRIVE
AUTO-FEED SCREW SYSTEM
Delivers the superior holding power of screws and more speed than you
ever dreamed possible.
QDPRO200G2
Auto-feed unit , drives screws from 1" to 2" in length, from rigid
collated strips.
QDPRO300SG2
Auto-feed unit , drives screws from 1-1/4" to 3" in length,
from rigid collated strips.
Installation Kit
DRYWALL TO WOOD OR STEEL
Eliminate nail pops, wasted fasteners, wasted motion and
screws under the fingernail. The precise calibrated depth
control provides consistent countersink while the narrow
profile allows driving in corners and hard to reach spots.
WOOD TO WOOD OR PLASTIC TO WOOD
In deck, fence or dock construction, splitting and predrilling are
eliminated with Quik Drive deck screws. Plus, the superior
holding power of screws ensures that nail pops, warping and
twisting are a thing of the past. What goes down stays down.
37
TRIANGLE FASTENER CORPORATION

DRYWALL DRYWALL DRYWALL WOOD WOOD SUB FLOOR WOOD
COARSE FINE SELF-DRILLER COATED COARSE SELF-DRILLER EXTENDER
SCREWS AVAILABLE FOR USE WITH QUIK DRIVE TOOLS
• Our screws are proudly collated in the USA to ensure the highest quality.
• Other screws are available.
• 31 screws per strip
Head Type Dia. Thread Point Finish Application 1-1/4 1-1/2 1-5/8 1-3/4 2 2-1/2 3
Bugle head #6 Coarse Sharp Black Drywall-to-Wood • •
Phillips Phosphate Wood-to-Wood Manufacturing
Drive #6 Fine Sharp Black Drywall-to-Wood • • •
Phosphate Drywall-to-Light Steel
(20-25 gauge)
#6 Fine #2 drill Clear Zinc Drywall-to-Heavy Steel • •
(12-20 gauge)
Flathead #8 Coarse Sharp Yellow Wood-to-Wood • • • • •
Square Zinc Subfloor
Drive #8 Coarse Sharp Lubricized Wood-to-Wood •
Subfloors Cabinets
#8 Coarse Sharp AMG Outdoor Wood-to-Wood •** • •
Rustbuster Decks Docks Fencing etc.
#8 Coarse #2 Drill Clear Zinc Wood lo Steel (12-18 Ga.) •**
*ICBO Approved #5053 ** PPSD2” actually measures 1-15/16
(800) 486-1832 www.trianglefastener.com
38

MARSON ®
RIVETS
KALIDA-KOTE
IN-HOUSE PAINTING
AVAILABLE FOR
CUSTOM COLOR
MATCHING, FAST!
Aged Copper
Almond
Ash Gray
Aztec Gold
Banner Red
Bone White
Burnish Slate
Cape Clue
Charcoal Gray
Cherokee Blue
Classic Green
Cocoa Brown
Colonial Red
Colony Green
Copper Penny
Cordovan
Country Red
Dark Bronze
Desert Sand
Emerald Green
Fern Green
Hartford Green
Hawaiian Blue
Light Stone
39
IN-STOCK COLORS
Mansard Brown
Matte Black
Medium Bronze
Musket Gray
Pacific Blue
Polar White
Red Clay
Roman Bronze
Royal Blue
Rustic Red
Sage
Sahara Tan
Sierra Tan
Seaport
Slate Blue
Slate Gray
Snow White
Snowdrift White
Stone White
Teal Green
Terra Cotta
Winter Blue
H E L Typical Ultimate
D Drill No. & Head Head Rivet Length Strength (Lbs.)
Buttonhead Rivet Dia. Hole Size Dia. Nom. Height Max. Max. Grip Range (newtons)
Material Inch (mm) (mm) Inch (mm) Inch (mm) Inch (mm) Inch (mm) Shear Tensile
Plated-Steel Rivet .212 (5.4) .032-.062 (0.8-1.6)
Steel Mandrel .275 (7.0) .063-.125 (1.7-3.2)
Open End .337 (8.6) .126-.187 (3.3-4.8)
1/8” (.125) #30 (.129-.133) .250 .040 .400 (10.2) .188-.250 (4.9-6.4) 280 410
3.2 3.3 (3.28-3.38) 6.35 1.02 .462 (11.7) .251-.312 (6.5-7.9) 1240 1820
.525 (13.4) .313-.375 (8.0-9.5)
.650 (16.5) .376-.500 (9.6-12.7)
.775 (19.7) .501-.625 12.8-15.9
.325 (8.3) .062-.125 (1.6-3.2)
.450 (11.5) .126-.250 (3.3-6.4)
.575 (14.6) .251-.375 (6.5-9.5)
3/16” (.187) #11 (.192-.196) .375 .055 .700 (17.8) .376-.500 (9.6-12.7) 600 870
4.8 4.9 (4.88-4.98) 9.53 9.53 .825 (21.0) .501-.625 (12.8-15.9) 2665 3870
.950 (24.2) .626-.750 (16.0-19.1)
1.075 (27.3) .751-.875 (19.1-22.2)
1.200 (30.5) .876-1.000 (22.3-25.4)
5056 .212 (5.4) .032-.062 (0.8-1.6)
Aluminum Rivet .275 (7.0) .063-.125 (1.7-3.2)
Steel Mandrel .337 (8.6) .126-.187 (3.3-4.8)
Open End 1/8” (.125) #30 (.129-.133) .250 .040 .400 (10.2) .188-.250 (4.9-6.4) 180 270
3.2 3.3 (3.28-3.38) 6.35 1.02 .462 (11.7) .251-.312 (6.5-7.9) 800 1200
.525 (13.4) .313-.375 (8.0-9.5)
.650 (16.5) .376-.500 (9.6-12.7)
.775 (19.7) .501-.625 (12.8-15.9)
.325 (8.3) .062-.125 (1.6-3.2)
.450 (11.5) .126-.250 (3.3-6.4)
3/16” (.187) #11 (.192-.196) .375 .055 .575 (14.6) .251-.375 (3.5-9.5) 440 700
4.8 4.9 (4.88-4.98) 9.53 1.40 .700 (17.8) .376-.500 (9.6-12.7) 1950 3110
.825 (21.0) .501-.625 (12.8-15.9)
.950 (24.2) .626-.750 (16.0-19.1)
1.200 (30.5) .751-1.00 (19.1-25.4)
Aluminum Rivet .212 (5.4) .032-.062 (0.8-1.6)
Aluminum Mandrel .275 (7.0) .063-.125 (1.7-3.2)
Open End .337 (8.6) .126-.187 (3.3-4.8)
1/8” (.125) #30 (.129-.133) .250 .040 .400 (10.2) .188-.250 (4.9-6.4) 150 180
3.2 3.3 (3.28-3.38) 6.35 1.02 .462 (11.7) .251-.312 (6.5-7.9) 660 800
.525 (13.4) .313-.375 (8.0-9.5)
.650 (16.5) .376-.500 (9.6-12.7)
.775 (19.7) .501-.625 (12.8-15.9)
.325 (8.3) .062-.125 (1.6-3.2)
.450 (11.5) .126-.250 (3.3-6.4)
.575 (14.6) .251-.375 (6.5-9.5)
3/16” (.187) #11 (.192-.196) .375 .055 .700 (17.8) .376-.500 (9.6-12.7) 280 430
4.8 4.9 (4.88-4.98 9.53 1.40 .825 (21.0) .501-.625 (12.8-15.9) 1240 1910
.950 (24.2) .626-.750 (16.0-19.1)
1.075 (27.3) .751-.875 (19.1-22.2)
1.200 (30.5) .751-1.00 (19.2-25.4)
1.450 (36.8) 1.125-1.250 (28.6-31.8)
Stainless Rivet .212 (5.4) .032-.062 (0.8-1.6)
Steel Mandrel .275 (7.0) .063-.125 (1.7-3.2)
IFI Grade 50 1/8” (.125) #30 (.129-.133) .250 .040 .337 (8.6) .126-.187 (3.3-4.8) 520 600
Open End 3.2 3.3 (3.28-3.38) 6.35 1.02 .400 (10.2) .188-.250 (4.9-6.4) 2310 2660
.462 (11.7) .251-.312 (6.5-7.9)
.525 (13.4) .313-.375 (8.0-9.5)
.650 (16.5) .376-.500 (9.6-12.7)
.325 (8.3) .062-.125 (1.6-3.2)
.450 (11.5) .126-.250 (3.3-6.4)
.575 (14.6) .251-.375 (6.5-9.5)
3/16” (.187) #11 (.192-.196) .375 .055 .700 (17.8) .376-.500 (9.6-12.7) 1150 1300
4.8 4.9 (4.88-4.98) 9.53 1.40 .825 (21.0) .501-.625 (12.8-15.9) 5110 5780
.950 (24.2) .626-.750 (16.0-19.1)
1.120 (30.5) .751-1.000 (19.2-25.4)
#110 Copper Rivet
Brass Mandrel 1/8” (.125) #30 (.129-.133) .125 .040 .275 (7.0) .063-.125 (1.7-3.2) 215 300
IFI Grade 20 3.2 3.3 (3.28-3.38) 6.35 1.02 .400 (10.2) .188-.2505 (4.9-6.4) 950 1330
Open End
#5056 Aluminum Rivet .296 (7.52) .032-.062 (0.8-1.6)
Steel Mandrel .355 (9.02) .063-.125 (1.7-3.2)
1/8” (.125) #30 .236 .035 .414 (10.52) .126-.187 (3.3-4.8) 240 280
Closed End 3.2 (.129-.133) .473 (11.10) .188-.250 (4.9-6.4) 1060 1240
.532 (13.51) .251-.312 (6.5-7.9)
.591 (15.06) .313-.375 (8.0-9.5)
TRIANGLE FASTENER CORPORATION

MARSON ®
RIVETS
BIG DADDY®/39031
HP-2®/39000
The HP-2 is the largest selling hand rivet tool in the industry. Known
and trusted for durability, quality and performance, the HP-2 is often
copied but never equaled. Its square shoulder fulcrum pin of coldformed
heat-treated steel prevents pin rotation that can elongate the
engaging holes and cause premature tool failure in imitation tools.
Other quality features include: precision die-case, high-strength
aluminum alloy body; drop-forged carbon steel upper handle; and
thick, cushion-molded vinyl grips for comfort. The HP-2 sets up to
3¼16" steel rivets and comes with four mounted nosepieces (3¼32",
1¼8", 5¼32" and 3¼16") and a service wrench. Refer to the Riveter
Capacity Chart on page 24 for specific capabilities.
Weight: 1.2lbs.; 1/carton.
The Big Daddy is Marson’s most versatile and powerful hand riveter,
taking the hard work out of setting large diameter blind rivets. Its
extra-long handles provide excellent leverage and permit working a
foot beyond natural reach. Other features include a patented bearing
design, self-adjusting two-piece jaws and single-unit body construction
with a steel insert to provide stronger threads for the nosepieces
included. In addition, the Big Daddy features a double-gear reduction
system which easily sets from 1¼8" to 1¼4" diameter Klik-Fast rivets in
all alloys, including 1¼4" Klik-Split® and 3¼16" and 1¼4" Klik-Lock®*
rivets. And a one-piece collet case eliminates the need to adjust the
tool when changing rivet diameters. The Big Daddy comes with 5¼32",
3¼16" and 1¼4" nosepieces which are stored in the body.
Weight: 33¼4 lbs.; 1/case.
BIG DADDY/39010
This is the same tool as 39031, but comes with 3¼16", 1¼4" and special 1¼4"
Klik-Split rivet nosepieces. Weight: 33¼4 lbs.; 1/case.
BIG DADDY
EXTENDED
NOSEPIECE
KIT/39009
BIG DADDY/39035
Just two installed parts extend the reach of 39031 and /or
39010 an additional 21¼2". Weight: 1¼4 lb.; 1/case.
Extended head
This is the same tool as 39010, but comes with 39009 attached, extending the
tool’s reach by an additional 21¼2". Weight: 4 lbs.; 1/case.
NOSE PIECE CHART
Rivet Sizes Monobolt ® Sizes T-Rivet Sizes
Tool 3/32” 1/8” 5/32” 3/16” 1/4” 3/16” 1/4” 3/16” 1/4”
39000 39131 39128 39130 39129 -- -- -- -- --
39040 39131 39128 39130 39129 -- -- -- -- --
39031 -- 96024 96025 96026 96027 96031 96030 96029 96028
* When setting Marson Klik-Lock rivets, no special nosepiece is required.
(800) 486-1832 www.trianglefastener.com 40

FABLOK RIVET
Contact TFC for details
FAB-LOK® FASTENERS
TO MAINTAIN PANEL INTEGRITY IN HIGH-STRESS
ENVIRONMENTS
Vibration, either from inside or outside a building, can make ordinary fasteners loosen and back
out.
Fab-Lok® fasteners combine a slotted aluminum sleeve and fastener to provide the simplicity and
strength of both elements.
Features:
• Hex washer head machine screw assembled to a slotted
aluminum sleeve and EPDM sealing washer.
• Carbon steel or stainless steel screws.
• Installs with power drive equipped with Fab-Lok ® holding sleeve.
Benefits:
• After tightening, clamping tines remain
in place even if the screw is removed
• Greater joint integrity
• Consistent drill times and hole sizes
• Increased construction efficiency
After Installation
WEATH-R-SEAL ® WASHERS
Part
Description
Aluminum Bonded
.729" O.D. – .040 Aluminum
Weath-R-Seal ® Washers 1" O.D. – .040" Aluminum
304 Stainless Steel Bonded .729" O.D. 20 gage 304 S/S
Weath-R-Seal ® Washers 1" O.D. 20 gage 304 S/S
FAB-LOK ® FASTENERS
Material Size Penetrating Length Grip Range Wt./M
Carbon Steel FAS 10-4 1.373" .062"–.250" 23
FAS 10-8 1.612" .250"–.500" 24
FAS 10-12 1.807" .500"–.750" 28
H-3 (300 Series) FAC 10-4 1.373" .062"–.250" 23
Stainless Steel FAC 10-8 1.612" .250"–.500" 24
FAC 10-12 1.807" .500"–.750" 28
FAB-LOK PERFORMANCE FEATURES
Pull-out tests were performed on a Model L Dillon Dynamometer. FAB-LOK fasteners were installed in single sheet
and two sheets of metal and pulled over the tines of the FAb-LOK to determine holding values.
Information provided herein is based upon tests believed to be reliable. Inasmuch as Fabco Fastening Systems has no control over the
exact manner in which others may use this information, it does not guarantee the results to be obtained. Nor does the Company make any
express or implied warranty of merchantability, or fitness for a particular purpose concerning the effects or results of such use.
SINGLE SHEAR STRENGTH
Fab-Lok Type FAC FAS
Average Shear 1885 lbs 2400 lbs.
CLAMPING FORCE
Fab-Lok Type FAS
Maximum
900 lbs
Residual
860 lbs.
HYDROSTATIC TEST
Fab-Lok Type H20 Pressure Length of test Result
FAC-10-4 100 psi 5 days No Leaks
TYPE FAC - SINGLE SHEET THICKNESS
Sheet Sheet * Failure Type Of
Material Thickness lbs. Failure
24 ga. 833 Sheet Split
20 ga. 858 Sheet Split
Steel 18 ga. 1050 Sheet Split
16 ga. 1293 Sheet SPlit
14 ga. 1400 Fastener Broke
COMPARISON - FAB-LOK & SHEET METAL SCREW
Sheet FAB-LOK #14 Sheet
Material FAS-10-4 Metal Screw
Strip test in .032” Aluminum 75 inch-lbs.* 65inch-lbs.*
Strip test in 26 ga. Steel 75 inch-lbs.* 45inch-lbs.*
Strip test in 24 ga. Steel 75 inch-lbs.* 55inch-lbs.*
* FAB-LOK, even when stripped, retains a residual clamp-up and
remains effective. Sheet metal screws are loose when stripped.
TYPE FAC - DOUBLE SHEET THICKNESS
Sheet Sheet * Failure Type Of
Material Thickness lbs. Failure
Steel 26 ga. 1160 Sheet Split
20 ga. 1345 Sheet Bent,
Fastener Tines
Broke
Aluminum .032” 915 Sheet Split
FATIGUE TESTS
Two thicknesses 0f 26 gage metal fastened with FAB-LOK and tested on
5000 lb. capacity machine at 1500 cycles per minute, sustained 1,776,500
cycles when failure of sheets occurred. Fastener did not fail.
FAB-LOK fastening 1/8” aluminum plate to 3/16” steel of a railroad freight
car, held without failure when the car was subjected to jarring vibration by
a Hewitt-Robins Car Shaker at 900 cycles per minute for ten minutes.
41
TRIANGLE FASTENER CORPORATION

EXPLOSION RELEASE / GROMMET FASTENERS
EXPLOSION VENTING FASTENERS Limit damage from industrial or agricultural explosions.
A series of collapsible washers on stainless steel fasteners designed to minimize injury and destruction of
property from explosions caused by agricultural or industrial operations.
• .729" O.D. washer with special aluminum
alloy bonded with EPDM or neoprene
sealant
• Stainless steel machine screws
• Washers designed to collapse under force
of explosion, allowing panel to separate
and vent shock waves
• Maintains standard building integrity
• Minimizes destruction from explosion by
quickly dissipating explosive forces
• May be used with any sheet or panel, with
or without insulation, in field-assembled or
shop-assembled walls
Panel
Centering
device
Panel
separates
from
framing
member
Explosive
force
Washer Color Release Value
Designation Code per Fastener
EXA-74 Green 70#
EXA-76 Blue 110#
EXA-79 Tan 175#
EXA-84 Light Green 435#
EXA-19 Light Blue 885#
Framing
member
Note: These are the average release pressures for each washer.
#14 Fabco ® Vent-All
Fastening System featuring
aluminum pressure-release
washer
Fabco ®
aluminum
pressurerelease
washer
deforms
Fabco ® application specialists will work with
your designers to specify the optimal
number, placement and type of Vent-All
fasteners to be used on your project.
Normal Installed Condition
Interior Explosion Release Conditions
It is suggested that all sheets or panels be
provided with restraint cables, about three feet
long, anchored to the structure to prevent sheets
from becoming flying projectiles.
Contact TFC for information
GROMMET SEAL
Grommet Seal Fasteners are
compression fasteners used in Side-lap
applications which utilize fiberglass,
plastic or composite sheeting.
Grommet Seals consist of:
• A Hex Head machine screw
• A bonded sealing washer
• An elongated rubber sleeve with an
internal molded brass nut.
SPECIFICATIONS
Grommet Size: 1/4” X 1” 3/8” X 1”* 3/8” X 1-1/4”*
Body Length: .948 .812 1.000
Nut Insert: 6-32 10-32 10-32
Durometer (sleeve): 70 60 60
Ultimate Tensile: 50 Lbs. 80 Lbs. 80 Lbs.
* Also Available in 316 Stainless Steel.
MACHINE SCREW
Machine Screw Size: 6-32” X 1” 10-32 X 1”* 10-32 X 1-1/4”*
Hex Size: 1/4” 5/16” 5/16”
Material: 302 HQ 302 HQ 302 HQ
Bonded Washer: 304 SS/EPDM 304 SS/EPDM 304 SS/EPDM
Sleeve: EPDM EPDM EPDM
Nut Insert: Brass Brass Brass
Recommended
Hole Size: .250 .375 .375
Grip Range: .375-.607 .312-.450 .312-.545
INSTALLATION
The grommet is installed by placing it into a pre-drilled 1/4” or 3/8”
hole and tightened using a screwgun with a standard 1/4” or 5/16”
socket. The machine screw engages the nut insert, forcing the
sleeve to expand against the inner wall of the materials.
Grommets become an excellent sealant against air,
moisture and vibration.
After Installation
(800) 486-1832 www.trianglefastener.com 42

BULB-TITE
RIVETS
BULB-TITE RIvets
More than forty years ago the first Bulb-tite was developed to solve application requirements
in the Pre-Engineered Metal Building industry. Since that time the Bulb-Tite product line has
been expanded to meet application requirements in a wide range of industries. The Bulb-tite
rivet body folds into three separate legs forming a large blind-side head. This large bearing
head evenly distributes the Bulb-tite's high clamp force in soft, thin or brittle materials while
providing high pull through resistance. The Bulb-tite's wide grip range enables a single Bulbtite
to work in a greater variation of thickness. Some versions of the Bulb-tite feature a
special flush break mandrel that effectively seals the rivet bore and adds greater shear
strength.
RV6003 & RV6604 - Dome Head
(Protruding Crown)
RV6605 - Large Flange Head
(Protruding Crown)
43
TRIANGLE FASTENER CORPORATION

SECURITY SCREWS
Screw Types
Head Styles
SPANNERS
The spanner requires matching drive bit reducing the
chances of unauthorized removal. Available in 18-8
stainless steel in a wide range of sizes and head
styles. Some machine screws available in brass.
Nuts are zinc alloy.
PHILLIPS PIN-HEAD
Traditional Phillips drive with tamper resistant pin
added for security. Easy to drive and remove with
matching tool. (Cannot be removed with Phillips
Screwdriver.) Available in machine and sheet metal
screws with flat or pan head design.
PAN
Features a low profile, large diameter head with a
high-edged crown for increased strength.
FLAT
Installs flush with countersunk materials for clean
appearance.
TRUSS
Low profile offers added security. Large diameter
head for increased fastening strength.
ONE-WAY SLOTTED
Popular design installs with standard screwdriver.
Reverse side cammed out to prevent unauthorized
removal. Machine and sheet metal screws
available in round, truss or oval head designs.
Sex bolts also available.
REVERSE THREAD
A reverse thread sheet metal screw that installs
counterclockwise, thus, tightens if removal is
attempted. Available with a low profile truss head.
SOCKET PIN-HEAD
Engineered for a high degree of tamper resistance
offering positive engaging, high torque transmission
while resisting cam out and tool wear. Available in
button and flat head design or set screws (special
order). Matching drive bit required for installation and
removal.
TP3 TRIANGULAR
New trilobular drive offers a high degree of security
requiring matching tool bit.
TORX ® PIN-HEAD
Maximum torque transfer and positive tool engagement
means easier drive installation with less pressure and
slippage. Torx® Pin Head offers a high degree of
security and requires matching drive bit. Available in
button & flat head machine screws and button, flat and
pan head design sheet metal screws.
ROUND
One way screws only. Features a high crown with a
deep recess and a smaller diameter head than truss
or pan head.
OVAL
Used where countersink installation is desired.
Rounded head offers deep recess and is visible just
above the surface.
BUTTON
Also used for general purposes with a lower crown
and shallower recess than round head design.
Thread and Point Styles
SHEET METAL A OR B
Thread forming screw with locating point.
MACHINE SCREW
Machine screw standard thread, straight sheared
point.
SELF-DRILLING
Type AB thread with a 410 heat treated stainless
steel, #2 self drilling point.
CONTACT TRIANGLE FASTENER FOR YOUR SPECIFIC SIZE AND TYPE
(800) 486-1832 www.trianglefastener.com 44

NAILS
FRAMING-SINKERS
• 1lb. - 5 lb. - bulk coated
Length
2”, 2-1/2”, 3-1/4”, 3-1/2”
COPPER AND 304
STAINLESS STEEL
ROOFING NAILS
• 1lb. - 5 lb. - bulk Boxes
Gauge
Lengths
12 3/4”,1”, 1-1/4”, 1-1/2”, 2”
11 3/4”,1”, 1-1/4”, 1-1/2”, 2”
10 1”, 1-1/4”, 1-1/2”, 2”, 3”
FINISH NAILS
• 1lb. - 5 lb. - bulk brite finish
Length
1-1/2”, 2”, 2-1/2”
PLASTIC CAP NAILS
• Bulk Boxes
• Fastening roof felt to decks
Leg Length
3/4”, 7/8”, 1”, 1-1/4”, 1-1/2", 1-3/4", 2”, 2-1/2”, 3”
TENSION NAILS
• 1lb. - 5 lb. - bulk boxes
Length
1-1/8”
EG ROOFING NAILS
• 1lb. - 5 lb. - bulk coated
Length
1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3"
DRYWALL NAILS
• 1lb. - 5 lb. - bulk boxes, cupped head
Length
1-3/8", 1-5/8"
BUTTONKAP PLUS
ButtonKap Nailer and Roofing Nailer
• Can be used as a ButtonKap
Nailer AND a Roofing Nailer
• Saves Labor and Time
• Shoots Steel and Plastic Caps
• 3/4” and 1 3/4”
• Fast, Easy Loading
• Uses Coil Roofing Nails
CONCRETE NAILS
• Fluted shank for fast penetration into
“uncured” concrete.
• 3/4” penetration into the concrete
is recommended
• Hot Dipped Galvanized
PACKAGING
We offer 3 sizes to meet your demands
1 pound
5 pound
Length
3/4”, 1”, 1-1/4”, 1-1/2", 1-3/4", 2”, 2-1/4”, 2-1/2”,
3”, 3-1/4”, 4”, 4-1/2”, 5, 5-1/2”, 6”, 7”, 8”
Bulk Pak
45
TRIANGLE FASTENER CORPORATION

COLLATED PNEUMATIC NAILS
Available for Bostitch - Senco - Paslode - Hitachi - Porter Cable
COIL NAILS
FRAMING
Smooth or RIng Shank Diameters
.099”, .120”, .131”
ROOFING
Length
7/8”, 1”, 1-1/4”, 1-1/2”, 1-3/4”
Length
2”, 2-3/8”, 3”, 3-1/4”, 3-1/2”
Diameter
.120”
STRIP NAILS
FRAMING (STRIP)
FINISH
Diameters
.113”, .120”, .131”
Length
3/4”, 1”, 1-1/4”, 1-1/2”, 2”
Length
2”, 2-3/8”, 3”, 3-1/4”, 3-1/2”
STRIP CROWN
STAPLES
Available Finish: Brite -
Electro Galvanized - Hot Dip
16 gauge
WIDE CROWN (15/16”)
Length
5/8”, 3/4”, 7/8”, 1”, 1-1/8”, 1-1/4”, 1-3/8”, 1-1/2”
16 gauge
MEDIUM CROWN (1/2”)
Length
3/4”, 1”, 1-1/4”, 1-3/8”, 1-1/2”, 1-3/4”, 2”
Senco, Paslode, Porter Cable, hitachi, and
Bostitch are registered trademarks.
18 gauge
NARROW CROWN (3/16”)
Length
1/2”, 5/8”, 3/4”, 7/8”, 1”, 1-1/8”, 1-1/4”
(800) 486-1832 www.trianglefastener.com 46

NAILERS
- 3 1/2”
- 3 1/4”
- 3 1/4”
- 3”
- 3”
POWERMASTER PLUS
NAILER
Fastener type
D-head strip nails
Shank diameters available .113,.120, .131
Length 2” - 3 1/2”
Finishes
Brite, galvanized and
TLN
(Treated Lumber Nail)
Collation media
Paper tape collated
Collation angle
30 degree
- 2 7/8”
- 2 3/4”
- 2 3/8”
- 2”
- 2 3/4”
- 2 3/8”
- 2 1/4”
- 2”
Model:
F-350S
Part number: 501000
Weight:
7.9 lbs.
Height:
13 in.
Magazine type:
30 degree stick
(nail strip)
Cycle rate:
10 nails/second
Nail capacity:
74-84 nails (2 strips)
Air req./90 p.s.i. (6.3 bar): .082/cycle
Op. pres. p.s.i. (bar): 80-120 (5.5-8.3)
Ring shank
Smooth
CORDLESS UTILITY
FRAMING NAILER
- 3 1/4”
- 3”
- 3 1/4”
- 3”
- 2 1/2”
- 2 3/8”
- 2 1/4”
- 2”
- 2 1/2”
- 2 3/8”
- 2 1/4”
- 2”
Model
IMCT
Part number 900420
Weight
6.9 lbs.
Height
14 1/2 in.
Cycle rate
2-3 nails/second
Nail capacity 44
Fuel cell life
1,200 nails (approx.)
Battery cell life per charge 4,000 nails (approx.)
• Ring Shank*
Not recommended for use at altitude above 5000 feet, or in
temperatures below 20 0 F (7 0 C).
• Brite, galvanized, mechanical galvanized
and TLN (Treated Lumber Nail).
• Smooth
• Brite, galvanized and TLN
(Treated Lumber Nail).
• Shank Diameters available: .113, .120, .131
* The Impulse® cordless utility framing nailer is not
recommended for use with 3” and 3 1/4” ring shank
nails in pressure-treated lumber.
Ring shank
Smooth
47
TRIANGLE FASTENER CORPORATION

NAILERS
16 GAUGE FINISH NAILER
• Powerful - drives 3/4” to 2 1/2”
16 gauge finish nails into hard
woods.
• Comes with rugged carrying
case - tough plastic case with
safety glasses, convenient
storage for finish nails and
operating/safety instructions.
- 2 1/2”
- 2 1/4”
- 2”
- 1 3/4”
- 1 1/2”
- 1 1/2”
- 1”
Model
T250-F16
Part number 500970
Weight
4.2 lbs.
Height
10 in.
Cycle rate
12 nails/second
Nail range 3/4” to 2-1/2”
Magazine type
Straight
Nail capacity
100 (2 strips)
Air req./80 p.s.i.
.040/cycle
Operating p.s.i. (bar) 80-120
16 gauge
Galvanized
CORDLESS FINISH NAILER
16 Gauge smooth galvanized
Not recommended for use at
altitude above 5,000 feet, or in
temperatures below 20 0 F (7 0 C).
- 2 1/2”
- 2 1/4”
- 2”
- 1 3/4”
- 1 1/2”
- 1 1/4”
- 1”
- 3/4”
Model
IM250 II
Part number 900400
Weight
5.5 lbs.
Height
12 1/2 in.
Cycle rate
2-3 nails/second
Nail capacity
100 (2 Strips)
Fuel cell life
2,400 nails (approx.)
Battery cell life per charge 4,000 nails (approx.)
16 gauge
Smooth galvanized
TRIMMASTER ® Cordless
Angled Finish Nailer
16 Gauge smooth galvanized
angled.
Use Blue Metering valve at
altitude above 4,000 feet, or in
temperatures below 20 0 F (-7 0 C).
- 2 1/2”
- 2”
- 1 3/4”
- 1 1/2”
- 1 1/4”
Model
IM250A
Part Number 900600
Weight
4.9 lbs. with battery
Height
11 1/2 in.
Cycle rate
2-3 nails/second
Nail capacity
100 (2 Strips)
Fuel cell life
1,200 nails (approx.)
Battery cell life per charge 4,000 nails (approx.)
16 gauge
Smooth galvanized
angled
(800) 486-1832 www.trianglefastener.com 48

