Hand Controls - Custom Chrome

Hand 

Controls 

Proudly Distributed by

10” 10” 

12” 

12” 

16” 

16” 

Santee 1” Ape Hanger Handlebars 

1” steel handlebars, works with either early or late model style controls 

(except throttle-by-wire models). Available in 10”, 12”, and 16” 

heights and in either a chrome-plated or Satin black powder coated 

finish. Not knurled. 

Pre-82 models 

10” rise, 32.5” width, 7” pullback, 8” center 

110000 10” Ape Hanger, Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$34.99 

602222 10” Ape Hanger, Satin Black . . . . . . . . . . . . . . . . . . . . . . . . . . .$31.99 




16” rise, 35” width, 7” pullback, 8” center 



1982-up models (with wiring recess) 










Santee 1” Ape Hanger Handlebars Pre-Drilled for 

Internal Wiring 

1” steel handlebars are knurled and pre-drilled for internal wiring for 

a custom look and works with either early or late models style controls 

(except throttle-by-wire models). Available in 10”, 12”, and 16” 

heights and in either a chrome-plated or satin black powder coated 

finish. 










2 

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Available in black 

110023 

693688 

55484 

693689 

55401 

110019 

Santee 1” Wide and Low Handlebars 

1” steel handlebars, works with either early or late model style 

controls (except throttle-by-wire models). Available in different 

widths to optimize comfort and in either a chrome-plated or black 

powder coated finish. 

Pre-82 models 

110019 24” wide Drag bar, Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . .$23.99 

602213 24” wide Drag bar, Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$19.99 





55400 39” wide Drag bars, Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . .$34.99 

110023* XLX style, Chrome (5” rise, 32” wide, 7” pullback, 6” center) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$28.99 

602219* XLX style, Black (5” rise, 32” wide, 7” pullback, 6” center)$26.99 

82-12 models (except 08-12 Touring) 







55401 39"-wide with slight rise and 2" pullback, Chrome . . . . . . .$36.99 

110033* XLX style, Chrome (5” rise, 32” wide, 7” pullback, 6” center) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$33.99 

602218* XLX style, Black (5” rise, 32” wide, 7” pullback, 6” center) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $29.99 

1 1/4” T-Bars 

These bars are designed to fit most models from 82-12 including 

Throttle-By-Wire applications with 3.50” center to center riser 

mounting holes. For internal wiring only. 

Chrome T-Bars 

693686 6” T-Bar (width 30”, height 6”, pullback 11”) . . . . . . . . $129.99 


693690 10” T-Bar (width 30”, height 10”, pullback 11”). . . . . . $144.99 

Black Powder Coated T-Bars 



693691 10” T-Bar (width 30”, height 10”, pullback 11”). . . . . . $134.99 

693650 

693653 

‘Straight-Up’ 1 1/4” T-Bars 

These are the perfect bars to give your ride that aggressive, no 

non-sense look. They feature straight risers, pre-drilled for internal 

wiring (with a pre-installed pull wire) and will fit all models from 

82-12 including ‘Throttle by Wire’ applications. Available in a 

chrome-plated or gloss black finish.77cm 

Chrome 

693650 8” ‘Straight-Up’ T-Bars, Chrome . . . . . . . . . . . . . . . . . . . . $144.99 

693652 10” ‘Straight-Up’ T-Bars, Chrome . . . . . . . . . . . . . . . . . . . $149.99 

693654 12” ‘Straight-Up’ T-Bars, Chrome . . . . . . . . . . . . . . . . . . . $159.99 

Black 

693651 8” ‘Straight-Up’ T-Bars, Black. . . . . . . . . . . . . . . . . . . . . . . $144.99 

693653 10” ‘Straight-Up’ T-Bars, Black. . . . . . . . . . . . . . . . . . . . . . $149.99 

693655 12” ‘Straight-Up’ T-Bars, Black. . . . . . . . . . . . . . . . . . . . . . $159.99 

www.customchrome.com 3

37139 

31776 

37140 

16" 

641263 

37141 

631015 

641264 

14" 

641261 

641262 

Khrome Werks Knurled Handlebars for Springer 

Models 

1"-diameter, 14-gauge steel tubing. Chrome-plated and diamond 

knurled for OEM Springer Softail models to fit on stock risers with 4 

3/4" centers. Dimpled for late model controls. Made in USA. 

37139 12" Ape Hanger for FXSTS models from 88-12 . . . . . . . . . . .$64.99 

631015 16" Ape Hangers for FXSTS, and FLSTS models from 88-12 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$67.99 

37140 Glide-style for FXSTS models from 88-12 . . . . . . . . . . . . . . . .$59.99 

31776 Stock replacement for FXSTS models from 88-12 and FXSTSB 

models from 95-97 (repl. OEM 56093-88). . . . . . . . . . . . . . . .$59.99 

31021 Stock replacement for FLSTS Heritage Springer Softail models 

from 97-12 (repl. OEM 55933-97) . . . . . . . . . . . . . . . . . . . . . . .$59.99 

Chrome Bad Boy Style Handlebar 

Get the look of a Bad Boy model on bikes with standard 3 1/2" riser 

spacing. 

37141 For 82-12 models with risers on 3 1/2" centers . . . . . . . . . . .$59.99 

12" 

641279 

Burly Narrow Glide Ape Hangers 

These tapered bottom 1” bars look just right when installed on 

models with Narrow Glide front ends like Sportster and most Dyna’s. 

Slotted and drilled for easy internal wiring. Installation will require 

longer cables and extension of handlebar wiring. Fits all models from 

82-12 (except models with Throttle-by-Wire) 


641279 12" Narrow Ape Hangers, Chrome . . . . . . . . . . . . . . . . . . . .$144.99 

641262 14” Narrow Ape Hangers, Chrome . . . . . . . . . . . . . . . . . . . .$144.99 

641264 16” Narrow Ape Hangers, Chrome . . . . . . . . . . . . . . . . . . . .$144.99 

Black 

641278 12" Narrow Ape Hangers, Black . . . . . . . . . . . . . . . . . . . . . . .$129.99 

641261 14” Narrow Ape Hangers, Black . . . . . . . . . . . . . . . . . . . . . . .$129.99 

641263 16” Narrow Ape Hangers, Black . . . . . . . . . . . . . . . . . . . . . . .$129.99 

Khrome Werks Narrow Glide Ape Hangers 

Chrome 12" high ape hangers are designed with narrow glide bikes 

in mind. 61/2" center width for cruising comfort. 

31020 For Narrow Glide models from 82-12 (except 08-12 Touring 

models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$62.99 

4 


Khrome Werks Handlebars 

Put your hands where you want them with a set of Khrome Werks 

top quality made in America handlebars. Each bar is carefully 

formed, polished and chrome-plated with a diamond knurled 

center for positive, non-slip clamp in the risers. 

Late-Model Replica Bars 

Patterned after popular stock bars with wiring dimples for latemodel 

controls. Knurled on 3 1/2" centers (except FXSTS bars). 

37155 For FLST Classic models from 87-12 (repl. OEM 56569-86) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$59.99 

37156 For FX Softail Springer from late 87-12 (repl. OEM 56093-88) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$59.99 

31021 Stock replacement for FLSTS Heritage Springer Softail models 

from 97-12 (repl. OEM 55933-97) . . . . . . . . . . . . . . . . . . . . .$59.99 

Buckhorn Bars 

Among the most comfortable bars for any bike. 

37147 Late-model style with wiring dimples (repl. OEM 56081-82) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$59.99 

Ape Hangers 

Knurled on 3 1/2" centers. Bars for models from 82-10 have dimples 

for late model external wiring. 

37156 

37118 

37155 

82-12 Price Pre-82 Price 

12"-rise 37150 $64.99 37148 $59.99 

16"-rise 37151 $69.99 37149 $64.99 

18”-rise 631013 $78.99 631014 $76.99 

37159 

Early Glide-Style Bars 

Accurate reproduction of the bar used until 57. Knurled on 3 1/2" 

centers. 

37159 Early-style without dimples or drilled . . . . . . . . . . . . . . . . .$57.99 

Favorite Custom Bends 

Here’s some of the favorite custom bars ever bent for Harley- 

Davidson motorcycles. Knurled at 3 1/2" centers. 

