SensaLink - THORN Lighting

thornlighting.com
  • No tags were found...

SensaLink - THORN Lighting

SensaLinkIndoor Lighting Controls for interactive lightingin applications, requiring higher levels of comfort


IntroductionThorn’s Indoor Lighting Controls offer consists of three portfolios1 2 31 SensaLite features Thornluminaires with built-insensors, and remote sensors,offering stand-alone presencedetection, daylight linkingand infra-red control.SensaLite is the first step tocomfort and energy saving,and is used for small officeapplications, simpleclassrooms, corridors etc.2 ControLiteDIM is usedfor mid-sized projects (1room): The modular systemcreates scene setting,enabling daylight linkingand integrating presencedetection. It is easy tocommission by the contractor:When wiring the system, theluminaires are allocated tothe switches, scene platesand presence detectors.3 SensaLink features Thornluminaires with built-insensors and remote sensorsoffering presence detection,daylight linking and infra-redcontrol, scene setting andthe possibility to link sensors.It provides an interactinglighting management systemfor projects requiring greaterlevels of comfort.2


SensaLinkHow does SensaLinksupport the Thorn PECstrategy?Performance:SensaLink sets the right lightlevel, at the right place and atthe right time.Efficiency:SensaLink is a perfect toolto provide an efficient light.It enables you to dim theluminaires, link the luminairesto presence and link them to theincoming daylight to achieveenergy saving. Therefore lightis only provided when youneed it and in the quantity thatyou require. SensaLink alsocontinually adjusts its light outputand energy input. This maintainsilluminance over the entireperiod, saving the energy thatconventional systems waste whilefulfilling the objectives of manyinternational and local lightingstandards.Comfort:Manual dimming and presencedetection are features ofSensaLink that provide acomfortable lighting solution tothe user. SensaLink is very easy toinstall and set up. By maintainingthe illuminance level over theentire period, you will alwayshave the same light level that yourequire. Therefore the lightingremains comfortable all of thetime, without the need for regularand inconvenient re-adjustments.Additionally you can link severalzones or rooms within anapplication that interact withone another.Where is SensaLink used?The typical applications for SensaLink are:comfort of scene setting, screen and blackout blind control, e.g.lecture theatres or conference rooms that divide into smaller andindividually controlled areas.daylight and presence linked zones within each floor, e.g. openspace offices, with the possibility to link the luminaires withinthese zones and adjacent areas.FeaturesApplicationsOfficesConferenceroomsLecturetheatresClass roomsDimming and Switching Presence-link Daylight-link Luminaires interactingwith adjacent areas Distributed intelligence Scene setting Partition managementMotorised Screen control Motorised Blackout blind control 3


Overview of functions and their benefitsResponse topresence/absenceSensaLink sensor heads providepresence linking that will detectyou entering and leaving theto a pre-programmed level, and5 to 60mins. Additionally, thesystem offers a ‘semi-automatic’mode (absence detection),lighting manually (via a switch,a hand held controller or ascene plate), and the detectorwill switch or fade the lighting toleft the room. Both cases givethe possibility to dim the light toa minimum or a defined levelDimming response toincoming daylightSensaLink detectors providea dimming facility thatautomatically adjusts the lightlevel in response to the availabledaylight. You decide which lightlevel the controlling sensor shouldmaintain through the day, andif the sensor should switch thedaylight.Switching response toincoming daylightHere, dedicated SensaLinkheads, with relay output, switchthe ambient light level. Theseproducts come with an adjustablelight level.Local overrideinfra-red hand held controllerto override sensors that areresponding to the incomingdaylight – very convenient,especially in larger officeapplications, where you wantto change the lighting allocatedto one desk only, or to a groupof luminaires. It also allowsrecalling and setting six scenesfor different tasks.either the SensaLink two buttoncontrol plate or a momentaryaction switch for changing thelight level and to switch theonto the wall next to the roomentry, and therefore ideal forsmaller sized areas.You are present. Insufficient daylight. Lights on.scene plate is a versatileinterface for overriding thelight within conference roomsor lecture theatres, allowingyou to set and recall six scenesfor the different activities (see‘Scene setting’).No-one present. Lights off.You remain present. Sufficient daylight. Lights dim.You enter the room. Lights switch on.You remain present. Bright daylight. Lightsdimmed to minimum.4


Parameter setting fortailor-made functionalityThis portfolio uses an infraredprogramming tool tore-programme a wide rangeof parameters, and to set theregulating light level. This isparticularly useful in that you areable to change the parameterswithout touching the installation,and is therefore fast, hassle-freeand doesn’t disrupt the roomusers: The programming is doneremotely and hence can beoperated from the ground.Maintainedilluminance levelLight levels reduce overtime due to lamp age anddirty optics. Conventionalinstallations provide morelight than is necessary toensure that the right level isreached when depreciation isworst. This results in energywastage and unnecessarycost. Being intelligent,the SensaLink detectorscontinually adjust the lightoutput and energy input. Thismaintains illuminance overthe entire period, saving theenergy that conventionalsystems waste and fulfillingthe objectives of manyinternational and locallighting standards.IlluminanceMaintenance intervalMaintenanceIlluminance in accordancewith age and soiling of lampRequired normal illumuminanceEnergy savings through dimmingof surplus capacity5