STAPLERS
SNS40
Compact and lightweight, a great
performer in most 16 gage staple jobs.
• H: 9 7¼8” L: 14” W: 4.1 lbs
• Lightweight - only 4.1 lbs.
• Oil-less design; no need to lubricate.
• Fast multi-directional stitching.
7¼16” crown. 16 gauge staples.
1” - 2” lengths. Capacity 160+.
*2” staples for soft wood applications only.
SLS20
Powerful finish and trim staplers
designed for easy handling and
virtually trouble-free maintenance.
• H: 8 1¼2” L: 12” W: 2.5 lbs
• Lightweight (2.5 lbs) and easy to handle with
ergonomic design and soft grip.
• Adjustable depth-of-drive control allows for
precise countersinking.
• Designed with only one movable seal for
virtually trouble-free operation.
Available crown widths 3¼16”, 1¼4”, 3¼8” .
18 gauge staples. 3¼8" - 1 1¼2" lengths.
Capacity 168.
ARROW
STAPLE GUN TACKER
MODEL T50
• Easy Squeeze Mechanism
• 2 Year Limited Home Use Warranty
• All Purpose
• Heavy Duty
• Shoot a Staple Wherever You Would Drive a Nail
STAPLES
• Arrow brand high quality
• Fits Arrow, Stanley, Craftsman,
B&D Hand Staplers
Leg Length
5/16”, 3/8”, 1/2”, 9/16”
49
TRIANGLE FASTENER CORPORATION

SENTRY PLUS FIVE ROOFING SCREWS
FASTENERS FOR FLAT ROOFING
The most comprehensive fastener line for the roofing industry!
FM approved and available for all roofing systems.
#10, #12, #14, #15 DIAMETERS
TRUSS HEAD WITH PHILLIPS DRIVE #12 DIAMETER HEX HEAD DRIVE
• Provided with #3 phillips truss
head for driving stability.
• Epoxy coated for optimal corrosion protection
exceeds FM 4470 standard!
• Available in stainless steel for reroof applications!
• Provided with 1/4” hex washer head.
• Epoxy coated for optimal corrosion
protection exceeds FM 4470 standard!
• Fasteners are packaged in KWIK-PAK plastic buckets!
• Compatible with warranty roof systems
• Compatible with warranty roof systems
SENTRY PLUS FIVE PRE-ASSEMBLED
Complete line of #14 diameter fasteners assembled
with Galvalume, plastic, or nylon insulation plates!
PLATES
A full line of plates for all your requirements!
SAVE UP TO 30% ON
INSTALLATION TIME!
Pick-Up Tool
High performance
pick-up tool for easy
installation of
preassembled
fasteners and plates
Square, Hex, Round...Steel or Plastic...We have
what you need!
3” x 3” Square Recessed Galvalume Metal
3” x 3” Square Flat Bottom Galvalume Metal
3” Across Flats Hex Galvalume Metal
3” Across Flats Hex Plastic
2” Round Galvalume Metal (Standard)
2” Round Galvalume Metal (Recessed)
2” Round Galvalume Metal with Plastic Locking Feature
2” Round Galvalume Metal with Plastic Locking Feature
and Protective Outer Ring
3” Round Galvalume Metal (Standard)
3” Round Galvalume Metal (Recessed)
3” Round Plastic
3” Round Plastic with Locking Feature
(800) 486-1832 www.trianglefastener.com 50

SENTRY PLUS FIVE ROOFING SCREWS
DIAMETERS AND LENGTHS
Metal Deck: Fastener must penetrate the deck by a minimum of 3/4”.
Concrete and Wood: Fastener embedment of 1” or a minimum of 1” penetration through wood decking.
All sizes to meet your requirements!
CHOOSE FROM THE LARGEST SELECTION OF
ROOFING FASTENERS IN THE INDUSTRY!
#10
#12
#12-24
#14
#14 SS
#15
Sentry Plus Five fasteners are FM
approved and fastener coatings
meet FM specification #4470.
Contact your TFC product
professional for approval details.
Fastener
Diameters
Length #10-11 #12-15 # 12-24 # 14-13 # 14-13SS #15-13
1-1/4”
1-3/8”
1-1/2”
1-5/8”
2”
2-1/4”
2-1/2”
2-3/4”
2-7/8”
3”
3-1/4”
3-1/2”
3-3/4”
4”
4-3/8”
4-1/2”
4-3/4”
5”
5-1/2”
5-3/4”
6”
6-1/2”
6-3/4”
7”
7-1/2”
7-3/4”
8”
9”
10”
11”
12”
14”
16”
18”
20”
22”
24”
26”
Sizes Available
WE OFFER FASTENERS COMPATIBLE WITH THE FOLLOWING ROOF SYSTEMS
• Carlisle • Firestone • GAF • Genflex • Johns-Manville •
• Sarnafil • Soprema • Tamko • Versico •
51
TRIANGLE FASTENER CORPORATION

TECHNICAL DATA SHEET
Technical Information
PULLOUT VALUES IN STEEL
(AVERAGE ULTIMATE IN POUNDS)
PULLOUT VALUES IN WOOD
(AVERAGE ULTIMATE IN POUNDS)
FASTENER DIAMETERS
Material
Thickness #10-11 #12-15 #12-24 #14-13 #15-13
24ga 364 lbs. 335 lbs. 347 lbs.
22ga 410 lbs. 452 lbs. 472 lbs. 538 lbs.
20ga 560 lbs. 456 lbs. 656 lbs. 646 lbs.
18ga 558 lbs. 375 lbs. 830 lbs. 916 lbs.
16ga
500 lbs.
14ga
978 lbs.
12ga
1200 lbs.
1/8” 2000 lbs.
1/4” 3844 lbs.
FASTENER DIAMETERS
MATERIAL #10-11 #12-15 #14-13 #15-13
1/2” Ply 348 lbs. 339 lbs. 347 lbs. 455 lbs.
5/8” Ply 516 lbs.
3/4” Ply 585 lbs. 588 lbs. 596 lbs. 661 lbs.
7/16” OSB 218 lbs. 218 lbs. 260 lbs.
19/32” OSB 320 lbs. 310 lbs. 323 lbs.
23/32” OSB 326 lbs. 327 lbs. 444 lbs.
2x Pine (1”) 539 lbs. 742 lbs. 913 lbs.
2x Pine (full) 1161 lbs. 1298 lbs. 1567 lbs.
Full penetration except where noted
Grade E Decking (30KSI Minimum Steel)
PULLOUT VALUES IN CONCRETE
(AVERAGE ULTIMATE IN POUNDS)
STRENGTHS OF FASTENERS
Fastener Torsional Tensile Shear
Diameter (inch lbs,) (Pounds) (Pounds)
#6-20 (.125”) 25 1125 750
#8-18 (.164”) 42 1575 1000
#10-16 (.190”) 61 2100 1400
#12-13 SP5 (.222) 76 2410 1815
#12-14 (.216”) 92 2778 2000
#12-24 (.210”) 100 3188 2100
#14-13 SP5 (238”) 115 3600 2630
1/4-14 (.250”) 150 4275 2600
1/4-20 (.250”) 156 4275 2700
#15-13 SP5 (.263”) 140 4350 3700
SENTRY PLUS
FIVE
ZAMAC SPIKE TAPCON
FASTENER TYPES
Sentry Plus Five Zamac Spike Tapcon
#14-13 #15-13 3/16” 1/4” 1/4” 1/4”
959 lbs. 733 lbs. 500 lbs. 600 lbs. 945 lbs. 718 lbs.
Structural Concrete 3,000 PSI minimum
TOOLING RECOMMENDATIONS
Screw gun RPM
#6, #8, 10, #12 0 - 2,500 RPM
1/4” & Heavy Gauge 0 - 2,000 RPM
18-8 Stainless Steel 0 - 1,000 RPM
Fasteners should be installed perpendicular to
the fastening surface. Depth sensing
nosepiece should be used to
prevent over torquing.
DECIMAL & METRIC CONVERSIONS
Gauge Decimal Metric
Thickness
Equivalent
29 ga .013” .33mm
28 ga .015” .38mm
26 ga .018” .46mm
24 ga .024” .61mm
22 ga .030” .76mm
20 ga .036” .91mm
18 ga .048” 1.22mm
16 ga .060” 1.52mm
14 ga .075” 1.91mm
12 ga .105” 2.67mm
1/8” 125” 3.18mm
10 ga .135” 3.43mm
1/4” .250” 6.35mm
5/16” .312” 7.92mm
3/8” .375” 9.53mm
1/2” .500” 12.7mm
(800) 486-1832 www.trianglefastener.com 52

ITW BUILDEX
ROOFING SCREWS
HEXTRA
An industry first.
Premium performance fastener
for insulation attachment to
steel and wood roof decks.
PRODUCT
SPECIFICATIONS
Diameter: #12
Thread form: Modified buttress
Head style: Hex washer
Drilling capacity: 16-26 gauge metal deck
Coating: SPEX and Climaseal
Installation: ITW Buildex AccuTrac or AccuDrive XL
PLUS installation tools or
standard 1,800-2,500 RPM
screwgun
SELECTOR GUIDE
Part
Number Fastener Insulation Range Insulation Range
(SPEX*) Length (Top Flange) (Top or Bottom Flange)
6001106 1 5/8” 1/2” to 1 1/8”
6002106 2 1/4” 1/2” to 1 3/4”
6003106 2 7/8” 1” to 2 3/8”
6004106 3 1/4” 1/2” to 2 3/4” 1/2” to 1 1/4”
6005106 3 3/4” 1” to 3 1/4” 1” to 1 3/4”
6006106 4 3/8” 5/8” to 3 7/8” 5/8” to 2 3/8”
6007106 5” 1 1/4” to 4 1/2” 1 1/4” to 3”
6008106 6” 3 1/4” to 5 1/2” 3 1/4” to 4”
6009106 7” 3 1/4” to 6 1/2” 3 1/4” to 5”
6010106 8” 4 1/4” to 7 1/2” 4 1/4” to 6”
*Hextra fasteners are also available with premium Climaseal coating.
PULLOUT VALUES
In Metal
Gauge 16 18 20 22 24 26
Lbs. 874 674 502 425 330 235
In Plywood
Thickness 3/8" 1/2" 3/4"
Lbs. 200 326 544
In Wood Plank
Depth 1" 1 1/4" 1 1/2"
Lbs. 784 1084 1292
Ultimate tensile load - 2562 lbs. Ultimate shear load- 1229 lbs.
NOTE: Test results were
obtained under laboratory
controlled conditions.
Appropriate safety factors
should be applied to these
ultimate values.
GearLok, SPEX, Hextra,
Climaseal, AccuTrac,
AccuDrive XL PLUS,
Roofgrip and Building Ideas
That Work are trademarks
of ITW Buildex and Illinois
Tool Works Inc.
53
TRIANGLE FASTENER CORPORATION

ITW BUILDEX
ROOFING SCREWS
#14 ROOFGRIP
Reliable all-purpose fastener
attaches insulation and
single-ply membrane to steel,
wood and structural concrete
roof decks.
PRODUCT
SPECIFICATIONS
Diameter: #14
Thread form: Standard spaced thread
Head Style: #3 Phillips
Drilling capacity: 16-26 gauge metal deck
Coating: Spex
Installation: ITW Buildex
Accudrive XL PLUS
or a standard
1,800-2,500 RPM
screwgun
PRODUCT
SPECIFICATIONS
SELECTOR GUIDE
Steel Insulation Range Wood &
Fastener Box (Top (Top or Concrete
(Length Quantity Flange) Bottom Flange) Insulation Range
1 1/4” 1000 Up to 3/4” Up to 1/4”
1 3/4” 1000 Up to 1 1/4” Up to 3/4”
2” 1000 Up to 1 1/2” Up to 1”
3” 1000 1 1/4” to 2 1/2” 1” to 2”
4” 1000 1 1/4” to 3 1/2” 1 1/4” to 2” 2” to 3”
5” 1000 2 1/4” to 4 1/2” 2 1/4” to 3” 3” to 4”
6” 1000 3 1/4” to 5 1/2” 3 1/4” to 4” 4” to 5”
7” 1000 3 1/4” to 6 1/2” 3 1/4” to 5” 5” to 6”
8” 1000 4 1/4”to7 1/2” 4 1/4”to 6” 6”to 7”
PULLOUT VALUES
IN METAL
Gauge 18 20 22 24 26
Lbs. 913 693 534 419 277
IN PLYWOOD
Thickness 3/8” 1/2” 3/4”
Lbs. 326 436 728
IN WOOD PLANK
Depth 1” 1 1/4” 1 1/2”
Lbs. 595 916 1109
IN CONCRETE (3000 psi with 3/16 dia. pilot hole)
Depth 1” 1 1/2” 2”
Lbs. 844 1399 2227
Ultimate tensile load - 4144 lbs.
#15 ROOFGRIP
High performance mechanical
fastening of insulation and singleply
membrane to steel, wood and
structural concrete roof decks.
PRODUCT
SPECIFICATIONS
Diameter: #15
Thread form: Modified standard thread
Head Style: #3 Phillips
Drilling capacity: 18-26 gauge metal deck
Coating: Climaseal
Installation: ITW Buildex
Accudrive XL PLUS
or a standard
1,800-2,500 RPM
screwgun
SELECTOR GUIDE
Steel Insulation Range
Wood &
Fastener Box Top Top or Concrete
Length Quantity Flange Bottom Flange Insulation Range
1 1/4” 1000 Up to 3/4” Up to 1/4”
2” 1000 Up to 1 1/2” Up to 1”
3” 1000 1/2” to 2 1/2” 1/2 ” to 2”
4” 1000 1 1/4” to 31/2” 1 1/4” to 2” 1 1/2 ” to 3”
5” 1000 1 1/4” to 4 1/2” 1 1/4” to 3” 2 1/2 ” to 4”
6” 1000 2 1/4” to s i/2” 2 1/4”to 4” 3 1/2 ” to 5”
7” 500 3 1/4” to 6 1/2” 3 1/4” to 5” 4 1/2 ” to 6 ”
8” 500 4 1/4” to 7 1/2” 4 1/4” to 6” 5 1/2 ” to 7”
10” 500 6 1/4” to 9 1/2” 6 1/4” to 8” 7 1/2 ” to 9”
12” 500 8 1/4” to 11 1/2” 8 1/4” to 10” 9 1/2 ” to 11”
14” 500 10 1/4” to 13 1/2” 10 1/4” to 12” 11 1/2”
PULLOUT VALUES
IN METAL
Gauge 18 20 22 24 26
Lbs. 1323 928 690 586 403
IN PLYWOOD
Thickness 3/8” 1/2” 3/4”
Lbs. 342 499 804
IN WOOD PLANK
Depth 1” 1 1/4” 1 1/2”
Lbs. 747 1128 1140
IN CONCRETE (3000 psi with 3/16 dia. pilot hole)
Depth 1” 1 1/4” 1 1/2”
Lbs. 747 1120 1140
NOTE: Test results were obtained
under laboratory controlled conditions.
Appropriate safety factors should be
applied to these ultimate values.
Ultimate tensile load - 4144 lbs.
Ultimate shear load - 1957 lbs.
(800) 486-1832 www.trianglefastener.com 54

ITW BUILDEX
SCREW INSTALLATION TOOLS
55
TRIANGLE FASTENER CORPORATION

ITW BUILDEX
ROOFING PLATES
(800) 486-1832 www.trianglefastener.com 56

ITW BUILDEX
DEKSTRIP FLASHING
57
TRIANGLE FASTENER CORPORATION

ITW BUILDEX
METAL DECK FASTENING
BX 900
METAL DECK FASTENING SYSTEM
BX 14 Powder Actuated Fasteners
Fast and consistent way to attach metal deck
APPLICATIONS
• Roof and floor deck to steel framing.
• Side wall panels to steel framing.
PRODUCT FEATURES
• Small portable tool can be used for wall or roof applications.
• Cordless tool for ease of set-up and take down and quick mobility
on the job with no hoses/cords.
• MAC System prevents the pin from firing through the metal deck
if the structural steel framing is missed.
• Pins and loads are compatible with Unidek system.
• Excellent tool system for tacking steel deck prior to
increasing productivity with Unidek system.
• BX 14 pin with large washer and deep knurl provides optimal
tension and shear values.
• Patented .25 caliber 10 load disc is completely enclosed
in tool during use and is easy to change.
• Tool is small for tight fastening areas.
PART NUMBER 7279910
(800) 486-1832 www.trianglefastener.com 58

ITW BUILDEX
METAL DECK FASTENING
BX 12 AND BX 14 POWDER ACTUATED PINS AND LOADS
PINS AND LOAD SELECTOR GUIDE
LOAD
TOOLS
Steel Power Case
Thickness Pin Level Color Color Caliber BX900 *
>3/16” - 3/8” BX 14 #5 Red Brass .25 Medium** Yes
>3/8” - 1/2” BX 14 #5 Red Brass .25 Long Yes
>1/2” - 1” BX 14 #6 Purple Brass .25 Long Yes
*Uses bulk BX 14 pins only
** Long Yellow Load May Be Substituted
PINS AND LOAD ORDER GUIDE
PART Carton Carton Order
DESCRIPTION Number Quantity Weight Quantity
BX 12 pin in tube 7526900 1000 (100 tubes) 15
BX 12 pin in tube & 7528900 1000 18.5
#4 short yellow load
BX 14 pin (bulk) 7280900 1000 15
BX 14 pin in tube 7424900 1000 (100 tubes) 17
#4 long yellow load 7283900 100/1000 .43/4.6
#5 medium red load 7535900 100/1000 .34/3.72
#4 long yellow load 7283900 100/1000 .43/4.6
#5 long red load 7281900 100/1000 .44/4.7
#6 long purple load 7282900 100/1000 .45/4.8
Multiply the
square footage of
the deck by .25 to
determine
approximate
minimum pin and
load quantity
required.
PULLOVER VALUES (AVG. LBS. ULTIMATE)
Deck Gauge BX 12 BX 14
18 (.048'') 2548 2548
20 (.036'') 1537 1537
22 (.030'') 1290 1290
The values listed are ultimate averages achieved under laboratory conditions
and apply to Buildex manufactured fasteners only. Appropriate safety factors
should be applied to these values for design purposes.
BX 12
BX 14
SHEAR VALUES (AVG. LBS. ULTIMATE)
Deck Gauge BX 12 BX 14
18 (.048'') 2255 2261
20 (.036'') 1762 1721
22 (.030'') 1505 1624
PULLOUT
VALUES (AVG. LBS. ULTIMATE IN A-36 STEEL)
Fastener 1/8'' 5/32'' 3/16'' 1/4'' 1/2''
BX 12 2355 3289 3586
BX 14 4460 5020
INSTALLATION GUIDELINES
• Read operators tool manual before operating the tool.
• Only licensed operators can operate the BX 900 Powder Actuated Tool.
• Try the lowest load level first to determine the optimal color load for the application.
• Always wear safety glasses and hearing protection when operating the tool.
59
TRIANGLE FASTENER CORPORATION

ITW BUILDEX
METAL DECK FASTENING
AUTOTRAXX
STAND-UP METAL DECK FASTENING SYSTEM
ICH Traxx® Self-Drilling Fasteners
The fastest and the most consistent way to attach or stitch metal deck with screws.
APPLICATIONS
• Roof deck to steel framing.
• Roof deck to roof deck (sidelap/stitch).
• Floor deck to steel framing.
• Floor deck to floor deck (sidelap/stitch).
PRODUCT FEATURES
• Stand-up tool will increase productivity, reduce operator fatigue,
and improve quality on the job.
• ICH (Internal Conical Head) guidance system aligns the fastener
for proper socket engagement.
• Patented convex point has precise cutting edges to improve
drill performance with less effort.
• Point to thread design minimizes strip out and maximizes pullout and shear.
• Tool is complete with DeWalt DW284 drive motor.
• Climaseal® finish provides excellent corrosion resistance and tapping torque.
PART NUMBER 7284910
(800) 486-1832 www.trianglefastener.com 60

ITW BUILDEX
METAL DECK FASTENING
ICH TRAXX® SELF-DRILLING FASTENERS
AUTORAXX
Part Head Drill Drill & Tap
Number Description Style Point Capacity Applications
Stitching for Autotraxx
7108000 10-14 x 7/8”" ICH #3 .036 - .175 Stitching roof or floor deck
7110000 12-14 x 7/8”" ICH #1 .028 - .095
Structural attachments for Autotraxx
7061000 12-14 x 7/8”" ICH #4 .125 - .250 Metal deck to less than 1/2”
7065000 12-14 x 1 1/4”" ICH #4 .125 - .250 thick bar joist or beams
7068000 12-14 x 1 1/4”" ICH #5 .125 - .250
* FM and ICO approvals pending
Corrosion Resistance
Kesternich Results (DIN 50018, 2.0L)
• 30 Cycles - 10% or less red rust
Salt Spray Results (ASTM B117)
• 720 hours - 10% or less red rust
FASTENER VALUES
Fastener Tensile Shear Torque
(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)
10-14 1936 1400 61
12-14 2778 2000 92
12-24 T/4 3020 2100 100
12-24 T/5 3188 2200 150
PULLOVER VALUES
(AVG. LBS. ULT.)
Metal Deck
Gauge Pullover
18 1830
20 1452
22 1087
PULLOUT VALUES (AVERAGE LBS. ULTIMATE)
Fastener
Steel Gauge
Dia. Pt.. 26 24 22 20 18 16 14 12 3/16 1/4
10 3 124 208 266 299 499 708 967 1474
12 1 159 281 338 390 649 908 1259
12 3 551 757 1063 2998
12 4 986 1532 3485 4013
12 5 913 1527 3700 3999
The values listed are ultimate averages achieved under laboratory
conditions and apply to Buildex manufactured fasteners only. Appropriate
safety factors should be applied to these values for design purposes.
INSTALLATION GUIDELINES
• Autotraxx or Fastraxx stand-up installation tool is recommended for optimal
fastener performance. If a standard screw gun is used it should be a minimum
of 4 amps and have a RPM range of 0-2000.
• Adjust the Autotraxx/Fastraxx or screw gun nosepiece to properly seat the
fastener.
• The fastener is fully seated when the head is flush with the work surface.
• Overdriving may result in torsional failure of the fastener or strip out of the
substrate.
•The fastener must penetrate beyond the metal structure a minimum of 3 pitches
of thread.
• Use a heavy gauge extension cord such as a 14 or 12 gauge to prevent voltage
drops and damage to the drive motor.
APPROVALS AND LISTINGS
• Factory Mutual (J.I. 2 X 942 AM)
and J.I..1 x 7A2.AM.
• ICBO ER3056 & ER4254
• City of Los Angeles Approval
• Steel Deck Institute listed.
ICBO Listed
61
TRIANGLE FASTENER CORPORATION

SPAN-MASTER
BRIDGE DECK FASTENER
S P A N
MASTER
BRIDGE DECK FASTENER
Triangle Fastener is pleased to introduce SPANMASTER, the
first fastener designed specifically for bridge deck
construction.
Through extensive research and product development, we’ve
developed a fastener that reduces fastener failure, and
increases productivity.
Here’s what makes SpanMaster work...
Span-Master with
Radial Indent
Ordinary
Fastener
FASTENER STRENGTH (Ultimate)
Torsional 150 inch pounds
Tensile 3850 pounds
Shear 2600 pounds
Special radial indent
increases bearing surface
and and distributes stress
Radius under the
fastener head
concentrates stress.
PART NUMBER
141000HW3C
APPLICATION
Used for fastening bridge decking to steel support
angles.
PHYSICAL & MECHANICAL PROPERTIES
Description: 1/4-14 x 1” self-drilling fastener
with radial indent under washer face.
Point Type: Type 3 self-drilling point with long
pilot section.
Head Style: 3/8” Hex washer head.
Material: C1018-1022 carbon steel
Heat Treatment: Case hardened to SAE J-78
specification
Finish: .0005 min mechanical cadmium
(Meets PENNDOT specifications)
Pullout Strength in Steel
(Ultimate in Pounds)
18 ga ( .048”) -- 613 lbs
16 ga (.060”) -- 883 lbs
14 ga (.075”) -- 1148 lbs
12 ga ( .105”) -- 1861 lbs
3/16” (.1875”) -- 4553 lbs
1/4” (.250”) -- 5036 lbs
(800) 486-1832 www.trianglefastener.com 62

ITW BUILDEX
COATING INFORMATION
CORROSION RESISTANT COATINGS
The roofing industry's most complete selection of long-life corrosion resistant
fastener coatings.
SPEX STANDARD COATING
For reliable long-life corrosion resistance.
A specially formulated epoxy coating, SPEX exceeds the
corrosion resistance requirements of Factory Mutual
Specification #4470.
SPEX is engineered to be extremely tough and chip resistant.
Its fully cross-linked matrix system minimizes marring and
scraping during installation.
State-of-the-art electro-deposition application and curing
processes provide excellent adhesion to the fastener and
uniform coating thickness. SPEX will not clog Phillips
recesses.
_________________________________________________________________________________________________
ITW Buildex
1349 W. Bryn Mawr Ave.
Itasca, Illinois 60143
Telephone 630-595-3500
Fax 630-595-3549
January 16, 2004
SPEX TECHNICAL DATA
Chemical identification: Epoxy coating
Cure: Thermoset
D1N 50018, 2.O liter SO : Exceeds Factory Mutual #4470
(15 cycles with less than 15% red rust)
Humidity ASTM D2247: Excellent
Mar/chip resistance: Excellent
Abrasion/shear resistance: Excellent
Film hardness: Tough/durable
Impact resistance: Excellent
To:
Valued Buildex Customer
From: Dan Kenny, Technical Services Manager
Re:
ACQ Treated Wood Applications
By now you have probably heard of the changes with pressure-treated woo
The industry standard Chromated Copper Arsenate (CCA) pressure-treated
wood is no longer being produced for residential use. We have completed
testing of our fasteners with one of the common pressure-treated wood
alternatives know as Alkaline Copper Quaternary (ACQ).
Our test results indicate that ACQ pressure-treated wood is more corros
metal fasteners than CCA pressure-treated wood. However, the test resu
suggest that most of our barrier coatings appear to hold up well in ACQ
wood applications.
We recommend the use of the following fasteners for ACQ treated wood
applications:
DEC-KING® Exterior Wood Screw with Climacoat
Tapcon® Concrete Anchor with Blue Climaseal or White UltraShield
Wood-To-Metal TEKS® with Grey Spex
Roofgrip® with Spex or Blue Climaseal
GYP-FAST Nail with Climacoat
Maxi-Set Tapcon® White UltraShield
CLIMASEAL PREMIUM COATING
The ultimate in corrosion resistant coatings for roofing
fasteners.
A proprietary epoxy coating. Climaseal has been
developed to provide the ultimate in corrosion
resistance properties for roofing fasteners.
Buildex engineering tests performed in strict
accordance with Kesternich DIN 50018, 2.0 liter 502
consistently show Climaseal substantially exceeds the
corrosion resistance requirements of Factory Mutual
Specification #4470.
Climaseal is applied over SPEX coating, effectively
combining the strength and abrasion resistance of
SPEX with the added corrosion resistance of Climaseal.
Climaseal completely seals the fastener which further
enhances corrosion resistance.
As we continue to test other coatings and alternative preservative trea
updates will be provided.
Due to the many variables involved, including the chemical retention le
wood, species of wood and environmental factors, estimates of the servi
our fasteners in these applications cannot be provided. In addition, th
change any of the terms of our existing warranty.
Should you have any questions, please feel free to call the Technical
Department at (800) 323-0720.
Climaseal , SPEX and Building Ideas That
Work are trademarks of ITW Buildex and
Illinois Tool Works Inc.
CLIMASEAL TECHNICAL DATA
Chemical identification: Epoxy polymer coating
Cure: Thermoset
DIN 50018, 2.0 liter S02: Substantially exceeds
Factory Mutual #4470
(15 cycles with less than 15% red rust)
Humidity ASTM D2247: Excellent
Mar/chip resistance: Excellent
Abrasion/shear resistance: Tough/durable
Impact resistance: Excellent
63
TRIANGLE FASTENER CORPORATION

TRUF
UFAST
TERMINATION BARS
TB-50
Termination
Bar with
Sealant Ledge
Material: Specially extruded aluminum without sharp edges.
Dimensions: .050 thick x 1” wide x 10’ long per piece.
Holes: 1/4” x 3/8” slotted holes on 6”, 8” or 12” centers.
Packaged: 50 pieces per tube.
Approx. Shipping Weight: 45 pounds per tube.
TB-75
TERMINATION
BAR WITH
SEALANT LEDGE
Material: Specially extruded aluminum without sharp edges.
Dimensions: .075 thick x 1” wide x 10’ long per piece.
Holes: 1/4” x 3/8” slotted holes on 6”, 8” or 12” centers.
Packaged: 50 pieces per tube.
Approx. Shipping Weight: 51 pounds per tube.
TB-85
TERMINATION
BAR WITH
SEALANT LEDGE
TB-100
TERMINATION
BAR WITH
SEALANT LEDGE
Material: Extruded aluminum without sharp edges.
Dimensions: .085 thick x 1” wide x 10’ long per piece.
Holes: 1/4” x 3/8” slotted holes on 6”, 8” or 12” centers.
Packaged: 25 pieces per tube.
Approx. Shipping Weight: 43 pounds per tube.
Material: Specially extruded aluminum without sharp edges.
Dimensions: .100” thick x 1” wide x 10’ long per piece.
Holes: 1/4” x 3/8” slotted holes on 6”, 8” or 12” centers.
Packaged: 50 pieces per tube.
Approx. Shipping Weight: 68 pounds per tube.
TB-125
TERMINATION
BAR WITH
SEALANT LEDGE
RD-100
RETAINING
DRAINBAR
Material: Specially extruded aluminum without sharp edges.
Dimensions: .125” thick x 1” wide x 10’ long per piece.
Holes: 1/4” x 3/8” slotted holes on 6”, 8” or 12” centers.
Packaged: 50 pieces per tube.
Approx. Shipping Weight: 78 pounds per tube.
For use with Ballasted or Non-Ballasted Systems
Material: Specially extruded aluminum without sharp edges.
Dimensions: .100” thick x 1” wide x 10’ long per piece.
Mounting Holes: 1/4” x 3/8” slotted holes on 6” centers.
Packaged: 10 pieces per tube.
Drainage Slots: 3/8” x 1 1/2” slotted drain holes on 4”
centers
Approx. Shipping Weight: 78 pounds per tube.
LIMITED WARRANTY
Tru-Fast hereby gives, to the original purchaser only, a warranty for defects in manufacture or workmanship on its products for ten (10) years from
date of purchase. This warranty is in lieu of all other warranties, express, implied or statutory. This warranty is also in lieu of any other obligations
and liabilities on the part of Tru-Fast. Tru-Fast’s sole obligation under this warranty shall be replacement of the Tru-Fast product which is deemed to
be defective. Tru-Fast neither assumes nor authorizes any person to assume for it or any other obligation or liability whatsoever in connection with its
products. In no event shall Tru-Fast be liable for special, consequential or incidental damages for breach of said warranty, nor for the improper
selection of Tru-Fast Products a particular application.
(800) 486-1832 www.trianglefastener.com 64