31750 Low-rise drag bar with dimples . . . . . . . . . . . . . . . . . . . . . . .$57.99 

37124 Drag bar with dimples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$53.99 

37123 Drag bar for early internal wiring not knurled, drilled or 

dimpled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$44.99 

37118 High-rise buckhorn pullback . . . . . . . . . . . . . . . . . . . . . . . . .$62.99 

31026 FLST-style for Road King models from 97-12 . . . . . . . . . . .$62.99 

37149 

37123 

631013 

31026 

31750 

31021 


Jammer Riser Style Hollywood Handlebars 

We’ve adapted our “Hollywood” bars for use with risers on front ends with 3 1/2” centers. Made of 1" tubing, un-dimpled for use with pre-82 

controls and measuring 34" from tip to tip, these handlebars have a 6" rise and feature a cable exit hole for those using our internal clutch and 

throttle assemblies shown elsewhere. These bars will give your ride an instant “old school” look! Made for Jammer by Paughco in USA. 

632367 Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $219.99 

632368 Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $219.99 

632366 

632369 

Jammer Hollywood and Speedster Handlebars for Springers 

Those of you familiar with old iron will remember these handlebars used on 36-57 models. Originally designed to use piano wire style internal 

throttle and spark advance cables, we’ve updated them for use with pre-82 controls and fitment to our Jammer or other aftermarket “inline” 

Springer front ends. Simply remove the top tree and install the bars in its place... instant Cool! Both styles are made of 1" tubing, are undimpled, 

measure 36" from tip to tip, have a 6" rise and feature cable exit holes for those using our internal clutch and throttle assemblies shown 

elsewhere. The “Hollywood” handlebars feature the crossbar while the “Speedster” handlebars do not. Both styles are truly retro inspired, and 

available either black powder coated or chrome-plated. The “Hollywood” style bars are featured on our “Delta 88” build. Made exclusively for 

Jammer right here in USA by Paughco. 

632365 “Hollywood” bars for Springer-Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $364.99 

632366 “Hollywood” bars for Springer-Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $364.99 

632369 “Speedster” bars for Springers-Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $319.99 

632370 “Speedster” bars for Springers-Black. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $319.99 

6 




Jammer "Z" Bars-6" Narrow Style 

These 60's Chopper style "Z" bars are 1 inch in diameter, have 6 

inches of rise with a 7 inch center width. Bars measure 12 1/2 inches 

in length, with a pullback of 8 inches. Centerline width (tip to tip) 

measures 24 1/2 inches. Angle of pullback is about 45 degrees. 

632331 Chrome, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$54.99 

651810 Black, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$54.99 


Jammer "Z" Bars-10" Wide Style 

These "Z" bars are 1 inch in diameter, have 10 inches of rise with a 

7 1/4 inch center width. Bars measure 11 1/2 inches in length, with 

a pullback of 4 1/2 inches. Centerline width (tip to tip) measures 28 

1/2 inches. Angle of pullback is about 25 degrees. 

632336 Without indent, Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . $55.99 

632335 With Indent, Chrome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $55.99 

651819 Without indent, black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $55.99 

651820 With Indent, black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $55.99 


These "Z" bars are 1 inch in diameter, have 8 inches of rise with a 7 

1/4 inch center width. Bars measure 11 1/2 inches in length, with a 

pullback of 4 1/2 inches. Centerline width (tip to tip) measures 28 1/2 

inches. Angle of pullback is about 25 degrees. 

632333 Chrome, non-dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$54.99 

651817 Black, non-dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$52.99 

632332 Chrome, dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$54.99 

651818 Black, dimpled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$52.99 



These "Z" Bars are 1 inch in diameter, have 8 inches of rise with a 


a pullback of 8 inches. Centerline width (tip to tip) measures 24 1/2 


632334 Chrome, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$54.99 

651812 Black, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$55.99 




These "Z" bars are 1 inch in diameter, have 4 inches of rise with a 


a pullback of 8 inches. Centerline width (tip to tip) measures 24 1/2 


632328 Chrome, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $54.99 

651811 Black, Dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $51.99 



These 60's Chopper style "Z" Bars are 1 inch in diameter, have 4" of 

rise with a 7 1/4" center width. Bars measure 11 1/2" in length, with 

a pullback of 4 1/2 inches. Centerline width (tip to tip) measures 28 

1/2". Angle of pullback is about 25 degrees. 

632326 With indent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$49.99 

632327 Without indent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$49.99 

651815 With indent, black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$48.99 

651814 Without indent, black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$47.99 


These 60's Chopper style "Z" bars are 1 inch in diameter, have 6 

inches of rise with a 7 1/4 inch center width. Bars measure 11 1/2 

inches in length, with a pullback of 4 1/2 inches. Centerline width 

(tip to tip) measures 28 1/2 inches. Angle of pullback is about 25 

degrees 

632330 Chrome, non-dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $49.99 

651813 Black, non-dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $49.99 

632329 Chrome, dimpled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $54.99 

651816 Black, dimpled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $49.99 


Keystone 

Chumps 

Tracker 

Clubman 

12" Apes 

Frisco 

8 


Windows 

Low-Drags 

Custom 1” Handlebars by Biltwell Inc. 

Biltwell handlebars are precision crafted with 100% seamless 4130 

chromoly. The wall thickness of our tubing is a burly .120“. Most bars 

are available smooth for custom applications, or with dimples to 

accomodate original equipment throttle, brake and clutch assemblies. 

(Clubmans are not dimpled so you can flip them either way, chopper 

or cafe style). 

Tracker 

Racy and simple design is comfortable and built for performance. 30” 

wide, 5.25” center width, 1.75” rise, 2” pull back 

633228 Tracker bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . . . . $79.99 

633229 Tracker bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . . . $79.99 

633230 Tracker bars, dimpled, black . . . . . . . . . . . . . . . . . . . . . . . . . . $79.99 

633231 Tracker bars, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . . . . $79.99 

Clubman 

Can’t find 1-inch Clubman bars for your café-inspired H-D-based custom? 

Look no further. 29” wide, 6.75” center width, 0.5” rise, 6” pull 

back 

633206 Clubman bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . . $99.99 

633207 Clubman bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . . $99.99 

Low Drag 

Riser-less bar with 1/2x13 threaded insert welded into the bases of 

each bar makes for a sturdy, compact and strong design. Bolt these 

up and trim the ends just as narrow as you can stand for a nice lanesplitting 

profile. 26.5” wide, 3.5” center width, 3.5” rise, 3” pull back 

633224 Low Drag bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . $99.99 

633225 Low Drag bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . $99.99 

633226 Low Drag bars, dimpled, black . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633227 Low Drag bars, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . . $99.99 

Keystone 

Looking for still more style and originality for your custom bike? 

Consider the Keystone bar. Similar to the Z Bar in every detail, but 

the uprights are angled inward for a more aggressive look. 28” wide, 

6.5” center width, 2” rise, 2” pull back 

633202 Keystone bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . . $99.99 

633203 Keystone bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . . $99.99 

633204 Keystone bars dimpled, black . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633205 Keystone bars, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . . $99.99 

Frisco 

Chopper freaks in the 1960’s cooked up some pretty wild handlebars 

for their custom death traps, especially in California’s fabled San 

Francisco Bay Area. Our Frisco bar pays homage to the bikes of guys 

like Sonny Barger, Arlen Ness and Tobie Gene Levingston. 29” wide, 

5.75” center width, 7” rise, 1” pull back 

633208 Frisco bars, non-dimpled, black. . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633209 Frisco bars, non-dimpled, chrome. . . . . . . . . . . . . . . . . . . . . . $99.99 

633210 Frisco bars dimpled, black. . . . . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633211 Frisco bars, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

8“ Chumps 

Nice low rise bar that works with just about any bike. Want 

something modern and comfortable but not wacky styling? Maybe 

Chumps are just the ticket. 29.5” wide, 5.25” center width, 8” rise, 

6.5” pull back 

633216 Chumps bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . . . $99.99 

633217 Chumps bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . . . $99.99 

633218 Chumps bars dimpled, black . . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633219 Chumps bars, dimpled, chrome. . . . . . . . . . . . . . . . . . . . . . . . $99.99 