Overview of functions and their benefitsCorridorCorridorInteraction betweenluminairesSensaLink allows sensorsto be linked. In this way,sensors “listen” to eachother and share informationabout presence/absencewithin their detection zones.This feature is useful forexample in office applications;notional corridors, staircases,and lobbies can be set toremain lit as long as one ofthe sensors is detecting apresence, providing enoughlight in the surrounding areasand giving a feeling of safety(also known as ‘corridor hold’function).Interaction with room partitionsSome applications require larger rooms to be divided into smallerseparate rooms, depending on the activities. SensaLink detects if therooms are separated or linked, and reacts accordingly: If the partitionis closed, SensaLink provides individual control within each room. Ifthe partition is opened, the combined rooms offer joined control.CorridorReliability withdecentralised functionsSensaLink keeps local functionslocal. All parameters andsettings for a specific sensorhead are stored within the unit,therefore it will continue tofunction even if the Bus systemit is connected to fails or isinterrupted. The benefit is thatpresence and daylight-link, andlocal override functions arecontinuously provided, withoutthe room user realising the lossof the Bus system.Upgrade abilityAs the SensaLink sensor headsare able to work “stand-alone”when they are not connected toa central Bus system (see also‘Reliability with decentralisedfunctions’), the possibility arisesto install them first, and tolink them, via the SensaLinkBus, in a second phase. Bydoing this, the functionality ofthe installation would initiallybe similar to several ThornSensaDigital installations,working independently fromone another, and then in thesecond stage provide all theadditional SensaLink functions.In existing SensaLinkinstallations the Bus system alsoallows you to add additionaldevices and to extend thesystem at anytime. Thisprovides you with the flexibilitythat you would expect from acontrol system, adapting to thecontinuously changing needs,uses and room layouts within abuilding.6


Blackout blind and screen controlblackout blinds and screens to be integrated within the differentscenes. SensaLink provides this comfortScene SettingFor every activity or room use you can set up to six different scenesprojection screens. This provides the comfort you expect for a lecturetheatre, a conference room and other applications that are used invarious ways. Typically Scene 1 is the daylight-linked one.Scene ‘Presentation’and daylightScene ‘Lecture’digitally projected picture,but still giving enough lightfor auditorium to take notespodiumScene ‘Break’reactivate auditorium7


System topology and components1) Starting with a multi sensor head for eachgroup of luminaires within an area…SensaLink responds to presence/absence by switching, and todaylight by dimming. Entering an area causes the lighting to cometo a pre-programmed level and the luminaires automatically adjustdepending on the natural light present.a) Thorn was among the firstcompanies to offer intelligentluminaires:incorporate a miniaturesensor capable of controllingelectronic gears, transformersand phase dimmers via a DSIsignal.Luminaire lies in the fact thatit works as soon as you takeit out of the box and installit to the ceiling. You can stillstandard mains switch, whichalso means you do not have tochange an existing installation.are possible as well, whereyou connect further luminaires(‘slaves’) to the DSI outputof the SensaLink Luminaire(‘master’). The maximumnumber of ballasts incorporatedin all controlled luminairesmust not exceed 4, andall luminaires should be inthe detection zone of theMiniSensaLink head (diameter5m at nominal mountingheight 2m above work plane,maximum mounting height 3m).Guides for Thorn SensaLink luminaires(containing ‘HFL’ in their descriptions). ‘Slave’luminaires for connection to the SensaLinkLuminaires are the standard DSI dimmableones (containing ‘HFD’ in their descriptions).MenloSoft SR with built-in MiniSensaLink headBUS2mHFLHFD5mHFDHFDOptional ‘Master-slave’ luminairearrangement (max. 4 DSI ballasts in total)Detection patternb) Remote SensaLink sensorheads enable you to control agroup of luminaires: insteadof having a ‘master-slave’arrangement as described ina). These remote sensor headsare mounted to the ceilingand control a luminaire groupincorporating up to 8 DSI ballastseach. These luminaires shouldbe in the detection zone of thesensor head (diameter 6m atnominal mounting height 2.4mabove work plane, maximummounting height 3m). You havethe choice between a recessedmounted version that is suitablefor unobtrusive installationin suspended ceilings ref.a surface mounted version forall other types of ceilings ref.The sensor incorporates a DSIoutput that is connected to the DSIdimmable luminaires via a 2-polepolarity-free lead. The maximumlength of the DSI lead betweensensor heads and luminaires canbe 12m, using standard mainswiring 2 x 1.5mm² with solidor stranded conductors, e.g.H05VV-U (harmonised standard300/500V cable, PVC insulatedand sheathed, with solidconductors).Note: All standard Thorn DSI dimmableluminaires can be controlled via remoteSensaLink heads: look for Thornluminaires containing ‘HFD’ in theInstead of controlling dimmableluminaires, there is also arecessed remote sensor head forswitching fixed output luminaires,for a maximum load of 6A,considering inrush currents ref.This sensor is connected tothe luminaires with standardmains wiring.Please refer to ‘Product parameters’for possible sensor settings.Please refer to ‘Product parameters’ forpossible sensor settings.8


