Countertop Cooking Equipment - Greenfield World Trade

vollrathco.comSteam Table Pans and AccessoriesSuper Pan V withNon-Stick Interior 22 gauge 300 series stainless steel Dramatic black interior enhances both cold and hot food presentations Triple bonded layer coating is the finest available Cook, serve and display in the same pan Interior surface is stain resistant Temperature tolerance of -20˚ to 450˚ F (-28˚ to 230˚ C) Dishwasher safe Not for use with metal utensilsPANSIZEITEMDEPTHIN (MM)BRIMFUL CAPACITYQT (L)CASELOTPANSIZEITEMDEPTHIN (MM)BRIMFUL CAPACITYQT (L)CASELOT1/1 70012 1 1 ⁄2 (40) 3.9 (3.7) 670022 2 1 ⁄2 (65) 8.3 (7.9) 670042 4 (100) 14 (13.3) 62/3 70122 2 1 ⁄2 (65) 5.6 (5.3) 61/2 70212 1 1 ⁄4 (35) 2.1 (2) 670222 2 1 ⁄2 (65) 4.3 (4.1) 670242 4 (100) 6.7 (6.3) 62/4 70522 2 1 ⁄2 (65) 3.7 (3.5) 670542 4 (100) 5.7 (5.4) 61/3 70322 2 1 ⁄2 (65) 2.6 (2.5) 670342 4 (100) 4.1 (3.9) 670362 6 (150) 6.1 (5.8) 61/6 70622 2 1 ⁄2 (65) 1.2 (1.1) 670642 4 (100) 1.8 (1.7) 670662 6 (150) 2.7 (2.5) 6Super Pan V Flexible Pan Lids Low-density polyethylene Translucent lids allow stackingfor easy storage Sanitary and easy to clean Non-staining and dish-washer safe Safe to use in temperaturesranging from -20˚F to 190˚F(-28˚C to 88˚C) Ideal for cold food storagePAN SIZE ITEM CASE LOT1/1 52430 61/2 52431 61/3 52432 61/4 52433 61/6 52434 61/9 52435 6Note: For use with Full Size Super Shapes SteamTable Pans, see page 6-3 & 6-4Flange and Opening Sizes forSuper Pan V Steam Table Pans“A”FLANGEOPENINGPAN SIZE “A”: IN (CM) “B”: IN (CM) LENGTH: IN (CM) WIDTH: IN (CM)Full 20 27 ⁄32 (52.9) 12 25 ⁄32 (32.5) 19 3 ⁄4 (50.2) 11 11 ⁄16 (29.7)“B”OPENINGWIDTHTwo-Thirds 13 29 ⁄32 (35.3) 12 13 ⁄16 ( 32.5) 13 (33) 11 15 ⁄16 ( 30.3)Half 12 5 ⁄8 (32.1) 10 5 ⁄16 (26.2) 11 7 ⁄8 (30.2) 9 9 ⁄16 (24.3)Half-Long 20 27 ⁄32 (52.9) 6 7 ⁄16 (16.4) 19 13 ⁄16 ( 50.3) 5 3 ⁄8 (13.7)Third 12 5 ⁄8 (32.1) 6 27 ⁄32 (17.4) 11 7 ⁄8 (30.2) 6 1 ⁄8 (15.6)Fourth 10 9 ⁄32 (26.1) 6 9 ⁄32 (16) 9 9 ⁄16 (24.3) 5 9 ⁄16 (14.13)Sixth 6 27 ⁄32 (17.4) 6 9 ⁄32 (16) 6 1 ⁄8 (15.6) 5 9 ⁄16 (14.1)Ninth 6 7 ⁄8 (17.5) 4 1 ⁄4 (10.8) 6 3 ⁄16 (15.7) 3 9 ⁄16 (9)OPENINGLENGTH Tolerances on opening dimensions are + 1 ⁄16", -0"; Flange dimensions (“A” and “B”) are ± 1 ⁄32"; Note: Corner should be 1 ⁄4" to 7 ⁄8" radius6-8