12“ Apes 

Traditional Apehangers without the ridiculous dimensions of today‘s 

contemporary tall bars. These are about as narrow as you can go at 

the base and still mount up to a stock HD clamp. 30.5” wide, 5.25” 

center width, 12” rise, 9” pull back 

633212 12” Apehanger, non-dimpled, black . . . . . . . . . . . . . . . . . . . $99.99 

633213 12” Apehanger, non-dimpled, chrome . . . . . . . . . . . . . . . . . $99.99 

633214 12” Apehanger, dimpled, black . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633215 12” Apehanger, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . $99.99 

Windows 

Built for speed in the attack position these bars are strong and 

narrow. Trim the ends off as much as possible and start dodging 

mirrors. 27.5” wide, 5.25” center width, 9” rise, 1.5” pull back 

633220 Window bars, non-dimpled, black . . . . . . . . . . . . . . . . . . . . . $99.99 

633221 Window bars, non-dimpled, chrome . . . . . . . . . . . . . . . . . . . $99.99 

633222 Window bars dimpled, black . . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

633223 Window bars, dimpled, chrome . . . . . . . . . . . . . . . . . . . . . . . $99.99 


633181 

633185 

633177 

633182 

633186 

633178 

633188 

Biltwell Handlebars 

Biltwell handlebars are precision crafted with 

100% seamless 4130 chromoly. The wall thickness 

of our tubing is a burly .120”. Most handlebars 

are available smooth for custom applications, 

or with dimples to accommodate H-D original 

equipment throttle, brake and clutch assemblies. 

• Precision mitered & TIG welded joints 

• Seamless 4130 chromoly 

• Two finishes: brilliant chrome plate, matte 

black electroplate 

Breezer Bar (W: 26”/H: 8”/PB: 4,75”) 

633176 Black (Non-Dimpled) . . . . . . . . . . . . . . $99.99 

633177 Chrome (Non-Dimpled). . . . . . . . . . . . $99.99 

633178 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 

633179 Chrome (Dimpled) . . . . . . . . . . . . . . . . $99.99 

H-Bar (W: 22,5”/H: 8”/PB: 2”) 



633182 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 


High Drags (W: 25,5”/H: 7”/PB: 3”) 



633186 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 


Moto Bar (W: 30,25”/H: 4,25”/PB: 2,75”) 



633190 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 


Mustache bar (W: 26”/H: 3”/PB: 5”) 



633194 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 


Zed Bar (W: 23,5”/H: 5”/PB: 3,5”) 



633198 Black (Dimpled). . . . . . . . . . . . . . . . . . . $99.99 


633191 

633194 

633193 

633199 

633198 

10 


641618 

633169 

641619 

Dog Bone Handlebar Top Clamp by Biltwell 

This cast stainless steel dog bone clamp is a great addition to the 

Biltwell Slimline risers. They are perfect for use with taller bars or if 

you just want that extra clamping surface and rigidity with a ‘lowkey’ 

clean look. They are available in a polished or black finish and 

were designed to only be used with Biltwell ‘Slimline’ Risers. 

641618 Polished Dog Bone top clamp . . . . . . . . . . . . . . . . . . . . . . . . . .$59.99 

641619 Black Dog Bone top clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$59.99 

Biltwell Thunder Risers 

633169 Thunder Risers 1,75” Rise, 3,5” Spread Polished. . . . . . $139.99 

633170 Thunder Risers 1,75” Rise, 3,5” Spread Black. . . . . . . . . $139.99 

633265 

633266 

685463 

685462 

Slimline Risers by Biltwell 

Cast and polished 1 inch tall stainless steel risers with stainless steel 

hardware for 1 inch bars. 

685462 Polished stainless shorty risers . . . . . . . . . . . . . . . . . . . . . . . . . .$94.99 

685463 Black stainless shorty risers. . . . . . . . . . . . . . . . . . . . . . . . . . . . .$94.99 

Trio Risers by Biltwell 

The Trio riser assembly has everything you need to clean up the top 

tree on 39mm and 41mm Harley hydraulic forks. Set includes two 

Slimline lower clamps, one Dogbone top clamp and four 5/16-18 

allen cap screws. Fits stock top clamps with a 3.5” riser bolt spread. 

633265 Trio risers polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $119.99 

633266 Trio risers black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $119.99 


84689 

651821 

’Shorty’ Risers 

Custom risers approx. 1” tall avaialble in either a chrome-plated or 

gloss black finish. 

84689 Chrome, pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $59.99 

651821 Black, pair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $50.99 

Heavy-Duty Polyurethane 

Handlebar Damper Kit 

If it's time to upgrade your 

handlebars, don't forget to replace 

the rubber dampers. Polyurethane 

bushings provide excellent vibration 

damping while providing superior 

deflection resistance for much 

improved steering feel. Includes thick 

chrome washers and steel sleeves Fits 

most models from 73-12. 

42901 Black (repl. OEM 56157-85T) . . . . . . . . . . . . . . . . . . . . . . . . . . .$10.99 

Jammer Offset Dog Bone Risers 

These Offset Dog Bone Risers are what you need to go with your 

retro ride, and are available in 3", 4" & 6" lengths. Machined of 

solid steel and chromed, and include rubber grommets in riser top to 

dampen vibration. Risers have 1/2" X 13 threads. Sold in pairs. 

632323 Offset Dog Bones - 3 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$169.99 



Polyurethane Damper Bushings 

These handlebar riser bushings by Ride-One are 28% stiffer than stock 

style rubber bushings. The polyurethane material provides a firm feel 

and holds up well under ozone exposure and vibration dampening to 

help assure a safe, comfortable ride. Fits all models from 73-12 (except 

‘Touring’ models). 

110088 Pack of 4 bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $7.99 

632224 

Hex-Head Riser Bolts 

Zinc-plated hex head steel riser bolts for most aftermarket and OE 

triple trees. Sold in pairs. 

84687 1/2" x 3 1/2" UNF for steel risers . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 

84688 1/2" x 3 1/2" UNC for aluminum risers. . . . . . . . . . . . . . . . . . . .$7.99 

632230 

632225 

632228 

651225 

632229 

632231 

Jammer Straight Dog Bone Style Risers 

Straight dog bone risers available in 3" & 5" rise for use when 

mounting 1" bars to Springer's using our #632222 inline triple clamp. 

Made in USA by Paughco. 

632224 Dog Bone style risers for 1" bars. 3" rise . . . . . . . . . . . . . . .$139.99 

632225 Dog Bone style risers for 1" bars. 5" rise . . . . . . . . . . . . . . .$145.99 

651225 Dog bone style risers for 1" bars. 7" rise . . . . . . . . . . . . . . .$149.99 

Jammer Riser Studs and Bolts 

A selection of studs and bolts in varying lengths for use in mounting 

risers with 1/2"-20 thread size. 

632228 1/2"-20 x 1 1/2" riser bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7.99 

632229 1/2"-20 x 1 1/2" riser studs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 

632230 1/2"-20 x 2" riser bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7.99 

632231 1/2"-20 x 4" sockethead riser bolts. . . . . . . . . . . . . . . . . . . . . .$18.99 

12 


632222 

Custom Riser Set for Springer 

Softail Models 

Specifically designed to isolate the 

handlebars in rubber and minimize 

vibration, while raising them approximately 

2"-above the stock position and 2"-closer 

to the rider. Includes mounting hardware. 

It may be necessary to install longer-thanstock 

brake lines and control cables if 

retaining the Original Equipment buckhorn 

handlebars. 

08974 Fits FXSTS models from late 88-11 

. . . . . . . . . . . . . . . . . . . . . . . . . . .$169.99 

Jammer Handlebar Damper 

Bushing Kit 

Helps eliminate flexing when using heavy 

or high handlebars. This kit features 

transparent Polyurethane damper bushings 

& one-piece Chrome caps & inserts that 

work/look better than the old style bushing 

kits. For use in Custom applications and most 

models 73-12, except FLT/FLH & Springer 

models. 

632940 Jammer Handlebar Damper 

Bushing Kit . . . . . . . . . . . . . . . $34.99 

632223 

Jammer Dog Bone Inline Triple 

Clamp 

Just what you need to use with our Dog 

Bone risers to mount 1” handlebars to our 

springers that use an “inline” triple clamp. 