Recessed remote SensaLink headSurface mounted remote SensaLink headBUSHFDHFD25mHFDHFD6mSensor connected to luminaire group(max. 8 DSI ballasts in total)Detection patternNLD1D2DSILN+BUST+–BUSDSID1D2Wiring recessed versionWiring surface mounted version9


System topology and components2) …linking these areas within rooms and floors…Within an application severalof these individually controlledareas can now be linked via theSensaLink Bus. To accomplish thistechnically, a two-wire Bus (mainsrated and unscreened twistedpair) runs from device to device,and a Bus power supply enablesthe devices to communicate witheach other and share occupancyinformation. SensaLink provides astandard Bus power supply for upup to 200 SensaLink devices ref.The Bus wiring topology canbe a ring with short spurs,radial or star like. The Bus leadmay also run alongside mainswiring, provided that the Busis suitably insulated. The mainstopology is independent from theBus topology, as the SensaLinkdevices can be mains poweredfrom different electrical circuitsand phases.HFDHFDHFLHFDHFDHFDHFLHFDHFDHFDExample for radial bus topology; maximum length of each radial 500m (300m) with 1 5mm 2 (1.0mm 2 ) conductor sizeHFDHFDHFDHFDHFDHFDHFLHFDHFDHFDHFDHFDHFDHFDHFDHFDHFLHFDHFDHFDHFDHFDSensaLinkBusMainsBUSPower Supply(LT or G)SensaLinkBusFor interconnecting all SensaLinkitems a bus lead is used: Themaximum length of this SensaLinkBus can be up to 1500m (if wiredas a ring), the cable should be1.5mm² twisted-pair unscreened.HFDHFDHFDHFDHFDHFDBUSPower Supply(LT or G)HFLHFDHFLHFDHFLHFDMainsHFDHFDHFDHFDHFDHFDHFLHFDExample for ring bus topology; maximum length of ring 1500m (800m) with 1 5mm 2 (1.0mm 2 ) conductor sizeStandard Bus power supplyBus power supply for larger applications10


3) …and connect these floors to a building backboneIn larger applications requiringseveral of the larger Bus power99 of these Bus power suppliesto a common spine or backbone(2 x 2 x 0.2mm 2 , twisted pair,screened communication cable,e.g. a RS-232 computer cable,maximum length 1200m). Sowith SensaLink large buildingscan be catered for!HFDHFDHFDHFDHFLHFDHFDHFDHFLHFDHFDHFDSensaLink BusMainsBUSPower Supply(G only)MainsBUSPower Supply(G only)SpineSensaLink BusMainsBUSPower Supply(G only)SensaLink BusMax 99suppliesMainsBUSPower Supply(G only)11


System topology and components4) User interfacesThough a properly commissioned system will providethe right light for most of the time, occasionally yourequire more or less light. SensaLink offers you theaccurate user interfaces for the different applications.Infra-red Hand held ControllerScene Select Plate, polished chrome finishLocal Control PlateAn Infra-red Hand held Controllerenables you to dim and brighten,lighting: You have the choicebetween changing the lightlevel locally and changing thelight level of the group(s) yourluminaires are allocated to. ThisInfra-red Hand held Controlleris ideal for meeting rooms andother applications that are usedin different ways, as it providesthe facility to set and to recall 6scenes for the different activitiesFor lecture theatres, conferencerooms and other applicationswith the main focus on scenesetting, SensaLink’s wall-mountedScene Select Plate is theappropriate interface. It providesscenes and for dimming andbrightening. All buttons endowyou the current setting at anytime. To match the Scene SelectPlate to different wallmaterials and colours, it isavailable in polished brass,polished chrome, brushedstainless steel and white finish,The Local Control Plate allowsto dim and brighten a group of12


5) Comissioning Tool 6) DSI and switching outputs,blind and screen control,switch inputs and interfaceto other systemsDigital ProgrammerUniversal Bus TransceiverThorn commissioning engineers set up SensaLink installations; thisservice is offered together with the luminaires and the SensaLink items.There is also the possibility to train contractors and facility managerson site, looking after the project later as well. Whoever commissions,reconfigures or changes SensaLink installations, uses the SensaLinkgroup them, to allocate control units to the groups and to define all theinteractions between the SensaLink devices. It is also used to configuretime and many others. Additionally it can be used to copy data fromone head and to use it for other ones. This device features a large LCDscreen to make it easy to use. And due to communicating via infra-redwith all the SensaLink devices, the commissioning can happen locallyand from the ground: This makes the work easy and safe, and doesnot disrupt any room users during reconfigurations.multi-functional and provides several features:incorporating up to 20 DSI ballasts, e.g. in an area where luminairesdo not need to be linked to presence or daylight.output luminaires (with magnetic or electronic gears) and non-lightingloads, e.g. screens and blackout blind motors, to be brought into theSensaLink installation.switch inputs into the system, e.g. from an external switch, timer, firealarm system or BMS, and can be configured to recall a specific All SensaLink sensors can be allocated to Global Groups: Thisgrouping structure is of less consideration to building users, but isof great importance for facility management, as it enables centraland external systems to override all sensor heads allocated to aGlobal Group. The SensaLink Transceiver is used as the interface tothese central systems: These could be central switches, or switchingBuilding Management Systems (BMS) or timers. Global Groupaddressing is typically used for load shedding, security, night andother functions.Sensor heads and SensaLink Transceiver inputs may be allocated toone of two possible Global Groups, or to both if required.system now knows if the rooms are separated or linked, and reactsaccordingly: If the partition is closed, SensaLink provides individualcontrol within each room. If the partition is opened, the combinedrooms offer joined control.13