ES PRODUCTS
BASE PLY FASTENERS
FM-90
FASTENING GUIDE CLASS I-90
WINDSTORM CLASSIFICATION
BASE PLY ATTACHMENT TO
LIGHTWEIGHT INSULATING
CONCRETE
An FMRC Approved base ply is secured to an FMRC
Approved lightweight insulating concrete roof deck as
outlined in the current edition of the FMRC Approval
Guide.
The base ply is secured with FM-90 Fasteners
installed 7-1/2 in. on center in the 4 in. wide side laps
and 7-1/2 in. on center, staggered in 2 rows, equally
spaced, between the base ply side laps.
When fastening with this pattern, expect to use
approximately 165 fasteners per square (100 ft2)
when installing meter-wide material.
IMPORTANT:
Prior to roofing, on-site withdrawal testing should
always be performed to evaluate the ability of the
roofing substrate to satisfactorily accept and retain
fasteners. Such testing may alter fastening selection
and modify applicable fastening patterns.
ES Products’
Magnetic Driver
39” overall
length.
Disk: Integrally locked to fastener. Precision formed from
corrosion resistant Galvalume (AZ-55) steel to prevent
corrosion. Rib reinforced cap, 2.7” diameter.
Technical Data:
Approvals: FM-90 fasteners maintain Factory Mutual, Underwriters Lab,
and Metro-Dade County Approvals.
Fastening Pattern: Consult Factory Mutual, Underwriters Lab, or Metro-
Dade requirements for recommended patterns in normal, exposed, and
hurricane areas.
Field Testing: On-site withdrawal testing should always be performed to
evaluate the ability of the roofing substrate to satisfactorily accept and
retain fasteners. Such testing may alter fastener selection and modify
applicable fastening patterns.
Installation:
Equipment: Always use the ES Magnetic Driver
to assure proper fastener installation.
Method: Drive FM-90 as an ordinary nail. DO NOT TOE.
Seat cap flush with roofing surface (see illustration).
Operation: As FM-90 is driven, dual legs diverge and cut a plug of deck
material which wedges and anchors the FM-90 in its own hole. No
predrilling is required.
Availability: FM-90 is a patented product manufactured only by ES
Products, Inc. distributed by leading roofing material and equipment
wholesalers throughout the United States.
Packaging: 1,000 FM-90 fasteners per carton. Shrink wrapped and
palletized. Gross weight: 38 lbs.
3.75”
7.5”
Face of Driver
Length: 1.7 inches
Diameter: 2.7 inches
7.5”
4”
Equally Spaced
Use only Approved
base ply materials.
Elastomeric polymer coating
protects exposed surfaces of
fastener from corrosion.
Galvalume (AZ-55) roofing
disk is integrally attached to
fastener.
Using the FM-90
Fastener density and spacing vary depending on applicable uplift
requirements. Local codes, governing Approval bodies, membrane
manufacturers, and individual roof deck manufacturers all may have
specific requirements that need to be addressed prior to beginning any
roofing project.
The following illustrates a typical Factory Mutual Approved fastening
pattern widely accepted for use by membrane and roof deck
manufacturers.
Composition:
Fastener: Precision formed from corrosion resistant Galvanized
(G-90) steel. Exposed surfaces are further protected with a
special elastomeric polymer coating to prevent corrosion.
Rectangular dual gripping legs, 1.7” long.
Galvanized steel (G-90) legs bond to the
lightweight concrete. Holding power
increases over time.
Fastener anchors itself in its own hole by
cutting an inverted wedge of concrete. No
predrilling required.
UL ®
METRO-DADE
65
TRIANGLE FASTENER CORPORATION

ES PRODUCTS
BASE PLY FASTENERS
FM-75
BASE PLY ATTACHMENT TO
HIGHER DENSITY
LIGHTWEIGHT INSULATING
CONCRETE
FASTENING GUIDE
CLASS I-90 WINDSTORM CLASSIFICATION
An FMRC Approved base ply is secured to an FMRC
Approved lightweight insulating concrete roof deck as
outlined in the current edition of the FMRC Approval
Guide.
The base ply is secured with FM-75 Fasteners
installed 7-1/2 in. on center in the 4 in. wide side laps
and 7-1/2 in. on center, staggered in 2 rows, equally
spaced, between the base ply side laps.
When fastening with this pattern, expect to use
approximately 165 fasteners per square (100 ft2)
when installing meter-wide material.
IMPORTANT:
Prior to roofing, on-site withdrawal testing should
always be performed to evaluate the ability of the
roofing substrate to satisfactorily accept and retain
fasteners. Such testing may alter fastening selection
and modify applicable fastening patterns.
ES Products’
Magnetic Driver
39” overall
length.
Disk: Integrally locked to fastener. Precision formed from
corrosion resistant Galvalume (AZ-55) steel to prevent
corrosion. Rib reinforced cap, 2.7” diameter.
Technical Data:
Approvals: FM-75 fasteners maintain Factory Mutual, Underwriters Lab,
and Metro-Dade County Approvals.
Fastening Pattern: Consult Factory Mutual, Underwriters Lab, or Metro-
Dade requirements for recommended patterns in normal, exposed, and
hurricane areas.
Field Testing: On-site withdrawal testing should always be performed to
evaluate the ability of the roofing substrate to satisfactorily accept and
retain fasteners. Such testing may alter fastener selection and modify
applicable fastening patterns.
Installation:
Equipment: Always use the ES Magnetic Driver to assure proper
fastener installation.
Method: Drive FM-75 as an ordinary nail. DO NOT TOE. Seat cap flush
with roofing surface (see illustration).
Operation: As FM-75 is driven, dual legs diverge and cut a plug of deck
material which wedges and anchors the FM-75 in its own hole. No
predrilling is required.
Availability: FM-75 is a patented product manufactured only by ES
Products, Inc. distributed by leading roofing material and equipment
wholesalers throughout the United States.
Packaging: 1,000 FM-75 fasteners per carton. Shrink wrapped and
palletized. Gross weight: 34 lbs.
3.75”
7.5”
Length: 1.2 inches
Diameter: 2.7 inches
7.5”
4”
Equally Spaced
Face of Driver
Use only Approved base
ply materials.
Elastomeric polymer coating
protects exposed surfaces of
fastener from corrosion.
Galvalume (AZ-55) roofing disk
is integrally attached to fastener.
Using the FM-75
Fastener density and spacing vary depending on applicable uplift
requirements. Local codes, governing Approval bodies, membrane
manufacturers, and individual roof deck manufacturers all may have
specific requirements that need to be addressed prior to beginning any
roofing project.
The following illustrates a typical Factory Mutual Approved fastening
pattern widely accepted for use by membrane and roof deck
manufacturers.
Composition:
Fastener: Precision formed from corrosion resistant Galvanized (G-90)
steel. Exposed surfaces are further protected with a special elastomeric
polymer coating to prevent corrosion. Rectangular dual gripping legs,
1.2” long.
Galvanized steel (G-90) legs bond
to the lightweight concrete.
Holding power increases over
time.
Fastener anchors itself in its own
hole by cutting an inverted wedge
of concrete. No predrilling
required.
UL ®
METRO-DADE
(800) 486-1832 www.trianglefastener.com 66

ES PRODUCTS
BASE PLY FASTENERS
TWIN LOC-NAIL
RECOVERY BOARD
OR BASE PLY TO
WOOD FIBER /
POURED GYPSUM
USING THE TWIN LOC-NAIL
Fastener density and spacing vary depending on applicable uplift
requirements. Local codes, governing Approval bodies, membrane
manufacturers, and individual roof deck manufacturers all may have
specific requirements that need to be addressed prior to beginning any
roofing project. The Twin Loc-Nail should always be embedded in the
structural roof deck to a depth of at least 1”.
COMPOSITION
Factory preassembled components consisting of:
1.8”
2.7”
Tube: Precision formed from Galvalume (AZ-55) coated steel to prevent
corrosion. The 1.8” long tube is shaped to easily penetrate decking and
existing membranes.
Disk: Precision formed from Galvalume (AZ-55) coated steel to prevent
corrosion. Securely clamped to the tube, 2.7” diameter, rib reinforced to
resist cupping.
Roofing disk is securely clamped to
the tube.
Factory preinserted staple.
Recovery Board
Locking Staple: Precision formed from .080” diameter high tensile steel
wire. Coated to prevent corrosion. Factory preinserted into tube.
TECHNICAL DATA
Approvals: Twin Loc-Nail maintains Factory Mutual and
Metro-Dade County Approvals.
Fastening Pattern: Consult Factory Mutual or Metro-Dade County
requirements for recommended patterns in normal, exposed, and
hurricane areas.
Existing membrane
Field Testing: On-site withdrawal testing should always be performed to
evaluate the ability of the roofing substrate to satisfactorily accept and
retain fasteners. Such testing may alter fastener selection and modify
applicable fastening patterns. The Twin Loc-Nail should always be
embedded in the structural roof deck to a depth of at least 1”.
INSTALLATION
Equipment: Always use ES Products’ Twin Loc Driver. The specially
designed Driver assures consistent speedy application. ES Nail Pouch
holds up to 10 times the quantity of fasteners accommodated by standard
nailing aprons.
FIRST IMPACT SETS TUBE.
SECOND IMPACT ACTUATES STAPLE.
Method: Using ES Products’ Twin Loc Driver, two impacts are required.
Place fastener on face of driver positioning exposed staple into slot in
driver face. Drive fastener with vertical motion into roof deck with first
impact seating cap flush with roof deck. With second impact, drive the
locking staple thru the tube/disk unit into the deck until the top of the
staple is flush with the cap (see illustration).
Operation: When locking staple is driven, its dual wire legs diverge
anchoring the fastener in place (see illustration). Uplift resistance may
vary depending on the density and integrity of the substrate.
Availability: Twin Loc-Nail is a patented product manufactured only by ES
Products, Inc., distributed by leading roofing material and equipment
wholesalers.
As locking staple is driven, it’s dual wire legs diverge
anchoring the fastener in place.
Packaging: 500 Twin Loc-Nails per carton. Shrink wrapped and palletized.
Gross weight: 33 lbs.
METRO-DADE
67
TRIANGLE FASTENER CORPORATION

ES PRODUCTS
BASE PLY FASTENERS
DO-ALL LOC-NAIL
SHINGLE OR BASE PLY
ATTACHMENT TO GYPSUM
BOARD ROOF DECKS
COMPOSITION
Fastener: precision formed one-piece steel construction featuring dual
serrated legs with sharp angular points. Available in zinc plated steel or
in Stainless Steel for superior corrosion resistance.
2 LENGTHS:
STANDARD: 1.375”
LONG: 1.75”
Cap: Use with Do-All Loc-Nail for base ply attachment. 1.2” Diameter.
Precision formed zinc plated steel with reinforcing asphalt barrier ring.
TECHNICAL DATA
Approvals: Approved and specified for shingle attachment to
Loadmaster roof deck assemblies.
1.375”
1.75”
1.2”
Fastening Pattern: Consult deck and shingle/membrane
manufacturer requirements for recommended patterns in
normal, exposed and hurricane areas. Typical shingle attachment uses
6 Do-Alls per shingle.
Field Testing: On-site withdrawal testing should always be
performed to evaluate the ability of the roofing substrate to
satisfactorily accept and retain fasteners. Such testing may alter
fastener selection and modify applicable fastening patterns.
INSTALLATION
Equipment: Use an ordinary roofer’s hammer. No special tools required.
Method: Drive Do-All Loc-Nail as an ordinary nail. DO NOT TOE. Seat
head/cap flush with roofing surface.
Operation: As Do-All Loc-Nail is driven, dual legs diverge and
serrations grip substrate. No pre-drilling required. Uplift resistance may
vary depending on the density and integrity of the substrate.
Availability: Do-All Loc-Nail is a patented product manufactured only by
ES Products, Inc., distributed by leading roofing material and equipment
wholesalers.
Packaging: 2500 Do-All Loc-Nails per carton. Shipping weights: 1.375” -
13 lbs.; 1.75” - 16 lbs. 2500 Caps per carton, shipping weight: 9 lbs.
Approved and specified for shingle application to
Loadmaster Roof deck Assemblies.
(800) 486-1832 www.trianglefastener.com
68

ES PRODUCTS
BASE PLY FASTENERS
NAIL-TITE
BASE PLY TO POURED
GYPSUM ROOF DECKS
NAIL-TITE TYPE A - 1.5”
NAIL-TITE TYPE R - 1.0”
Using NAIL-TITE Type A or NAIL-TITE Type R
Fastener density and spacing vary depending on applicable uplift
requirements. Local codes, governing Approval bodies, membrane
manufacturers, and individual roof deck manufacturers all may have
specific requirements that need to be addressed prior to beginning any
roofing project.
The following illustrates a typical Factory Mutual Approved fastening
pattern widely accepted by membrane and roof deck manufacturers.
NAIL-TITE TYPE A
For softer gypsum decks
Use only Approved base ply
materials.
1.5”
NAIL-TITE TYPE R
For harder gypsum decks
Cap is integrally attached to
fastener.
1.0”
IMPORTANT:
Prior to roofing, on-site withdrawal testing should always be performed
to evaluate the ability of the roofing substrate to satisfactorily accept
and retain fasteners. Such testing may alter fastener selection and
modify applicable fastening patterns.
COMPOSITION
Shank: Tapered cone precision formed from corrosion resistant
galvanized (G-90) steel.
Cap: 1.7” round cap formed from corrosion resistant Galvalume (AZ-55)
steel, reinforced to resist cupping during driving.
Assembly: Shank securely swaged to cap forming rigid one piece fastener.
TECHNICAL DATA
Approvals: NAIL-TITE maintains Factory Mutual and Metro-Dade
County Approvals.
Fastening Pattern: Consult Factory Mutual or Metro-Dade County
requirements for recommended patterns in normal, exposed, and
hurricane areas. (Typical pattern illustrated on reverse.)
Field Testing: On-site withdrawal testing should always be performed to
evaluate the ability of the roofing substrate to satisfactorily accept and
retain fasteners. Such testing may alter fastener selection and modify
applicable fastening patterns.
INSTALLATION
Equipment: Always use ES Products’ Nail-Tite Driver. The specially
designed Driver assures consistent speedy application. ES Nail Pouch
holds up to 10 times the quantity of fasteners accommodated by
standard nailing aprons.
Method: Place fastener on face of driver. Drive fastener with vertical
motion into roof deck seating cap flush with roofing surface (see
illustration). DO NOT TOE.
As fastener is driven, shank cones out cutting a plug of deck material
which wedges and anchors the fastener in its own hole. No predrilling
required.
Fastening Guide Class I-60 or I-90 Windstorm
Classification
An FMRC Approved base ply is fastened to a Gypsum
roof deck as outlined in the current edition of the FMRC
Approval Guide.
The base ply is fastened with Nail-Tite Type A or Nail-Tite
Type R base ply fasteners installed 9 in. on center in the 2
in. wide base ply side laps and 18 in. on center staggered
in 2 rows, equally spaced, between the base ply side laps.
When fastening meter-wide material with this pattern,
expect to use approximately 86 fasteners per square (100
FT2).
9”
18”
NAIL-TITE DRIVER
FACE OF DRIVER
Operation: As NAIL-TITE is driven, shank cones out and cuts a plug of
deck material which wedges and anchors the NAIL-TITE in its own
hole. No predrilling required. Uplift resistance may vary depending on
the density and integrity of the substrate.
Availability: NAIL-TITE fasteners are patented products manufactured
only by ES Products, Inc., distributed by leading roofing material and
equipment wholesalers.
Packaging: 3,000 NAIL-TITE fasteners per carton. Shrink wrapped and
palletized. Gross weight: Type A: 44 lbs.; Type R: 37 lbs.
9”
2”
Equally Spaced
METRO-DADE
69
TRIANGLE FASTENER CORPORATION

ES PRODUCTS
BASE PLY FASTENERS
INSULDECK
LOC-NAIL
BASE PLY TO TECTUM®
WOOD FIBER ROOF
DECKS
COMPOSITION
Fastener: Precision formed from Galvalume (AZ-55) coated steel to
prevent corrosion. The 1.7” long dual shank with fine angular point easily
penetrates Tectum® decks. The shank is self-clinching when driven.
1.7”
Roofing disk is integrally
attached to fastener.
2.7”
Disk: Precision formed from Galvalume (AZ-55) coated steel to prevent
corrosion. Securely clamped to shank, 2.7” diameter, rib reinforced to
resist cupping when driven.
TECHNICAL DATA
Approvals: Insuldeck Loc-Nail maintains Factory Mutual and Metro-
Dade County Approvals.
Fastening Pattern: Consult Factory Mutual or Metro-Dade County
requirements for recommended patterns in normal, exposed, and
hurricane areas. (Typical patterns illustrated on reverse.)
As fastener is driven, an automatic knee bend
effect takes place in the shank of the fastener
locking it securely in place.
METRO-DADE
Field Testing: On-site withdrawal testing should always be
performed to evaluate the ability of the roofing substrate to
satisfactorily accept and retain fasteners. Such testing may alter
fastener selection and modify applicable fastening patterns.
INSTALLATION
Equipment: Always use ES Products’ Insuldeck Driver. The
specially designed Driver assures consistent speedy application. ES
Nail Pouch holds up to 10 times the quantity of fasteners
accommodated by standard nailing apron.
INSULDECK
DRIVER
7.5”
3.75”
Method: Place fastener on face of driver. Driver self-centers
fastener and holds fastener perpendicular to face. Drive fastener with
vertical motion into roof deck. DO NOT TOE.
Operation: When cupped head is driven flush against rigid cap, an
automatic knee bend effect takes place in the shank of the fastener
(see illustration) locking fastener in place. Uplift resistance may vary
depending on the density and integrity of the substrate.
Availability: Insuldeck Loc-Nail is a patented product manufactured only
by ES Products, Inc., distributed by leading roofing material and
equipment wholesalers.
Packaging: 1,000 Insuldeck Loc-Nails per carton. Shrink wrapped and
palletized. Gross weight: 28 lbs.
Using the INSULDECK LOC-NAIL
Fastener density and spacing vary depending on applicable
uplift requirements. Local codes, governing Approval bodies, membrane
manufacturers, and individual roof deck manufacturers all may have
specific requirements that need to be addressed prior to beginning any
roofing project.
The following illustrates typical Factory Mutual Approved fastening
patterns widely accepted for use by membrane and roof deck
manufacturers.
IMPORTANT:
Prior to roofing, on-site withdrawal testing should always be
performed to evaluate the ability of the roofing substrate to
satisfactorily accept and retain fasteners. Such testing may alter
fastener selection and modify applicable fastening patterns.
FACE OF
DRIVER
FASTENING GUIDE I CLASS I-90
WINDSTORM CLASSIFICATION
An FMRC Approved base ply is secured to an FMRC Approved
TECTUM® roof deck as outlined in the current edition of the FMRC
Approval Guide.
The base ply is secured with Insuldeck Loc-Nails installed 7-1/2 in. on
center in the 4 in. wide side laps and 7-1/2 in. on center staggered in 2
rows, equally spaced, between the base ply side laps. When fastening
meter-wide material with this pattern, expect to use approximately 165
fasteners per square (100 ft2).
FASTENING GUIDE II CLASS I-60
WINDSTORM CLASSIFICATION
An FMRC Approved base ply is secured to an FMRC Approved Tectum
wood fiber roof deck as outlined in the current edition of the FMRC
Approved Guide.
The base ply is secured with Insuldeck Loc-Nails installed 9 in. on
center in the 4 in. wide side laps and 12 in. on center staggered in 2
rows, equally spaced, between the base ply side laps.
When fastening meter-wide material with this pattern, expect to use
approximately 114 fasteners per square (100 FT2).
7.5”
4”
Equally Spaced
(800) 486-1832 www.trianglefastener.com 70

ES PRODUCTS
BASE PLY FASTENERS
FASTENING PATTERNS FOR BASE PLY FASTENERS
The following illustrates typical Factory Mutual recommended fastening
patterns widely accepted by membrane and roof deck manufacturers.
6”
6”
Fastening Guide 1
Recovery Board Attachment Under Fully Adhered Single Ply Membranes.
+
+
+
6”
Class I-60 or I-75 Windstorm Classification.
An FMRC Approved recovery board suitable for use with fully adhered
single ply membranes is fastened with 9 Twin Loc-Nails per 4’ x 4’ board
in 3 rows of 3 fasteners per row.
Consult FMRC for a complete listing of Approved recovery boards.
+ + +
+ + +
9 Fasteners
6”
Fastening Guide 2
Recovery Board Attachment Under Fully Adhered Single Ply
Membranes.
Class I-90 Windstorm Classification.
6”
12”
6” 6”
+ + +
+ + +
An FMRC Approved recovery board suitable for use with fully adhered
single ply membranes is fastened with 12 Twin Loc-Nails per 4’ x 4’ board
in 4 rows of 3 fasteners per row.
Consult FMRC for a complete listing of Approved recovery boards.
6”
12”
12”
+ + +
+ + +
12 Fasteners
Fastening Guide 3
Recovery Board Attachment Under Built-Up and
Modified Bitumen Roof Covers.
Class I-90 Windstorm Classification.
An FMRC Approved recovery board suitable for use with
minimum 3 ply built-up or modified membranes is fastened with
8 Twin Loc-Nails per 4’ x 4’ board in a diamond in a box pattern.
12”
24”
6”
+ +
+
+
+
6”
Consult FMRC for a complete listing of
Approved recovery boards.
+
+
+
8 Fasteners
Fastening Guide 4
Base Ply Attachment for Built-Up or Modified Bitumen
Roof Covers.
Class I-60, I-75, or I-90 Windstorm Classification.
An FMRC Approved base ply is fastened with Twin-Loc Nails installed 9”
on center in the 2” wide base ply side laps and 18” on center staggered
in 2 rows, equally spaced, between the
base ply side laps.
When fastening meter-wide material with this pattern, expect to use
approximately 86 fasteners per square (100 FT 2 ).
9”
18”
2”
9”
71
TRIANGLE FASTENER CORPORATION

OMG FASTENERS FOR LIGHTWEIGHT DECKS
TOGGLE BOLT
STANDARD OR
ASSEMBLED
FAST FACTS
PLATES & ACCESSORIES
Use a 2" or 3" steel or plastic plate, depending
upon the application.
Use a 3/4" drill bit.
COATING
Olympic CR-10 corrosion resistant coating
exhibits less than 15% red rust after 30
Kesternich cycles. CR-10 coating exceeds
F.M. Approval Standard 4470.
Designed to attach
insulation to gypsum, all
cementitious wood fiber,
Tectum® and lightweight
concrete decks or decks
where conditions require
a positive locking
fastener.
Thread
PHYSICAL DATA Cat. No. Length Length Packaging Weight
The data below is constant for CRT04 4" 3" 500 23 lb
each Olympic Toggle Bolt. CRT06 6" 4" 500 34 lb
CRT07 7" 4" 500 39 lb
Thread Diameter: .250 CRT08 8" 4" 500 43 lb
Head Height: .125 CRT10 10" 4" 250 27 lb
Head Diameter: .435 CRT12 12" 4" 250 34 lb
Head Style: #3 Phillips CRT14 14" 4" 250 37 lb
Truss Head* CRT16 16" 4" 250 42 lb
Coating: CR-10
ASSEMBLED TOGGLE BOLTS**
Toggle Height: 1.125 RST04** 4" 3" 250 27 lb
(Closed) RST06** 6" 4" 250 32 lb
Toggle Spread: 2.25 RST07** 7" 4" 250 34 lb
*#3 phillips bit included in RST08** 8" 4" 250 37 lb
each carton. RST10** 10" 4" 250
42 lb
RST12** 12" 4" 150 29 lb
RST14** 14" 4" 150 32 lb
RST16** 16" 4" 150 34 lb
FEATURES & BENEFITS
• F.M. and Dade County approved.
• Assembled Toggle Bolt saves time and money on job.
• The Olympic Toggle Bolt is a positive locking fastener.
NTB-1HWO
FAST FACTS
A glass-filled nylon auger
fastener with a 1" head
designed to secure
insulation and single-ply
membrane to gypsum, all
cementitious wood fiber,
Tectum® and certain
lightweight concrete decks.
PHYSICAL DATA CAT. NO. LENGTH PACKAGING WEIGHT
The data below is constant for NTB1025WO 2 1/2" 500 13 lb.
each Olympic NTB-1HWO NTB1030WO 3" 500 15 lb.
NTB1035WO 3 1/2" 500 17 lb.
Head Size:1" Diameter NTB1040WO 4" 500 19 lb.
NTB1045WO 4 1/2" 500 21 lb.
Head Style:Double Internal NTB1050WO 5" 500 24 lb.
Hex Drive NTB1055WO 5 1/2" 500 26 lb.
NTB1060WO 6" 500 28 lb.
Major NTB1065WO 6 1/2" 500 29 lb.
Thread NTB1070WO 7" 500 30 lb.
Diameter: .750 NTB1075WO 7 1/2" 500 32 lb.
NTB1080WO 8" 250 16 lb.
Thread: 3.5 T.P.I. Buttress NTB1085WO 8 1/2" 250 17 lb.
NTB1090WO 9" 250 18 lb.
Material: Glass-Filled Nylon NTB1095WO 9 1/2" 250 19 lb.
NTB1100WO 10" 250 20 lb.
FEATURES & BENEFITS
• Thread design & large root diameter:
• Increase pullout resistance
• Increase side shear strength
• Made from glass-filled nylon which:
• Eliminates corrosion
• Eliminates thermal bridging and condensation
• Yields high tensile strength
• F.M.0 and Dade County approved.
PLATES & ACCESSORIES
Use 3" steel plate, 2" steel plate (with barbs), or batten bar.
Use a carbide tip drill bit for gypsum, lightweight concrete and
some cementitious wood fiber applications.
(800) 486-1832 www.trianglefastener.com 72

OMG FASTENERS FOR LIGHTWEIGHT DECKS
NC FASTENER
FAST FACTS
Designed for attaching insulation and single-ply membrane to
fiberglass reinforced plastics, light gauge metal and decks in
highly humid or corrosive atmospheres.
FEATURES & BENEFITS
• Made of a specially formulated nylon which:
• Eliminates thermal bridging.
• Eliminates fastener corrosion.
• Preassembled nut & bolt design offers:
• High pullout values in fiberglass reinforced
decks and marginal metal decks.
• Increased back out resistance.
• The 2" built-in stress plate:
• Reduces installation time.
• Prevents fastener pop-up.
• F.M. and Dade County approved.
Physical Data Cat. No. Length Packaging Weight
The data below is NC1 04 4" 500 14 lb
constant for each NC1O6 6" 500 17 lb
NC Fastener. NC1O8 8" 500 191b
NC11O 10" 500 231b
Head Diameter: 1 "or 2" NC112 12" 500 271b
Head Height: .100 or .260 2" BUILT-IN STRESS PLATE
Head Style: NC204 4" 500 23 lb
Double Internal NC206 6" 500 26 lb
Hex Head NC208 8" 500 29 lb
Material: Nylon NC21O 10" 250 15 lb
Body Diameter: 290 NC212 12" 250 181b
NC FASTENER LENGTH SELECTION PROCEDURE
Combined Thickness Of Membrane
and/or Existing Substrate
NC Fastener Minimum Total Maximum Total
Length Thickness Thickness
4" 1 1/4” 3 3/4”
6" 2 1/2” 5 3/4”
8" 4 1/2” 7 3/4”
10" 6 1/2” 9 3/4”
12" 8 1/2” 11 3/4”
PLATES & ACCESSORIES
There are various 2” and 3” plate combinations..
Use a high speed steel or centering drill bit.
73
TRIANGLE FASTENER CORPORATION

LEISTER
HOT AIR TOOLS FOR ROOFING
VARIMAT
• Temperature and welding speed electronically controlled
• Compact, easily maneuverable, can be used for all roofing membranes
• Independent suspension pressure roller guarantees even distribution
of pressure across width of welding seam
• Digital display of set and actual value of the welding speed and temperature
• Micro-controller provides further options to meet customers specifications
TRIAC “S”
BASIC ROOF WELDING KIT
• Tool box for Triac kit
• 40mm hand roller
• 30B1 wide slot nozzle 4OMM
TRIAC “S”
DELUXE ROOF WELDING KIT
• 30B1 wide slot nozzle 4OMM
• 30A1 wide slot nozzle 2OMM
• 1 Pair of carbon brushes I 20V
• Element 120V 1600W
• Air filter
• Tool box for Triac kit
• Brass nozzle cleaning brush
• Filter brush
• 4Omm hand roller
(800) 486-1832 www.trianglefastener.com
74