A very retro, very cool look! A stud kit is 

also available to thread into the unused 

riser stud holes on springers when using 

dog bone risers. A trick little idea that really 

cleans things up! Made in USA by Paughco. 

632222 Dog Bone inline triple clamp 

(with ears) . . . . . . . . . . . . . $156.99 

632223 Kit for riser stud holes when using 

dog bone risers . . . . . . . . . . . . . .$29.99 

632233 

632232 

T-Bar Clamp by Paughco 

This clamp is for use in mounting T-bar 

handlebars with built in risers to springers. 

A cool idea from Ron & gang at Paughco! 

A mounting hardware kit is also available. 

Made in USA. 

632232 T-bar clamp. . . . . . . . . . . . . . . . .$219.99 

632233 Mounting hardware kit for CC 

#632232. . . . . . . . . . . . . . . . . . . . .$49.99 

Solid-Mount Handlebar Kits 

Kits eliminate rubber-mounted handlebars 

and fit aluminum or steel fork crowns. Easy 

to install and highly recommended when 

installing high bars and/or risers. 

14921 Fits all Big Twin and Sportster 

models from 73-12 with rubber 

handlebar bushings . . . . . . . . . . .$9.99 

14922 Fits all Big Twin and Sportster 

models thru 72 with steel press-fit 

bushings (shown) . . . . . . . . . . . . .$9.99 

Chrome Handlebar Damper Kit 

Kit includes chrome-plated cup washers 

(made from 16 gauge heat-treated steel) 

rubber bushings and spacers. Fits models 

with threaded risers from 73-12. 

26152 Replaces OEM 56157-85T . . . . . .$7.99 

32769 

Riser Bolts 

A better looking alternative to the Original 

Equipment bolts. Fit all models with threaded 

risers from 73-12. 

32771 Chromed 12-point bolts (sold in 

pairs) . . . . . . . . . . . . . . . . . . . . . . .$18.99 

32769 Chromed torx bolts (sold in pairs) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$19.49 

Chrome Handlebar Damper Kit 

Perfect for repairing worn-out bushings or 

when installing new front ends. Includes 

four rubber bushings with chrome cup 

washers and two 1/2"-13 studs with chrome 

nylon-inserted lock nuts. 

10043 Fits all models with threaded risers 

from 73-12 (except 5-speed ‘Touring’ 

models) . . . . . . . . . . . . . . . . . . . . .$18.99 


27299 

632947 

27296 

632946 

Retro Handlebar Control Cones by 

Paughco 

Here’s some cool little goodies that’ll give your ride a 

decidedly retro look! Reminiscent of the old internal wire 

set up used on older H/D’s, they slip onto the handlebar 

and butt up to your grips for a clean, finished look. For 

use with 1” handlebars with internal throttle & clutch 

set-ups where no switch housings are used. Available in 

either Chrome plated steel or Brass, and your choice of 

Tapered or Radiused styles. Affix with silicone adhesive. 

These look great installed! Sold in Pairs. Made in Nevada, 

USA by the crew at Paughco. 

632945 H/Bar Control Cones. Tapered Chrome . . . . . $49.99 

632946 H/Bar Control Cones. Radiused Chrome . . . . $49.99 

Handlebar Wiring Harnesses with Switches 

Two styles are available. Chrome switches with black lettering or reproductions of 

the black Original Equipment switches, both with properly color-coded wires presoldered 

to them. 

Complete Harnesses with Switches 

Each switch set comes complete with a 48"-long wiring harness (8"-longer than 

stock) which will accommodate the tallest handlebars. They also include all 

terminals, pin connectors and mounting hardware, and are ready-to-install in your 

switch housings. Fit all Sportster and Big Twin models from 82-95 (except 94-95 XL 

and FLHR; and those with radio controls). 

Black Price Chrome Price 

Complete kit 27299 $78.99 27296 $99.99 

Right side kit ONLY 27298 $42.99 27295 $51.99 

Left side kit ONLY 27297 $39.99 27294 $51.99 

Replacement Switches Only 

Perfectly suited as replacements for the Original Equipment parts. They come with 

12"-lengths of properly color-coded wire soldered to them and fit all Sportster 

and Big Twin models from 82-95. 

Black Price Chrome Price 

Dimmer/horn (repl. OEM 71597-92) 27280 $14.99 27285 $18.99 

Left turn signal (repl. OEM 71598-92) 27281 $9.99 27286 $9.99 

Engine stop/start (repl. OEM 71589-92) 27282 $14.99 27287 $17.99 

Right turn signal (repl. OEM 71591-92) 27283 $9.99 27288 $9.99 

Front stoplight switch (repl. OEM 71590-92) 27284 $7.99 

Master Cylinder Assemblies for Models 

from 82-95 

These complete master cylinder assemblies include 

brake lever, master cylinder cover and all other internal 

components. Available in chrome for single discmodels 

as well as most custom applications using 1"-diameter 

handlebars. Clamp and screw sets sold separately. 

110466 Fits single disc models from 82-95. Chrome, 5/8"- 

bore. Replaces OEM 45019-85 . . . . . . . . . . . . $159.99 

Replacement Parts 

110528 Master cylinder rebuild kit for 5/8” bore. Fits FX 

models 84-86, FXR models 84-99 (except FXRT, 

FXRS-SP and FXRS-CON) and Softail models 84-95. 

(repl. OEMs 45069-84, 45072-87, 345072-87) . $9.99 

14 


Chrome Handlebar Control Kits 

Available with or without chrome switches and complete 

handlebar wiring harnesses. They fit all models from 

82-95. Switch housings have a smooth look with no 

casting groove, and the master cylinder assembly is 

complete with the handlebar clamp, chrome mounting 

hardware and a banjo bolt. The clutch lever assembly 

includes both styles of cable pin permitting the use of 

the early-style cable, as well as the latest eyelet type. 

The switches and wiring harnesses duplicate OEM color 

coding with 48"-leads (8"-longer than stock), and include 

all necessary terminals, pin connectors and mounting 

hardware. If you plan to use your existing wiring and 

switches, the kits are also available without electrical 

components. 

Kits with Chrome Switches and Wiring 

26393 With 3/4"-bore (.750") master cylinder for dual 

disc models from 82-83 . . . . . . . . . . . . . . . . . . $299.99 

26394 With 5/8"-bore (.625") master cylinder for single 


Kits without Switches or Wiring 

26273 With 3/4"-bore (.750") master cylinder for dual 


26295 With 5/8"-bore (.625") master cylinder for single 


Brake Master Cylinders 

Include lever, clamp and hardware. 

26281 Complete 3/4"-bore master cylinder (repl. OEM 

45013-82) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $129.99 

26286 Complete 5/8"-bore master cylinder (repl. OEM 

45019-85) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $129.99 

26364 Complete 9/16"-bore master cylinder . . . . . $129.99 

Individual Components 

26276 Clutch lever assembly. . . . . . . . . . . . . . . . . . . . . $38.99 

26287 Clutch lever assembly with ergonomic lever blade 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $44.99 

26278 Switch housing, right top (repl. OEM 71564-82) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $10.99 

26280 Switch housing, right bottom (repl. OEM 71563- 

82A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $12.99 

26277 Switch housing, left top (repl. OEM 71567-82) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $10.99 

26279 Switch housing, left bottom (repl. OEM 71568- 

82A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $11.99 

26288 Cover, replaces OEMs 45004-85, 42381-87 . . $11.99 

26282 Rebuild kit for 3/4"-bore master cylinders . . $23.99 

26306 Rebuild kit for 5/8"-bore master cylinders . . $19.99 

26275 Lever clamp only for clutch/brake (repl. OEM 

45044-82) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $11.99 

12741 Chrome brake lever (repl. OEM 45064-82T). . $9.99 

12743 Chrome clutch lever (repl. OEM 45062-82T). $10.49 

12799 82-95 brake and clutch set (repl. OEM 45049-92) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $28.99 

26283 Nylon pin for eyelet-style cables (repl. OEM 

45036-88) sold each . . . . . . . . . . . . . . . . . . . . . . . $3.99 

15951 Steel pin and nylon bushings for non-eyelet 

cables (card of 12), Replaces OEMs 45039-68, 

45036-68 (card of 12). . . . . . . . . . . . . . . . . . . . . $10.99 

28068 

26290 

28514 

Early-Style Chrome Handlebar Control Kits 

Our best-selling chrome-plated control kits are now available with chrome or 

black switches and complete handlebar wiring harnesses. They fit all models 

from 72-81 and are perfect for converting the black or silver-painted Original 

Equipment parts to show-quality chrome controls, or for those of you building 

bikes from the ground up. Each kit includes a master cylinder and clutch lever 

assembly, two switch housings, the complete handlebar wiring harnesses with 

chrome or black switches and button caps attached, and all of the hardware 

necessary for installation. A chrome kit without the switches and wiring is also 

available for those willing to re-use their Original Equipment harnesses. 