Support of building compliance with European standardsOffice example, fully and partly occupied500lx500lx300lx300lxSensaLink supportsyour project to complywith EN 12464Norm 12464 differs from theclassical approach in which thelighting design objective wasto achieve average illuminancethroughout the room. Next tomany other criteria, the newstandard on the one handallows lighting designers greaterfreedom and designs that aremore in line with the needs ofindividuals, and on the otherdefines that lighting must bedelivered in the location wherepeople perform their visualtasks. Different maintainedilluminance levels apply forthe different work places, andthe surrounding areas wherevisual tasks are performedless often. For example fora 500lx task illuminance theimmediate surround illuminancecan drop down to 300lx.SensaLink maintains the specifiedilluminance levels, and alsochecks for you which areas areactually needed and occupied,and adapts the light output forthe unoccupied, but surroundingareas, according to the standard.SensaLink supportsyour project to complywith EN 15193This standard establishesconventions and proceduresfor the estimation of energyrequirements of lighting inbuildings. It also providesguidance on the establishment ofnotional limits for lighting energyderived from reference schemesand gives advice on techniquesfor separate metering of theenergy used for lighting that willgive regular feedback on theeffectiveness of lighting controls.Annex D (that is informative)recommends that (depending onthe application) an area withinone room, if it is illuminatedby a luminaire or by a groupof luminaires (manually orautomatically) switched together,should not be larger than 30m 2 .In addition, in the case of systemswith automatic presence and/or absence detection the areacovered by the detector shouldclosely correspond to the areailluminated by the luminaires thatare controlled by that detector.As lighting controls system basedon a network of multi sensorheads, SensaLink is the idealtool to realise the recommendedway of linking luminaires todaylight and presence/absencefor each area within a room,and therefore will support goodenergy ratings for your building.14


Product parametersTo adapt SensaLink to the local requirements, several parameters canbe set within each multi sensor head or SensaLink luminaire. These areselected during commissioning, and can be easily copied from onehead to the other to keep the commissioning time as short as possible.Power-up ConditionWhen mains power is firstapplied, sensor heads eitherfor up to 30s before lookingcorridors and access routes,other areas reduces the start-upload following any interruptionin supply.Operation ModeSet for automatic operation,the sensor head switchesautomatically. In semi-automaticmode (also called “absencemode”), luminaires remaineither via an user interface(e.g. the Infra-red hand heldController) or when anotherhead, part of the same zone, isStart LampsWhen detecting presence, lampsmaximum or minimum level,before ramping to the level thedaylight-link calculates, or thelevel set one for a recalled scene.When Vacantabove) has elapsed, lightingcan either be set to…Entry SceneAny one of the 6 availablescenes can be chosen to beactivated when presence isdetected. As scene 1 is thedaylight-linked scene, this is theDimming RangeThe daylight-link provided bya SensaLink sensor head willregulate over the full dimmingrange of the ballast’s capacity(typically between 100 and1%), to save as much energy aspossible. In certain instances aminimum light level can be set,avoiding the light level goingbelow a certain percentage.Set Light LevelThe luminaires are brightenedor dimmed until the desiredilluminance level is achieved. Thislevel is stored using the SensaLinkProgrammer. For luminaires withdimming ballasts, any lightinglevel within the operating rangeof the luminaire may be set. Thesystem automatically compensatesfor lamp deterioration andluminaire condition, andcontinually adjusts its light outputand energy input. This maintainsilluminance over the entireperiod, saving the energy thatconventional systems waste andfulfilling the objectives of manyinternational and local lightingstandards.Bright-outLights can be programmed toconditions, and to save evenmore energy. If Bright-out is notselected, the luminaire will simplyremain at minimum light outputuntil occupancy ceases or thedaylight contribution decreases.Off DelayThis is the time between the lastdetected occupancy, and whenthe lighting automatically ischanged to the chosen ‘WhenDelay options are 5 to 60min(in 5min steps), several hours,and 10s for test purposes duringcommissioning.Fade to Offluminaires dim very slowly (thefade rate is 4min/100%) beforerecommended in open-plan officecause distraction.sensor heads, provide somefurther parameters, which aredetailed in the datasheets.Following the installation ofSensaLink, the commissioning ofthe system and the setting of itsparameters is carried out locallyusing the hand-held infra-redSensaLink Programmer. Settingscan be checked at any time. Andif the requirements for lightingchange, the parameters setduring commissioning can bereconfigured quickly and easily....switch off......go to minimum output... ...continue with daylight-link, but with maximum 25% output... ...go to scene 6 (and therefore to a specified output)... ...until next occupancy...for 3 hours and thenswitch off...and switch off afterthe whole building isvacant15