DOW
INSTA-STIK ROOF INSULATION ADHESIVE
INSTA-STIK
Insta-Stik professional roof adhesive is a single component
polyurethane adhesive dispensed from a portable, disposable
pre-pressurized container requiring no external power source.
Insta-Stik is used to attached compatible roof insulation
boards to roof decks and substrates in new construction and
roof replacement applications. This includes insulation board
to insulation board, insulation board to Class 1 non-graveled
(bald) build-up roofs for re-cover applications and insulation
or gypsum board to 22 gauge and thicker steel decks and
wood decks.
Wood Deck:
Insta-Stik works on wood decks whenever metal fasteners are
not desired. The insulation is securely held without damaging
the structural integrity of the wood deck. When the underside
of the deck is visible, there are no unsightly fasteners points
sticking through.
Concrete Deck:
Roof top productivity is greatly increased by using Insta-Stik.
No tedious and noisy predrilling required. Compatible with
EPS (expanded polystyrene) insulation and wood fiber board,
Insta-Stik gives you the ability to choose the right insulation
type for the job.
Metal Deck:
Insta-Stik is the smart choice when it comes to metal decks.
when the project demands that no fasteners penetrate the
deck due to electrical conduits, exposed underside of deck,
thermal bridging concerns, or environmental conditions, then
Insta-Stik is your proven fastener.
NON-COMPATIBLE APPLICATIONS
Non-compatible Roof Insulation Boards:
• Extruded polystyrene
• Fiberglass
Non-compatible Substrates:
• Coal tar pitch built-up roofs
• Lightweight insulating concrete
• Active asphalt
PROFESSIONAL
ROOF INSULATION
ADHESIVE
COMPOSITION & MATERIALS
Insta-Stik Professional Roofing Adhesive is a single component,
moisture cured polyurethane adhesive. Insta-Stik is free of
conventional solvents. Insta-Stik Complete is supplied in a 30 Lb
(14 kg) unit, 23 Lb (10 kg) net chemical weight, with a 4’ (1 m)
flexible dispensing hose and two 14” (356 mm) PVC dispensing
wands, with coupler. A brass ball valve at the end of the
dispensing hose allows operational control for single-hand
application. Insta-Stik Tank Only is supplied in a 30 Lb (14 kg)
unit, 23 Lb (10 kg) net chemical weight, with no dispensing
equipment. The tank only is ideal for use with the Multi-Bead
Applicator.
Accessories:
The dispensing of Insta-Stik can be dramatically increased using
the Multi-Bead Applicator (MBA-28) and Day Pak System
(DPS-4) accessory kits. The MBA-28 dispenses 4 equidistant
beads of Insta-Stik within a 4’ (1 m) wide path. Each MBA-28 is
supplied with 2 Day Pak Systems. The DPS-4 is the dispensing
tubing for the MBA-28. The DPS-4 must be replaced daily or
whenever cured Insta-Stik blocks or restricts flow within the
tubing. The use of the MBA-28 is recommended on roof decks
with few penetrations and obstructions.
Limitations
• Insta-Stik is not recommended for use with
insulation boards larger than 4’ X 4’ (1 m X 1 m).
• Insta-Stik is not recommended for residential
roofing applications.
• Insta-Stik is not recommended for application when
surface or ambient temperatures are below 40º F
(4º C) or above 110º F (43º C).
• Insta-Stik is not recommended for use during
inclement weather.
• Insta-Stik is not recommended for use on wet surfaces.
• Insta-Stik is not recommended for use on gravel,
excessively dirty, or grease-laden surfaces.
• Insta-Stik is not approved for use if the product
has expired.
• Insta-Stik is not recommended for use on roof decks
greater than 2:12 slope. For higher slopes, contact
Technical Support.
• Insta-Stik is not recommended for use in attaching
base sheets and membranes.
Flexible Products Company accepts no responsibility for
judging the acceptability of the roof substrate or for the
roof systems structural integrity.
75
TRIANGLE FASTENER CORPORATION

DOW
INSTA-STIK ROOF INSULATION ADHESIVE
Technical Data
APPROVALS
Factory Mutual (FM):
Insta-Stik professional Roofing Adhesive meets the requirements of the following
FM fire and wind uplift resistance tests for FM approved roof deck applications:
FLAT
• Class 1-60 • Class 1-150 • Class 1-195 • Class 1-240
• Class 1-90 • Class 1-165 • Class 1-210 • Class 1-270
• Class 1-135 • Class 1-180 • Class 1-225
TAPERED
• Class 1-135 • Class 1-165 • Class 1-195 • Class 1-315
• Class 1-150 • Class 1-180 • Class 1-240
Insta-Stik has the only industry adhesive approval on tapered systems. Please consult with
Technical Support or Flexible Products’ listing in the latest Factory Mutual Approval Guide
for details.
INSTA-STIK HANDLING CHARACTERISTICS
Temperatures
Tackfree Time
40º F (4º C), 50% RH 35 minutes
75º F (24º C), 50% RH 15 minutes
120º F (49º C), 25% RH 13 minutes
Dade County (Florida)
Insta-Stik Professional Roofing Adhesive meets the requirements of Metropolitan
Dade County, Florida, windstorm and fire classifications for roof deck applications.
Insta-Stik is packaged in a single container that should be stored between 45º F (7º C) and
75º F (24º C). At these temperatures, the shelf life is 8 months from date of manufacture.
The minimum product temperature at the time of application should be 70º F (21º C). The
minimum ambient and surface temperatures must be 40º F (4º C).
INSTA-STIK APPLICATION RATES 1
BASED ON 3/4”-1”(19.1-25.4 MM) DIAMETER BEAD
Building Height Parapet Perimeter Perimeter Field
Ft (m) Wall Height Band Width Application Application
In (mm) Ft (m) Rate In (mm) OC Rate In (mm) OC
0-20 (0-6) 0-24 (0-610) 3 (0.9) 6 (152) 12 (305)
25+ (635+) 0 12 (305) 12 (305)
21-40 (6-12) 0-24 (0-610) 6 (2) 6 (152) 12 (305)
25-48 (635-1219) 3 (0.9) 6 (152) 12 (305)
49+ (1245+) 0 12 (305) 12 (305)
41-70 (13-21) 0-24 (0-610) 9 (3) 6 (152) 12 (305)
25-48 (635-1219) 6 (2) 6 (152) 12 (305)
49+ (1245+) 3 (0.9) 6 (152) 12 (305)
71-100 (22-31) 0-24 (0-610) 12 (4) 6 (152) 9 (229)
25-48 (635-1219) 9 (3) 6 (152) 12 (305)
49+ (1245+) 9 (3) 6 (152) 12 (305)
101-200 (31-61) 0-24 (0-610) 12 (4) 6 (152) 9 (229)
25-48 (635-1219) 12 (4) 6 (152) 9 (229)
49+ (1245+) 12 (4) 6 (152) 12 (305)
201-300 (61-91.5) 0-48 (0-1219) 12 (4) 6 (152) 9 (229)
49+ (1245+) 12 (4) 6 (152) 9 (229)
301+ (91.8+) -- 0 6 (152) 6 (152)
1
Coverage is approximately 500-800 ft 2 (47-74m 2 ) per 23 lb (10 kg) tank of Insta-Stik depending
on bead size.
PHYSICAL PROPERTIES OF INSTA-STIK ROOFING ADHESIVE
Tensile Adhesion Lap Shear Adhesion Lap Shear Adhesion Peel Adhesion
Concrete/Concrete Carbon Steel/Carbon Steel Galvanized Steel/Galvanized Steel To Concrete
259 psi (1785 kPa) 342 psi (2356 kPa) 328 psi (2262 kPa) 18 lbf (80 N)
Note: Samples cured for 7 days at 75º F (24º C) 50% RH.
(800) 486-1832 www.trianglefastener.com 76

DOW FOAM INSULATING SEALANTS
PRODUCT DESCRIPTION
Froth-Pak is a self contained, portable two-component polyurethane
foam dispensing system that requires no outside power source and is
disposable when empty (consult local authorities for proper disposal).
All Froth-Pak materials have been formulated utilizing either HCFCs or
HFCs rather than traditional CFCs. HCFCs are 20 times less
hazardous to the environment or the earths ozone layer than CFCs.
Froth-Pak kits are available in a variety of densities in convenient,
factory pressurized dispensers sized to facilitate any installation (see
Size Table). Kits are supplied complete with gun-hose assembly and
standard spray (NS) nozzles. Special purpose nozzles are available as
optional extra (see Accessories Table).
FROTH-PAK ACCESSORIES
Item
5-1/2 ft. gun hose assembly
7-1/2 ft. gun hose assembly
7-1/2 ft. gun hose assembly with nozzles
15 ft. gun hose assembly
15 ft. gun hose assembly with nozzles
Insta-Flo 12 Dispenser (Refill Kits)
FROTH-PAK
TWO-COMPONENT
SPRAY
POLYURETHANE
FOAM SYSTEM
TYPICAL PHYSICAL PROPERTIES*
ASTM Result
Property Test Method 1.75 pcf HCFC
Flexural Strength C-203
Parallel, psi 23.0
Perpendicular, psi 42.6
Apparent K Factor (BTU•in)/(ft2•hr•ºF) Initial C-518 0.143
Aged 6 months 0.187
Aged 12 months 0.196
Aged 18 months 0.204
Aged 24 months 0.208
Apparent R Value @ 1” (derived from K Factor) ---
Initial 7.0
18 months 4.9
Accelerated Service Conditions Procedure “A” D-756
% Volume Change 2.97
% Weight Change -1.75
Procedure “B”
% Volume Change 1.05
% Weight Change -2.19
Procedure “E”
% Volume Change 9.91
% Weight Change -2.84
Compressive Strength D-1621
Parallel, psi 22.0
Perpendicular, psi 8.4
Apparent Density, pcf D-1622 1.70
Water Absorption (% water base) D-2842 2.5
Dimensional Stability (% volume change) D-2126
100º F/100% RH, 1 week 0.38
100º F/100% RH, 2 weeks 0.91
158º F/100% RH, 1 week 15.57
158º F/100% RH, 2 weeks 14.02
-40º F/amb RH, 1 week -0.40
-40º F/amb RH, 2 weeks -0.04
-100º F/amb RH, 1 week -3.70
-100º F/amb RH, 2 weeks -1.13
158º F/amb RH, 1 week 3.70
158º F/amb RH, 2 weeks 3.65
212º F/amb RH, 1 week 1.48
212º F/amb RH, 2 weeks 1.16
Open Cell Content D-2856

DOW FOAM INSULATING SEALANTS
Technical Data
Froth-Pak 1.75-25FS MSHA conforms to building code requirements for a Class 1 foam. When tested to ASTM E-84,
the flame spread is 25 and the smoke developed is 350 at 2” (50 mm) thickness with full coverage.
Froth-Pak 1.75-25FS MSHA also conforms to Mine Safety and Health Administration (MSHA)
surface flame spread requirement ASTM E-162 (flame spread index of 25 or less).
These tests do not purport to address all of the safety problems, if any, associated with it’s use.
Warning:
The foam produced by Froth-Pak is organic and is combustible and may constitute a fire hazard if improperly used.
Installation
For best results, remove any lose debris, dirt, dust or other deleterious material from surfaces.
Also, best results are obtained when chemical temperatures are 75º F (24º C).
Every Froth-Pak kit is self-contained and ready to use. Kits are factory pressurized and require no outside power source.
With it’s convenient dispensing design, Froth-Pak simplifies set-up and use. Typically, a Froth-Pak kit consists of one
”A” and one “B” cylinder in one carton plus a hose assembly and accessories.
Application
Every purchase of a Froth-Pak kit includes “Operating Instructions”. A Material Safety Data Sheet is available upon
request. Read all information and cautions before using Froth-Pak. “Operating Instructions” include information on
operation, trouble shooting, yield, application tips, quality control, curing, storage, disposal, first aid, and similar
information.
Precautions
Avoid contact with eyes and skin. ALWAYS wear protective eyewear, gloves, and clothing when operating.
Use ONLY with adequate ventilation or NIOSH-certified respiratory protection.
In unventilated areas, DO NOT remove respirator for AT LEAST 15 MINUTES after use.
CONTENTS UNDER PRESSURE. To avoid possible explosion or fire, DO NOT puncture or incinerate.
DO NOT refill or repressurize. DO NOT expose cylinders to temperatures above 120º F (49º C).
The foam produced is combustible. DO NOT expose to heat, sparks or open flame.
This product is NOT intended for use in applications where temperatures exceed 250º F (121º C).
Store at temperatures between 60º F and 80º F (16º C and 27º C).
(800) 486-1832 www.trianglefastener.com 78

DOW TILE BOND ® TILE BOND ®
THE PREFERRED ADHESIVE FOR
ROOF TILE INSTALLATION
FAST, TROUBLE-FREE, LIGHTWEIGHT,
CONVENIENT,
AND HURRICANE-PROVEN
PRODUCT DESCRIPTION/APPLICATION
Tile Bond® is a polyurethane adhesive used for adhering roofing tile to
approved commercial or residential roof deck underlayments. This portable,
disposable one component polyurethane adhesive provides superior
attachment strength over other methods and can be used for new, reroof
and tile roof repair applications. It reduces tile breakage and material costs
while eliminating the need to purchase, transport and maintain heavy
equipment.
Tile Bond makes installing and repairing residential or commercial tile roofs
quick and easy, reducing labor costs and eliminating nailing on roofs with
pitches up to 6:12. The 23 lb (10 kg) canister will adhere approximately 750
field tiles. The 20 oz (568 g) can will adhere approximately 40 field tiles.
SIZES
Tile Bond is available in a 23 lb (10 kg) canister complete kit which includes a
dispenser with hose, 9/16” (14.3 mm) wrench, foam backer rod to illustrate
proper patty size, and an instruction sheet. It is also available in a convenient
20 oz (568 g) can for quick and easy use.
Approvals:
• UL Class 1 listed (ASTM E84)
• Class A rated (ASTM E108)
• South Florida Building Code, Broward County, 1999 Edition
• Metro-Dade County Acceptance #99-0412.04 (Expires 10/01/01)
• SBCCI Evaluation Report #9744A (Refer to this evaluation report
for code compliance.)
Installation:
Tile bond will adhere to the following roof tile types:
• 2 piece barrel profile
• High profile
• Medium profile
• Low/flat profile
79
TRIANGLE FASTENER CORPORATION

PULLOUT TESTING
We will go to the job and perform
pullout tests to assist you in
determining the proper fastener
(800) 486-1832 www.trianglefastener.com 80

SIMPLEX
ROOFING NAILS
REGULAR
ROUND HEAD
Ring or Smooth
Shank
SIZES AND QUANTITIES
Fastening Required Required
Shank Range Deck
Shank Gage Max. Total Penetration Deck Pieces/
# Length Thickness Plywood Wood Penetration Pounds
1 1/2” 12 1/16” The 1/2” 109
2 5/8” 12 1/16” nail 5/8” 106
3 3/4” 12 1/16” must 3/4” 102
4 7/8” 12 1/16” pass 7/8” 99
5 1” 12 1/16” through 1” 96
6 1 1/4” 12 1/4” the 1” 91
7 1 1/2” 11 1/2” plywood 1” 78
8 1 3/4” 11 3/4” by a 1” 73
9 2” 11 1” 1/4” 1” 69
10 2 1/2” 11 1 1/2” 1” 62
11 3” 11 2” 1” 56
DESIGN OPTIONS
Shank Types Coating Types Container Types Cap Diameter Nail Materials
Annular Grooved Bright 25 Lbs. Boxes 1” Hi-Carbon Steel
Smooth Yellow Di-chromate 50 Lbs. Boxes
Electro Galvanized
Hot Dipped Galvanized Pails
Rust-Lok ®
Insulation Round Head
Ring or Smooth Shank
SIZES AND QUANTITIES
Pieces
Nail Shank Head Per
Length Size Diameter Pound
3” 9 ga. 1” 44
3 1/2” 9 ga. 1” 39
4” 9 ga. 1” 36
5” 9 ga. 1” 31
6” 8 ga. 1” 27
7” 8 ga. 1” 24
8” 8 ga. 1” 20
Uses: BUR applications and other applications where thick insulation's are attached to wood substrates. Available
in ring shank or smooth shank.
3/4” 9 ga. 1” 84
MASONRY ROUND HEAD
1” 9 ga. 1” 76
Fluted Shank
1 1/4” 9 ga. 1” 64
1 3/4” 9 ga. 1” 70
1 1/2” 9ga. 1” 59
2”- 6” 9 ga. 1”
PLEX-CAP ®
PLASTIC CAP NAILS
Ring Shank
3/4” 12 1/2 ga. 1” 352
7/8” 12 1/2 ga. 1” 318
1” 12 1/2 ga. 1” 298
1 1/4” 12 1/2 ga. 1” 274
1 1/2” 12 1/2 ga. 1” 170
1 3/4” 12 1/2 ga. 1” 149
2” 12 ga. 1” 132
2 1/2” 12 ga. 1” 110
3” 12 ga. 1” 94
Uses: For fastening applications of roofing felt, insulation, hose wraps, & polyfilm. Manufactured from high
strength polymer plastic.
SQUARE CAP NAIL 3/4” 12 ga. 1” 63
7/8” 12 ga. 1” 62
1” 12 ga. 1” 61
1 1/4” 12 ga. 1” 58
1 1/2” 12 ga. 1” 56
1 3/4” 12 ga. 1” 54
81
TRIANGLE FASTENER CORPORATION

SIMPLEX
ROOFING NAILS AND FASTENERS
SIZES AND QUANTITIES
TUBE-LOK ®
FASTENERS
Patented
Fastening
Range Required
Shank Shank Max. Total Deck Pieces / Pieces / Pounds /
# Length Gage Thickness Penetration Pounds Box Box
1 1” 0.108 0” 1” 78 2,500 40
2 1 3/4” 0.108 1/4” 1.5” 66 2,500 52
3 2 1/2” 0.108 1” 1.5” 56 2,500 62
4 3” 0.108 1 1/2” 1.5” 51 2,500 63
5 3 1/2” 0.108 2” 1.5” 46 2,500 70
6 4 1/2” 0.108 3” 1.5” 39 1,000 36
7 5 1/2” 0.108 4” 1.5” 34 1,000 40
8 6 1/2” 0.108 5” 1.5” 30 1,000 45
DESIGN OPTIONS
Shank Types Coating Types Container Types Cap Diameter Nail Materials
Annular Grooved Bright 25 Lbs. Boxes 1” Hi-Carbon Steel
Smooth Yellow Dichromate 50 Lbs. Boxes
Electro Galvanized
Hot Dipped Galvanized Pails
Rust-Lok ®
BASE-LOK ®
Patented
Uses: The Simplex Base-Lok® is used to secure base
sheet to aggregate lightweight concrete, cellular
lightweight concrete decks. Easy to install one piece
fastener manufactured from engineered plastic.
ASSEMBLED
TUBE-LOK ®
Uses: Effective attachment of roofing products to low and
steep slope decks fabricated from Gypsum, cellular and
aggregate lightweight concrete, cementitious wood fiber and
other lightweight deck assemblies. Assembled for faster
installation. New Simplex Installation Tool.
New Item
Pieces
SIZES AND QUANTITIES
Nail Length: 1 3/4” Carton contains 1000 pieces.
* Approximate count.
SIZES AND QUANTITIES
Nail Tube Head Per
Length Diameter Diameter Pound
1 3 /4” .197” 2” 25
THE SIMPLEX ROOFING FASTENER SELECTION TABLE
Simplex #2 Simplex #3 Standard Building Codes
Rupture Rupture Term Rust-Lok® and Standard Simplex
# Substrate Roofing Material Fastener Plate Plate Bars Coating Approvals Brand Tools
1 Wood Deck 15 lbs. & 30 lbs. Felt Plastic Cap Nails • None Pole-Tap ® or Hand Tap ®
“Original” Metal 1” Cap Nails • • • APA & FFN-105B Pole-Tap ® or Hand Tap ®
“Original” Metal 2” Cap Nails • APA & FFN-105B Pole-Tap ® or Hand Tap ®
Base Sheet “Original” Metal 1” Cap Nails • • • APA & FFN-105B Pole-Tap ® or Hand Tap ®
“Original” Metal 2” Cap Nails • APA & FFN-105B Pole-Tap ® or Hand Tap ®
Insulation Insulation Metal Cap Nails • • • APA & FFN-105B Pole-Tap ® or Hand Tap ®
Recover Board over Old Roof Insulation Metal Cap Nails • • • APA & FFN-105B Pole-Tap ® or Hand Tap ®
2 Gypsum Deck Base Sheet “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
“Assembled” Tube-Lok® 2” Nails Pending Tube-Tap ®
Base-Lok® Fasteners Dade & FM Drill-Tap ® , Extend Zip ® or Base-Zip ®
Insulation “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Ta
Recover Board over Old Roof “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
3 Light Weight Base Sheet “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
Concrete “Assembled” Tube-Lok® 2” Nails Pending Tube-Tap ®
Deck Base-Lok® Fasteners Dade & FM Drill-Tap ® , Extend Zip ® or Base-Zip ®
Insulation “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
Recover Board over Old Roof “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
4 Tectum Deck Base Sheet “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
“Assembled” Tube-Lok® 2” Nails • • • Dade Pole-Tap ® or Hand Tap ®
Base-Lok® Fasteners Dade & FM Drill-Tap ® , Extend Zip ® or Base-Zip ®
Insulation “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
Recover Board over Old Roof “Original” Tube-Lok® 1” Cap Nails • • • Dade Pole-Tap ® or Hand Tap ®
5 Masonry Wall Base Flashing Masonry Cap Nails • • • None None
Zanchor® Zinc Hammer Drive Nails • • • None None
6 Wood Wall Base Flashing “Original” Metal 1” Cap Nails • • • APA & FFN-105B Hand Tap ®
“Original” Metal 2” Cap Nails • APA & FFN-105B Hand Tap ®
7 Gypsum Wallboard Base Flashing Wall-Lok® Zinc Drywall Anchors • None None
(800) 486-1832 www.trianglefastener.com
82

TRACER ® DRYWALL FASTENERS - Wood or metal
TRACER ® Flat Bugle Head
Attachment of drywall to steel stud up to 20 gauge
(.036”).
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
6 x 1” 3/8” - 5/8” 10
6 x 1 1/8” 3/8” - 3/4” 10
6 x 1 1/4” 3/8” - 7/8” 8
6 x 1 5/8” 3/8” - 1 1/4” 5
6 x 2” 1” - 1 5/8” 3.5
6 x 2 1/4” 5/8” - 1-7/8” 3
7 x 2 1/2” 7/8” - 2 1/8” 2.5
8 x 3” 1 3/8” - 2 5/8” 2
10 x 3 1/2” 1
10 x 4” 1
10 x 4 1/2” 1
10 x 5” .5
10 x 6” .5
Phos and oil
TRACER ® COARSE TYPE “W”
Attachment of drywall to wood stud or framing.
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
6 x 1” 3/8” - 5/8” 10
6 x 1 1/8” 3/8” - 3/4” 10
6 x 1 1/4” 3/8” - 7/8” 8
6 x 1 5/8” 3/8” - 1 1/4” 5
6 x 2” 1” - 1 5/8” 3.5
6 x 2 1/4” 5/8” - 1 7/8” 3
7 x 2 1/2” 7/8” - 2 1/8” 2.5
8 x 3” 1 3/8” - 2 5/8” 2
10 x 3 3/4” 2
10 x 4” 1
10 x 4 1/2” 1
10 x 5” .5
10 x 6” .5
Phos and oil
HI-LO ® SHARP POINT
Attachment of drywall to steel stud up to 20 gauge
(.036).
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
7 x 1” 3/8” - 5/8” 10
7 x 1 1/8” 3/8” - 3/4” 8
7 x 1 1/4” 3/8” - 7/8” 8
8 x 1 5/8” 1/2” - 1 1/4” 5
8 x 1 7/8” 3/4” - 1 1/2” 4
8 x 2 1/4” 1 1/16” - 1 7/8” 2.5
8 x 2 5/8” 1 3/8” - 2 1/4” 2.5
8 x 3” 1 7/8” - 2 5/8” 2
Need additional corrosion
protection?
Now available with our TRI-ACQ TM coating
for treated lumber applications!
Size: #6 x 1-1/4” GP Coarse thread. Phillips
bugle head.
1,000 hrs salt spray
TRACER ® TRIM HEAD
Attachment of drywall to steel stud up to 20 gauge
(.036”).
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
6 x 1 5/8” 1/2” - 1 1/4” 5
6 x 2 1/4” 5/8” - 1 7/8” 3
6 x 3” 3/4” - 2 5/8” 2
TRACER ® TYPE “G”
Attachment or lamination of layered drywall.
Phos and oil
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
10 x 1 1/2” 3/4” - 1” 5
Phos and oil
TRACER ® PAN HEAD
Attachment of steel stud to steel track or for splicing
steel stud up to 20 gauge (.036”) total thickness.
Carton
Size/Length Quantity (M)
7 x 7/16” 10
Phos and oil
83
TRIANGLE FASTENER CORPORATION

TRACER ® DRYWALL FASTENERS - Metal
TRACER ® D.S. BUGLE HEAD
Attachment of drywall to steel stud up to 14 gauge
(.075).
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
6 x 1” 3/8” - 5/8” 10
6 x 1 1/8” 3/8” - 3/4” 10
6 x 1 1/4” 3/8” - 7/8” 8
6 x 1 5/8” 3/8” - 1 1/4” 5
6 x 1 7/8” 3/8” - 1 1/2” 4
6 x 2” 3/8” - 1 5/8” 4
6 x 2 3/8” 3/8” - 2” 2.5
6 x 2 5/8” 3/8” - 2 1/4” 1.6
6 x 3” 3/8” - 2 5/8” 1.4
TRACER ® D.S. TRIM HEAD
Attachment of wood trim thru drywall to steel stud up
to 14 gauge (.075).
Drywall Thickness Carton
Size/Length Minimum-Maximum Quantity (M)
6 x 1 5/8” 1/2” - 1 1/4” 5
6 x 2 1/4” 5/8” - 1 7/8” 3
Zinc plated
Zinc plated
Need additional corrosion
protection?
Now available with our TRI-ACQ coating for
treated lumber applications!
TRACER ® CB Cement Board
Attachment into wood or metal up to 18 gauge.
Size/Length
8 x 1 1/4”
8 1 5/8”
8 x 2-1 /4”
Long life coated
Size: #6 x 1-1/4” DP2. Phillips bugle head.
1,000 hrs salt spray
Performance Characteristics
TRACER DRYWALL FASTENING SYSTEMS
Torsional Shear
Tensile Strength Strength Strength
Product Thread Thread Dia. Root Dia. Root Area Ultimate Stress Tensile Ultimate Ultimate
Type DIA. Per Inch (Nom.) (max.) (Sq.In.) (LBs.) (P.S.I) (Inch Lbs.) (Lbs.)
Tracer Coarse 6 10 .151 .092 .0082 1422 173,414 41 938
Tracer Fine 6 18 .139 .092 .0066 1322 200,303 44 1015
Tracer DS 6 20 .142 .105 .0086 1500 174,418 43 775
Tracer Coarse 7 9 .164 .102 .0082 1430 192,195 40 773
Tracer Fine 7 16 .155 .107 .0089 1576 177,078 46 1238
7 19 .153 .095 .0070 1398 199,714 42 880
Tracer Coarse 8 9 .177 .110 .0094 1540 163,829 53 902
Tracer Fine 8 15 .165 .116 .0105 1802 171,619 67 1387
Tracer Hi-Lo 8 18 .167 .100 .0078 1430 183,333 48 925
Pullout Strength (LBS.ULT.)
Steel Gauge
Fastener Description 26 24 22 20 18 16 14
7-19 Tracer Hi-Lo 129 178 244 277
8-18 Tracer Hi-Lo 163 242 314 370
6-18 Tracer Fine 122 168 228 288
7-16 Tracer Fine 142 199 265 302
8-15 Tracer Fine 134 235 289 351
6-20 Tracer D.S. 120 183 248 296 471 679 847
Pullout Strength (LBS.ULT.)
Embedment in 2x4 Stud Grade S.Y.Pine
Fastener Description 1/2” 3/4” 1” 1-1/4”
6-10 Tracer Coarse 182 328 422 620
6-18 Tracer Fine 160 290 400 586
7-9 Tracer Coarse 189 318 440 630
7-16 Tracer Fine 172 288 408 590
8-9 Tracer Coarse 186 290 502 645
8-15 Tracer Fine 179 278 490 651
The values listed are ultimate averages achieved under laboratory conditions. An appropriate safety factor must be applied to these values by the user to achieve a
design load.
(800) 486-1832 www.trianglefastener.com
84

TRAKFAST
The automatic fastening system designed for speed,
durability and ease of use
SPEED Three to five times faster than powder tools. 42-pin magazine reduces loading
time.
EASY TO USE Tool automatically resets piston. No recoil, tool absorbs shock resulting
in less operator fatigue.
NO LICENSING REQUIRED Unlike powder-actuated tools, no licensing is needed.
NO CHANGING LOADS TrakFast uses a fuel cell, not a load. No need to inventory
different colored loads.
NARROW NOSE AND PROFILE Allows tool to reach inside deep leg track (1-5/8" wide
x 2" high).
2 Year Warranty (6 months on wearable parts).
Part No. TF1100
Maximum Capacity: 42 pins
Maximum cycles/second: 2
Fuel cell: 1000 shots
Battery (charged): 3000 shots
T2
Fully Automatic
25% More Power
Fuel Injection
• Fuel injection—means no additional step of
clicking a metering valve to the top of the fuel cell
• T2 raises the bar for high-volume gas powered
fastening
• 40-pin magazine
• For hard concrete and steel
• Perfect for overhead runs
• 25% more power than TrakFast
• No licensing required
• 2 Year Warranty (6 months on wearable parts).
• Maximum Capacity: 43 pins
• Fuel cell: 1000 shots
• Battery (charged): 1200 shots
T3SS
Single Pin Gas Tool
Fuel Injection
Cross Over Technology
• Sets the standard for single-shot applications
• 5 times faster than traditional drill and anchor
methods
• Replaces the need for tools like the DX35
• Reduced operator fatigue
• Reduced installation costs—up to 75%
• Quiet enough to work in tenant occupied buildings
• Removable rear foot
• 2 Year Warranty (6 months on wearable parts).
• Pin Guide O.D.: 1/2" Standard, 7/8" Magnetic
• Pin Capacity: 1-1/2"
85
TRIANGLE FASTENER CORPORATION

TRAKFAST
PULLOUT LOADS
(800) 486-1832 www.trianglefastener.com
86

STEEL FRAMING FASTENERS
TRACER ® D.S. PAN FRAMER
Attachment of steel stud of steel track or for splicing
steel stud up to 14 gauge (.075”) total thickness.
Carton
Size/Length Quantity (M)
6 x 7/16” 10
8 x 1/2” 10
8 x 1” 10
.00015” zinc plated zinc plated
TRACER ® D.S. ROUND WASHER HEAD
Attachment of wood trim thru drywall to steel stud up to 14
gauge (.075”).
Carton
Size/Length Quantity (M)
8 x 1/2” 10
8 x 3/4” 5
8 x 1 1/4” 10
.00015” zinc plated zinc plated
BLAZER PAN HEAD
Fastener for steel framing applications.
Size/Length Head Type
8-16 x 5/8” DP2 Phillips pan
.00015” zinc plated zinc plated
BLAZER LO PROFILE PANCAKE
HEAD
Fastener for steel framing applications.
Size/Length
Head Type
10-16 x 5/8” DP3 #2 square recess
pancake
.0003” zinc and yellow
BLAZER LO PROFILE HIGH
TORQ PANCAKE HEAD #2 SQ.
Fastener for steel framing applications.
Size/Length
.0003” zinc and yellow
Head Type
10-24 x 5/8” DP3 #2 Sq.Phil recess
high torq
pancake
BLAZER HI-HEX
Fastener for steel framing applications.
With serration.
Size/Length
.0003” zinc plated
Head Type
10-16 x 5/8” DP3 5/16” Hi-Hex
10-16 x 3/4” DP3 design
BLAZER HEAVY GAUGE
Fastener for steel framing applications.
Size/Length Head Type
12-24 x 1 1/4” DP5 5/16” HWH
heavy gauge up to 1/2”
.0003” zinc plated with long life coating.
BLAZER PILOT
Long pilot section allows the fastener
to complete the drilling before tapping
occurs, eliminating drill point failures.
Size/Length
Head Type
12-14 x 7/8” DP3 5/16” Hex
washer head
Finish: .0003” min. electro zinc plated with flouropolymer topcoat.
Corrosion results: 1,000 hrs. salt spray
Applications: Drilling and tapping up to .210” thick steel.
STRESS-LESS FRAMING
SCREW
Fastener for steel framing applications with high
stress concentrations. Drill and tap uo to 1/4” steel!
For technical data, refer to page 12.
Size/Length Head Type
1/4-14 x 7/8” DP3 5/16” Hex
washer head
Epoxy Coated
87
TRIANGLE FASTENER CORPORATION