Complete Kits 

28514 With chrome switches and button caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . $144.99 

26290 With black switches and button caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $129.99 

26291 Complete kit without switches or wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . $99.99 

Individual Components 

28068 Complete master cylinder assembly (repl. OEM 45010-73). . . . . . . . . . . . . $87.99 

28112 Complete clutch lever assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $21.99 

28114 Chrome bracket only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $14.99 

26112 Vertical switch housing, chrome (repl. OEM 71539-73B) . . . . . . . . . . . . . . $14.99 

Replacement Parts 

26105 Chrome master cylinder body only (repl. OEM 45024-72) . . . . . . . . . . . . . $45.99 

26102 Rebuild kit for master cylinder, fits all models from 72-81 and CC #28068 

(repl. OEM 45063-72), 3/4". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

26060 Chrome brake lever (repl. OEM 45082-83T). . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

26059 Chrome clutch lever (repl. OEM 45080-83T). . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

15951 Steel pin and nylon bushings for non-eyelet cables (card of 12), Replaces 

OEMs 45039-68, 45036-68 (card of 12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $10.99 

26123 Set of the six replacement decals for vertical switch housings (pack of 10) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $6.99 


28508 

28510 

Early Chrome Handlebar Control Kits with Custom 

Switch Housings 

Popular chrome-plated control kits are available with or without a 

complete handlebar wiring harness with switches. Kits include master 

cylinder, clutch lever assembly, custom switch housings and mounting 

hardware. The kit with wiring harnesses has 48"-long color-coded wiring 

looms which have accurate reproductions of stock switches soldered in 

place. Replacement black or chrome wiring harnesses available separately. 

For all Big Twin and Sportster models 73-81. 

28508 With black switches and button caps . . . . . . . . . . . . . . . . . . . . . . .$129.99 

28509 Complete kit without switches or wiring . . . . . . . . . . . . . . . . . . . . .$99.99 

28510 Replacement switch housing (sold each). Fits all models from 72-81 

(replaces OEM 71539-73B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 

Note: Handlebars, risers and clamp not included. 

Wiring Harnesses with Switches 

With 48" leads, kits fit even the tallest handlebars. All mounting hardware 

and connectors included. 

Chrome Price Black Price 

Complete kit 27272 $62.99 26299 $38.99 

Left side only 27271 $31.99 26298 $19.99 

Right side only 27270 $31.99 26297 $19.99 

26113 

26123 

Mini Aluminum Handlebar 

Switch Boxes 

These sweet little switch boxes are only 1" 

tall, and radiused to mount neatly to your 

handlebars with a through screw that’s 

included. Made of aluminum, there are 2 

styles available; The “Double” switch box 

is 2” long X 1” tall and features 1 toggle 

switch for Hi-Low beam and 1 push-button 

switch for Start. The “Triple” switch box is 

2 1/2” long X 1” tall and features 1 toggle 

switch for Hi-Low beam, 1 push-button 

switch for Start and 1 push-button switch for 

horn. Great lookin’ switch boxes! Sold each. 

From the crew at Kijima in Japan. 

632785 “Double”. 1-toggle, 1-pushbutton 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$74.99 

632786 “Triple”. 1-toggle, 2-pushbuttons 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$79.99 

Custom Switch Housing 

Die-cast chrome-plated ‘pyramid’ housings 

use Original Equipment or Custom Chrome 

switches. Chrome sockethead hardware 

included. Sold each. 

28510 Replacement switch housing (sold 

each). Fits all models from 72-81 

(replaces OEM 71539-73B) . . . . .$9.99 

26112 26121 

Handlebar Switch Housings 

Chrome or polished reproductions of 

Original Equipment parts. There’s also a 

plain cover for custom set-ups. Housings use 

stock or CC switches and buttons. Include 

chrome sockethead screws and switch housing 

decals. For Sportster, FX and FL models 

from 72-81. 

Vertical Switch Housings 

26112 Vertical switch housing, chrome 

(repl. OEM 71539-73B) . . . . . . .$14.99 

Horizontal Switch Housings 

26121 Chrome . . . . . . . . . . . . . . . . . . . . . .$9.99 

Plain Switch Covers 

26113 Chrome . . . . . . . . . . . . . . . . . . . . . .$9.99 

26119 Polished. . . . . . . . . . . . . . . . . . . . . .$7.99 

Switch Housing Decals 

26123 Set of the six replacement decals for 

vertical switch housings (pack of 10) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .$6.99 

Extended Handlebar Wiring 

Harnesses without Switches 

48"-long wiring harnesses permit the 

installation of taller handlebars on most 

models from 73-95. They feature the 

correct gauge wires which are color-coded 

and then enclosed in black vinyl casings. 

The early kit includes 14 connectors 

and 3 terminals. The late kit includes 14 

connectors and 4 handlebar wiring retainer 

clips. 

15260 Fits all models from 73-81. . . . .$15.99 

26293 Fits most models from 82-95 . .$16.99 

16 


Note: Switch housings are shown 

for illustration purposes only. 

27272 

27275 

27276 

26092 

26089 

27277 

26093 

27273 

26090 

26299 

26106 

26091 

26123 

Early Handlebar Wiring Harness Kits 

Chrome or black switches and button capskits are 

completely soldered together and ready to install. They 

fit all Big Twin and Sportster models from 73-81, and are 

colorcoded to match the Original Equipment wires. 

Complete Harnesses with Switches 

48"-long kits fit the tallest handlebars. All the delicate 

soldering already done and all of the wire connectors, 

buttons, screws, stop light switch rubber boot and switch 

retaining plates are included. Complete kits or left and 

right sides only. 


Complete kit 27272 $62.99 26299 $38.99 

Left side only 27271 $31.99 26298 $19.99 

Right side only 27270 $31.99 26297 $19.99 

Replacement Switches 

Replacements for all models 72-81. Sold each unless noted. 


Run/off rocker switch (repl. OEM 71547-75) 27273 $9.99 26089 $8.99 

Hi/lo rocker switch (repl. OEM 71546-75) n/a 26090 $8.99 

Chrome replacement button cap only, pack of 

10 (repl. OEM 71535-72) 

27276 $14.99 26092 $9.99 

Short button cap (repl. OEM 71534-72) bag 

of 10 

27277 $14.99 26093 $9.99 

Plain rocker switch (no lettering) 27275 $7.99 n/a 

26091 Switch for starter, horn or turn signal (repl. OEM 71484-72). . . . . . . . . . . . . $5.99 

26106 Front stoplight switch (repl. OEM 72001-69A) . . . . . . . . . . . . . . . . . . . . . . . . . $5.99 

Switch Housing Label Kit 

Set of all six control decals, black on silver. 

26123 Set of the six replacement decals for vertical switch housings (pack of 10)$6.99 

26285 

26302 

26304 

26303 

26284 

Handlebar Switch Housing Components 

Fit 72-81 handlebar control switch housings. 

26284 Retaining plate for button switches (replaces OEM 71533-72) pack of 10. . . . . . . . . . $3.99 

26285 Rubber boot for the brake light switch (replaces OEM 27751-69P) pack of 10. . . . . . $5.99 

26302 Wire terminals–brake light switch (pack of 25). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $3.99 

26303 Screws–switch retaining plate #6-32 x 1/4" (replaces OEM 2803W) pack of 25 . . . . . $3.99 

26304 Screws–rocker switches #6-32 x 1/2" (replaces OEM 2804W) pack of 25. . . . . . . . . . . . $2.99 


12743 

12741 

Chrome Lever Blades for 82-92 

Replacement clutch and brake lever blades for all models from 82-92. 