Interactive lightingSOpen spaceC‘listening’BUS 1BUS 1SSSSCSSCorridor(could also bea notional one)SSSSCSSCCSensor GroupWithin a room or space, sensor heads can be allocated to SensorGroups:Sensor Group, are thus activated as soon as one of the sensor headsdetects presence.‘When Vacant’ setting).of the Infra-red Handheld Controller or any other user interfaceallocated to this Sensor Group as well.open space office, or an auditorium area within a larger lecturetheatre, sharing occupancy info and manual overrides.Groups: This feature enables to create overlapping areas if required.Common Group = Listening Sensor GroupSensor heads can alternatively be allocated to so-called CommonGroups:other sensor heads within a SensaLink installation supplied by thesame SensaLink Bus Power Supply.instead of a Sensor Group, will delay deactivating until there isvacancy in all areas.and notional corridors within open spaces, e.g. as shown in theSensor Groups within the open space detects presence.also detects absence, the sensor heads within the Common Groupsee also Building Group).be allocated to up to 4 different Common Groups. Sensor heads are allocated either to a (standard)Sensor Group, or to a (listening) Common Group.16


C ‘1’BUS 1Luminaire connected to sensorSensor allocated to:SSBUS 2SpineSSSensor Group 1Sensor Group 2CSCCSensor Group 1 and 2Common/Building Group 1Common Group 2SSCCommon/Building Group1(in another bus district)BUSBus power supply(Global one if linked via spine)ListeningCSSCCCCMain corridors on different levels with staircaseBuilding Group = Common Group 1The Common Group number 1 is a special one:Global Bus Power Supplies, are linked to a common spine, then thisCommon Group is shared within all bus districts building wide.17


Application: lecture theatreSpecification example:area lighting controlledindividuallypresenter’s area to adapttheatre to different usesto entrance to override reararea lighting if requested(when scene 1 is activated)daylight-linkedblinds integratedlinked with presence andtheatre lightingHow it works:luminaires within the lecturetheatre (Specline Alpha HFD)are connected to remoteSensaLink sensor heads,here with a maximum of 4luminaires per sensor head.not connected to a sensorhead, but uses a SensaLinkTransceiver’s DSI output.opening the blackout blindsare controlled via the switchedoutputs of two Transceivers.raising a projection screenat the front of the theatre isconnected to a switched outputof a Transceiver as well.lit by downlights (Cruz HFD),these are connected to remoteSensaLink sensor heads.together with the whiteboardlighting are allocated to threedifferent Sensor Groups: Allthree groups show differentilluminance levels when a sceneis recalled. Within SensorGroup 1 (front area) and withinSensor Group 2 (rear area)information regarding presenceis shared.projection screen form aseparate Sensor Group 4:Within the scenes they areeither closed/lowered (ideal forpresentations e.g. using digitalprojectors) or opened/raised.Plate, recessed wall mountednear to the theatre entranceis allocated to Sensor Group2, and therefore enables theauditorium users to override therear area lighting if required.Scene Select Plate is provided,also recessed wall mountednext to the presenting area: It isallocated to all Sensor Groupswithin the theatre (1 to 4) andprovides the possibility to recallsix different scenes includinglights, blinds and screen. Scene1 is the daylight-linked one.Common Sensor Group, that“listens“ to all other (standard)Sensor Groups within the samebus district: As long as theSMSMMainsSensaLink BUSSSSDSISMSSSSProjectionScreenCMains+DSICC18


lecture theatre is occupied, thecorridor and staircase lightwhole area is unoccupied.connected to the SensaLinkBus, that is powered by theSensaLink Bus Power supply.several Global Bus PowerSupplies connected to abuilding spine, the shownCommon Group 2 could bethe Building Group of anotherbus district (and would thenbe addressed as CommonGroup 1), sharing occupancydata with e.g. the corridor andstaircase lighting in all otherbus districts.DevicesRecessed luminaire (e.g. Specline Alpha HFD)Whiteboard luminaire (e.g. Optus IV HFD)Recessed downlights (e.g. Cruz HFD)MScreen/Blackout blind motor 230V ACSensor headScene select plate, allocated toSSSSLocal control plate, allocated toSTransceiver (used as DSI or Motor output)Bus power supplySensaLink Bus wire*Mains wire*DSI wire*DSI + mains wire**Standard mains wiring 1.5mm2 with solid orstranded conductors, e.g. H05VVUSSSSCCAddressesSenor allocated to:Sensor Group 1 (front luminaires)Sensor Group 2 (rear luminaires)Sensor Group 3 (whiteboard luminaire)“Sensor” Group 4 (blackout blinds and screen)Common Group 1 (corridor and upper staircase)Common Group 2 (lower staircase etc.)Listening19