TWISTER PRE-TIED WIRES
IT’S TIME TO GET TWISTED!
Are you looking for complete selection of standard and custom pre-tied wires? Triangle
Fastener is the source!
We offer a full line of pre-tied wires for fastening into metal, wood, or concrete. Our fasteners,
clips, and tools assure a positive connection and easy installation.
With our in-house production, we produce high quality ties and quick delivery.
•Pin and clip combos
•Angle clips
IN STOCK FOR IMMEDIATE SHIPMENT!
•Angle clips with self-drillers •Acoustical toggle bolts
•Angle clips with Tapcons •Acoustical eye lags
•2-1/2” timber pin and clips
•Caddy Clips
WE CAN ASSEMBLE AND TIE THE WIRE TO A SPECIFIC FASTENER
FASTENERS AND CLIPS
PIN AND CLIP
For metal wood or
concrete applications
*Concrete pins
*Stepdown steel pins
*2-1/2” Timber pins
SELF-DRILLING
Use in steel deck
applications
1/4 x 2”
1/4 x 2-3/4”
LAG
Use in wood
applications
1/4” x 3”
1/4” x 4”
1/4” x 5”
WEDGE ANCHOR
Use in concrete
applications
Contact TFC for a size to
meet your specific
requirement
TOGGLE
Supplied with nut,
washer, and toggle
1/4-20 x 4”
1/4-20 x 5”
TAPCON
Use in concrete
applications
3/16” x 1-1/4” & 1-3/4”
1/4” x 1-1/4” & 1-3/4”
HWH
BLAZER SELF-DRILLING
Use in metal
applications up to 1/2” thick
#10 x 3/4” DP3
#12-14 x 1” DP3
#12-24 x 7/8” DP4
#12-24 x 1-1/4” DP5
CHOOSE A WIRE FROM OUR STANDARD LENGTHS
Wire size and load capacity
12 gauge (.105”) ..... Ultimate weight capacity of 600 lbs.
* 9 gauge (.147”) ..... Ultimate weight capacity of 1,190 lbs.
Wire lengths (Custom lengths available)
4 foot - 6 foot - 8 foot - 12 foot - *16 foot
* Available upon request
STRUCTURAL CLIPS
Clip-Pur
Z-purlin applications
J-Clip
Open web bar joist applications
(1/16” to 1/4” flange)
J-Master Tool for installing
Clip-Pur and J-Clip
Clip-Pur and J-Clip are tradenames of ITW Ramset
(800) 486-1832 www.trianglefastener.com
88

PURLIN AND BAR JOIST CLIPS
J-MASTER TOOL ® -L1700
For attachment of J-Clip® (L1701) and Clip-Pur® (L1801) Hanger Wire Clips.
CLIPS USED WITH THE J-MASTER TOOL®
(L1701)
J-CLIP ®
• Strong, reliable attachment of
pre-tied hanger wire.
• Use for open web bar joists or
purlins.
• Each clip fits 1/16”-1/4” flanges.
(L1801)
CLIP-PUR ®
• Fast, easy attachment of pre-tied
hanger wire from Z-Purlins.
• Disengages from J-Master tool
after installation.
• Two magnetic strips attached to
J-Master tool make installation
easy.
EASY INSTALLATION
1. Attach a 1/2” pipe extension (dielectric pole available) to
the threaded end of a J-Master tool, and place pre-wired J-
Clip into tool.
2. Insert the J-Clip up into the void between the two base
angles. Position the clips over the vertical flange and pull
down.
3. Disengage the tool by lifting up and out.
1. Attach J-Master tool to end of threaded 1/2” pipe or
dielectric pole. Lay pre-tied Clip-Pur against magnetized
strips.
2. Raise the Clip-Pur up to the purlin. Position the clip on the
45° flange and give a downward tug, the clip is now in
position.
3. Disengage the tool by lifting up and out.
J-Clip attached to the
J-Master Tool
Clip-Pur attached to the
J-Master Tool
89
TRIANGLE FASTENER CORPORATION

OVERHEAD POWDER ACTUATED FASTENING
Use with Twister Pre-Tied Wire!
EXTENSION POLES
Quality Ramset extension poles provide the convenience of using powder actuated tools
for overhead fastening without the need for scaffolding or ladders.
Can be used with various
Ramset actuated tools
PART NUMBERS FOR RAMSET TOOLS
PTSEMI6 (6’) and PTSEMI8 (8’) for use with:
D60—our premier semi-automatic tool, featuring power level adjustment
and no-waste disc loads.
SA270—high-quality .27 caliber strip tool for general purpose applications.
D45A—most durable, high-power, semi-automatic tool for hard concrete
and steel applications.
MD380—popular 3/8” head diameter tool.
721 The industry preferred tool for the drywall trade.
PTSEMI6 (6’) and PTSEMI8 (8’) for use with:
Cobra
VIPER
Fixed-length Telescoping extension poles
extension poles adjustable in 1 foot increments
6’ #VPOL6 6’-12’ #TVPOL612
8’ #VPOL8 6’-18’ #TVPOL618
APPLICATIONS
Ramset Pole Tools are
an excellent choice for
high-reach fastening
applications.
Fast, easy installation from floor
level eliminates lift baskets,
scaffolds and ladders.
Rubber “motorcycle”
grip for operator
comfort and to
reduce recoil level
Top-quality hand lever
and cable system
requires only 15 pounds
of pressure so cable
doesn’t stretch
Encased cable
runs length of
pole and
connects hand
lever with
trigger—no rods
to bend inside
Tefloncoated
cable reduces
drag and less
wear on user’s
hand
Delrin coupler
on cable makes
pole di-electric
Nyloc nuts
keep your
adjustment
fixed solidly on
the trigger bar
Lightweight cast
aluminum
housing fits tool
snugly and
provides tool
protection
Trigger bar adjusts
easily for individual
tools
(800) 486-1832 www.trianglefastener.com
90

LAGMASTER PLUS
Use with Twister Pre-Tied Wire!
LAGMASTER PLUS is the electrician’s pole tool. The unique plug-in heads make it the most
efficient tool of its kind. It increases safety by keeping your men on the floor. Use it to install ceiling wire, jack
chain, threaded rod, smooth rod and overhead screw installation. Power the pole with any 3/8” or 1/2”
battery operated or corded drill.
One pole - many applications!
CHOOSE FROM FIVE DIFFERENT ADJUSTABLE LENGTH MODELS:
• LM-6 Double 3’ (11’ ceilings) • LM-18 Triple 6’ (24’ ceilings)
• LM-12 Double 6’ (18’ ceilings) • LM-24 Triple 8’ (30’ ceilings)
• LMG-12 Triple 4’ (18’ ceilings)
Lagmaster Plus wire plug hangs 12 or 9 gauge wire. No need for ladders,
scaffolding or scissor lifts.
Pre-wrapped wire on eye lags require a special plug (pre-wrapped plug).
HANG WIRE: Move ring into the up position with set screw
Insert the eye lag screw into secured wire
plug. Insert the wire through the hole and
bend the tail down.
Adjust the pole to length and rotate the Rotate the pole again to twist the wire. Pull
screw until it is seated. Pull down on the the wire through the plug to complete the
pole so that the wire is caught on the ring.
installation.
HANG CHAIN: Move ring into the down position with set screw
Secure a #1 1/2 “S” hook to an acoustical
eye lag and to the proper size chain for
your job. Insert it into the LagMaster Plus.
Secure the chain in the magazine so it does
not whip when rotating the pole. Now rotate
the eye lag screw until it is seated.
Lower the LagMaster Plus.
Turn your pole tool into a very long screwdriver. This LagMaster Plus plug works with any 1/4” hex driver.
Install smooth rod with a Minerallac or Caddy spring clip assembly and screw. The Flash fastener is shown here.
OVERHEAD SCREW APPLICATIONS: (1/4” hex plug)
Plug in the LagMaster Plus 1/4” hex head
and insert the proper 1/4” driver. Adjust the
LagMaster pole tool to length.
Push the smooth rod between the pole and
the wire bale on the LagMaster adjusting
pin to keep the rod from whipping while
turning in the screw for safety.
Turn in the screw cautiously being careful
not to over torque or strip the screw.
Remove the tool.
91
TRIANGLE FASTENER CORPORATION

ITW BUILDEXB
Rod hanging made fast
and secure!
SAMMY SUPER SCREWS
Vertical
Horizontal
(800) 486-1832 www.trianglefastener.com
92

E-Z PRODUCTS
E-Z ANCHOR LITE
3/8" 1 5/16"
E-Z MINI ANCHOR
3/8" 1 1/4"
E-Z ANCHOR
E-Z PRODUCTS
Self-Drilling Drywall Anchors
The original! Fast and easy
self-drilling anchors.
E-Z Anchor®, E-Z Anchor Plastic,
E-Z Mini Anchor®, E-Z Hanger®,
E-Z Anchor Lite, E-Z Toggle,
E-Z Anchor Plastic Plus
PRODUCT SPECIFICATIONS
Product Material:
Zinc die cast Nylon
Drilling Capacity:
3/8'', 1/2'' and 5/8''
gypsum wallboard
Light
Duty
Medium
Duty
Heavy
Duty
APPLICATIONS
Electrical Fixtures
Thermostats
HVAC Fixtures
Plumbing Fixtures
Bathroom Accessories
Shelving and Supports
Mirrors
Picture Frames
Brackets
Plaques and Awards
Closet Organizers
Coat Racks
Curtain Rods
Signs
Bulletin Boards
Control Systems
Decorative Wall Hangings
Office Material Holders
Smoke Detectors
Clocks
Kitchen Accessories
Doorbells
Telecommunications
Equipment
Chalk Boards
Remote Control Boxes
SELECTOR GUIDE
Maximum Fixture
Anchor Description Anchor Material Part Number Quantity Thickness
E-Z ANCHOR LITE WHITE NYLON 5006902 100 COUNT 3/4”
E-Z MINI ANCHOR ZINC 5033902 100 COUNT 3/4”
5034902 50 #6 X 1 1/4” SMS
50 #8 X 1 1/4” SMS
E-Z ANCHOR® ZINC 5000902 100 COUNT 3/4”
WHITE NYLON 5003902 100 COUNT
E-Z TOGGLE ZINC 5014901 50 COUNT 5/8”
50 #8 X 2 1/8” PAN SMS
5017901 50 COUNT
50 #8 X 2 1/8” PAN
LARGE WASHER FACE SMS
1/2" 1 5/8"
E-Z TOGGLE
9/16" 2 1/2"
PERFORMANCE DATA
Pullout
Shear
(Ultimate average lbs.)
(Ultimate average lbs.)
Gypsum Thickness
Gypsum Thickness
3/8” 1/2” 5/8” 3/8” 1/2” 5/8”
E-Z Anchor Lite 25 30 40 80 90 120
E-Z Mini Anchor 30 40 50 90 110 140
E-Z Anchor 40 50 75 135 150 200
E-Z Toggle 70 85 150 200 230 300
INSTALLATION GUIDELINES
LIGHT DUTY & MEDIUM DUTY E-Z ANCHORS
1. Place #2 Phillips screwdriver
into recess of E-Z Anchor Lite ,
E-Z Mini Anchor, E-Z Anchor or
E- Z Anchor Plastic Plus.
2. Press into drywall while
turning the anchor clockwise
until it is seated flush with wall.
3. Place fixture in position over
installed E-Z Anchor Lite, E-Z
Mini Anchor, E-Z Anchor, or
Plastic Plus. Insert screw with
screw driver. Tighten fixture in
place.
HEAVY DUTY E-Z TOGGLE
1. Place #2 Phillips screwdriver into
recess of E-Z Toggle. Press into
drywall while turning the anchor
clockwise until it is seated flush
with wall and arrows on head are
parallel to stud.
2. Place fixture in position over
installed E-Z Toggle. Insert screw
and push through E-Z Toggle to
engage clamp.
3. Continue turning screw until
tight. The clamp will move back
against the drywall as the screw
turned.
93
TRIANGLE FASTENER CORPORATION

LIGHT DUTY ANCHORS
BANTAM PIUG
Base material - concrete, block, brick and wallboard
Anchor Material - plastic
The Bantam Plug anchor is a plastic anchor designed for
use with lightweight fixtures with a sheet metal or wood
screw. The anchor is recommended for light duty static
applications where holding power is not a critical factor. It
should not be used overhead.
Cat. Drill Min. Std. Std. Mstr.
No. Size Dia. Depth Box. Ctn. Ctn.
7559 6-8 x 3/4” 3/16” 3/4” 100 1000 5000
7569 8-10 x 7/8” 3/16” 7/8” 100 1000 5000
7579 10-12 x 1” 1/4” 1” 100 1000 5000
7589 14-16 x 1 1/2” 5/16” 1 1/2” 50 500 2500
KITS - SLOTTED/PHILLIPS PAN HEAD
SHEET METAL SCREWS
Cat. Anchor Screw Min. Anchors Std.
No. Kit No. Size Size Depth & Screws Ctn.
8934 8-8 8-10 8 x 1” 7/8” 100 10
8936 8-10 10-12 10 x 1” 1” 100 10
8938 8-12 10-12 12 x 1” 1” 100 10
FLUTED PLASTIC ANCHOR
Base material - concrete, block, brick and stone
Anchor material - plastic
The Fluted Plastic Anchor is designed for light duty fastening
applications with sheet metal or wood screws. Longitudinal ribs on the
anchor body prevent it from turning during tightening of the screw.
This inexpensive plastic screw anchor comes color-coded by diameter
for easy application. The anchor is recommended for light duty static
applications where holding power is not a critical factor.
It should not be used overhead.
Cat. Drill Min. Std. Std.
No. Size Color Dia. Depth Box Ctn.
7500 4-6 x 1 White 3/16 1 100 1000
7505 7-9 x1 Red 7/32 1 100 1000
7510 10-12 x 1 Green 1/4 1 100 1000
7515 10-12 x 1 1/4 Green 1/4 1 1/4 100 1000
7520 10-12 x 1 1/2 Green 1/4 1 1/2 100 1000
7525 14 x 1 Blue 5/16 1 100 1000
7530 14 x 1 1/2 Blue 5/16 1 1/2 100 1000
100 anchors and screws plus one drill bit per kit
SCRU-LEAD
Base material - concrete and block
Anchor material - lead alloy
The Scru-Lead anchor is designed for use with sheet
metal or wood screws in concrete, block or brick. The
anchor is made entirely of lead alloy which is soft enough
for easy installation, yet hard enough to give sure, secure
holding power. The performance of this product depends on
the integrity of the base material. The anchor is
recommended for light duty applications where holding
power is not a critical factor. It should not be used
overhead.
Cat. Drill Min. Std. Std.
No. Size Dia. Depth Box Ctn
9409 6-8 x 3/4” 1/4” 3/4” 100 1000
9414 6-8 x 1” 1/4” 1” 100 1000
9419 6-8 x 1 1/2” 1/4” 1 1/2” 100 1000
9429 10-14 x 1” 5/16” 1” 100 1000
9439 10-14 x 1 1/2” 5/16” 1 1/2” 100 1000
9460 16-18 x 1 1/2” 3/8” 1 1/2” 25 250
LAG SCREW SIZES
Cat Screw Drill Std. Std.
No. Size Dia. Box Ctn.
9080 3/8” x 2” 7/16” 25 250
9082 3/8” x 2 1/2” 7/16” 25 250
9084 3/8” x 3” 7/16” 25 250
FIBERPLUG
Base material - concrete, block, brick,
stone and plaster
Anchor material - jute fiber with lead liner
The Fiberplug is a jute fiber screw style anchor (formerly
known as the Rawl(plug) designed for use in concrete,
block, brick, stone, and plaster. Designed for use with wood,
sheet metal and lag screws.
Cat. Screw Drill Std. Std. Mstr.
No. Size Dia. Box Ctn. Ctn.
9003 6 x 3/4” 5/32” 100 1000 5000
9005 6 x 1” 5/32” 100 1000 5000
9011* 8 x 3/4” 11/64” 100 1000 5000
9013 8 x 1” 11/64” 100 1000 5000
9015* 8 x 1 1/4” 11/64” 100 1000 5000
9017* 8 x 1 1/2” 11/64” 100 1000 5000
9024* 10 x 3/4” 3/16” 100 1000 5000
9026 10 x 1” 3/16” 100 1000 5000
9028 10 x 1 1/4” 3/16” 100 1000 5000
9030 10 x 1 1/2” 3/16” 100 1000 5000
9039 12 x 1” 1/4” 100 1000 5000
9041 12 x 1 1/4” 1/4” 100 1000 5000
9043 12 x 1 1/2” 1/4” 100 1000 5000
9045 12 x 2” 1/4 100 1000 5000
9050 14 x 1” 9/32” 100 1000 5000
9052 14 x 1 1/4” 9/32” 100 1000 5000
9054 14 x 1 1/2” 9/32” 100 1000 5000
9056 14 x 2” 9/32” 100 1000 5000
9063 16 x 1 1/2” 5/16” 50 500 2500
9072 20 x 1 1/2” 3/8” 50 500 2500
9074 20 x 2” 3/8” 50 500 2500
* Discontinued item once current stock is exhausted
(800) 486-1832 www.trianglefastener.com
94

DRYWALL ANCHORS
Drive Polly
Cat. Screw Wall Std. Std.
No. Size Length Thickness Box Ctn.
2180 1/8"x XS 1 3/8” 1/8”-1/4” 100 500
2182 1/8" S 2" 3/8”-1/2” 100 500
2184 1/8” L 2 3/8” 1/2”-3/4” 100 500
XS-Extra Short S-Short L-Long XL-Extra Long
POLLY SETTING TOOL
(FITS ALL SIZES)
Cat. Std. Std.
No. Description Box Ctn.
2150 Polly Setting Tool 1 1
TOGGLE WINGS ONLY
COMBINATION SLOTTED
PHILLIPS HEAD POLLY
Base material - plaster, wallboard, block,
hollow tile and plywood
Anchor material - carbon steel
The PoIIy is a sleeve type hollow wall anchor
designed for use in base materials such as plaster,
wallboard, concrete block, hollow tile or plywood.
Cat. Screw Drill Wall Std. Std.
No. Size Length Dia. Thickness Box Ctn.
2100 1/8" XS 1 1/16" 5/16" 1/8"-1/4” 100 500
2101 1/8” S 1 3/4" 5/16" 3/8"-1/2" 100 500
2102 1/8” L 2 1/4" 5/16" 5/8”-1" 100 500
2103 1/8" XL 2 11/16" 5/16" 1 1/4"-1 1/2" 50 250
2111 3/16” S 2" 3/8" 3/8”-5/8" 50 250
2112 3/16" L 2 1/2" 3/8" 3/4"-1 1/8" 50 250
2113 3/16" XL 3" 3/8" 1 1/4"-1 3/4" 25 125
2121 1/4” S 2 1/4" 7/16" 3/8"-1/2" 50 250
2122 1/4" L 2 3/4" 7/16" 5/8"-1 1/8" 50 250
2123 1/4" XL 3 3/8" 7/16" 1 1/4”-1 3/4" 25 125
Cat Screw Drill Std. Std.
No. Size Dia. Box Ctn.
4000 1/8” 3/8” 100 500
4020 3/16” 1/2” 100 1000
4220 1/4” 5/8” 100 1000
4330 5/16” 7/8” 50 500
4430 3/8” 7/8” 50 500
4540 1/2” 1 1/4” 25 25
TIE WIRE ACOUSTICAL TOGGLE
Cat. Tie Wire Drill Std. Std.
No. Size Hole Size Dia. Box Ctn.
4247 1/4” x 4” 7/32” 5/8” 100 100
4257 1/4” x 5” 7/32” 5/8” 100 100
XS-Extra Short S-Short L-Long XL-Extra Long
95
TRIANGLE FASTENER CORPORATION

DRYWALL ANCHORS
POLY TOGGLE PLASTIC
HOLLOW WALL ANCHOR
Base material - wallboard or solid masonry
Anchor material - plastic
The Poly-Toggle® is a screw actuated hollow wall
anchor for use in paneling, wallboard and solid
masonry available in 6 sizes to match the most
common wall thicknesses. In solid base materials,
the anchor can be used by removing the outer
wings. The performance of this product depends
on the integrity of the base material in which it is
installed. The anchor is recommended for light duty
static application where holding power is not a
critical factor.
Cat. Wall Drill Std. Std.
No. Size Thickness Dia. Box Ctn.
2302 Mini 1/8" 5/16"' 100 1000
2303 Short 3/8" 5175" 100 1000
2304 Medium 1/2" 5/16" 100 1000
2305 Long 5/8" 5/16" 100 1000
2306 Extra Long 3/4" 5/16" 100 1000
2307 Super Long 1" 5/16" 100 1000
Pop Toggle Cat. Std. Std.
Base material - gypsum wallboard, plaster,
some hollow masonry
Anchor material - plastic
Pop Toggle fasteners are hollow wall anchors
ideal for static applications requiring light to
medium load performance. Installation is very fast,
needing a pre-drilled 5/16" diameter hole. The
fastener pre-installs without a screw, allowing for
easy placement and removal of the fixture. Pop
Toggle fasteners are not recommended
for use overhead or applications where
holding values are critical.
No. Description Box Ctn.
04060 Pop Toggle Small 100 1000
04062 Pop Toggle MedIum 100 1000
04064 Pop Toggle Large 100 1000
Ask for our fastening catalog
for commercial drywall
applications!
(800) 486-1832 www.trianglefastener.com
96

STRAP TOGGLE
STRAP-TOGGLE TM
Product Description
The Strap-Toggle is a pre-assembled anchor consisting of a carbon steel wing and a locking cap/ratchet leg
assembly molded from engineered plastic. It is available in both 3/16”, 1/4”, 3/8" and 1/2” sizes. When compared
to traditional toggles, this unique anchor can be installed in a smaller hole and does not require a fixture or screw
to set it. The anchor can be easily adjusted to accommodate a wall thickness of up to 2-1/2” while using a shorter
bolt.
Installation is simple and four times taster than traditional toggles or metal hollow wall anchors. The specially
designed locking cap and ratchet leg holds the wing snugly against the inside of a hollow wall. This prevents the
anchor from spinning during installation of the bolt and allows for easy removal of the fixture for maintenance.
Installation of the anchor is easy. Simply drill a hole into the cavity of the hollow base material and insert the
anchor. Then pull the ring and slide the cap along the straps until the flange of the cap is firmly set against the
surface of the base material. Snap the straps off and the anchor is ready for use. It's that simple! The bolt and
fixture may be installed and removed as often as necessary without affecting the anchor.
Drill the proper size hole into
the cavity of the hollow base
material .
Position the wing parallel to the plastic legs and
slide the anchor through the drilled hole into the
hollow cavity.
INSTALLATION INSTRUCTIONS
Pull the wing firmly against the inside wall of the
hollow material using the ring, then slide the
plastic cap forward until the flange is seated
flush against the work surface.
Place your thumb between the plastic
straps and snap the straps off.
Position the fixture. Insert the bolt though the
fixture and tighten. The minimum bolt length
should be at least 1/2 longer than the combined
wall and fixture thickness.
The following approvals and listings are for reference purposes. They should be reviewed by the design professional responsible for the product
installation to verify approved sizes, base materials, and compliance with local codes.
FEDERAL SPECIFICATION
The Strap-Toggle meets the descriptive requirements of FF-B-588D, Type V for a captive toggle.
Anchors for hollow walls shall be a pre-assembled captive style toggles meeting the requirements of Federal Specification FF-B-588D, Type V The
anchors shall have a carbon steel wing portion formed in a 'U' channel shape that is zinc plated according to ASTM Specification B633, SC 1, Type
Ill. The anchor shall have a locking cap and ratchet leg assembly molded from engineered plastic. The assembly shall hold the wing snugly against
the inside of the hollow wall prior to installation and after removal of the bolt. Strap Toggle anchors shall be as supplied by Powers Fasteners, Inc.
97
TRIANGLE FASTENER CORPORATION

STRAP TOGGLE
STRAP TOGGLE
Sizes
The Strap-Toggle is a heavy duty
hollow wall anchor designed for
use in base materials such as
plaster, wallboard, concrete block
or hollow tile.
ANCHOR SIZES
Cat Drill Wall Std. Std. Wt./
No. Size Diameter Thickness Box Ctn. 100
4052 3/16” x4” 1/2” 2 1/2” 50 300 3 1/2
4054 1/4” x4” 1/2” 2 1/2” 50 300 3 1/2
4056 3/8” x4” 3/4" 2 1/2" 25 150 5
4058 1/2” x4” 3/4” 2 1/2” 25 150 5
INSTALLATION SPECIFICATIONS
Anchor
Size 3/16” 1/4” 3/8” 1/2”
ANSI Drill Bit Size* 1/2” 1/2” 3/4” 3/4”
Cap Size 5/8” 5/8” 1” 1”
Grip Range 2 1/2” 2 1/2” 2 1/2” 2 1/2”
Thread Size 3/16”-24 1/4”-20 3/8”-16 1/2”-13
Max. Torque (ft.-lbs.) 5 5 5 5
Minimum Clearance 1 7/8” 1 7/8” 1 7/8” 1 7/8”
* 9/16” Bit may be required for very dense materials.
MATERIAL SPECIFICATIONS
Anchor Component
Component Material
Wing
AiSi ClOlO
Zinc Plating ASTM B633, Sd, Type iii, (Fe/zn 5)
Cap / Strap
Engineered Plastic
Performance Data
The following ultimate load capabilities are based on testing according to ASTM E 488.
ULTIMATE LOAD CAPACITIES FOR GYPSUM WALLBOARD
Wallboard Thickness
Size Drill Dia. 3/8” 1/2” 5/8” 3/4”
Tension (lbs.) 3/16” 1/2” 120 130 195 205
1/4” 1/2” 130 145 210 215
3/8” 3/4” 135 150 220 230
1/2” 3/4” 140 150 220 230
Shear (lbs.) 3/16” 1/2” 240 285 380 440
1/4” 1/2" 270 295 420 470
3/8” 3/4” 275 300 420 475
1/2" 3/4” 290 355 430 485
ULTIMATE LOAD CAPACITIES FOR C-90 HOLLOW BACK
ASTM C-90 Hollow Back
Size Drill Dia. Tension (Lbs.) Shear (Lbs.)
3/16" 1/2” 1,080 740
1/4” 1/2” 1,355 1,420
3/8” 3/4" 1,435 2,330
1/2” 3/4” 1,720 2,980
NOTE: The values listed above are ultimate load capabilities. These capabilities should be reduced by a minimum
safety factor of4 or greater to determine the allowable working load. Refer to the Fastening Systems Design Manual published by Powers Fasteners, Inc. for
complete details. Since the consistency of gypsum wallboard and hollow block varies greatly these load capacities listed should be used as guidelines only Job
site tests should be conducted to determine the actual load capabilities.
(800) 486-1832 www.trianglefastener.com
98

ITW BUILDEXB
GYP-FAST
99
TRIANGLE FASTENER CORPORATION

ITW BUILDEXB
GYP-FAST
(800) 486-1832 www.trianglefastener.com 100

ITW BUILDEXB
GYP-FAST AIR
101
TRIANGLE FASTENER CORPORATION

ITW BUILDEXB
GYP-FAST AIR
(800) 486-1832 www.trianglefastener.com 102

ITW BUILDEXB
GRID-MATE SCREWS
WOOD/LIGHT METAL SCREWS
For use with plywood. OSB, dimensional lumber and light
gauge metal 26 gauge - 20 gauge.
• #2 Phillips bugle head.
• Climacoat ® finish.
• Hi-lo thread form.
STEEL FRAMING SCREWS
For use with steel framing from 20 gauge -12 gauge.
• #2 Phillips bugle head.
• Climacoat ® finish.
• S-12 drill point.
MASONRY SCREWS
For use with brick, block and concrete.
• 10 Carbide bits per 1000 piece carton.
• #2 Phillips flat head.
• Blue Climaseal ® finish. Original Tapcon
masonry anchor.
GRID-MATE PB
Wood/light metal - For use with
plywood, OSB, dimensional lumber
and light gauge metal (26 gauge - 20
gauge).
Masonry - For use with brick, block
and concrete (2) Phillips and (5)
carbide bits per carton.
Steel - For use with steel framing from
20 gauge - 12 gauge. For attachment
over gypsum. use next length of
screw.
103
For use in polymer based (PB) barrier and water managed systems.
SIZES
Part No. Description Ctn. Qty. Ctn. Wgt.
2311599 6 x 1 5/8” 5000 23
2312500 8 x 2” 3500 28
2313500 8 x 2 1/2” 2500 21
2314500 8 x 3” 2000 20
2315500 10 x 4” 1000 12
2316500 10 x 5” 1000 23
2317500 10 x 6” 1000 27
Part No. Description Ctn. Qty. Ctn. Wgt.
2321500 6 x 1 5/8” 5000 25
2318500 8 x 2” 3500 28
2319500 8 x 2 5/8” 2500 26
2320500 8 x 3” 2000 24
2322500 10 x 4” 1000 21
2323500 10 x 5” 1000 26
Part No. Description Ctn. Qty. Ctn. Wgt.
3171407 3/16 x 1 1/4” 100/1000 10
3173407 3/16 x 2 1/4” 100/1000 12
3175407 3/16 x 2 3/4” 100/1000 15
3177407 3/16 x 3 1/4” 100/1000 17
3181407 3/16 x 4” 100/1000 21
Part Insulation Screw Ctn. Ctn.
Item Number Thickness Length Qty. Wgt.
WLM1 2349500 1” 1 5/8” 1000 16
WLM2 2350500 1 1/2” 2” 1000 18
WLM3 2351500 2” 2 1/2" 1000 20
WLM4 2358500 2 1/2' 3” 1000 21
WLM5 2359500 3”, 3 1/2” 4” 500 24
WLM6 2360500 4” 5" 500 34
Part Insulation Screw Ctn. Ctn.
Item Number Thickness Length Qty. Wgt.
M1 2368400 1" 1 3/4” 1000 21
M2 2369400 1 1/2” 2 1/4” 1000 24
M3 2370400 2” 2 3/4” 1000 26
M4 2371400 2 1/2” 3 1/4” 1000 28
M5 2372400 3” 4” 500 31
Part Insulation Screw Ctn. Ctn.
Item Number Thickness Length Qty. Wgt.
S1 2362500 1” 1 5/8” 1000 16
S2 2363500 1 1/2” 2” 1000 19
S3 2364500 2" 2 1 2” 1000 21
S4 2365500 2 1/2” 3” 1000 23
S5 2366500 3, 3 1 2” 4” 500 32
S6 2367500 4” 5” 500 37
TRIANGLE FASTENER CORPORATION