Brake (82-92) 

12741 Chrome brake lever (repl. OEM 45064-82T). . . . . . . . . . . . . . .$9.99 

Clutch (82-87) 

Includes anti-rattle clip and screw 

12743 Chrome clutch lever (repl. OEM 45062-82T). . . . . . . . . . . . . .$10.49 

Note: Clutch levers fit models from 88-92 when used with OEM 45039-68 CC #15951). 

Early Lever Assemblies 

Fits FL Models from 65-67 

Fits all models requiring the small cable hole. 

26056 Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$13.99 

Fits Sportster Models from 65-70 

Fits all models requiring the large cable hole. 


Fits 72 Sportster Models ONLY 

Fits all models requiring the medium cable hole. 

12707 Polished (repl. OEM 38604-71) . . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 


26059 

26060 

26392 

Early Lever Blades 

Chrome-plated reproductions of the Original Equipment parts. 

26059 Chrome clutch lever (repl. OEM 45080-83T). . . . . . . . . . . . . . .$9.99 

26060 Chrome brake lever (repl. OEM 45082-83T). . . . . . . . . . . . . . .$9.99 

26391 

Clutch Levers and Perches 

Complete assembly includes lever, lever bracket, pivot pin and clip, 

cable anchor pin and plastic pin bushing set. Fits all models from 

73-81. 

28112 Complete clutch lever assembly . . . . . . . . . . . . . . . . . . . . . . . .$21.99 

28114 Chrome bracket only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$14.99 

Early Chrome Power Grip Lever Blades 

Strong, solid aluminum, chromed easy-pull power grip clutch and 

brake levers for all 65-81 models. Sold each. 

26391 Disc brake lever for all models from 72-81 (repl. OEM 45016- 

73T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$8.99 

26392 Clutch and drum brake lever for all models from 65-81 (repl. 

OEM 45017-69T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$8.99 

18 


604981 

Contoured ‘Slim-Line’ Rubber 

Grips 

These grips offer a classic ‘hourglass’ 

shape for the ultimate comfort. The black 

rubber surface offers plenty of grip, 

while the chrome end caps give them the 

finishing touch. 

604930 Contoured ‘Slim-Line’ Rubber Grips, 

fits all models from 73-12 (except 

08-12 touring models & models with 

air reservoirs in the handlebars) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$24.99 

604980 

604979 

Stroker Billet Grips 

CNC-Machined from billet aluminum with a knurled finish for a non-slip grip. Available in 

either a chrome-plated, black anodized or bronze finish. Fits all 73-12 single or dual cable 

applications (except 08-12 Touring models) 

604981 Chrome, Stroker Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$65.99 

604980 Black, Stroker Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$65.99 

604979 Bronze, Stroker Grips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$65.99 

Chrome and Rubber Cruiser 

Grips 

These grips offer a classic black rubber 

surface that offers plenty of comfort and 

grip, while the chrome end caps give them 

the finishing touch. 

604931 Chrome & Rubber Cruiser Grips, fits 

all models from 73-12 (except 08-12 

touring models & models with air 

reservoirs in the handlebars) . .$20.99 

604932 Chrome & Rubber Cruiser Grips, 

fits all models from 08-12 Touring 

models with electronic throttle by 

wire . . . . . . . . . . . . . . . . . . . . . . . .$22.99 

Leather Cushion Grips 

Black leather covered cushion grips with 

chrome end caps for all-day comfort. Fits all 

models from 73-12 (except 08-12 Touring 

and models with handlebar air reservoirs). 

78072 Sold in sets . . . . . . . . . . . . . . . . . .$20.99 

Vintage Chrome and Rubber Grips 

These grips offer a classic style that offers plenty of comfort and grip, while helping to reduce 

hand vibration. 

604934 Vintage Chrome & Rubber Grips, fits all models from 73-12 (except 08-12 touring models 

& models with air reservoirs in the handlebars) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$24.99 

604933 Vintage Chrome & Rubber Grips, fits all models from 08-12 Touring models with electronic 

throttle by wire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$24.99 


Throttle Pipe and Grip Sets 

Dual cable throttle pipes with Original Equipment-style replacement 

grips. Fits all models from 81-12 (except 08-12 Touring Models). Sold 

in sets. 

12791 Dual cable throttle pipe set . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 

Chrome Throttle Assemblies 

Throttle and grip sets for most models from 73-81. The throttle 

side assemblies have a chrome-plated throttle clamp assembly with 

adjustor and late grip with chrome end plug. The sets include a 

matched left hand side grip with chrome end plug. The chrome 

throttle clamps are also available separately. 

12914 Single cable assembly for all models from 73-80 (repl. OEM 

56500-79) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$15.99 

12915 Dual cable assembly for all 81 models and custom applications 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$15.99 

Chrome Handlebar Grip and Hole Plug 

Fits the hole in the handlebar grip on 60-early 83 models. 

15952 Replaces OEM 56238-62 (card of 12) . . . . . . . . . . . . . . . . . . . .$21.99 

OEM Style Rubber Grip Set 

Direct replacement for the OEM rubber grips. 

12164 OEM Style Rubber Grips, fits 81-12 Big Twin and Sportster models 

(except 08-12 Touring models and models with air reservoirs 

In the handlebars) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7.99 

604937 OEM Style Rubber Grips, fits 08-11 Touring models with throttle 

by wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$13.99 

12912 

651824 

Soft Touch Grip Set 

Soft neoprene foam absorbs vibration and stops finger ‘tingles’. 

Capped with chrome-plated ends. Fit all models from 73-12 (except 

08-12 Touring models and models with handlebar air reservoirs). 

12941 Sold in sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $14.99 

12901 Replacement foam covers (pair) . . . . . . . . . . . . . . . . . . . . . . . . . $3.99 

Universal Throttle and Grips 

Chrome throttle clamp with tension adjustor, includes both handle 

grips. 

12912 Chrome, Fits 1”-handlebars . . . . . . . . . . . . . . . . . . . . . . . . . . . $12.99 

651824 Black, Fits 1”-handlebars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $12.99 

Anderson-Style Heavy-Duty Grips 

12908 Set for 1"-bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $4.99 

12910 Left side for 1"-bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $2.99 

12911 1 1/8"-throttle side for 1"-bar . . . . . . . . . . . . . . . . . . . . . . . . . . $2.99 

20 


633271 

633241 

Biltwell Kung Fu Grips 

Motorcycle grips should be simple and comfortable. These BMXinspired 

units are exactly that. Thick ends are durable, small flanges 

are attractive and a million little rubber fins are comfy. Requires a 

throttle sleeve for installation (not included). 

633241 Kung-Fu grips black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$17.99 

633271 Kung-Fu grips natural . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$17.99 

633267 

633268 

Biltwell Whiskey Throttle Assembly 

The Biltwell Whiskey throttle is constructed of CNC-machined 6061 T-6 aluminum 

and fits all 1-inch O.D. handlebars. Two sets of four different cable 

ferrules are included with each full assembly. These plated steel ferrules fit 

both threaded and click-in barrel ends on stock Harley cables. If you don’t 

run stock H-D cables on your motorcycle, the ferrules provide plenty of 

options for custom single- or double-cable assembly. 

633238 Whiskey Throttle black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$99.99 

633239 Whiskey Throttle polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$99.99 

633267 Whiskey single throttle black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$99.99 

633268 Whiskey single throttle polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$99.99 

633240 Whiskey Throttle Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$49.99 


“Old School” Grips by Avon Grips 

These old, coke bottle style grips take ya right back to the good ‘ol days, 

but with a whole new twist! Manufactured right here in our grand state 

of Texas, they’re made of Krayton, a soft yet durable material, and offered 

in Sparkle Red, Sparkle Blue, White, Black & Tan to match just about 

any color scheme ya got going! Coolest thing of all… there are 4 styles 

available with trick polished billet end caps! Fit all models 74-12 (except 

08-12 Touring models and models with handlebar air reservoir). Left side 

grip is 1” I.D. and the right side grip is 1 1/8” I.D. for use with throttle 

assembly. Sold in pairs. Made in Texas, USA by our friends at Avon Grips. 