Application: open space officeSpecification example:daylight-linkedcorridor and common zone,overrides possible via infra-redhand held controllerswith textile blind and meetingtable, with 6 scenes recalledvia infra-red hand heldcontroller to adapt room todifferent usesand kitchenlinked with presence andoffice lightingHow it works:fluorescent luminaires withinthe open space are SensaLinkluminaires containing a built-inMiniSensaLink head (MenloSoftSR HFL). The other half arestandard dimmable luminaires(MenloSoft SR HFD), connectedto the DSI output of theSensaLink ones. Within thesemaster-slave installations, oneMiniSensaLink head can controla maximum of 4 DSI ballastsin total.connected to the SensaLinkBus; the slave luminaires areconnected to the masters viaa Mains/DSI lead.numbers are used to groupthe luminaires above differentdesk areas.arrangements can also befound in the manager’s office,grouped into two separategroups as this room is usedby the manager in two ways,either when working at thedesk, or when holding ameeting in the other half ofthe room.opening the textile blind infront of the manager’s office’swindow is controlled via theswitched output of a SensaLinkTransceiver, that is addressedwith an own Sensor Groupnumber: Within the scenes theblind is either closed (idealwhen sun shines directly intothe room) or opened.room, for the copy machineand the kitchen, are lit bydownlights (Cruz HFD), theseare connected to remoteSensaLink sensor heads.SensaLink luminaire.Common Sensor Group, thatlistens to all other (standard)Sensor Groups within the sameBus district: As long as one ofthe desks, or the manager’soffice, or the kitchen isoccupied, the lobby lightMainsSensaLink BusMains+ BusSSSSSMains+ DSISMSC C CSSSSCCSSCC20


whole area is unoccupied.corridor between the desksand leading to the otherareas, is commissioned as aCommon Sensor Group aswell, and holds the light untilall SensaLink luminaires andsensor heads within the wholearea are reporting vacancy.presence and daylight-linked.from scene 1 is recalled in themanager’s office, is the room’sdaylight-link deactivated.hand held controllers to setscenes or to brighten and dimthe light, one is on her/hisdesk, the other on themeeting table.receptionist have infra-red handheld controllers reachable.To dim or brighten the light,they aim the controllers to oneof the built-in MiniSensaLinkheads. The controllers show 2pairs of dim buttons, one is foroverriding the light output ofall luminaires connected to thetargeted sensor head, the otherpair is for overriding the wholeSensor Group or CommonGroup, the sensor head ispart of.connected to the SensaLinkBus, that is powered by theSensaLink Bus Power supply.SensaLink Bus wire is partlyinstalled as ring and partlyas spur.DevicesAddressesRecessed luminaire (e.g. MenloSoft SR HFD)Sensor allocated to:SRecessed luminaire with built-in MiniSensaLinkhead (e.g. MenloSoft SR HFL)SSSSSSensor Group 1 to 5 (SensaLink luminaires in openspace, above desks)SSuspended luminaire (e.g. Sienna HFD)Suspended luminaire with built-in MiniSensaLinkhead (e.g. Sienna HFL)CCommon Sensor Group 1(SensaLink luminaires inopen space, above notional corridors andcommon area)MRecessed downlights (e.g. Cruz HFD)Blind motor 230V ACRemote Sensor Head recessed mountedS SSSensor Groups 6 and 7 (SensaLink luminaires inmanager’s office)“Sensor” Group 8 (textile blind in manager’s office)Infrared hand held controllerSSensor Group 9 (remote SensaLink head inseparate room/kitchen)Transceiver (used as Motor output)SSensor Group 10 (SensaLink luminaire in lobby,above desk)Bus power supplyCCommon Group 2 (remote SensaLink head in lobby)SensaLink Bus wire**Mains wire*ListeningSensaLink Bus**+Mains wire*DSI wire*DSI+Mains wire**Standard mains wiring 1.5mm 2 with solidor stranded conductors, e.g. H05VV-U**Mains rated wiring 1.5mm 2 , twisted pair,with solid or stranded conductors, e.g. H05VV-U21


Detailed overview on all products and accessories96102982 SENSALINK MRE SENLDDSIPassive Infra-red (PIR) detector and photocell, responds to presence/absence and to light by dimming orswitching off. They can control HFD luminaires incorporating up to 8 DSI ballasts, and can be used inceiling (max. height 3m, max. thickness 54mm, hole diameter 50mm, ceiling void 125mm). Detection zoneradius 6m at 2.4m ceiling height. DSI lead 2-wire digital polarity-free, max. length 12m. SensaLink Busunscreened twisted pair 1.5mm², polarity-conscious. Photocell; adjusted when commissioned, regulationdeactivated when one of the Scenes 2 to 6 is recalled. Degree of protection IP40. Dimensions Ø 65mm,230VAC.96013500 SENSALINK MSF SENLDDSIPassive Infra-red (PIR) detector and photocell, responds to presence/absence and to light by dimming orswitching off. Can control luminaires incorporating up to 8 DSI ballasts, and can be used in conjunctionDetection zone radius 6m at 2.4m ceiling height. DSI 2-wire digital polarity-free, max. length 12m.SensaLink Bus unscreened twisted pair 1.5mm², polarity-conscious. Photocell; adjusted when commissioned,regulation deactivated when one of the Scenes 2 to 6 is recalled. Degree of protection IP53. DimensionsLuminaires with built-in MiniSensaLink headTo see which standard Thorn luminaires are SensaLink enabled,Guides. If you cannot find one within your selected luminaire range,please contact your sales office.96100101 SENSALINK MRE SENLDSWPassive Infra-red (PIR) detector and photocell, responds to presence/absence and to light by switchingluminaires on and off. Switched live output to operate standard luminaires with magnetic or fixed output HFcircuits, for a maximum load of 6A, considering inrush currents, can be used in conjunction with anceiling (max. height 3m, max. thickness 54mm, hole diameter 50mm, ceiling void 125mm). Detectionzone radius 6m at 2.4m ceiling height. SensaLink Bus unscreened twisted pair 1.5mm², polarity-conscious.Photocell: adjusted when commissioned, switching regulation deactivated when one of the Scenes 2 to 6 isrecalled. Degree of protection IP40. Dimensions Ø 65mm, height 115mm, weight 0.07kg excluding lead.22