TRACER CB CEMENT BOARD SCREW
TRACER CB
For attachment of cement board in
Direct Applied (DEFS) Systems, tile
backer and underlayment applications.
Length Attachment Range Applications
Hi-Lo ®
9 x 1 1/4” Up to 3/4” material thickness to wood:
3/8” - “ material thickness to steel
9 x 1 5/8” Up to 1 1/8” material thickness to wood:
3/8” - 1 3/8” material thickness to steel
9 x 2 1/4” Up to 1 3/4” material thickness to wood:
1” to 1 7/8” material thickness to steel
Self-driller
8 x 1 1/4" 3/8” to 3/4” material thickness
8 x 1 5/8" 3/8” to 1 1/4” material thickness
8 x 2 1/4” 1” to 1 7/8” material thickness
Cement board to wood
or light gauge
steel 26-20 gauge
Cement board to steel studs 20-12
gauge
Deep #2 phillips recess for positive driving.
Countersinking rib design allows flush seating to board.
Long life coating eliminates bleed through.
(800) 486-1832 www.trianglefastener.com
104

POWDER ACTUATED FASTENING
D45A
• Most durable, powerful powder
tool.
• Designed for high-production use
in steel and concrete.
• Semi-automatic.
• 2” pin capacity (2 1¼2” w/washer).
• 5-year warranty (10-year warranty
on muzzle bushing).
• Ramset’s patented red disc gives
you the power you need.
• Fasten into the hardest of concrete
and steel with a red disc load and
the D45A. The patented 10-shot
disc load advances only after firing
which eliminates wasted loads.
SPECIFICATIONS
.25 caliber 10-shot disc loads
2 (Brown)
3 (Green)
4 (Yellow)
5 (Red)
Weight
4 1/2 pounds
Height
7 1/2 inches
Length
15 inches
Muzzle bushing O.D. 5/8”
Pin capacity
2 or 2 1/2” washered
• Single shot.
• 1 1/2” pin capacity.
• 5-year warranty.
721
• .22 caliber “A” crimped
powder loads in four power
levels (gray, brown, green,
yellow).
SPECIFICATIONS
.22 caliber Single-shot loads
1 (Gray)
2 (Brown)
3 (Green)
4 (Yellow)
Weight
4.3 pounds
Length
13 1/2 inches
Muzzle bushing O.D. 5/8”
Pin capacity 1 1/2”
Factory Mutual System approved
D60
SPECIFICATIONS
.25 caliber 10-shot disc loads
2 (Brown)
3 (Green)
4 (Yellow)
Weight
4.9 pounds
Length
12 1¼2 inches
Muzzle bushing O.D. 3/4”
Pin capacity 2 3/8”
• Quick power adjustment.
• Gives eight levels of power
with only one load level for a
variety of applications.
• Semi-automatic.
• 2 3/8” pin capacity
(2 1¼2” w/washer).
• 5-year warranty.
• Patented 10-shot disc loads
advance automatically,
eliminating wasted loads.
N.E.C. Code 300.11 (Independent
Hanging Wires Required)
Means you need fast, frequent
fastening to get your job done before a
ceiling contractor closes up.
Complies with OSHA and ANSI
standards.
105
TRIANGLE FASTENER CORPORATION

POWDER ACTUATED FASTENING
• Semi-automatic
• 2 1/2” pin capacity (3” w/washer)
• 5-year warranty
• Uses Loadsaver 10-shot strip load
SA270
SPECIFICATIONS
.27 caliber 10-shot strip loads
3 (Green)
4 (Yellow)
5 (Red)
Weight
5 3/4 pounds
Length
15 inches
Muzzle bushing O.D. 5/8”
Pin capacity
2 1/2” (3” w/washer)
Complies with OSHA and ANSI standards.
ICBO Evaluation Service, Inc. – #ER-1147
(for sill plate applications)
• Semi-automatic.
VIPER
• 30% faster
overhead attachment.
• 5-year warranty
(10-year warranty on
muzzle bushing).
• Uses Loadsaver 10-shot strip load.
SPECIFICATIONS
.27 caliber 10-shot strip loads
3 (Green)
4 (Yellow)
5 (Red)
Weight
4.5 pounds
Pin capacity ceiling clips 1 1/4”
Length
17 inches
Complies with OSHA and ANSI
standards.
L1600 LADD
OVERHEAD FASTENING SYSTEM
SPECIFICATIONS
.22 caliber crimped loads 4 (Yellow)
5 (Red)
Weight
2.8 pounds
Height
13 inches
Complies with OSHA and ANSI standards.
1 2 3 4 5
• Single shot.
• .22 caliber crimped loads.
• It is important to use only
loads specifically designed
for use in the L1600 tool.
• Preassembled clip & pin
speeds installation and
reduces labor cost.
• Sturdiest clip on the market
for improved pullover
performance
• Accurate, positive
attachment of hanger wire
from concrete ceilings and
steel.
• Elongated wire hole allows
for freedom of movement of
wire loop.
• 9/32” hole allows pencil rod
to be suspended.
•No need for ladders or
scaffolding with the LADD
Fastening System.
1 Ejection pin
2 Barrel
3 Gas expansion chamber
4 Cartridge and chamber
5 Clip assembly
(800) 486-1832 www.trianglefastener.com
106

POWDER ACTUATED FASTENING
COBRA
• Semi-automatic.
• 2 1/2” pin capacity (3” w/washer).
• Uses Loadsaver 10-shot strip loads.
• Low velocity piston drive tool provides added safety on the
job
SPECIFICATIONS
Weight
4 1/2 pounds
Length 13 1/4”
Muzzle bushing O.D. 9/16”
.27 caliber 10-shot strip loads
3 (Green)
4 (Yellow)
5 (Red)
Pin capacity
2 1/2” (3” w/washer)
MD380
SPECIFICATIONS
.27 caliber Long single-shot loads
4 (Yellow)
5 (Red)
6 (Purple)
Weight
6 3/4 pounds
Length
15 inches
Muzzle bushing O.D. 3/4”
Pin Capacity 3”
Factory Mutual System approval
• Single shot.
• 3” pin capacity.
• 5-year warranty.
• .27 caliber long “A” crimped powder loads in three power
levels (yellow, red, purple).
107
TRIANGLE FASTENER CORPORATION

DRIVE PINS
POWERPOINT PINS FOR HARD CONCRETE AND STEEL FASTENING
SELECTION CHART FOR BASE STEEL THICKNESS
Material 3/16” 1/4” 3/8" 1/2” 3/4”
1/4” Plywood SP58* SP34* SP78** SP78** SP78**
3/8” Plywood SP58* SP34* SP78** SP78** SP78**
1/2” Plywood SP100** SP100** SP100** SP100** SP100**
3/4” Plywood SP114** SP114** SP114** SP114** SP114**
2' x 4' Plate SP178** SP178** SP178** SP178** SP178**
10 ga. to 12 ga. SP58* SP34* SP34* SP78** SP58**
13 ga. to 17 ga. SP12* SP58* SP34* SP34** SP58**
18 ga. to 25 ga. SP12* SP58* SP34* SP34** SP58**
* For use with all Ramset Powder Tools
** For use with all Ramset Powder Tools except the Model 721
SELECTION CHART FOR PRODUCT
Part Number Nom. Shank Diameter Shank Length In. Shank Length mm Box Qty.
SP12 .150 1/2 (12.7) 100
SP58 .150 5/8 (15.9) 100
SP34 .150 3/4 (19.1) 100
SP78 .150 7/8 (22.2) 100
SP100 .150/.180 1 (25.4) 100
SP114 .150/.180 1-1/4 (31.8) 100
SP112 .150/.180 1-1/2 (38.1) 100
SP178 .150/.180 1-7/8 (47.6) 100
For optimum results in hard steel, use the D45 powder actuated tool.
BLACK TRACK PINS
• .300 head diameter drive pins.
• Designed for use in concrete and structural
steel applications.
• Available in 100 or 1000 pack.
The special black coating improves pin penetration into
difficult base material (i.e. hard concrete). We offer this
black coating on all of our fasteners manufactured for
the attachment of drywall track and channel to concrete
and steel.
SELECTION CHART
Part Shank Length Auto D45/
Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70
1503KBC 1/2 knurled (12.7) - - - - - - -
1506BC 3/4 (19.1) - - - - - - -
1508BC 1 (25.4) - - - - - - -
Shank diameter = .145
DRIVE PINS
• .300 head diameter drive pins.
• Designed for use in concrete and structural steel applications.
• 100 pin pack.
SELECTION CHART
Part Shank Length Auto D45/
Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70
1503K* 1/2 Knurled (12.7) - - - - - - -
1506* 3/4 (19.1) - - - - - - -
1508* 1 (25.4) - - - - - - -
1510* 1-1/4 (31.8) - - - - - - -
1512 1-1/2 (38.1) - - - - - -
1513 1-3/4 (44.5) - - - - - -
1514 2 (50.8) - - - - - -
1515 2-3/8 (60.3) - - - - -
1516 2-1/2 (63.5) - - - -
1524 3 (76.2) - -
* Also available in 1000 Pack
Shank diameter = .145
(800) 486-1832 www.trianglefastener.com
108

DRIVE PINS
DRIVE PINS
• .300 head diameter drive pins with 7/8” washer.
• Washer increases bearing surface against the material to be fastened.
• 100 pin pack.
SELECTION CHART
Part Shank Length Auto D45/
Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70
1506SD 3/4 (19.1)
1508SD 1 (25.4)
1510SD 1-1/4 (31.8)
1512SD 1-1/2 (38.1)
1514SD 2 (50.8)
1516SDC 2-1/2 (63.5)
1524SDP* 3 (76.2)
* Square washer indicates 3" pin has been installed
Shank diameter = .145
TOP HAT DRIVE PINS
• .300 head diameter top-hat.
• Increases the bearing surface against the material to be fastened for improved attachment to
inconsistent base materials in 100 pin pack and 1000 pack.
SELECTION CHART
Part Shank Length AUTO D45/
Number In. (mm) 721 FAST D60 SA270 D45A Cobra M70
1903K 1/2 Knurled (12.7)
1906 3/4 (19.1)
1906M 3/4 (19.1)
1908 1 (25.4)
1908M 1 (25.4)
Shank diameter = .145
POWERPOINT PINS
• Premium steel and hard concrete pin.
• Pin for fastening into harder steel and concrete.
• 100 Pin Pack
SELECTION CHART
Part Shank Length Auto D45/
Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70
SP12 1/2 (12.7)
SP58 5/8 (15.9)
SP34 3/4 (19.1)
SP78 7/8 (22.2)
Shank diameter = .145
POWERPOINT STEP SHANK PINS
• Premium steel and hard concrete pin.
• Pin for fastening into harder steel and concrete.
• 100 pin pack.
SELECTION CHART
Part Shank Length Auto D45/
Number In. (mm) Fast D60 SA270 D45A Cobra M70
SP100 1 (25.4) s s s s s s
SP114 1-1/4 (31.8) s s s s s s
SP112 1-1/2 (38.1) s s s s s s
SP178 1-7/8 (47.6) s s s s s s
Shank diameter = .145
109
TRIANGLE FASTENER CORPORATION

DRIVE PINS AND CLIPS
THREADED STUDS
• For applications that require removability, where shimming is required.
SELECTION CHART
Part Thread Shank Length
Number Length In. (mm) Auto D45/
In. (mm) 721 Fast D60 SA270 *D45A Cobra M70 Viper
1623WK 3/4 (19.1) 1/2 knurled (12.7)
1642W 1/2 (12.7) 1 (25.4)
1643W 3/4 (19.1) 1 (25.4)
1644W 1 (25.4) 1 (25.4)
1653W 3/4 (19.1) 1 1/4 (31.8)
Shank diameter = .145
3/8"-16 THREADED STUD
SELECTION CHART
Part Thread Length Shank Length
Number In. (mm) In. (mm) MD380
9140K 1 (25.4) 5/8 knurled (15.9)
9150 1 (25.4) 1 1/16 (27.0)
9190 1 (25.4) 1 1/4 (31.8)
Shank diameter = .205
CEILING CLIP ASSEMBLIES
• .300 head diameter pin.
• Fastener is preassembled to 14 gauge angle clip for applications such as the hanging of ceiling wire
to support ceiling grid.
• Available in 1000 pack only.
Part Description Auto D45/
Number 721 Fast D60 SA270 D45A Viper*
2202 Ceiling Clip w/1 1/4”
* Viper tool comes assembled with the 2VP4125 nosepiece.
Shank diameter = .145
SELECTION CHART
Part Pin Length Auto D45/
Number In. (mm) 721 Fast D60 SA270 D45A Cobra Viper
SDC100 1 (25.4)
SDC125* 1 1/4 (31.8)
* Available in 100-Pack
Shank diameter = .145
SELECTION CHART
(800) 486-1832 www.trianglefastener.com
110

PINS AND CLIPS
POWERPOINT PINS WITH CEILING CLIP
• .300 head diameter pin for hard concrete.
SELECTION CHART
Part Pin Length Auto D45/
Number In. (mm) Fast D60 SA270 D45A Cobra Viper
SPC78 7/8 (22.2)
SPC114 1 1/4 (31.8)
SPC78 shank diameter = .150
SPC114 shank diameter = .150/.180
CONDUIT CLIP ASSEMBLIES
.300 Head Diameter Pin
• Fastener is preassembled to conduit clip to attach electrical conduit to concrete or steel.
SELECTION CHART
Part Description Auto D45/
Number 721 Fast D60 SA270 D45A Cobra M70 Viper
38BXSP78C 3/8” bx clip with 7/8” pin
12EMTSP78C 1/2” conduit clip with 7/8” pin
34EMTSP78C 3/4” conduit clip with 7/8” pin
Shank diameter = .150
FASTENER ANGLE CLIP
SELECTION CHART
Part
Number
1202CF
Description
Angle clip (no pin)
LADD ASSEMBLY FOR L1600
Part Pin Length Description
Number In. (mm)
L652 1 1/4 (31.8) Preassembled pin & clip
Shank diameter = .152
SELECTION CHART
111
TRIANGLE FASTENER CORPORATION

POWDER LOADS
HIGH QUALITY AND DEPENDABILITY
RAMSET LOADS FOR LOW VELOCITY TOOLS
Tool Part Power Case Caliber/
Model Number Level Color Color Type Packaging
D60/D60L 2D60 2 Brown Brass .25 Disc 10 Discs/Box
D45/D45A 3D60 3 Green Brass .25 Disc 10 Discs/Box
AutoFast 4D60 4 Yellow Brass .25 Disc 10 Discs/Box
D45/D45A and
AutoFast 5D45 5 Red Brass .25 Disc 10 Discs/Box
721 12CW 1 Gray Brass .22 Single 100/Box
4170 32CW 3 Green Brass .22 Single 100/Box
M70 42CW 4 Yellow Brass .22 Single 100/Box
SA270 3RS27 3 Green Brass .27 Strip 10 Strips/Box
Cobra 4RS27 4 Yellow Brass .27 Strip 10 Strips/Box
Viper 5RS27 5 Red Brass .27 Strip 10 Strips/Box
MD380 4RL27 4 Yellow Brass .27 Single 100/Box
5RL27 5 Red Brass .27 Single 100/Box
6RL27 6 Purple Brass .27 Single 100/Box
L1600 L674 4 Yellow Brass .22 Single 100/Box
Tool Part Power Case Caliber/
Model Number Level Color Color Type Packaging
DX-350, DX-351 3RS27 3 Green Brass .27 Strip 10 Strips/Box
4RS27 4 Yellow Brass .27 Strip 10 Strips/Box
DX-350, DX-351
DX-36M, DX-451 5RS27 5 Red Brass .27 Strip 10 Strips/Box
DX-451 6RS27 6 Purple Brass .27 Strip 10 Strips/Box
DX-600N 4RL27 4 Yellow Brass .27 Single 100/Box
5RL27 5 Red Brass .27 Single 100/Box
6RL27 6 Purple Brass .27 Single 100/Box
DXE37 12CW 1 Gray Brass .22 Single 100/Box
DXE72 22CW 2 Brown Brass .22 Single 100/Box
32CW 3 Green Brass .22 Single 100/Box
42CW 4 Yellow Brass .22 Single 100/Box
1000-Pak/100 Strips/Box
Hilti ® is a registered trademark of Hilti Corp.
RAMSET LOADS FOR HILTI TOOLS
(800) 486-1832 www.trianglefastener.com
112

TECHNICAL DATA
ITW RAMSET/RED HEAD LOW VELOCITY FASTENERS
Performance Table
ALLOWABLE WORKING VALUES LBS. (KN) IN A36 STEEL
Installed in Steel
Steel Thickness In. (mm)
Part Shank 3/16 (4.76) 1/4 (6.35) 3/8 (9.53) 1/2 (12.7) 3/4 (19.1)
Number Diameter Type of Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear
Series In. (mm) Shank Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)
1500, 1600
& 1900
series straight 0.145(3.7) Smooth 130 (0.57) 665 (2.93) 270 (1.19) 700 (3.08) 370 (1.65) 840 (3.74) -- -- -- --
Shank Fasteners
SD Series
1/2” Plywood 0.145 (3.7) Smooth 75 (0.33) 200 (0.88) 110 (0.48) 250 (1.10) 218 (0.97) 276 (1.23) -- -- -- --
2X Doug fir 90 (0.40) 235 (1.03) 160 (0.70) 255 (1.12) -- -- -- -- -- --
9100 Series 0.205 (5.2) Knurled -- -- 480 (2.11) 1,565 (6.89) 550 (2.42) 1,950 (8.58) -- -- -- --
Ladd ceiling
system 0.152 (3.9) Smooth 137 (0.60) -- -- -- -- -- -- -- -- --
SP Series 0.150 (3.8) Smooth 170 (0.76) 645 (2.87) 220 (0.98) 610 (2.71) 295 (1.31) 710 (3.16) 340 (1.51) 754 (2.96) 294 (1.31) 659 (2.93)
Note 1. Values shown reflect a 10 to 1 safety factor for tension and 5 to 1 for shear.
Note 2. Values shown are for fastenings that have the entire pointed end of the fastener driven through the steel plate.
Note 3. Job-site testing may be required to determine actual job-site values.
Note 4. Cyclic, fatigue or shock loads and other design criteria may require a different safety factor.
Note 5. Fastener penetration is 9/16" (14.3mm) minimum (Reference 1/2" (12.7mm) steel, SP series Shear Data 754 lbs (2.96 kN).
Note 6. Fastener penetration is 19/32" (15.1mm)minimum (Reference 3/4" (19.1mm) steel, SP series Tension data 294 lbs (1.31 kN).
Note 7. Fastener penetration is 1/2" (12.7mm) minimum (Reference 3/4" (19.1mm) steel, SP series Shear data 659 lbs (2.93 kN).
ALLOWABLE WORKING VALUES LBS. (KN) IN CONCRETE
Installed in Stone Aggregate Concrete
Concrete Compressive Strength psi (MPa)
Installed in Lightweight
Aggregate Concrete
Strength PSI (MPa)
2000 psi 3000 psi 4000 psi 3000 psi
(13.8 MPa) (20.7 MPa) (27.6 MPa) (20.7 MPa)
Number Shank Min.
Number Diameter Penetration Tension Shear Tension Shear Tension Shear Tension Shear
Series In. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)
1500, 1600 3/4 (19.1) 45 (0.20) 80 (0.35) 70 (0.31) 115 (0.51) 90 (0.40) 145 (0.64) 80 (0.34) 85 (0.37)
& 1900 Series 0.145 (3.7) 1 (25.4) 110 (0.48) 165 (0.73) 175 (0.77) 185 (0.81) 235 (1.03) 205 (0.90) 143 (0.63) 152 (0.67)
straight shank 1 1/4 (31.8) 130 (0.57) 190 (0.84) 180 (0.79) 215 (0.95) 230 (1.01) 240 (1.06) 168 (0.74) 187 (0.82)
fasteners 1 1/2 (38.1) 187 (0.82) 200 (0.88) 227 (1.00) 233 (0.98) 268 (1.18) 247 (1.09) 175 (0.77) 210 (0.92)
SDC100 3/4 (19.1) 80 (0.35) -- 120 (0.53) -- 130 (0.57) -- -- --
SDC125 0.145 (3.7) 1 (25.4) 80 (0.35) -- 120 (0.53) -- 130 (0.57) -- 95 (0.42) --
2202
ceiling clip 0.145 (3.7) 1 1/8 (28.6) -- -- 96 (0.42) 180 (0.79) 98 (0.43) 193 (0.85) -- --
9100 13/16 (20.7) 80 (0.35) 125 (0.55) 90 (0.40) 145 (0.64) 105 (0.46) 170 (0.75) -- --
Series 1 1/16 (27.0) 115 (0.51) 265 (1.17) 150 (0.66) 250 (1.10) 190 (0.84) 230 (1.01) -- --
1 1/4 (31.8) 165 (0.73) 315 (1.39) 230 (1.01) 330 (1.45) 295 (1.30) 350 (1.54) -- --
Ladd Ceiling
System 0.152 (3.9) 1 1/8 (28.6) -- -- 211 (0.93) -- 193 (0.85) -- -- --
Note 1. Except as noted, values shown reflect an 8 to 1 safety factor.
Note 2. Bold values shown reflect 10 to 1 safety factor due to shallow embedment.
Note 3. Values shown are for concrete at the designed strength and are for the fastener or clip system only. Wood, steel, etc. Connected members must be investigated separately.
Note 4. Cyclic, fatigue or shock loads and other design criteria may require a different safety factor.
Note 5. Job-site testing may be required to determine actual job-site values.
Note 6. Tension value for a 3/4" (19.1mm) min. embedment in Precast Hollow 5000 psi (34.5 MPa) is 95 lbs. (0.42 kN) (Ref SDC100).
Note 7. Edge distance is 3" unless otherwise approved.
113
TRIANGLE FASTENER CORPORATION

ERISTRUT
®
CHANNEL FRAMING & RELATED PRODUCTS
CHANNEL FRAME
MODEL NO. 2STR
Description
Sizes
2 hole pipe strap 1/2”, 3/4” 1”, 1 1/4”, 1 1/2” 2”
2 1/2”, 3”, 3 1/2”, 4”, 5”, 6”
CHANNEL FRAME
MODEL NO. A12S
Description
Colors
1 5/8” ga 10’ full slot aluminum, green, pre-galv
CHANNEL FRAME
MODEL NO. A12H
CHANNEL FRAME
MODEL NO. BC17A, BC17D, BC17
Description
Colors
Description
Model Number
1 5/8” ga. 10’ half slot aluminum, green, pre-galv.
Channel beam clamp assembly BC17A
for a,b,c & m channel
Channel beam clamp assembly BC17D
for d & e channel
Plate only for bc17 beam clamp BC17PL
CHANNEL FRAME
MODEL NO. BC18
Description
Size
Channel I-beam clamp 3/8”, 1/2”
CHANNEL FRAME
MODEL NO. BC19
Description
Channel beam clamp
Model Number
bc19
CHANNEL FRAME
MODEL NO. BC20
Description
Beam clip
Model Number
bc200000eg
(800) 486-1832 www.trianglefastener.com 114

ERISTRUT
®
STRUT CLAMPS
NOTE: WHEN USED AS A STRUT
HANGER THE MINIMUM
REQUIRED IS TWO
115
Description
Z beam clip
CHANNEL FRAMING & RELATED PRODUCTS
CHANNEL FRAME
MODEL NO. BC21
Description
Universal beam clamp 1/4”
Model Number
bc21
CHANNEL FRAME
MODEL NO. BC26
Model Number
bc26
BEAM CLAMPS
UP TO1" FLANGE
3/4 TO 1 5/8”
FLANGE
CHANNEL FRAME
MODEL NOS. BC23A, BC23C
Description
Spreader caps for A channel
Spreader caps for C channel
CHANNEL FRAME
MODEL NO. BC70
Description
Channel beam clamp for a, b, c & m 4-6
Channel beam clamp for a, b, c & m 6-9
Channel beam clamp for a, b, c & m 9-12
Channel beam clamp for a, b, c & m 12-15
Model Number
bc23a000eg
bc23c000eg
Part Number
· More versatile alternative to window bracket or
standard beam clamp.
· Strut to beam flanges up to 3/4" thickness for 1
5/8" deep strut.
· Fits C purlin with 3/4" lip height (max) when used
with 1-5/8" deep strut.
· Lock nut and hardened cup point setscrew provide
secure grip on tapered sections.
· Corrosive resistant
galvanized finish.
· Available in hot dipped
galvanized finish. (Special order).
· Permits strut channel opening
positioning in any direction.
· For flange sizes up to 1 when
used as a beam clamp.
TRIANGLE FASTENER CORPORATION
bc700406eg
bc700609eg
bc700912eg
bc701215eg

ERISTRUT®
CHANNEL FRAMING & RELATED PRODUCTS
CHANNEL FRAME
MODEL NO. C12H
CHANNEL FRAME
MODEL NO. EPS
Description Sizes
Description
Colors
1 hole E.M.T. strap 1/2”, 3/4”, 1”, 1 1/4”, 1 1/2”, 2”
13/16” ga 10’ half slot aluminum, green, pre-galv.
1/4”, 3/8”, 5“and 6” size
CHANNEL FRAME
MODEL NO. COPC
CHANNEL FRAME
MODEL NO. F09
Description
Size
2 hole splice plate 3 1/2
Watch for one piece
design with retained bolt.
1/2” - 4” size
Description
Copper tubing
pipe clamp
Sizes
1/4 (3/8 od), 3/8 (1/2 od),
1/2 (5/8 od), 5/8 (3/4 od),
3/4 (7/8 od), 1 (1 1/8 od),
1 1/4 (1 3/8 od), 1 1/2 (1 5/8 od),
2 (2 1/8 od), 2 1/2 (2 5/8 od),
3 (3 1/8 od), 3 1/2 (3 5/8 od),
4 (4 1/8 od), 5 (5 1/8 od),
6 (6 1/8 od)
CHANNEL FRAME
MODEL NOS. F13, F14, F15,
F16, F17, F18
Description
Model Number
CHANNEL FRAME
MODEL NO. OD
Square channel washer 1/4” - 5/16” f130000eg
Note: 1/4” applications require additional 1/4” washer
Square channel washer 3/8” f140000eg
Square channel washer 1/2” f150000eg
Square channel washer 5/8” f160000eg
Square channel washer 3/4” f170000eg
Square channel washer 7/8” f180000eg
Description
Sizes
Large sizes available
upon request.
OD pipe clamp 1/4”, 3/8”, 1/2”, 5/8”, 3/4”, 7/8”, 1
for tubing 1 1/8”, 1 1/4”, 1 3/8”, 1 1/2”, 1 5/8”,
1 3/4”, 1 7/8, 2”, 2 1/8”, 2 1/4”, 2 3/8”,
2 1/2”, 2 5/8”, 2 3/4”, 2 7/8”, 3, 3 1/8”,
3 1/4”, 3 3/8”, 3 1/2”, 3 5/8”, 3 3/4”,
3 7/8”, 4”, 4 1/8”, 4 1/4”, 4 3/8”,
4 1/2”, 4 5/8”, 4 3/4”, 4 7/8”, 5”, 5 1/8”,
5 1/4”, 5 3/8”, 5 1/2”, 5 5/8”, 5 3/4”
5 7/8”, 6”, 6 1/8”, 6 1/4” 6 3/8”, 6 1/2”,
6 5/8”, 6 3/4”, 6 7/8”, 7”, 7 1/8”, 7 1/4”,
7 3/8, 7 1/2”, 7 5/8”, 7 3/4”, 7 7/8”,
8”, 8 1/8”, 8 1/4”, 8 3/8”, 8 1/2”,
8 5/8”, 8 3/4”, 9 1/8”, 9 5/8”, 9 3/4”
CHANNEL FRAME
MODEL NO. L10
Description
Model Number
2 hole corner angle (1 5/8 x 2 1/4) l100000eg
CHANNEL FRAME
MODEL NO. EMTC
Description Sizes
Pipe clamp for E.M.T. 3/8”, 1/2”, 3/4”, 1”, 1 1/4”, 1 1/2”, 2
CHANNEL FRAME
MODEL NOS. L18, L19, L20
Description
Model Number
3 hole corner angle 2 1/4” x 3 1/2” l180000eg
3 hole corner angle 1 7/8” x 3 7/8” l190000eg
3 hole corner angle 1 5/8” x 4 1/2” l290000eg
(800) 486-1832 www.trianglefastener.com
116

ERISTRUT®
Description
Description
Description
Description
Description
*for all channel
117
CHANNEL FRAME
MODEL NO. L46
CHANNEL FRAME
MODEL NO. L11
CHANNEL NUTS
MODEL NO. NUT
CHANNEL FRAMING & RELATED PRODUCTS
Sizes
Size
2 hole corner angle 1 7/8 x 2
CHANNEL FRAME
MODEL NO. L21
Angleº
2 hole 7 1/2º, 30º, 45º, 60
Strut nut w/o spring #8*, #10*, 1/4”*, 5/16”*, 3/8”*,
1/2Ӡ, 5/8Ӡ, 3/4Ӡ, 7/8Ӡ
† for a,b,d,e, & m channel
Part Number
4 hole corner angle l220000eg
CHANNEL FRAME
MODEL NO. L47
Angleº
2 hole 30º, 45º, 60º, 82 1/2º
1/2 - 4“ size
Watch for one piece
design with retained
bolt. Also available
in stainless.
3/8”, 5“-12” size
CHANNEL NUTS
MODEL NO. NUTC
Description
Sizes
Strut nut w/o spring for c channel 1/2”, 5/8”, 3/4”, 7/8”
CHANNEL FRAME
MODEL NO. P09
Description
Post base for a channel
CHANNEL FRAME
MODEL NO. P11
Description
Post base for a channel
CHANNEL FRAME
MODEL NO. PCC
Description Sizes
Pipe cushion clamp 1/4”, 3/8”, 1/2”, 3/4”, 1”, 1 1/4”,
1 1/2”, 2”, 2 1/2”, 3”, 3 1/2”, 4”
CHANNEL FRAME
MODEL NO. RIGD
Part Number
p090000eg
Part Number
p110000eg
Description Sizes
Pipe clamp for rigid pipe 3/8”, 1/2”, 1/2” yellow chromate,
3/4”, 3/4” yellow chromate,
1”, 1” yellow chromate,
1 1/4”, 1 1/4” yellow chromate,
1 1/2”, 1 1/2” yellow chromate,
2”, 2” yellow chromate,
2 1/2”, 2 1/2” yellow chromate,
3”, 3” yellow chromate,
3 1/2”, 3 1/2” yellow chromate,
4”, 4” yellow chromate,
5”, 6”, 8”, 10”, 12”
TRIANGLE FASTENER CORPORATION