632820 Old School grips w/end Cap. Sparkle Red. Pair . . . . . . .$29.99 

632821 Old School grips w/end Cap. Sparkle Blue. Pair. . . . . . .$29.99 

632822 Old School grips w/end Cap. White. Pair . . . . . . . . . . . .$29.99 

632823 Old School grips w/end Cap. Black. Pair . . . . . . . . . . . . .$29.99 

632824 Old School grips w/end cap. Tan. Pair . . . . . . . . . . . . . . .$29.99 

632830 Old School grips Sparkle Red. Pair . . . . . . . . . . . . . . . . . .$22.99 

632831 Old School grips Sparkle Blue. Pair. . . . . . . . . . . . . . . . . .$22.99 

Jammer Vintage Style Colored Handlebar Grips 

For late Big Twins and Sportster models from 74-12 (except 08-12 Touring models and models with handlebar air reservoir). Left side grip is 1" 

I.D. and the right side grip is 1 1/8" I.D. for use with throttle assembly. Now available in natural, black, red and white versions! A great look when 

matched with our "Slim Line" or "Old School" solo seats, EZ P-Pads, bicycle style kicker pedals and floorboard mats! Sold in pairs. 

111122 Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

111118 White. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

632339 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

632358 Natural . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $29.99 

NOTE: Use CC #111170 throttle housing assembly (single pull) or CC #111169 (dual cable push/pull) with these grips if you do not have an existing throttle housing. 

111169 Dual cable assembly for all 81 models and custom applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

111170 Single cable assembly for all models from 74-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

22 


651828 

111169 

111192 

Chrome Throttle Assemblies 

Replacement 1" throttle assemblies with adjusting screw. Available 

for single cable or dual cable models from 73-81. They also work on 

custom applications. 

111170 Single cable assembly for all models from 74-80 . . . . . . . . . .$9.99 

651823 Single cable assembly for all models from 74-80, black . . . .$8.99 

111169 Dual cable assembly for all 81 models and custom applications 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$9.99 

651822 Dual cable assembly for all 81 models and custom applications, 

black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$8.99 

111193 

651825 

Throttle Clamp Sets 

Chrome die-cast clamp sets include the upper and lower clamp with 

screws. Available for single or dual cable applications. 

111192 Chrome, single cable clamp set. . . . . . . . . . . . . . . . . . . . . . . $9.99 

651827 Black, single cable clamp set . . . . . . . . . . . . . . . . . . . . . . . . . $7.49 

111193 Chrome, dual cable clamp set . . . . . . . . . . . . . . . . . . . . . . . . $9.99 

651828 Black, dual cable clamp set. . . . . . . . . . . . . . . . . . . . . . . . . . . $7.99 

111206 

Custom Throttle Clamps 

These custom throttle clamps from Custom Chrome hold the throttle 

sleeve in place on the handlebars and feature smooth styling and a 

deep chrome finish. Includes upper and lower clamps with hardware. 

111206 Fits single cable 5/16" (81-95) . . . . . . . . . . . . . . . . . . . . . . . . . .$14.99 

651826 Black, single cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7.49 

111207 Fits dual cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$14.99 

651825 Black, dual cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7.49 

Replacement Nylon Throttle Pipes 

Available with a single cable attachment to fit most models from 

73-80, or for the late-model dual cable assembly attachment that fits 

most models from 81-12 (except 08-12 Touring models). 

12880 Throttle pipe for single cable . . . . . . . . . . . . . . . . . . . . . . . . . . .$2.99 

12889 Throttle pipe for dual cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . .$2.99 


110943 

110961 651847 

110944 

Oval Custom Mirrors 

Fits left or right side on most models. Sold each. 

110943 Long stem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $14.99 

110944 Short stem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $14.99 

Custom Mirror Clamp 

This chrome die-cast 2-piece clamp fits all 1" handlebars and is ideal for mounting 

mirrors, turn signals and other accessories using 5/16" mounting bolt. 

110961 Chrome, sold each . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $7.99 

651847 Black, sold each. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $7.99 

651841 

651839 

12393 

Rectangular Mirror 

Mirror head measures 2” x 4 1/4”. Comes 

complete with mounting hardware. Sold 

each. 

12393 Chrome, Rectangular mirror . . $9.99 

651841 Black, Rectangular mirror. . . . . .$8.99 

651846 

12259 

12260 

12363 

Late-Style Short Stem 4"-Round Mirrors 

Add classic styling to your late-model bike with our 

chrome-plated 4"-round mirrors. They fit all models and 

feature threaded stems that come complete with all 

required mounting hardware. Sold each. 


12259 Left-side (replaces OEM 91931-92T). . . . . . . . $14.99 

12260 Right-side (replaces OEM 91930-92T) . . . . . . $14.99 

Black 

651840 Left-side, black (replaces OEM 91931-92T). . $12.99 

651839 Right-side, black (replaces OEM 91930-92T) $12.99 

12395 

12394 

Custom Round Mirrors 

Custom 3" or 4"-diameter round mirrors 

complete with 3" stems. These mirrors will 

fit the right or left side of all models. 

12394 3" mirror. . . . . . . . . . . . . . . . . . . . .$9.99 

12395 4" mirror. . . . . . . . . . . . . . . . . . . .$14.99 

12392 Optional 8"-long stem (pack of ten) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$21.99 

Stock Replacement 

Mirror 

Stamped steel body. Fits right 

and left side. Replaces OEMs 

91875-77, 91878-77 

12363 Chrome, sold each 

. . . . . . . . . . . . . . . $9.99 

651846 Black, sold each. . $8.99 

24 


Flexible Chrome Wire and Cable 

Cover 

This flexible chrome cover has a 3/8” I.D. 

and comes in a 58” length. Great for routing 

custom wiring or use in protecting cables/ 

hoses. Can be easily cut to fit. 

110900 Flexible chrome wire & cable cover 

. . . . . . . . . . . . . . . . . . . . . . . . . . . .$16.99 

Chrome Cable Wrap 

A classic 50’s-style ‘Dresser’ trim item. 

Available in 5-foot lengths (150 cm) and 

your choice of two diameters. 

84238 3/16" (5 mm) cable wrap . . . . . .$6.99 

84239 5/16" (8 mm) cable wrap . . . . . .$8.49 

Speedometer and Tachometer 

Cables 

Front Wheel Speedometer Cables 

Fits all FX 73-85 (except FXWG, FXST); 84-92 

FXRS (except Sport Edition, Convertible, 

FXRT and Low Rider models with tankmounted 

instruments); XLH and XLCH 73 

only; XLX 83-85 and XLH 84-85. Also fits 

Sportster models from 86-10 (replaces OEMs 

67051-73, 67052-78A) 40 1/4".5/8“+16mm. 

19082 Black vinyl. . . . . . . . . . . . . . . . . . .$16.99 

310495 Stainless steel. . . . . . . . . . . . . . . .$18.99 

Fits 83-85 XLS; 84-93 FXRT and FXRS Sport 

Edition or Convertible models; 73-85 FX 

(except FXWG, FXST) with 2" to 4" over 

stock length forks (replaces OEM 67054-83) 

46" 

19083 Black vinyl. . . . . . . . . . . . . . . . . . .$18.99 

Fits all front wheel driven CC mini-speedos 

and mini-speedo kits. Also fits XLH and XLCH 

74-83 and 84-93 FXWG, FXST and FXSTC 

(replaces OEMs 67051-74, 67024-84 and 

67038-84) 38 1/2" 

19084 Black vinyl. . . . . . . . . . . . . . . . . . .$15.99 

Fits 82-83 FXR and 79-82 XLS plus any of 

the applications for CC #19084 with 2" to 

4" over stock length forks, including CC 

mini gauges (replaces OEM 67060-79A) 

40".12mm. 