96102983 SENSALINK SENLPProgrammer used to commission a SensaLink system. The programmable parameters of the various products(e.g. illuminance level, time delay to switch off, start-up level, fading, operation mode (auto or semi-auto),addresses and many more) can be configured via this battery-powered, hand held, infra-red unit. Theprogrammer allows commissioning and re-commissioning to be carried out with virtually no disturbance tothe building’s occupants, as programming is done remotely and therefore can be operated from the ground.Settings are chosen from the menu and transferred instantaneously to the product being programmed bypressing the Upload button. The commissioning engineer receives positive feedback at all stages of theprocess. Settings from one product can be copied in seconds to another and settings can be checked at anytime using the download function. Display 128 x 64 monochrome LCD display. Supply voltage 3 alkalinebatteries, type AAA. Dimensions 150x 85x35mm, weight approx. 0.23kg.96232304 SENSALINK SENLPS LTBus Power Supply unit provides the signalling highway for up to 100 SensaLink devices. Bus interconnectioncable 1 to 1.5mm², unscreened twisted pair, installed either as radial or ring (may be run with mainscabling): For radial Bus topology, maximum length of each radial is 500m (300m) with 1.5mm 2 (1.0mm 2 )conductor size. For ring Bus topology, maximum length of ring is 1500m (800m) with 1.5mm 2 (1.0mm 2 )conductor size. A centre-off retractive switch can be additionally connected to the ‘Wall Switch’ Commonand Up/Down terminals: This enables to dim, brighten and to switch on and off all SensaLink devicesallocated to Sensor Group 1 and 2 within the supplied bus district. Dimensions: 125x175x75mm, weight:0.12kg. Mounted in ceiling or on wall.96232305 SENSALINK SENLPS GBus Power Supply provides the signalling highway for up to 200 SensaLink devices. Bus interconnectioncable 1 to 1.5mm², unscreened twisted pair, installed either as radial or ring (may be run with mainscabling): For radial Bus topology, maximum length of each radial is 500m (300m) with 1.5mm 2 (1.0mm 2 )conductor size. For ring Bus topology, maximum length of ring is 1500m (800m) with 1.5mm 2 (1.0mm 2 )conductor size. In larger applications with more than 200 SensaLink devices, up to 99 of these Buspower supplies can be linked to a common spine or backbone (2x2x0.2mm 2 , twisted pair, screenedcommunication cable, e.g. a RS-232 computer cable, maximum length 1200m). With the spine theCommon Sensor Group 1 becomes a Building Group, providing building wide linking of all CommonGroups 1 within the different Bus districts. Three pairs of switch input terminals enable central control: Withopen switch connected to ‘Load Shed 1’ or ‘Load Shed 2’ all SensaLink devices allocated to Global Groupflash when several of these Bus Power Supplies are connected together and Building Group (CommonSensor Group 1) linking occurs. Supply voltage 230VAC. Dimensions 213x185x117mm. Degree ofprotection IP65. Mounted adjacent to the mains distribution board for the area being controlled.23