ERISTRUT®
CHANNEL FRAMING & RELATED PRODUCTS
CHANNEL NUTS
MODEL NO. SPRA
Description
Sizes
Spring nut for a&b channel #8, #10, 1/4”, 5/16”, 3/8”,
7/16”, 1/2”, 5/8”, 3/4”, 7/8”
CHANNEL FRAME
MODEL NO. STR
Description Sizes
1 hole pipe strap 1/4”, 3/8”, 1/2”, 5/8”, 3/4”, 7/8”, 1”
CHANNEL NUTS
MODEL NO. SPRD
Description
Sizes
Spring nut for d & e channel #8, 1/4”, 5/16”, 3/8”,
1/2”, 5/8”, 3/4”
Watch for one piece
design with retained bolt.
CHANNEL FRAME
MODEL NO. UNIV
Description Sizes
Universal pipe clamp 1/2”, 3/4”, 1”, 1 1/4”, 1 1/2”, 2
CHANNEL NUTS
MODEL NO. SPRC
Description
Sizes
Spring nut for c channel #8, 1/4”, 5/16”, 3/8”,
1/2” ,5/8”, 3/4
CHANNEL NUTS
MODEL NO. SPRM
Description
Sizes
Stud spring nut 1/4” 7/8”, 1 1/8”, 1 1/2”,
1 5/8”, 1 7/8”, 2 1/8”
Stud spring nut 3/8” 7/8”, 1 1/8”, 1 5/8”, 1 7/8”, 2 1/8”
Stud spring nut 1/2” 1 1/8”, 1 5/8”, 1 7/8”
Stud spring nut 5/8” 7/8”, 1 1/8”, 1 7/8”, 2 1/8
CHANNEL FRAME
MODEL NO. TCC
Description
CHANNEL FRAME
MODEL NO. TSNC
Description
Sizes
Tube cushion 1/4”, 3/8”, 1/2”, 5/8”, 3/4”, 7/8”, 1”
clamp 1 1/8”, 1 1/4”, 1 3/8”, 1 1/2”, 1 5/8”,
1 3/4”, 1 7/8”, 2”, 2 1/8”,2 3/8”,
2 5/8”, 3 1/8”, 3 5/8”, 4 1/8”
Size
Top spring nut for all channel 1/2
CHANNEL FRAME
MODEL NO. SQNT
Description
Sizes
Square nut 1/4”, 5/16”, 3/8”, 1/2”, 5/8”
CHANNEL FRAME
MODEL NO. TSNT
Description
Sizes
Top spring nut for all channel 1/4, 3/8
Top spring nut 1/2
For A, B, D and M channel
(800) 486-1832 www.trianglefastener.com
118

BEAM CLAMPS
BEAM CLAMP
• Easy installation to beam flanges up to 1/2”.
• Supports 1/4” and 3/8” threaded rod, S-hooks, electrical boxes, conduit and bridle rings.
• Accommodates standard 1/4”-20 or #10-24threaded bridle rings.
Note: When using rigid conduit on P Series, use next size larger clip (1/2” rigid use 12P).
STRAP HANGER CLIPS
• Simple solution for supporting of air duct.
• Accepts wider strap widths up to 1 1/4”.
• The new clips are made from galvanized steel instead of
spring steel. This expands the use to more applications,
especially when used with other plated parts like our
BC2OO beam clamp.
Note: Loads indicated are for CADDY ® fasteners only.
Improved galvanized and plated components for more
demanding environments.
Fig. 1
Fig. 2 Fig. 3 Fig. 4 Fig. 5
Catalog Fig. Flange Load Qty. Per
Number No. Thickness Rating Box
MSS24 1 1/8” to 1/4” 200# 50
MSS58 1 5/16” to 1/2” 200# 50
MSS912 1 9/16” to 3/4” 200#
50
MSR24 2 1/8” to 1/4” 200# 50
MSR58 2 5/16” to 1/2” 200# 50
MSR912 2 9/16” to 3/4” 200#
50
MSSBC200 3 1/8” to 5/8” 100# 50
MSRBC200 4 1/8” to 5/8” 100# 50
MSSCPNA 5 Strap hanger 160# 50
to angle bracket.
Fig. 1
Fig. 2
MOUNTING BRACKET FOR ANY ELECTRIC BOX
• Easily attaches 4” and 4 11/16” outlet
boxes to metal stud.
• Support leg eliminates movement
of box in wall.
• Can be attached to metal or wood stud.
• Offset to eliminate dry wall bulges.
• Delivers compliance with:
NEC Article 300-4(d) when used for
4” and 4 11/16” outlet boxes to
metal or wood studs.
CEC Rule 12-3012 for 4" and 4 11/16”
outlet boxes to metal or wood studs.
Catalog Fig. Box Stud Qty.
Number No. Application Size(s) Depth Per Box
H23 1 U.S. 4” sq. & 4 11/16” 2 1/2” & 3 1/2” 100
H2STC 1 Canada 4” sq. & 4 11/16” 2 1/2” & 3 1/2” 100
H4 1 U.S. 4” sq. & 4 11/16” 4” 50
H6 1 U.S. 4” sq. & 4 11/16” 6” 50
H46TC 1 Canada 4” sq. & 4 11/16” 4” & 6” 100
HS3 2 U.S. & Canada Switch 2 1/2” & 3 1/2” 100
119
TRIANGLE FASTENER CORPORATION

GLOBE
PIPE HANGER PRODUCTS
UNIVERSAL
BEAM CLAMP
Appx. Wt. Maximum
Model Per 100 Recommended Carton
Number Photo Reference (pcs.) Load (lbs.) Quantity
A B C D E F G
103 - 101 3/8" 1" 1 1/2" 1/2" 1" 3/4" 7/8" 33 400 100
104 - 101 1/2" 1 1 1/2" 1/2" 1" 3/4" 7/8" 33 500 100
105 - 101 5/8" 1 1/2" 1 1/2" 1/2 1" 3/4" 1" 22 600 50
106 - 101 3/4" 1 7/8" 1 3/4" 5/8" 1 3/8" 1" 1 1/4" 88 800 50
107 - 101 7/8" 2" 1 3/4" 5/8 1 1/2" 1" 1 1/4" 79 1200 25
Size range: 3/8” through 7/8" rod sizes.
Material: Malleable iron casting with a hardened cup point set screw and lock nut.
Finish: Black. Ordering: Specify rod size, finish and model number.
Approvals: UL Listed for top or bottom of Beam. FM Approved for NFPA 13, maximum rated pipe
size. Complies with Manufacturers Standardization Society SP-69 (Type 19 & 23).
Function: Recommended for attaching hanger rod to top or bottom flange of a beam or bar joist,
where the thickness of a joist or flange does not exceed 3/4”. The open back design
permits rod adjustment.
Installation: Must install in an upright position. Also available in: Electro-Plated Zinc and 304
Stainless Steel.
WIDE THROAT
BEAM CLAMP
Appx. Wt. Maximum
Model Per 100 Recommended Carton
Number Photo Reference (pcs.) Load (lbs.) Quantity
A B C D E F G
113-101 3/8" 1-5/8" 2" 3/4" 1" 1 1/4" 7/8" 28 400 50
114-101 1/2" 1-5/8" 2" 3/4" 1" 1 1/4" 7/8" 34 500 50
115 - 101 5/8" 1 3/4" 2 1/4" 3/4" 1 1/4" 1 1/4" 1" 66 600 50
116 - 101 3/4" 1 7/8" 2 3/8" 3/4" 1 3/8" 1 1/4" 1 1/4" 83 800 50
Size range: 3/8" through 3/4” rod sizes.
Material: Malleable iron casting with a hardened cup point set screw and lock nut.
Finish: Black. Ordering: Specific rod size, finish and model number.
Approvals: UL Listed for top or bottom of Beam. FM Approved for NFPA 13, maximum rated pipe
size. Complies with Manufacturers Standardization Society SP-69 (Type 19 & 23).
Function: Recommended for attaching hanger rod to top or bottom flange of a beam or bar joist
construction. The open back design permits rod adjustment.
Installation: Must install in an upright position. Also available in: Electro-plated zinc.
STEELC-CLAMP
Maximum Appx. Wt.
Model Recommended Per 100 Carton
Number Photo Reference Load (lbs.) (pcs.) Quantity
A B C D E
203 - 100 3/8" 3/8" 2 3/8" 2 5/16" 13/16" 400 41 100
203 - 101 w/locknut 3/8" 3/8" 2 3/8" 2 5/16" 13/16” 400 45 100
204 - 100 1/2" 1/2" 2 3/8" 2 5/16" 13/16” 500 43 100
204 - 101 w/locknut 1/2" 1/2" 2 3/8" 2 5/16" 13/16" 500 46 100
205 - 100 5/8" 5/8" 2 3/8" 2 1/4" 13/16" 550 58 50
205 - 101 w/locknut 5/8" 5/8" 2 3/8” 2 1/4" 13/16" 550 66 50
206 - 100 3/4" 3/4" 2 3/8" 2 1/4" 13/16" 600 80 50
206 - 101 w/locknut 3/4" 3/4" 2 3/8" 2 1/4" 13/16" 600 86 50
207 - 100 7/8" 3/4" 3" 3 1/4" 13/16” 900 168 25
207 - 101 w/locknut 7/8" 3/4" 3" 3 1/4" 13/16” 900 176 25
Size range: 3/8" through 7/8" rod sizes.
Material: Carbon steel with a hardened cup point set screw and available with or without a lock nut.
Finish: Black. Ordering: Specify rod size; finish; and model number.
Approvals: UL Listing and FM Approved for NFPA 13, maximum rated pipe size. Complies with
Federal Specification WW-H 171 E (Type23) and Manufacturers Standardization Society
SP-69 (Type 23).
Function: Designed for structural attachment of hanger rod to bottom flange of a metal beam, purlins,
channel or angle iron. The hanger rod should make contact with the beam flange to ensure
full engagement.
Also available in: Electro plated zinc and 304 stainless steel. Maximum pipe size: 4”.
(800) 486-1832 www.trianglefastener.com
120

BOX AND CONDUIT FASTENERS
BOX SUPPORT
BRACKETS
• Supports either 4" square or 411/16" boxes
• Available for 2 1/2", 3 1/2", 4" and 6" metal studs.
• Attaches with screws to either side of metal stud.
• Brackets may be piggy-backed in series on same side of metal stud.
• Finish: Pre-galvanized
Catalog Metal Box Patent
number stud size Qty. No.
BB4-23 21/2", 31/2" 100 #4757908
BB4-4 4" 100 #4757908
BB4-6 6" 25 #4757908
BB4-XT6 Extends BB3,BB4-23, 100 #4757908
& BB4-4 for use on
6" Deep Studs
Read safety/installation instruction sheets in packages
before use. These products are designed for positioning
only. No load rating.
BOX MOUNTING
BRACKETS
Catalog Stud Box Box
number spacing Depth Qty.
BB2-16 16" 1 1/2” 50
BB2-24 24" 1 1/2” 50
Read safety/installation instruction sheets in packages
before use. These products are designed for positioning
only. No load rating.
• Supports boxes located between studs 16" or 24" on center.
• Adjustable design fits both 1 1/2" and 2 1/8" deep boxes
• Boxes attach early with sheet metal screws through pre-punched holes
• Bar is marked in 1/2" increments.
• Accommodates 4" thru 24" stud spacing using BB2-ac adapters.
• Finish: Pre-galvanized
Catalog Conduit Box Patent
number Size Qty. Number
BG-6 3/8" 100 4958792
BG-8-12 1/2", 3/4" 100
BG-16 1" 100
BG-20 1 1/4" 100
BG-24 1 1/2" 100
BG-32 2" 100
BG-6-4T 3/8" 100 4958792
BG-8-1 2-4T 1/2", 3/4" 100
BG-16-4T 1" 100
• Supports3/8" to 2" conduit.
BG-20-4T 1 1/4" 100
BG-24-4T 1 1/2" 100
• Unique Guide-Rite® Fastener provides for
BG-32-4T 2" 100
fast and easy installation with pliers.
• Available with clearance hole for 1/4" bolt or
Read safety/installation instruction sheets
1/4" -20 thread impression mounting hole.
in packages before use.
• Static Load Capacity: 100 Lbs. - Vertical, 25 Lbs. - Horizontal
STATIC
GUIDE-RITE®
GUIDE-RITE®
LOAD
FASTENER WITH
FASTENER WITH CAPACITY
CLEARANCE HOLE
1/4” 20 THREAD
FOR 1/4" BOLT
IMPRESSION
25 lbs
100 lbs
121
CONDUIT
FASTENERS
TRIANGLE FASTENER CORPORATION

ROD AND WIRE FASTENERS
ROD AND WIRE FASTENERS
• BW2 supports #10-24 or 1/4”-20 threaded bridle rings
and provides easy attachment of electrical boxes
• BW4 supports cables from #12 thru #8 wire
in vertical or horizontal applications.
ROD AND WIRE FASTENERS
Catalog Wire Flange Box
number Size Thickness Qty.
BW2 #12 wire thru 1/8" - 3/8" 100
1/4" plain rod
Catalog
Box
Number Description Qty.
Bw4 Multi-size Wire Fastener 100
Cable Size #12 Wire #10 Wire #8 & 9 Wire
14-2 Cable BW4 BW4 BW4
14-3 Cable BW4 BW4 BW4
12-2 Cable BW4 BW4 BW4
12-3 Cable BW4 BW-8 BW-8
Read safety/installation instruction sheets in packages
before use. These products are designed for positioning
only. No load rating.
Note: An independent means of support is required.
Conduit #10 &#12 #8 & 9 3/16” & 1/8” to 5/16” to 7/16” to
Size Wire Wire 1/4” Rod 1/4” Flange 3/8” Flange 1/2” Flange
1/2" EMT BW-8 BW-8 BW-8 BW-8 BW-12 BW-12
1/2" RIGID BW-8 BW-12 BW-12 BW-12 BW-12 BW-16
3/4" EMT BW-12 BW-12 BW-12 BW-12 BW-16 BW-16
3/4" RIGID BW-12 BW-12 BW-16 BW-16 BW-20* BW-20*
1" EMT --- BW-16 BW-16 BW-16 BW-20* BW-20*
1" RIGID --- --- --- BW-20* BW-20* BW-20*
1 1/4" EMT --- BW-20 BW-20 BW-20 ---
• Attaches conduit to rods or flanges
• Can be used for flexible metallic tubing,
armored cable, portable cable,
control cable, and communication cable.
Catalog Box
Number Qty.
BW-8 100
BW-12 100
BW-16 100
BW-20 100
ELECTRICAL BOX T-BAR FASTENERS
STATIC
LOAD
CAPACITY
Vertical
Flange
*Note: For horizontal applications only.
25 lbs.
Vertical Wire
or Rod
50 lbs.
100 lbs.
Horizontal
Flange
BA12
Catalog
Box
number Description Qty.
BA12 Box Hanger 24" Span 50
BB27 Box Mounting 100
Clip (with Screw)
• Supports 4" octagonal or square boxes
• Allows for flush mounting or 3/4" offset for plaster ring.
• One BB27 box mounting clip with screw
is included with each hanger.
• For additional support attach dropwire
to BB27 Box Mounting tip.
• Warning: Do not use for hanging acoustical tee.
BA27
Box mounting clip (with screw)
(800) 486-1832 www.trianglefastener.com
122

BEAM FASTENERS
TWIST FASTENERS
BA-4-16-W
Catalog Stud Static Box
Number Finish Length Load Cap. Qty.
BA-4-16-W White 5/8" 50lbs. 100
BA-4-WN Black 100lbs. 100
Read safety/installation instruction sheets in packages before use.
BA-4-WN
• Supports electrical fixtures rom 15/16" T-Bar.
• 1/4"-20 stud available in varying lengths
• BA-4-WN wing nut with 1/4" -20 thread impression included.
• No special tools required.
• Without nut add - LN, • Without stud add - LS
FLANGE BEAM FASTENERS
Part Flange Static Box
Number Thickness Load Cap. Qty.
BE-I -2 3/32" To 9/64" 160 Lbs. 100
BE-2-4 1/8" to 1/4" 200 Lbs. 100
BE-5-8 5/16" to 1/2" 200 Lbs. 100
BE-9-12 9/16" to 3/4" 200 Lbs. 100
Read safety/installation instruction sheets in packages before use.
• Permits fast and easy installation on bulb tees and bar joists
• Clearance hole for 1/4" bolt in tab.
• Simply installed with a hammer.
Part Flange Box
Number Thickness Qty.
BU-2-4 1/8" to 1/4" 100
BU-5-8 5/16" to 1/2" 100
BU-9-12 9/16" to 3/4" 100
BU-2-4-S 1/8" to 1/4" 100
BU-5-8-S 5/16" to 1/2" 100
BU-2-4
BU-9-12-S 9/16" to 3/4" 100
• Suspend boxes or fixtures from
STATIC LOAD CAPACITY
beam flanges 1/8" to 3/4" thick.
Note: Indicated loads are static load capacity
• Provided with 1/4”-20 thread
impression for quick
and should not be combined.
and secure attachment.
• Simply installed with a hammer. BU-2-4S
• Available with staked stud
with staked stud
(1/4” - 20 x 3/8”)
123
UNIVERSAL BEAM FASTENERS
Read safety/installation instruction sheets in packages before use.
75 lbs. 100 lbs.
TRIANGLE FASTENER CORPORATION

CONDUIT TO BEAM FASTENERS
CONDUIT TO BEAM FASTENERS
• Supports 3/8" to 2" conduit.
• Unique Guide-Rite® Fastener provides
for fast and easy installation.
• Fasteners will rotate 360 0 .
• Simply installed with a hammer and pliers
STATIC LOAD
CAPACITY
25 lbs.
Part Conduit Flange Box
Number Size Thickness Qty.
BG-6-E-2-4 3/8" 1/8" to 1/4" 100
BG-6-E-5-8 3/8" 5/16" to 1/2" 100
BG-6-E-9-12 3/8" 9/16" to 3/4" 100
BG-8-12-E-2-4 1/2", 3/4" 1/8" to 1/4" 100
BG-8-12-E-5-8 1/2", 3/4" 5/16" to 1/2" 100
BG-8-12-E-9-12 1/2", 3/4" 9/16" to 3/4" 100
BG-16-E-2-4 1” 1/8” to 1/4” 100
BG-16-E-5-8 1” 5/16” to 1/2” 100
BG-16-E-9-12 1” 9/16" to 3/4” 50
Read safety/installation instruction sheets in packages before use.
• Supports 3/8" to 2" conduit.
• Unique Guide-Rite® Fastener provides
for fast and easy installation.
• Fasteners will rotate 360 0 .
• Simply installed with a hammer and pliers
STATIC LOAD
CAPACITY
75 lbs.
Part Conduit Flange Box
Number Size Thickness Qty.
BG-6-U-2-4 3/8" 1/8" to 1/4" 100
BG-6-U-5-8 3/8" 5/16" to 1/2" 100
BG-6-U-9-12 3/8" 9/16" to 3/4" 100
BG-8-12-U-2-4 1/2", 3/4" 1/8" to 1/4" 100
BG-8-12-U-5-8 1/2", 3/4" 5/16" to 1/2" 100
BG-8-12-U-9-12 1/2", 3/4" 9/16" to 3/4" 100
BG-16-U-2-4 1” 1/8” to 1/4” 100
BG-16-U-5-8 1” 5/16” to 1/2” 100
BG-16-U-9-12 1” 9/16" to 3/4” 50
Read safety/installation instruction sheets in packages before use.
BC1
Part Flange Static Load Box
Number Thickness Cap Qty.
BC-1 Thru 1/2” 100 lbs. 100
Read safety/installation instruction sheets in packages before use.
• Fits beam flanges thru 1/2" thick.
• Accepts" S' hooks, 1/4" and 3/8"
threaded rod, 1/4" -20 or #10-24
threaded bridle rings
• Supports conduit and electrical boxes
(800) 486-1832 www.trianglefastener.com
124

STRAP HANGERS AND BRIDLE RINGS
STRAP HANGERS
PARALLEL
Part Flange Box
Number Description Thickness Qty.
BH-2-4 Parallel 1/8" to 1/4" 100
BH-5-8 Parallel 5/16" to 1/2" 100
BH-2-4-R Right Angle 1/8" to 1/4" 100
BH-5-8-R Right Angle 5/16" to 1/2" 100
Read safety/installation instruction sheets in packages before use.
• Suspend straps thru 1" wide from
beam flanges 1/8" to 3/4" thick.
• Suspend from straps parallel
or at right angles to beams
• Simply installed with a hammer.
• Static Load Capacity: 200 Lbs.
RIGHT ANGLE
Part Ring Thread Box
Number Size Size Qty.
BR-8-T 1/2" #10-24 100
BR-12-T 3/4" #10-24 100
BR-20-T 1 1/4" #10-24 100
BR-32-T 2" #10-24 100
BR-20-4T 1 1/4" 1/4"-20 100
BR-32-4T 2" 1/4"-20 100
THREADED
BR-64-4T 4" 1/4"-20 50
BR-16-3W 1" 3/16" 100
BR-24-4W 1 1/2" 1/4" 100
• Supports low voltage communication
BR-8 1/2" #10-24 100
cables from beams or rods when
BR-12 3/4" #10-24 100
used with other fasteners
BR-20 1 1/4" #10-24 100
BR-32 2" #10-24 100
• Ultimate Static Load Capacity: 50 Lb&
• Finish: Zinc Rated
LAG SCREW
FOR WOOD
BEAMS
UNTHREADED
125
THREADED BRIDLE RINGS
Read safety/installation instruction sheets in packages before use.
TRIANGLE FASTENER CORPORATION

VULCAN
THREADED ROD PRODUCTS
THREADED ROD - CARBON STEEL
THREADED ROD - CARBON STEEL
National coarse (USS)
Size Wt Per 100’ Pcs per bundle
1/4-20 11.9 50
5/16-18 19.3 35
3/8-16 28.4 25
7/16-14 39.6 17
1/2-13 51.2 12
9/16-12 67.0 10
5/8-11 83.1 8
3/4-10 121.7 5
7/8-9 167.5 4
1-8 219.0 2
1 1/8-7 280.5 1
1 1/4-7 350.0 1
1 3/8-6 417.2 1
1 1/2-6 504.7 1
1 3/4-5 690.0 1
2-4 1/2 904.0 1
2 1/4 –4 1/2 1180.0 1
2 1/2-4 1460.0 1
Finishes: plain oil or zinc
Stock lengths:
Right hand threads-2', 3' 6', 10', 12'
Left hand threads-3', 6', 12'
STOCK ANCHOR
BOLTS-BULK
Size Approx. Approx. pcs.
Wt. Per 100’ per drum
3/8x6x1x1 1/2 18 4500
8 22 3150
10 26 2500
12 30 1675
1/2x6x1x2 32 3200
8 41 2500
10 49 1600
12 58 1400
14 67 1200
16 75 1100
18 84 1000
5/8x6x2x4 56 1750
8 69 1500
10 83 1200
12 96 900
14 110 700
16 124 600
18 138 500
3/4x8x3x4 114 950
10 135 700
12 156 500
14 177 450
15 187 400
16 197 350
18 218 250
20 237 250
24 281 225
30 344 200
7/8x12x3x6 206 500
14 233 400
15 247 375
16 261 350
18 288 300
20 316 175
24 371 150
30 453 125
1x12x3x6 281 350
14 318 300
15 337 275
16 356 250
18 393 225
20 431 200
24 506 150
30 618 125
36 731 100
Plain and hot galvanized*
Zinc and stainless available upon request
approx. Wt
dimensions per 100
pipe size d c l t (low carbon)
1/2” 1/4” 1 5/16 3 1/4 2 3/8 7.4
3/4” 1/4” 1 1/8 3 5/16 2 3/8 7.7
1” 1/4” 1 3/8 3 7/16 2 3/8 8.1
1/3” 3/8” 1 5/16 3 1/4 2 3/8 19.0
3/4” 3/8” 1 1/8 3 5/16 2 3/8 19.7
1” 3/8” 1 3/8 3 7/16 2 3/8 21.0
1 1/4” 3/8” 1 11/16 3 3/4 2 3/8 22.5
1 1/2” 3/8” 2 4 2 1/2 24.3
2” 3/8” 2 7/16 4 1/2 2 1/2 27.3
2 1/2” 1/2” 2 15/16 5 1/4 3 57.3
3” 1/2” 3 9/16 5 13/16 3 63.5
3 1/2” 1/2” 4 1/16 6 5/16 3 69.4
4” 1/2” 4 9/16 6 13/16 3 74.9
5” 1/2” 5 5/8 7 13/16 3 86.7
6” 5/8” 6 3/4 9 1/2 3 3/4 162.0
8” 5/8” 8 3/4 11 1/2 3 3/4 200.4
10” 3/4” 10 7/8 13 13/16 4 364.6
12” 7/8” 12 7/8 16 1/16 4 1/4 561.7
14” 7/8” 14 1/8 17 5/16 4 1/4 618.8
16” 7/8” 16 1/8 19 5/16 4 1/4 676.6
18” 1” 18 1/8 21 11/16 4 3/4 1040.0
20” 1” 20 1/8 23 11/16 4 3/4 1130.0
24” 1” 24 1/8 27 11/16 4 3/4 1330.0
30” 1” 30 1/8 33 11/16 4 3/4 1620.0
36” 1” 36 1/8 39 11/16 4 3/4 1900.0
Finishes: plain, zinc, and hot-dip galvanized
Stainless steel available upon request
*hdg u-bolts furnished with 2 nuts assembled
Other standard and special u-bolts available upon request.
TYPE 137 STANDARD
PIPE SIZE U-BOLTS
(DxLxCxT)
(800) 486-1832 www.trianglefastener.com
126

PRODUCT SPECIFICATIONS
Diameter
3/16'' and 1/4''
Thread Form
Original notched Hi-Lo®
Point Type
Nail
Finish
Blue Climaseal®
PERFORMANCE DATA
Anchor Depth of Embedment in Solid Material
(inches)
Diameter 1'' 1-1/4'' 1-1/2'' 1-3/4''
3/16'' 341lbs. 581 lbs. 863 lbs. 1059 lbs.
1/4'' 718 lbs. 1138 lbs. 1537 lbs. 1860 lbs.
PULLOUT IN HOLLOW BLOCK
Anchor Depth of Embedment in Solid Material
(inches)
Diameter 1'' 1-1/4'' 1-1/2'' 1-3/4''
3/16'' 209 lbs. 357 lbs. 468 lbs. 547 lbs.
1/4'' 406 lbs. 615 lbs. 851 lbs. 984 lbs.
Shear Strength Shear Strength
Anchor Anchor 314 PSI Hard Lightweight
Diameter Embedment Rock Concrete Hollow Block
3/16” 1 1/4” 852 lbs. 731 lbs.
1/4” 1 1/4” 1604 lbs. 1058 lbs.
TEST NUMBER CH3932/PITTSBURGH TESTING LABORATORIES
127
TAPCON MASONRY ANCHORS
PULLOUT IN CONCRETE
(3145 PSI, CURED 40 DAYS) (LBS)
TEST NUMBER CH3932/PITTSBURGH TESTING LABORATORIES
TEST NUMBER CH3748/PITTSBURGH TESTING LABORATORIES
SHEAR STRENGTH
TAPCON
THE ORIGINAL MASONRY FASTENING SYSTEM
The original masonry anchor that cuts threads into concrete, brick or hollow block.
APPLICATIONS
• Electrical junction boxes
and conduit clips to masonry.
• Wood headers and furring
strips to masonry.
• HVAC strapping to masonry.
• Plywood backer boards to masonry.
• Exterior insulation systems to masonry.
CORROSION RESISTANCE
Kesternich Results (DIN 50018, 2.0L)
• 30 Cycles - 10% or less red rust
Salt Spray Results (ASTM B117)
• 720 Hours - 10% or less red rust
ACQ Treated Lumber
HEAD STYLES
SELECTOR GUIDE
Description Drill Bit Fixture Thickness
3/16 x 1-1/4'' 5/32 x 3-1/2" 0 - 1/4"
1/4 x 1-1/4" 3/16 x 3-1/2" 0 - 1/4"
3/16 x 1-3/4" 5/32 x 3-1/2" 1/4 - 3/4"
1/4 x 1-3/4" 3/16 x 3-1/2" 1/4 - 3/4"
3/16 x 2-1/4" 5/32 x 4-1/2" 3/4" - 1-1/4"
1/4 x 2-1/4" 3/16 x 4-1/2" 3/4" - 1-1/4"
3/16 x 2-3/4" 5/32 x 4-1/2" 1-1/4" - 1-3/4"
1/4 x 2-3/4" 3/16 x 4-1/2" 1-1/4" - 1-3/4"
3/16 x 3-1/4" 5/32 x 5-1/2" 1-3/4" - 2-1/4"
1/4 x 3-1/4" 3/16 x 5-1/2" 1-3/4" - 2-1/4"
3/16 x 3-3/4" 5/32 x 5-1/2" 2-1/4" - 2-3/4”
1/4 x 3-3/4" 3/16 x 5-1/2" 2-1/4" - 2-3/4"
3/16 x 4" 5/32 x 5-1/2" 2-1/2" - 3"
1/4 x 4" 3/16 x 5-1/2" 2-1/2" - 3"
1/4 x 5" 3/16 x 6-1/2" 3-1/4" - 4"
1/4 x 6" 3/16 x 7-1/2" 4-1/4" - 5"
Condrive 500® For 3/16 and 1/4 diameter,
Hex and Flat Heads, lengths up to 3-3/4"
Condrive 1000® For 3/16 and 1/4 diameter,
Hex and Flat Heads, lengths up to 3-3/4"
Condrive 2000® For 3/16 and 1/4 diameter,
Hex Head, lengths up to 2-3/4"
The minimum embedment requirement is 1" and the maximum
embedment is 1-3/4".
One drill bit is provided with every box of 100 pieces.
*SDS with Hex Drill Bits:
5/32" x 7" SDS Rotary Hammer Drill Bit, Part Number 3311910;
(*Condrive 1000 Only)
3/16" x 7" SDS Rotary Hammer Drill Bit, Part Number 3101910.
Hex Washer Head
3/16'' Diameter: 1/4'' slotted
hex washer head (HWH)
1/4'' Diameter: 5/16'' slotted
hex washer head (HWH)
Flat Countersunk for Wood
3/16'' Diameter: #2 phillips flat
head (PFH)
1/4'' Diameter: #3 phillips flat
head (PFH)
Tapcon is a registered trademark of ITW Buildex
TRIANGLE FASTENER CORPORATION

