SHORTSTOPP® II 8X10 Inch Data Sheet - T.D. Williamson, Inc.

Data Sheet No.SSII-8x10®SHORTSTOPP II 8” x 10” ReducedBranch Plugging Machine(2-1/2” Dia. Control Bar)Data Sheet No. SSII-8x10Date: September 2004Supersedes: December 2003TappingT-203 Tapping Machinewith air motor driveassembly and carryingcase.Stock No. 05-2173-0000Reference Bulletin2100.007.00Plugging8” x 10” Plugging Machine Assembly08-3501-0810Includes items belowControl Bar Assembly08-3389-0000Bleeder Valve AccessoryPurchased separately1/4” Bleeder Valve00-0774-0001Nipple00-0220-0001 (Note 4)Data Sheet No. SSII-8x10Jack Assembly08-3367-00008” x 12” Completion Plug Holder08-3397-0000Housing Assembly08-3350-0000Sight Glass Kit 08-3424-0000-02 (Note 3)See Sight Glass Data Sheet for detailsInstruction Manual, 4”-12”Pub. No. 00-3795-0201Valve Adapter06-1544-0000Standard Plugging Head Assembly08-3330-0000Includes items below8” SHORTCUTT ® Valve09-0042-0000275 psi MWPCutter Holder05-0326-00008” SHORTSTOPP ® Cutter(nominal)05-0330-0008Chip Sweep (see Note 6) or Sight GlassSealing Element Not Included (Note 8)Nosepiece08-3330-0004 and08-3330-1504 (Note 8)8” x 10” SHORTSTOPP ®Welding Fitting06-9543-0000 (Note 5)8” Valve-to-Fitting Adapter06-5724-00038” x 10” 3-WAY Tee06-7241-0810-01Standard Outlet06-7241-0810-02Thinwall Outlet(Note 5 and Note 6)Pilot Drill05-0293-001110” Steel PipeRefer to back forfitting options.Notes1. Maximum Working Pressure and Temperature: 150psi at 100°F or 120 psi at 180°F. Special cups and/ornosepieces may be required (see chart at right).2. Use 8” x 10” Pilot Drill 05-0293-0011 for reducedbranch taps. With 660/760 Tapping Machine use 8” x 12”Tapping Adapter 06-6102-0017.3. Sight Glass Kit - Requires the use of the 8” T-203Tapping Adapter. Part No. 06-1544-00004. Bleeder valve and nipple are provided with TDW DrillingMachines.5. Fitting - Leaf-type completion plug and blind flangeincluded.6. 8” Plugging Head Kit adapts folding head plugger toplug 8” size-on-size lines and 3-WAY Tee Outlet. Kit08-3420-0000 includes Plugging Head Assembly08-3320-0000, chip sweep, and adapter.7. With an 8” x 12” Plugging Head, Nosepiece and Cup,12” pipe can be plugged. (See 8” x 12” Data Sheet.)8. Sealing Elements - Refer to chart at right.150 psi MWP 150 psi MWPPipe ID Sealing Element Nosepiece10.250-10.375 08-2332-0010-00 08-3330-150410.062-10.188 08-2332-0010-01 08-3330-15049.938-10.020 08-2332-0010-02 08-3330-00049.688-9.875 08-2332-0010-03 08-3330-0004Consult factory for unlisted Pipe ID’s.T.D. Williamson, Inc. P.O. Box 3409 Tulsa, Oklahoma 74101-3409 918-447-5000 Fax: 918-447-5154 www.tdwilliamson.comData subject to change without notice. / Dimensions not for construction unless certified. / ® Registered trademark of T. D. Williamson, Inc. in the United States and foreign countries / TM Trademark of T. D. Williamson, Inc. / © Copyright 2006. All rights reserved T. D. Williamson, Inc. / Printed in USA

Data Sheet No. SSII-8x10Fittings®Tapping and SHORTSTOPP II Plugging Machine8” x 10” Gas MainData Sheet No. SSII-8x10Welding FittingSee Bulletin 2100.003.003-WAY TeeSee Bulletin 2100.002.00Branch Type II 3-WAY TeeSee Bulletin 2100.011Branch Type II Plugging FittingSee Bulletin 2100.010Note: Consult your TDW representative for additional fitting options.T.D. Williamson, Inc. P.O. Box 3409 Tulsa, Oklahoma 74101-3409 918-447-5000 Fax: 918-447-5154 www.tdwilliamson.comData subject to change without notice. / Dimensions not for construction unless certified. / ® Registered trademark of T. D. Williamson, Inc. in the United States and foreign countries / TM Trademark of T. D. Williamson, Inc. / © Copyright 2006. All rights reserved T. D. Williamson, Inc. / Printed in USA