Views
2 years ago

Gunsmith Series - GD & GHD - Savage Range Systems

Gunsmith Series - GD & GHD - Savage Range Systems

Savage

Savage Range Systems, Inc.Model GD / GHDV. TROUBLESHOOTINGProblem Probable Cause Possible SolutionNo water flow Pumps not turned on Switch on pumpsPoor water coverage / LowFlowNo power to pumpsPump is not workingLow water levelEnsure pumps are plugged inCheck circuit breakerCheck power supplyPlug pump into socketReset pump – SeeManufacturer’s manualReplace pumpPump is not working No power to pump Check plugPump has overheated andtripped outFaulty pumpAdd water until level to topof pump housing.Check circuit breakerReset pumpLow water level – bring waterlevel to top of pumpExcessive sludge around pump– remove sludgeReplace pumpLubricating fluid is foaming Oil concentration is too high Reduce concentration byremoving some fluid andreplacing with clean waterInsufficient foaming retardant Add anti-foaming agent –contact SRS100 Springdale Road Operation & Maintenance Manual Page 6 of 8Westfield, MA 01085Gunsmith Series800-370-0712

Savage Range Systems, Inc.Model GD / GHDVI.MAINTENANCE PROCEDURESCleaning the Bullet Collection TrayDepending on the amount of material on the tray, it may be possible to simply remove the trayfrom the tank and place the spent material in the proper container. For larger amounts ofdebris, if will be necessary to remove the material from the tray using a small flat-facedshovel.1. Run the pumps for 2 – 3 minutes prior to clearing the trap to ensure that there is no drieddust on the material in the tray.2. Remove the collection tray and deposit the spent material into the chosen reclamationcontainer.Replacing a Pump1. Unplug / isolate the electrical supply to the pump.2. Remove the bullet collection tray. If necessary, remove the spent bullets from the tray asdescribed previously.3. Remove the pump from the tank.4. Loosen the hose clamp securing the vinyl tubing to the barb fitting.5. Remove the vinyl tubing from the fitting. It may be necessary to use a pair of channellocks to loosen the tubing on the fitting. Care should be taken not to damage the tubing.6. Remove the barb fitting from the old pump.7. Install the barb fitting removed above into the new pump. Attached the vinyl tubing to thefitting using the hose clamp to secure it.8. Place the pump into the tank. Run the pump to verify that the proper flow rate isobtained.9. Replace the bullet collection tray.100 Springdale Road Operation & Maintenance Manual Page 7 of 8Westfield, MA 01085Gunsmith Series800-370-0712

Gunsmith Series Bullet Traps - Savage Range Systems
Model 800D with Auger - Savage Range Systems
Specialty Bullet Traps - Savage Range Systems
Proof & Function Trap - Savage Range Systems
Model 800W with Drag Conveyor - Savage Range Systems
Steel Target Safety Guide - Savage Range Systems
KMA Overhead Target Retrieval System - Savage Range Systems
Model 800W with Bullet Collection Tray - Savage Range Systems
GeoDesy GD Systems Datasheet (PDF) - 4Gon
Restaurant Range Series Restaurant Range Series - Imperial Range
Restaurant Range Series Restaurant Range Series - Imperial Range
DIAMOND SERIES | HEAVY DUTY RANGES - Imperial Range
Series III Core Range - Amphenol
Product range - Messer Cutting Systems
Laser Range Finder Systems(.pdf)
THE PSE RANGE - PSE Power Systems
product range Messer cutting systems
Scanning Range - bei ID-Systems
09-GD-0222.Building Systems - Gwin, Dobson & Foreman, Inc.
The innovative GL 30-series planter range
Standard Series Technical Catalogue, No other range is - Clipsal
a range of cable tray systems
Pseudo-Noise (PN) Ranging Systems - CCSDS
The Intergas HRE Boiler Range - Atmos Heating Systems
Onity Product Range - ENTRY SYSTEMS, sro
Out-of-Range Settlement Prices - Commodity Systems Inc.