EPIPHANY - P8ntbox

More documents

Recommendations

Info

BALL DETENTSINSPECTION, CLEANING AND REPLACEMENT01 02 03 04 05Degas and disassemblethe marker (seedisassembly section.)Look into the body breech.The tip of each ball detentshould extend approximately1/16 of an inch intothe breech area. If eitherdetent does not reachthis far into the breech, itshould be replaced.To avoid risk of eyeinjury, even while wearinggoggles, do not look intothe barrel or breech of anassembled marker.Reach a finger into thebody breech and pressout against the detent. Itmay then be removed byprying or gripping withfingernails, needle-nosedpliers, an o-ring pick or evena 0.050-inch allen wrench.Inspect the ball detents fortears or damage. If they aredamaged, replace them. Ifnot, clean them with a softcloth, and clean the detentopenings in the body breechwith a cotton swab.Reinstall the detents bypressing them into placewith a thumb.Reassemble the marker.FIG. 22PRYING OUT DETENT20800.922.2147 www.smartparts.com
TROUBLESHOOTINGIMPORTANTEPIPHANY IS LEAKING INTERNALLY.— Pneumatic hoses may be loose, damaged or not fully connected. Replace hoses with Smart PartsEpiphany hoses only.— One or more of the banjo fittings may be loose or have a damaged seal. Inspect and tighten fittings.Replace if necessary with Smart Parts Ion/Epiphany banjo fittings only.— Solenoid armature is damaged or overpressurized. Make sure operating pressure is under 280psi. Inspectsolenoid valve and replace armature if necessary.— Incorrect solenoid valve may be overpressurized. The Epiphany and Epiphany rated Blackheart solenoidvalves can be identified by a red protective wrap with a black Ion logo. Standard Ion/SP-8 (no coilwrap,) Pre-Epiphany Blackheart (black wrap with red logo) or after-market solenoid valves may not functionproperly in the Epiphany’s pressure range.EPIPHANY IS LEAKING DOWN THE BARREL.— One or more of the bolt o-rings and/or the bolt stop o-rings are damaged. Inspect and replace.EPIPHANY IS LEAKING FROM THE MACROLINE AIR FITTINGS.— Macroline may not be fitted properly. Degas the marker and make sure the macroline is properlylocked into its fittings. If the macroline shows signs of damage, replace it with a new piece. Be sure tocut clean ends, and if using diagonal cutters, dress the end with a small needle file to be certainit is not crimped partially closed.EPIPHANY IS LEAKING FROM IN OR AROUND THE REGULATOR.— The ASA o-ring at the top of the regulator may be damaged. Remove the regulator to inspect. Ifthis o-ring is damaged it may be replaced with a standard CO 2bottle o-ring available at mostpaintball shops.— The regulator seat may be contaminated and/or damaged. Inspect and clean the regulator seat(see Regulator section of this manual.) If the regulator seat is damaged, it may be flipped over touse the back side. If both sides are damaged, it must be replaced.EPIPHANY EXHIBITS FIRST SHOT DROP-OFF (FSDO).— FSDO is a low velocity, or non-firing first shot followed by normal shooting, and is often caused bydebris in the bolt or a poorly lubricated bolt. Clean the bolt, body breech, fire chamber and boltstop, and lubricate them with SL33K (See the Disassembly section of this manual.)— FSDO can also be caused by too low of a dwell setting. Follow the procedure for optimal dwell adjustmentand or increase the dwell setting (see the Electronic Adjustment section of this manual.)800.922.2147 www.smartparts.com21
Page 3 and 4: TABLE OF CONTENTSQuick StartGetting
Page 5 and 6: BARREL BLOCKER/HOPPERPLEASE READ CA
Page 7 and 8: GASESPLEASE READ CAREFULLYTwo easy
Page 9 and 10: PAINT/VELOCITYPLEASE READ CAREFULLY
Page 11 and 12: ELECTRONIC ADJUSTMENTIMPORTANTSETTI
Page 13 and 14: ROF DELAY/FIRING MODESROF DELAYThe
Page 15 and 16: EPIPHANY PARTSIMPORTANTFIG. 16MAJOR
Page 17 and 18: DISASSEMBLYDISASSEMBLY CONTINUED040
Page 19 and 20: EPIPHANY VOLUME INSERTSIMPORTANTIn
Page 21: REGULATORNote: When removing or ins
Page 25 and 26: TROUBLESHOOTINGIMPORTANTEPIPHANY’
Page 27 and 28: CPS TABLEThis table provides a cros

EPIPHANY - P8ntbox

Create successful ePaper yourself

Delete template?

Save as template?