2 years ago

Peek 2070L Operating Manual - Quality Traffic Systems

Peek 2070L Operating Manual - Quality Traffic Systems

Section 6 — Theory of

Section 6 — Theory of Operationthis shall determine the length of the active (second) portionof the cycle. 0 = hold output state until otherwise configured.F '1' - The trigger or gate shall be acquired subsequent to filteringthe specified input. The raw input signal shall be used iffiltering is not enabled for the specified input.'0' - The trigger or gate shall be derived from the raw input.R '1' - For triggered output, the output shall be triggered by an ONto-OFFtransition of the specified input and shall be triggeredimmediately upon command receipt if the input is OFF. Forgated output, the output shall be active while the input isOFF.'0' - For triggered output, the output shall be triggered by anOFF-to-ON transition of the specified input and shall betriggered immediately upon command receipt if the input isON. For gated output, the output shall be active while theinput is ON.Input Number - 7-bit input number identifying inputs 0 Up.P '1' - The output is configured for single-pulse operation. Oncecomplete, the complex output function shall be disabled.'0' - The output is configured for continuous oscillation.W '1' - It is triggered by the specified input. Triggered complexoutput shall commence within 2 ms of the associated trigger.'0' - Operation shall begin within 2 ms of the command receipt.G '1' - Operation shall be gated active by the specified input.'0' - Gating is inactive.L '1' - The LINESYNC based clock shall be used for the time ticks.'0' - The MC shall be used for the time ticks.V '1' - Indicates maximum number of configurable outputs isexceeded.'0' - No errorNumber of items - The number of entries in the frame. If 0,all outputs currently configured as complex outputs shall bedisabled.(TEES-2002: Section input signals shall be sampled at least once permillisecond.(TEES-2002: Section • Model 2070L Operating Manual

Detailed Systems DescriptionThe “Number of Items” field is valid from 0 to 16. Zero means disableall Complex Output functions. Sixteen is the maximum because themost that is sent at one time is 8 enables and 8 disables. If processinga command results in more than 8 Complex Output functions beingenabled, none of the command shall be implemented and theresponse message “V” bit shall be set to 1. If an invalid output or inputnumber (the “G” or “W” bits being set to 1 is specified for a function,that function definition is not done by the FIOM software. It shall alsonot be counted towards the maximum of 8 Complex Output functionsallowed. The rest of the message shall be processed. When aComplex Output function is disabled, the output is set according to themost recently received Set Outputs command. When a complex outputfunction for an output is superseded, that is, redefined as witheranother Complex Output function, or as an Input Tracking function,nothing special is done with the output. The most recent value remainsuntil the new function changes it. The “G” bit (gating) set to 1 takesprecedence over the “W” bit (triggering). If gating is ON, triggering isturned OFF, regardless of the value of the “W” bit in the commandmessage. If a Complex Output is configured with the “G” bit set to 1(gating) and the “P” bit set to 0 (continuous oscillation), the output isset to OFF (0) whenever the specified input changes state so that theoscillation should cease (output inactive). For a single pulse operation(“G” bit set to 1), after the secondary duration completes the ComplexOutput function shall be disabled, and the output shall be set accordingto the most recently received Set Outputs command.(TEES-2002: Section - Configure Watchdog)The Configure Watchdog frames shall be used to change the softwarewatchdog timeout value. The Command and response frames are asfollows:(TEES-2002: Section timeout value shall be in the range between 10 to 100 ms. If thevalue is lower than 10, 10 shall be assumed. If the value is greaterthan 100, 100 shall be assumed.(TEES-2002: Section 2070L Operating Manual • 57

Installation and Operating Manual 262-30T Temperature ... - Crompton
Installation and Operating Manual System Protection Relay Energy ...
Operators and Installation Manual TR-810.pdf - Jotron
av system controller installation and operation manual - SDS Music ...
KiPro Mini Operations Manual
Transportation Operations Group - Traffic Signal Systems Committee
LTI 20.20 UltraLyte 1000 Operations Manual - Tele-Traffic
Innovator SIP Operating System and Installation Manual - 1CTI
Operating the Novus FXM - Interprovincial Traffic Services
Operating Manual - SCHNIER Elektrostatik GmbH
Traffic Signal Timing Manual - FHWA Operations - U.S. Department ...
Operational and traffic control system for the Espiye-Sarp tunnels
MX510/MX512 Operator & Installation Manual - Simrad Professional ...
Operation manual Track System TRUMPF 95 - Gerriets
Transportation Operations Group - Traffic Signal Systems Committee
Operation manual Track System ASS - Gerriets
RS25 VHF Operation Manual - English - Simrad Yachting
Operating Instructions - Operating Manuals for Panasonic Products ...
Programmable Controllers Real Time Operating System C Controller
Mountain Computer ROMPlus+ Operating Manual
Operators and Installation Manual RA-2500 AIS Receiver.pdf - Jotron