19085 Black vinyl. . . . . . . . . . . . . . . . . . .$16.99 

Fits same applications, including CC mini 

gauges, as CC #19084 but for use on bikes 

with 6" to 8" over stock length forks 47 1/2" 

27851 Black vinyl. . . . . . . . . . . . . . . . . . .$16.99 

Fits FL model 37-61 (repl. OEM 67026-37) 

36" 

14697 Black vinyl. . . . . . . . . . . . . . . . . . .$22.99 

Fits XLX/XLCH 70-72, (repl. OEM 67051-70) 

44" 

14702 Black vinyl. . . . . . . . . . . . . . . . . . .$19.99 

Front Wheel Speedo Cables (continued) 

Fits FLHT/FLHTC/FLHTP 86 (repl. OEM 67060-86A) 

44 1/2" 

14674 Black vinyl. . . . . . . . . . . . . . . . . . . . . . $16.99 

Fits XLH883/883DLX/883 Hugger 91-94, XLH1200 

93-94, XLS late 84-85, FLHT/FLTC/ FLTCU/FLTCUI 

96-10, FXRS Conv. 90-94, FXRS-SP 87-93, FXRT 85 

(repl. OEMs 67060-96, 67063-89) 41" 

14723 Black vinyl. . . . . . . . . . . . . . . . . . . . . . $29.99 

FXEF 1985 (repl. OEMs 67077-84, 67077-85) 

36".5/8“+16mm. 

14686 Black vinyl. . . . . . . . . . . . . . . . . . . . . . $16.99 

Fits FL models 81-84, FLHS 87-94 FLST 86-90, 

FLSTC 87-95, FLSTF 90-95, FLSTN 93-95, FLTC 

87-91, FLTCU 89-95 FLTCUI 96, FXDB-D 92, 

FXDB-S 91, FXDC 92, FXDL 93-94, FXRS 88-92 

(repl. OEMs 67079-86A, 67186-88, 67072-87A/B 

and 67026-81) 35".12mm. 

19165 Black vinyl. . . . . . . . . . . . . . . . . . . . . . $14.99 

Fits all models with 2:1 ratio speedometer and 

front wheel drive, 84-10 FXWG/FXST (repl. OEM 

78083-84) 42 1/2" 

19095 Black vinyl, 42 1/2"-long . . . . . . . . . $22.99 

Transmission Drive Speedometer Cables 

27852 Fits all transmission-driven CC mini 

speedometers and mini-speedo kits 53" 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $17.99 

14693 Fits FLS, XL models with mini gauge, 

transmission drive, 47 1/2" . . . . . . . $17.99 

19086 Fits all 62-80 FL models, 71-72 FX models 

and 80-83 FXWGs, as well as 54-72 

XL models when using CC #25575 onepiece 

Fat Bob tank. Can be used with 

any of CC’s large dash-mounted 1:1 

speedometers (repl. OEM 67026-62) 35 

1/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . $17.99 

Tachometer Cables 

Fits all XL 74-80 and FL 61-69 with distributor 

drive. Also fits CC #27820 & 27863 mini tachometers 

and mini-tach kits (replaces OEMs 92065- 

74T, 92062-65A) 32" 

27850 Black vinyl. . . . . . . . . . . . . . . . . . . . . . $15.99 

Clutch Cable Bracket 

Attaches to the stock oil tank, and holds 

the clutch cable in place. Fits Big Twins from 

65-E79. 

19080 Replaces OEM 62576-65TA . . . .$11.49 


Control Cable Ferrules 

These hard to find cable ferrules fit idle or 

throttle cables on Big Twins and Sportsters 

74-12 with stock type twist grip. 

040740 Sold in a pack of 10 . . . . . . . . . . .$5.49 

Cable Oiler 

Designed to direct lubricant into the cable 

core, not on the shop floor. Fits most throttle, 

clutch and brake cables. 

400591 Sold each . . . . . . . . . . . . . . . . . . . .$7.99 

Speedometer Extension 

3" extension helps clear brake calipers and 

eliminate kinks. Speedo rubber boot sold 

separate. (Not for Motion Pro Cables) 

59111 3" speedo extension . . . . . . . . .$12.99 

Custom Black Vinyl Front Wheel 

Speedometer Cables 

Unique cables that permit you to combine 

any of our large 2:1 ratio Fat Bob speedometers 

with front wheel speedometer 

drive units. Each cable is complete with two 

cable-to-speedo head nuts, and a speciallydesigned 

flared cable end to fit either the FL 

(5/8"-18 large coarse thread) or 82-94 (16 x 

1.0mm) metal cased speedometers fitted to 

Sportster, FX and FXR models. 

19081 38 1/2"-long . . . . . . . . . . . . . . . . .$22.99 

19095 Black vinyl, 42 1/2"-long . . . . . .$22.99 

Choke Cables 

Replacement black vinyl choke cables. 

14700 Fits XL 88-91, FLST/FXST 90-97, FLHT 

90-97, FXRS/T 90-92, FXDL/FXDWG 

93-97, FLHR 94-97, FLHT 95-97, FX 

95-97 (repl. OEMs 29236-90, 329229- 

88A, 29229-88) . . . . . . . . . . . . . .$12.99 

14722 Fits FLTC 80-89, FLHT 83-87, FXRS 

82-89, FLHTC 83-89, FLHTCU 89, 

FLHS 87-89, FXRP 84-88, FLHTP 

84-88, FLT 80-83, FXRC 85/87, 

FXRD 86, FXRDG 84, FXLR 87-89, 

FXR 82-83/86-89, FXRS-SP 85-89, 

FXRT 83-89 (repl. OEMs 29209-86, 

29225-79) . . . . . . . . . . . . . . . . $20.99 

These fine Jammer products are found in 

the 2013 Custom Chrome Catalog 

26 


General Warnings 

Motorcycle riding is a dangerous activity. The only way to be sure to avoid 

injury is not to ride! Even if you use the finest and best-maintained equipment, 

wear a helmet and protective clothing, and take all possible precautions, it 

is not possible to avoid every risk. Motorcycle accidents frequently result in 

serious injury, including death. Please do not operate a motorcycle or other 

motor vehicle when you are tired or under the influence of alcohol or drugs, 

or when your perception is impaired for any other reason. At all times, please 

wear a helmet, ride carefully and within posted speed limits, and obey all other 

traffic regulations and instructions from law enforcement personnel. 

Custom Chrome, sells aftermarket motorcycle parts for Harley-Davidson ® and 

other brands. If you do not have the necessary experience and skill, please have 

a qualified mechanic install any new or replacement part on your motorcycle. 

The failure to install properly and test any new or replacement component 

could adversely affect your motorcycle’s operation and result in an accident, 

including a fatal accident. 

Federal and state laws and regulations impose restrictions on modifying the 

engine, ignition, exhaust and other components of a motorcycle intended 

for on-road use. In addition, these laws and regulations impose requirements 

on windshields, brake components, lighting, and other equipment on your 

motorcycle. Accordingly, certain parts in this catalog are for competition or 

display purposes only. In general, those parts are indicated by a “Competition” 

mark: a checkered flag in a yellow oval. 

If you are a retail customer, you are responsible to know the laws and 

regulations that govern the modification of your motorcycle. Custom Chrome is 

not responsible if you modify your motorcycle or any component in violation of 

law. If you have any questions regarding a particular component, please consult 

your dealer or a qualified motorcycle mechanic. 

The following is additional information relating to components for sale in 

various sections of this catalog. This information is not exclusive – if you have 

any questions regarding the installation or use of any component, please 

contact your dealer, a qualified mechanic, or Custom Chrome’s customer 

service department. 

© COPYRIGHT 1982-2013 BY CUSTOM CHROME - A DIVISION OF DAE-IL USA, INC. 

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED, 

STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY 

ANY MEANS; ELECTRONIC, MECHANICAL, PHOTOCOPYING, RECORDING, OR 

OTHERWISE WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER. 

Any “add-on” or “modified” emissions-related parts contained in this brochure that are subject to anti-tampering laws may or may not have been evaluated and/or 

exempted by CARB. As a distributor, Custom Chrome makes no representation or warranty with respect to whether the emissions-related parts in this brochure are 

legal for sale, installation or use in any state unless the part is installed in a vehicle used only for closed-course competition. Consult with the manufacturer as to any 

such exemptions before purchasing any add-on or modified emissions-related parts for non-competition use in California or elsewhere. 


World’s Finest Products For Harley-Davidsons 

Service 

Maintenance 

Customization 

Repair 

Performance 

18225 Serene Drive | Suite 150 | Morgan Hill, CA 95037 | Printed in USA 

28

Hand Controls - Custom Chrome

Create successful ePaper yourself

Delete template?

Save as template?