Views
2 years ago

Admin. Guide Vol. 2 - NC State Remedy Implementation

Admin. Guide Vol. 2 - NC State Remedy Implementation

vServerThreads/ProcessesTCD ServerFirst fast serverSecond fast serverFirst list serverSecond list serverThird list serverFourth list serverFifth list serverPortNumbers1010Administration server 102099799810021003100410051006RPCProgram Number390604390600390620390621390635390636390637390638390639Notification server 1050 390601Figure 3-8Example Port Numbers Assigned to ServersIf you had assigned list servers to port 998, the ports assigned to your fastservers and list servers would conflict because the second fast serverwould expect to use port 998. Verify that your port numbers are correct.Note:You are not required to use the TCP port numbers in sequence(except for fast and list server ranges).4. Save the ar configuration file.5. Start the AR System server.6. If you are using Windows NT and thread logging is activated, view the\db\arthread.log file to verify that the AR Systemserver threads have started successfully.➤Assigning a Port Number to a Notification Server1. Stop the notification server.2. If you have not done so already, create the nfy configuration file.■■On UNIX, create the nfy.conf file in the etc directory.On Windows NT, create the nfy.cfg file in the conf directory.3-24 Action Request System Administrator’s Guide, Volume 2

Configuring Clients3. Open the nfy configuration file.4. Enter the port number in the following format:TCD-Specific-Port: 1010Notifier-Specific-Port: 1050Register-With-Portmapper: FDo not assign port numbers that conflict with port numbers used by otherapplications or programs running on your system, because your serversmight not start as expected. To find out which port numbers are already inuse, use the rpcinfo -p command (UNIX) or the netstat -a command(Windows NT) at the command line prompt.5. Save the nfy configuration file.6. Start the notification server.Configuring ClientsTo access private AR System servers, client machines must have the ARRPCenvironment variable set. To avoid the portmapper when accessingAR System servers, client machines must have the ARTCPPORT environmentvariable set. To avoid the portmapper when accessing notification servers,client machines must have the NTTCPPORT environment variable set. Thissection includes instructions for configuring these variables on your clientmachines.Note:You can configure Windows, UNIX, and Macintosh clients toaccess a private server. However, you can configure onlyWindows and UNIX clients to avoid the use of a portmapperwhen connecting to a server.Windows ClientsOn Windows clients, a private server is configured in the ar.ini file. Theconfiguration to avoid the use of a portmapper is different for 16-bit systems(including Windows 95) and 32-bit systems.AR System Servers 3-25

SoundStation 2 Nortel User/Admin Guide - Polycom
Admin Guide - VoIP software provider
Guide to term sheets - BVCA admin
Implementing an Effective Academic Remediation Program: Results ...
to read. - NC State Alumni Association
to read. - NC State Alumni Association
to read. - NC State Alumni Association
to read. - NC State Alumni Association
OIG-11-32 - FEMA's Progress in Implementing the Remedial Action ...
06.Draft Phase IV Remedy Implementation Plan 12-Dec ... - Raytheon
Jim's presentation (PDF) - State Coalition for Remediation of ...
Attachment G - State Coalition for Remediation of Drycleaners
Don's presentation (PDF) - State Coalition for Remediation of ...
NC State Costal Landscaping Brch.indd - Herbarium - North ...
Implementation Guide - FSAdownload.ed.gov
Implementation Guide - FSAdownload.ed.gov
16440-admin-guide-and-entry-codes-14-19-qualifications-2012-13
to read. - NC State Alumni Association - North Carolina State ...
Vol 33, No. 2 - NAWC
Vol 39, No. 2 - NAWC
Vol 22, No. 2 - NAWC
Abhidharmakosabhasyam, vol 2
Bioinformatika, Vol.:2 No. - NIST