410 STAINLESS STEEL TAPCON
410 STAINLESS STEEL TAPCON
MASONRY FASTENING SYSTEM
Premium masonry anchor that provides the corrosion protection of 410
Stainless Steel and the performance of our original carbon Tapcon®.
APPLICATIONS
• Shutters - protective and decorative
• Windows
• Screened porch and pool enclosures
• Railings - safety and decorative
• Exterior fixtures
• Marine
• Agricultural
PRODUCT SPECIFICATIONS
Diameter 1/4’’
Thread Form Original Notched Hi-Lo®
Point Type Nail
Material 410 Stainless Steel
Finish ClimaShield
CORROSION RESISTANCE
Salt Spray Results (ASTM B117)
• 1600 Hours - NO RED RUST.
PERFORMANCE DATA
PULLOUT IN CONCRETE
(3145 PSI, CURED 40 DAYS) (LBS)
Anchor Depth of Embedment in Solid Material (inches)
Diameter 1” 1-1/4” 1-1/2” 1-3/4”
1/4” 1381 lbs. 1616 lbs. 2041 lbs. 2332 lbs.
PULLOUT IN HOLLOW BLOCK
Anchor Depth of Embedment in Solid Material
(inches)
Diameter 1-1/4”
1/4” 754 lbs.
SHEAR STRENGTH
Shear Strength Shear Strength
Anchor Anchor 314 PSI Hard Lightweight
Diameter Embedment Rock Concrete Hollow Block
1/4” 1 1/4” 1622lbs. 1218 lbs.
SELECTOR GUIDE
Description Drill Bit Fixture Thickness
1/4 x 1-1/4'' 3/16 x 3-1/2'' 0-1/4''
1/4 x 1-3/4'' 3/16 x 3-1/2'' 1/4-3/4''
1/4 x 2-1/4'' 3/16 x 4-1/2'' 3/4-1-1/4''
1/4 x 2-3/4'' 3/16 x4-1/2'' 1-1/4''-1-3/4''
1/4 x 3-1/4'' 3/16 x 5-1/2'' 1-3/4''-2-1/4''
1/4 x 3-3/4'' 3/16 x 5-1/2'' 2-1/4''-2-3/4''
Condrive 500® For 3/16 and 1/4 diameter,
Hex and Flat Heads, lengths up to 3-3/4"
Condrive 1000® For 3/16 and 1/4 diameter,
Hex and Flat Heads, lengths up to 3-3/4"
Condrive 2000® For 3/16 and 1/4 diameter,
Hex Head, lengths up to 2-3/4"
HEAD STYLES
HWH
5/16'' Hex Washer Head
Note: Designated holding power depends on the quality of the masonry
material, depth of embedment and proper hole size. These figures are offered
only as a guide and are not guaranteed in any way by Illinois Tool Works Inc.
The figures indicate average ultimate pull-out and shear failure values. A safety
factor of 4:1 or 25% of ultimate pull-out value is generally accepted as a safe
working load. However, reference should always be made to applicable codes
for the specific safe working ratio. All values are based on close tolerance
holes drilled with Buildex Tapcon® carbide drill bits. Performance of the Tapcon
anchor may vary in extremely hard concrete aggregates. Consult your Buildex
representative for further information.
PFH
#3 Phillips Flat Head
As in the case with all applications, Buildex can only suggest typical fasteners
for typical applications and that the connection design is the sole responsibility
of the Building Design Engineer, Architect or otherwise responsible person
charged with the design of the connection.
Tapcon®, Condrive 500®, Hi-Lo®, Condrive 1000®,
Condrive 2000®, Climaseal® and Building Ideas That Work®
are trademarks of ITW Buildex and Illinois Tool Works Inc.
(800) 486-1832 www.trianglefastener.com
128

MAXI-SET TAPCON
MAXI-SET TAPCON®
MASONRY FASTENING SYSTEM
For Tapcon® applications that require more
anchor bearing surface.
APPLICATIONS
• Shutters - protective and decorative.
• Screened porch and pool enclosures.
• Various sheet metal flashings.
• Decorative wrought iron.
• Wood nailers and plywood attachment.
HEAD STYLES
5/16" across flats hex with
5/8" diameter flange.
CORROSION RESISTANCE
Salt Spray Results (ASTM B117)
• 1100 Hours - 10% or less red rust
PRODUCT SPECIFICATIONS
Diameter . . . . . . 1/4"
Thread Form. . . Original notched Hi-Lo®
Point Type. . . . . Nail
Finish . . . . . . . . UltraShield or White UltraShield
SELECTOR GUIDE
PERFORMANCE DATA
PULLOUT IN CONCRETE
(3145 PSI, CURED 40 DAYS)
Anchor Depth of Embedment
Diameter in Solid Material (inches)
1'' 1-1/4'' 1-1/2'' 1-3/4''
1/4'' 718 lbs. 1138 lbs. 1537 lbs. 1860 lbs.
PULLOUT IN HOLLOW BLOCK
(3145 PSI, CURED 40 DAYS)
Anchor Depth of Embedment
Diameter in Solid Material (inches)
1'' 1-1/4'' 1-1/2'' 1-3/4''
1/4'' 718 lbs. 1138 lbs. 1537 lbs. 1860 lbs.
PULLOUT IN HOLLOW BLOCK
(3145 PSI, CURED 40 DAYS)
Shear Shear
Strength Strength
Anchor Anchor 3145 Hollow
DiameterEmbedment PSi Hard Bock
1/4'' 1 1/4'' 1604 lbs. 1058 lbs.
Anchor Anchor Box Drill Bit Anchor
Description Part Number Quantity Drill Bit Part Number Finish
1/4 x 1-3/4" 3294000 1,000 3/16 x 3-1/2 3098910 UltraShield
1/4 x 2-1/4" 3295000 1,000 3/16 x 4-1/2 3099910 UltraShield
1/4 x 2-3/4" 3364000 1,000 3/16 x 4-1/2 3099910 UltraShield
1/4 x 3-1/4" 3365000 750 3/16 x 5-1/2' 3100910 UltraShield
1/4 x 1-3/4” 3383100 1,000 3/16 x 3-1/2' 3098910 White UltraShield
1/4 x 2-1/4" 3384100 1,000 3/16 x 4-1/2' 3099910 White UltraShield
1/4 x 2-3/4” 3408100 1,000 3/16 x 4-1/2" 3099910 White UltraShield
1/4 x 3-1/4" 3409100 750 3/16 x 5-1/2" 3100910 White UltraShield
White UltraShield Available with bronze painted head over White UltraShield
Note: Indicated pull-out and shear failure values were obtained in tests
witnessed by Pittsburgh Testing Laboratory personnel. Designated holding
power depends on the quality of the masonry material, depth of embedment and
proper hole size. These figures are offered only as a guide and are not
guaranteed in any way by Illinois Tool Works Inc. The figures indicate average
ultimate pull-out and shear failure values. A safety factor of 4:1 or 25% of
ultimate pull-out value is generally accepted as a safe working load. However,
reference should always be made to applicable codes for the specific safe
working ratio. All values are based on close tolerance holes drilled with Buildex
Tapcon® carbide drill bits. Performance of the Tapcon anchor may vary in
extremely hard concrete aggregates.
INSTALLATION TOOLS
• Condrive 500® - Compact high speed installation tool designed for installation
of Tapcon hex head and Phillips flat head anchors up to 3-3/4'' long.
• Condrive 1000® - A multi-purpose tool designed for installation of Tapcon hex
head and Phillips flat head anchors up to 3-3/4'' long.
• Condrive 2000® - A highly-automated, high speed, one- step tool designed
specifically for repetitive installation of hex head Tapcon anchors of
lengths up thru 2-3/4''.
• Buildex Condrive Tools are designed to specifically install Tapcon Anchors
and to fit standard hammer drills.
129
TRIANGLE FASTENER CORPORATION

LARGE DIAMETER TAPCON (LDT)
WEDGE-BOLT ® by POWERS
Refer to Page 177 for more information on Wedge-Bolt!
The Wedge-Bolt ® is a one piece heavy duty
anchor with either a finished hex head or
countersunk Phillips flat head. It is easy to
identify, removable and vibration-resistant.
Base Material: Concrete, Block, Brick, Stone
Size Range: 3/16” x 1-1/4” to 3/4” x 8”
Anchor Material: Heat Treated, High
Strength Carbon Steel
HEX HEAD WEDGE-BOLT® ANCHORS
Std. Std.
Size Box Ctn.
3/16” x 1-1/4” 100 500
3/16” x 1-3/4” 100 500
3/16” x 2-1/4” 100 500
3/16” x 2-3/4” 100 500
1/4” x 1-1/4” 100 500
1/4” x 1-3/4” 100 500
1/4” x 2-1/4” 100 500
1/4” x 3” 100 500
3/8” x 1-3/4” 50 250
3/8” x 2-1/2” 50 250
3/8” x 3” 50 250
3/8” x 4” 50 250
1/2” x 2” 50 200
1/2” x 2-1/2” 50 200
1/2” x 3” 50 150
1/2” x 4” 50 150
1/2” x 5” 50 100
1/2” x 6” 25 75
5/8” x 3” 25 100
5/8” x 4” 25 100
5/8” x 5” 25 75
5/8” x 6” 25 75
3/4” x 3” 20 60
3/4” x 4” 20 60
3/4” x 5” 20 60
3/4” x 6” 20 60
3/4” x 8” 10 40
* The published length is measured from below the hex
washer head to the end of the anchor.
PHILLIPS FLAT HEAD
WEDGE-BOLT® ANCHORS
Std. Std.
Size Box Ctn.
3/16” x 1-1/4” 100 500
3/16” x 1-3/4” 100 500
3/16” x 2-1/4” 100 500
3/16” x 2-3/4” 100 500
* The published length is the overall length of the anchor
Note: Indicated pull-out and shear failure values were obtained in tests witnessed by
Pittsburgh Testing Laboratory personnel. Designated holding power depends on the quality
of the masonry material, depth of embedment and proper hole size. These figures are
offered only as a guide and are not guaranteed in any way by Illinois Tool Works Inc. The
figures indicate average ultimate pull-out and shear failure values. A safety factor of 4:1 or
25% of ultimate pull-out value is generally accepted as a safe working load. However,
reference should always be made to applicable codes for the specific safe working ratio. All
values are based on close tolerance holes drilled with RED HEAD Tapcon® carbide drill bits.
Performance of the Tapcon anchor may vary in extremely hard concrete aggregates.
As in the case with all applications, RED HEAD can only suggest typical fasteners for typical
applications and that the connection design is the sole responsibility of the Building Design
Engineer, Architect or otherwise responsible person charged with the design of the
connection.
(800) 486-1832 www.trianglefastener.com
130

TYPES OF ANCHORS
CONCRETE FASTENING SYSTEMS
THE INSIDE STORY ABOUT MECHANICAL AND ADHESIVE ANCHORS
EXPANSION TYPE
Tension loads are transferred to the base material through a portion of the anchor that
is expanded inside the drill hole.
Examples: Red Head Redi-Bolts, Dynabolts, Multi-Set II
Anchors and Hammer-Sets.
ADHESIVE TYPE
Resistance to tension loads is provided by the presence of an adhesive
between the threaded rod (or rebar) and the inside walls of the drill hole.
Examples: Epcon A7, C6, G5, Maxima 7 Capsules and
Impact Capsules
KEYING TYPE
Holding strength comes from a portion of an anchor that is expanded into a
hollow space in a base material that contains voids such as concrete block or
brick.
Examples: Epcon adhesives used in screen tubes or
umbrella insert
FRICTION TYPE
Load capacity is created by driving a fastener into a pre-drilled hole that is
slightly smaller than the fastener itself.
Examples: Redi-Drives
MECHANICAL
INTERLOCKING TYPE
Tension loads are resisted by threads on the fastener engaging with threads
cut into the base material.
Examples: LDT, Tapcon and E-Z Ancors
131
TRIANGLE FASTENER CORPORATION

CONCRETE FASTENING SYSTEMS
MODES OF FAILURE
When anchors are loaded to their maximum capacity, several different types (modes) of failure are possible depending on the type of anchor,
strength of the base material, embedment depth, location of the anchor, etc. Common modes of failure include:
CONCRETE SPILL CONE
Occurs at shallow embedments where the resistance of the base material
is less than the resistance of the anchor and the base material fails.
STEEL BREAKAGE
The capacity of the anchorage exceeds the strength of the steel anchor or rod
material.
ANCHOR PULLOUT
Base material adjacent to the extension portion of an anchor crushes,
resulting in the anchor pulling out of the hole until the capacity of the spill
cone is reached, at which point the concrete will spill. This type of failure
happens more commonly when anchors are set with deep embedment
depths.
BOND FAILURE
Shear failure of the adhesive at rod adhesive interface or adhesive-base
material interface. Occurs more commonly in deep embedments using
high strength steel rods.
EDGE DISTANCE AND SPACING REDUCTION
Reduces the holding values, when anchors are placed too close to the edge.
This also occurs when two or more anchors are spaced closely together. See
suggested edge distance, anchor spacing distances and reduction values in
the product sections.
(800) 486-1832 www.trianglefastener.com
132

REDI-BOLT ® ANCHORS
REDI-BOLT ® ANCHORS
Reduces Cost, Increases Safety and Improves Anchoring Performance
DESCRIPTION/SUGGESTED SPECIFICATIONS:
HEAVY DUTY SLEEVE ANCHORS
Specified for anchorage into solid concrete and concrete fill.
The Redi-Bolt features a patented double expansion sleeve, Grade 5, high strength threaded bolt, a steel expander cone
and washer. The exposed end of the anchor is stamped by Red Head to identify anchor length post-installation. Anchors
should be installed with carbide type drill bits made in accordance to ANSI B212.15-1994.
ADVANTAGES:
Redi-Bolt provides up to 22% more pullout and up to 48% more shear than wedge anchors; up to 40% more pullout and
61% more shear than traditional sleeve anchors. This means reduced costs because with higher tension and shear values
you can:
• Use a smaller diameter anchor
• Use a smaller, less expensive drill bit
• Drill faster because of smaller hole and shallower embedment
• Threaded bolt can be removed and reinstalled into expansion assembly
VIBRATION RESISTANCE
Ontario Hydro Test Report Findings: 1/2" Redi-Bolt anchor withstood two million
dynamic load cycles with no indication of slip or unusual change.
APPROVALS/LISTINGS
• Meets or exceeds U.S. Government G.S.A. specification FF-S-325 Group II, Type 3, Class 1
• Ontario Hydro Vibration Test
• Data for seismic conditions tested to ICBO criteria by ICBO lab
INSTALLATION STEPS
• Select a carbide drill bit
with a diameter equal to
the anchor diameter. Drill
hole to any depth
exceeding the desired
embedment (see chart for
recommended
embedment).
• Clean hole or continue
drilling additional depth to
accommodate drill fines
(concrete dust).
• Drive the anchor into the
hole through material
being fastened until
washer is flush with
material.
• Expand Redi-Bolt by
tightening the anchor 3 to
5 turns, or to the specified
torque requirements (see
installation instructions).
133
TRIANGLE FASTENER CORPORATION

REDI-BOLT ®
ANCHORS
REDI-BOLT ® ANCHORS
Reduces Cost, Increases Safety and Improves Anchoring Performance
Technical Data
REDI-BOLT REMOVABLE ANCHORS SELECTION CHART
ANCHOR MINIMUM MaxIMUM Qty/wt
DRILL Anchor EMBEDMENT FIXTURE INSTALLATION Qty/Wt per master
DIAMETER LENGTH IN CONCRETE THICKNESS Length ID Code per box carton
In. (mm) In. (mm) In. (mm) In. (mm) Ft. Lbs. (Nm) letter lbs. lbs.
3/8 (9.5) 2 (50.8) 1-1/2 (38.1) 1/2 (12.7) 35 (47.5) B 50/3.7 400/30
3/8 (9.5) 3 (75.2) 2 (50.8) 1 (25.4) 35 (47.5) D 50/5.4 400/44
1/2 (12.7) 3-3/4 (95.3) 2-1/2 (63.5) 1-1/4 (31.8) 60 (81.4) E 25/5.9 200/48
1/2 (12.7) 4-3/4 (120.7) 2-1/2 (63.5) 2-1/4 (57.2) 60 (81.4) G 25/6.4 200/56
1/2 (12.7) 5-3/4 (146.5) 2-1/2 (63.5) 3-1/4 (82.6) 60 (81.4) I 25/8.2 200/66
5/8 (15.9) 4 (101.6) 2-3/4 (69.9) 1-1/4 (31.8) 100 (135.7) F 15/6.6 150/67
5/8 (15.9) 5 (127.0) 2-3/4 (69.9) 2-1/4 (57.2) 100 (135.7) H 15/7.9 150/80
5/8 (15.9) 6 (152.4) 2-3/4 (69.9) 3-1/4 (82.6) 100 (135.7) J 10/6.1 150/31
3/4 (19.1) 4-1/4 (108.0) 3 (75.2) 1-1/4 (31.8) 120 (162.8) F 10/6.3 50/32
3/4 (19.1) 5-1/4 (133.4) 3 (75.2) 2-1/4 (57.2) 120 (162.8) H 10/7.5 50/38
3/4 (19.1) 7-1/4 (184.2) 3 (75.2) 4-1/4 (108.0) 120 (162.8) L 5/5.0 50/50
* Grade 2 Hollow Block Anchor
RECOMMENDED SPACING AND EDGE DISTANCE REQUIREMENTS FOR TENSION LOADS
Min. Allowable
Min. Allowable
Edge Distance Edge DIstance At Spacing Required Spacing Between Anchors
Anchor Installation Required To Obtain Which The Load Factor To Obtain Max. Load Factor
Dia. Torque Max. Working Load Applied = 0.75 Working Load Applied = 0.50
In. (mm) Ft. Lbs. (Nm) In. (mm) In. (mm) In. (mm) In. (mm)
3/8 (9.5) 35 (47.5) 3-3/4 (95.3) 1-7/8 (47.6) 4-1/2 (114.3) 1-7/8 (47.6)
1/2 (12.7) 60 (81.4) 5 (127.0) 2-1/2 (63.5) 6 (152.4) 2-1/2 (63.5)
5/8 (15.9) 100 (135.7) 6-1/4 (158.8) 3-1/8 (79.4) 7-1/2 (190.5) 3-1/8 (79.4)
3/4 (19.1) 120 (162.8) 7-1/2 (190.5) 3-3/4 (95.3) 9 (228.6) 3-3/4 (95.3)
Linear interpolation may be used for intermediate spacing and edge distances.
ULTIMATE SHEAR AND TENSION VALUES (LBS/KN) IN 4000 PSI (27.6 MPA) CONCRETE
Anchor
Dia. Embedment Installation Torque Ultimate Tension Ultimate Shear
In. (mm) In. (mm) Ft. Lbs. (Nm) Lbs. (kN) Lbs. (kN)
3/8 (9.5) 2 (50.8) 35 (47.5) 5,195 (23.1) 7,730 (34.4)
2-1/2 (63.5) 5,870 (26.1) 8,018 (35.7)
1/2 (12.7) 2-1/2 (63.5) 60 (81.4) 6,931 (30.8) 10,132 (45.1)
4 (101.6) 10,518 (46.8) 13,005 (57.9)
5/8 (15.9) 2-3/4 (69.9) 100 (135.7) 8,585 (38.2) 13,484 (60.0)
5 (127.0) 19,219 (85.5) 21,040 (93.6)
3/4 (19.1) 3 (76.2) 120 (162.8) 10,574 (47.0) 18,733 (83.3)
6 (152.4) 20,267 (90.2) 29,668 (132.0)
Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.
ULTIMATE SHEAR AND TENSION VALUES (LBS/KN) IN C90 GROUT-FILLED CMU
Anchor
Dia. Embedment Installation Torque Ultimate Tension Ultimate Shear
In. (mm) In. (mm) Ft. Lbs. (Nm) Lbs. (kN) Lbs. (kN)
3/8 (9.5) 2 (50.8) 20 (27.1) 3,798 (16.9) 4,855 (21.6)
2-1/2 (63.5) 3,896 (17.3) 4,855 (21.6)
1/2 (12.7) 2-1/2 (63.5) 35 (47.5) 3,993 (17.8) 6,867 (30.5)
4 (101.6) 4,182 (18.6) 6,867 (30.5)
5/8 (15.9) 2-3/4 (69.9) 60 (81.4) 3.990 (17.7) 11,777 (52.4)
5 (127.0) 4,634 (20.5) 12,525 (93.6)
3/4 (19.1) 3 (76.2) 85 (115.3) 4,693 (20.9) 18,733 (55.7)
6 (152.4) 5,908 (26.3) 13,964 (62.1)
Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.
(800) 486-1832 www.trianglefastener.com
134

DYNABOLT® SLEEVE ANCHORS
DYNABOLT ® SLEEVE ANCHORS
VERSATILE HEAVY-DUTY SLEEVE ANCHORS
DESCRIPTION/SUGGESTED SPECIFICATIONS
SLEEVE TYPE ANCHORS—
specified for anchorage into concrete, masonry, grout filled block and hollow block
Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and
washer.
Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.
Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994.
Anchors are tested to ASTM E488 criteria.
APPROVALS/LISTINGS
Meets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group II,
Type 3, Class 3
Factory Mutual
SBCCI Compliance Report – #9570
California State Fire Marshal
INSTALLATION STEPS
1. Use a bit with a diameter equal to the
anchor. See selection chart to
determine proper size bit for anchor
used. Drill hole to any depth exceeding
minimum embedment. Clean hole.
2. Insert assembled anchor into
hole, so that washer or head
is flush with materials to be
fastened.
3. Expand anchor by tightening
nut or head 2 to 3 turns.
135
TRIANGLE FASTENER CORPORATION

DYNABOLT® SLEEVE ANCHORS
DYNABOLT ® SLEEVE ANCHORS
VERSATILE HEAVY-DUTY SLEEVE ANCHORS
Sizes
DYNABOLT CARBON STEEL
Anchor
Max.
Dia. & Thickness Qty/Wt
Drill Effective of Material Per
Bit Size Anchor Bolt Dia./ Minimum to be Qty/Wt Master
Head (Threads) Length* Threads Embedment Fastened Per Box Carton
Style Per Inch In. (mm) Per Inch In. (mm) In. (mm) Lbs. Lbs.
Acorn Nut 1/4” - 20 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.9 1000/ 20 ⌧
1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.6 1000/ 27 ⌧ ⌧
2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.7 1000/ 38 ⌧
Hex Nut 1/4" - 20 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.6 1000/ 17 ⌧
1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.3 1000/ 24 ⌧
2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.4 1000/ 35 ⌧
5/16" - 18 1-1/2 (38.1) 1/4" /20 1-1/4 (31.8) 1/4 (6.4) 100/ 4.0 1000/ 41 ⌧
2-1/2 (63.5) 1/4" /20 1-1/4 (31.8) 1-1/4 (31.8) 100/ 5.9 800/ 47 ⌧
3/8" - 16 1-7/8 (47.6) 5/16" /18 1-1/2 (38.1) 3/8 (9.5) 50/ 3.5 500/ 36 ⌧ ⌧
3 (76.2) 5/16" /18 1-1/2 (38.1) 1-1/2 (38.1) 50/ 4.9 400/ 40 ⌧ ⌧
1/2" - 13 2-1/4 (57.2) 3/8" /16 1-7/8 (47.6) 3/8 (9.5) 25/ 3.3 250/ 34 ⌧ ⌧
3 (76.2) 3/8" /16 1-7/8 (47.6) 1-1/8 (28.6) 25/ 4.0 200/ 33 ⌧ ⌧
4 (101.6) 3/8" /16 1-7/8 (47.6) 2-1/8 (54.0) 25/ 5.3 200/ 44 ⌧ ⌧
5/8" - 11 2-1/4 (57.2) 1/2" /13 2 (50.8) 1/4 (6.4) 25/ 6.3 150/ 38 ⌧
3 (76.2) 1/2" /13 2 (50.8) 1 (25.4) 25/ 7.0 150/ 46 ⌧
4-1/4 (108.0) 1/2" /13 2 (50.8) 2-1/4 (57.2) 10/ 3.9 100/ 41 ⌧ ⌧
6 (152.4) 1/2" /13 2 (50.8) 4 (101.6) 10/ 4.9 50/ 25 ⌧
3/4" - 10 2-1/2 (63.5) 5/8" /11 2-1/4 (57.2) 1/4 (6.4) 10/ 4.7 50/ 25 ⌧
4 (101.6) 5/8" /11 2-1/4 (57.2) 1-3/4 (44.5) 5/ 3.2 50/ 33 ⌧
6-1/4 (158.8) 5/8" /11 2-1/4 (57.2) 4 (101.6) 5/ 4.3 50/ 44 ⌧
Phillips 1/4" - 20 1-1/2 (38.1) 3/16" /24 1-1/8 (28.6) 3/8 (9.5) 100/ 1.9 1000/ 21 ⌧
Flat Head (head dia. .477) 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 2.7 1000/ 28 ⌧ ⌧
3-1/8 (79.4) 3/16" /24 1-1/8 (28.6) 2 (50.8) 100/ 3.8 1000/ 38 ⌧ ⌧
4 (101.6) 3/16" /24 1-1/8 (28.6) 2-7/8 (73.0) 100/ 4.7 1000/ 48 ⌧
3/8" - 16 2-7/8 (73.0) 5/16" /18 1-1/2 (38.1) 1-3/8 (34.9) 50/ 3.8 500/ 40 ⌧ ⌧
(head dia. .722) 4 (101.6) 5/16" /18 1-1/2 (38.1) 2-1/2 (63.5) 50/ 5.3 400/ 4 ⌧ ⌧
5 (127.0) 5/16" /18 1-1/2 (38.1) 3-1/2 (88.9) 50/ 5.6 300/ 40 ⌧
6 (152.4) 5/16" /18 1-1/2 (38.1) 4-1/2 (114.3) 50/ 8.0 300/ 48 ⌧
Threshold 1/4" - 20 2-1/4 (57.2) 3/16" /24 1-1/8(28.6) 1-1/8 (28.6) 100/ 2.5 1000/ 25 ⌧
Flat Head (head dia. .385) ⌧
Round Head 1/4" - 20 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 1.9 1000/ 20 ⌧
2 (50.8) 3/16" /24 1-1/8 (28.6) 7/8 (22.2) 100/ 2.7 1000/ 28 ⌧ ⌧
2-7/8 (73.0) 3/16" /24 1-1/8 (28.6) 1-3/4 (44.5) 100/ 3.7 1000/ 38 ⌧
3/8" - 16 2-5/8 (66.7) 5/16" /18 1-1/2 (38.1) 1-1/8 (28.6) 50/ 3.9 500/ 41 ⌧
Tie Wire 5/16" - 18 1-1/2 (38.1) 1/4" /20 1-1/2 (38.1) 9/32 (7.1) 100/ 4.9 1000/ 50 ⌧
Hex Coupling 3/8" - 16 1-7/8 (47.6) 3/8" /16 1-1/2 (38.1) -- -- 50/ 6.0 250/ 30 ⌧
(Rod Hanger) Hanger ⌧
1/2" - 13 2-1/4 (57.2) 1/2" /13 1-7/8 (47.6) -- -- 25/ 6.5 125/ 34 ⌧
Hanger
Zinc Plating
304 Stainless Steel
(800) 486-1832 www.trianglefastener.com
136

DYNABOLT ® SLEEVE ANCHORS
DYNABOLT ® SLEEVE ANCHORS
VERSATILE HEAVY-DUTY SLEEVE ANCHORS
Technical Data
Tension and Shear
DYNABOLT SLEEVE ANCHORS PERFORMANCE TABLE
ULTIMATE TENSION AND SHEAR VALUES IN CONCRETE* AND (LBS/KN)
Anchor Installation Bolt Embedment f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa)
Dia. Torque Dia. Depth Anchor Tension Shear Tension Shear Tension Shear
In. (mm)Ft. Lbs. (Nm) In. (mm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)
1/4 (6.4) 3.5 (4.7) No. 10 1-1/8 (28.6) 1,200 (5.3) 1,620 (7.2) 1,600 (7.1) 1,620 (7.2) 2,100 (8.5) 1,620 (7.2)
5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,400 (6.2) 2,040 (9.1) 1,920 (8.5) 2,220 (9.9) 2,600 (11.6) 2,400 (10.7)
Carbon
3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,560 (11.4) 2,240 (10.0) 2,800 (12.5) 3,100 (13.8) 3,040 (13.5)
or
1/2 (12.7) 20 (27.1) 3/8 (9.5) 1-7/8 (47.6) 2,220 (9.9) 4,000 (17.8) 3,140 (14.0) 4,500 (20.0) 4,400 (19.6) 5,000 (22.2)
Stainless
5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,080 (13.7) 6,440 (28.6) 4,400 (19.6) 7,240 (32.2) 6,120 (27.2) 8,080 (35.9)
3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 4,200 (18.7) 10,200 (45.4) 5,940 (26.4) 11,600 (51.6) 8,900 (39.6) 13,100 (58.3)
DYNABOLT SLEEVE ANCHORS PERFORMANCE TABLE
ULTIMATE TENSION AND SHEAR VALUES IN LIGHTWEIGHT CONCRETE (LBS/KN)*
Anchor Installation Bolt Minimum f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa)
Dia. Torque Dia. Embedment Anchor Tension Shear Tension Shear
In. (mm) Ft. Lbs. (Nm) In. (mm) Depth In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)
1/4 (6.4) 3.5 (4.7) No. 10 1-1/8 (28.6) 1,080 (4.8) 1,620 (7.2) 1,220 (5.2) 1,940 (8.6)
5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,260 (5.6) 1,680 (7.5) 1,440 (6.4) 2,220 (9.9)