Wallmount LS321LED Pagoda - Lumascape

Transformers, Power Supply & Driver CompatibilityTechnical DataTransformers and Power Supplies for Low Voltage LED LuminairesThe following list of transformers and power supplies are for use with luminaires specifically described as being compatible with either 12 V AC (wirewound only)transformers or with 12-24 V DC power supplies. Compatibility will be noted in the ordering code of the luminaire concerned, and will typically be referenced by VoltageCode '13' or '13-DIM'. In the case of '13-DIM' additional components may be required. Refer to the applicable wiring diagram/s.Compatibility with each transformer or power supply is indicated by the value mentioned, representing the maximum number of luminaires that may be poweredfrom each transformer or power supply. Please note, this does not take into consideration voltage drop or ampacity limits of the branch circuit. For assistance, pleasecontact factory.Wall Mounted Landscape Lighting TransformersWall Mounted TransformersClass 2 PowerSupplyDirect BurialTransformerLS-TWM-1-300 LS-TWM-2-600 LS-TWM-3-900 LS-TWM-50 LS-TWM-100 LS-TWM-150 LS-TWM-250 LSLED-24V96W277 LS-TDB1-300Input Voltage 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120 V, 60 Hz 120-277 V, 50/60 Hz 120 V, 60 HzOutput Voltage 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 24 V DC 12.5 V, 60 HzWattage 1 x 300 W circuit 2 x 300 W circuits 3 x 300 W circuits 50 W 100 W 150 W 250 W 96 W 300 WLS321LED 23 46 69 3 7 11 19 9 23Remote, Constant-Current Drivers for LED LuminairesGenerally speaking, the use of a remote driver is undesirable, except in some specific situations such as when the driver can be housed immediately adjacent to eachluminaire (i.e. in the junction box the luminaire is mounted to), or when a luminaire has no option for a driver to be placed within the luminaire itself. The term “driver”here refers to a device that directly powers the LED inside the Luminaire. The 'driver' requires that luminaires be wired in series. This device will put out a 'constantcurrent', which is required by the LED itself.The following list of drivers are for use with luminaires specifically described as requiring a remote constant current driver. Compatibility will be noted in the orderingcode of the luminaire concerned, and will typically be referenced by Voltage Code 'RE', (i.e. 'remote').Compatibility with each driver is indicated by the value shown in the table, representing the maximum number of luminaires that may be powered from each driver.Please note, this does not take into consideration voltage drop or ampacity limits of the branch circuit. For assistance, please contact factory.Remote DriversNON-DIMMABLEDIMMABLELS6094-350 LS6094-700 LS6097-1100 LS6097-850 LS6097-1100-DIM LS6097-850-DIMInput Voltage 120-277 V, 50/60 Hz 120-277 V, 50/60 Hz 120-277 V, 50/60 Hz 120-277 V, 50/60 Hz 120-277 V, 50/60 Hz 120-277 V, 50/60 HzDrive Current 350 mA 700 mA 1100 mA 850 mA 1100 mA 850 mAControl Options 0-10 V 0-10 VLS321LED 1www.lumascape.com