96102981 SENSALINK SENLRCInfra-red hand held Controller provides user with local override facility, allows to select preferred light levelstargeted to a SensaLink luminaire or multi sensor head. The controller shows 2 pairs of dim buttons, one isfor overriding the light output of all luminaires connected to the targeted sensor head, the other pair is foroverriding the whole Sensor Group or Common Group, the sensor head is part of. Additionally it enables toset and recall six scenes for the different activities in a room via 6 small buttons. Supply voltage 2 alkaline96237037 SENSALINK SENLSS V2Six scenes can be recalled by depressing the appropriate button “1” to “6” on the Scene Select Plate,individually using the SensaLink Infra-red hand held Controller, and then one of the scene buttons is pressedand held until the luminaires flash to confirm the setting. Additionally the scene plate provides buttons withfor SensaLink Bus unscreened twisted pair 1.5mm², polarity-conscious. IR port for interfacing with SensaLinkdouble back box (not supplied) for sinking in (min. box depth 30mm) or dry-line plasterboard walls. Supplyvoltage 230VAC.96237037 plus 96237039Cover plate (size 85 x 145mm) ordered separately:96237038 SENSALINK SENLSS V2 BR POL COVERMetal cover polished brass finish for SensaLink Scene Select Plate Version 296237039 SENSALINK SENLSS V2 CHR POL COVERMetal cover polished chrome finish for SensaLink Scene Select Plate Version 296237040 SENSALINK SENLSS V2 RS BS COVERMetal cover brushed stainless steel finish for SensaLink Scene Select Plate Version 296237041 SENSALINK SENLSS V2 WHI COVERMetal cover white finish for SensaLink Scene Select Plate Version 296218671 SENSALINK WHI MWA SENLCPluminaires. Can be allocated to one Sensor Group number via ‘dip’ switches. Supplied via SensaLink Bus(consumes 2 bus loads). Connection for SensaLink Bus unscreened twisted pair 1.5mm², polarity-conscious.30mm) or dry-line plasterboard walls.96013499 SENSALINK SENLTSensaLink Universal Bus Transceiver provides a DSI output for controlling dimmable luminaires incorporatingup to 20 DSI ballasts, a switching relay output (maximum load 10A) for switching fixed output luminaires(with magnetic or electronic gears) and non-lighting loads, e.g. screens and blackout blind motors.Additionally features inputs for external devices, e.g. external switches, timers, BMS outputs. Is also usedfor room partitions, enabling individual control within two rooms when a partition is closed, and joinedcontrol of the combined rooms when the partition is opened. Supply voltage 230VAC.Dimensions 175x125x75mm, weight 0.12kg. Mounted in ceiling or on wall.24


22154307 PDAX 500VAPhase dimmer/Reverse phase dimmer (automatic load detection), controllable via any DSI output, forcontinuous dimming of ohmic light sources, LV halogen lamps with magnetic or electronic transformers.A total connected load of 40 to 500VA can be operated. Dimming range 1...100%. Connection via screwterminals, housing made of flame-resistant polycarbonate – halogen-free, suited for luminaire installation orceiling recess, admissible ambient temperature of 0...60°C (max. 300VA)/0...45°C (max. 500VA).Degree of protection IP20. Size 167x42x31mm. Weight 200g.22154306 PDAS 1000VAPhase dimmer/Reverse phase dimmer (automatic load detection), controllable via any DSI output forcontinuous dimming of ohmic light sources, LV halogen lamps with magnetic or electronic transformers. Atotal connected load of 40 to 1000VA can be operated. Dimming range 1...100%. Connection via screwterminals, housing made of flame-resistant polycarbonate - halogen-free, suitable for installation in switch ordistribution cabinets on 35mm DIN rail. Permitted ambient temperature 0...40°C. Degree of protection IP20.Width 105mm (6 units), height 90mm, depth 59mm. Weight 400g.86457873 TE one4all sc 105VADigital, dimmable transformer with DSI/DALI interface; controllable via any DSI or DALI output, dimmingrange of 1%…100%; for operation of 12V low voltage tungsten-halogen lamps with a lamp power ofbetween 20 and 105VA; lamp leads up to 2m; housing made of flame-resistant polycarbonate, halogenfree;suitable for luminaire installation; protection class II; ambient temperature –25…+60°C. Size167x42x31mm. Weight 180g.86457874 TE one4all sc 150VADigital, dimmable transformer with DSI/DALI interface; controllable via any DSI or DALI output, dimmingrange of 1%…100%; for operation of 12V low voltage tungsten-halogen lamps with a lamp power ofbetween 20 and 150VA; lamp leads up to 2m; housing made of flame-resistant polycarbonate,halogen-free; suitable for luminaire installation; protection class II; ambient temperature –20…+50°C.Size 207x46x40mm. Weight 290g.25


Ordering GuideDescriptionSAP codeDescriptionSAP codeMultisensor head with DSI output recessed mountedScene Select Plate and Covers 96102982Multisensor head with DSI output surface mounted 96013500Multisensor head with switched output recessed mounted 96100101Programmer 96102983Bus Power Supplies, global and lite 96232305 96232304Infrared Hand held Controller 96102981 96237037 96237038 96237039 96237040 96237041Local Control Plate including cover 96218671Universal Transceiver 96013499Accessories / DSI/DALI transformer, 12V, 20-105VA and 50-150VA 86457873 86457874Accessories / DSI phase or reverse phase dimmer, auto load detection,40-500VA and 40-1000VAPDAX 500VA 22154307PDAS 1000VA 22154306Energy efficiencyAnnual Energy Costs- Application exampleClassroomswhen you consider the numberof rooms within a building andthe difference between old andnew lighting technologies. Asan example: The comparisonbetween 1970’s classroomsand those of today (with andwithout daylight-linking) clearlyshows significant cost savings areavailable. The example is basedon a typical 1970 classroomlighting installation of nine fittingseach with 2x40W T38 lamps andmagnetic gear, compared to atypical 2009 classroom of ninefittings each with 1x35W T16lamp and electronic gear, andfinally the same modern classroomwith the dimmable versions ofthe same luminaires linked to theincoming daylight using SensaLink(maintenance based on 16000hours, 2480 hours use per annumwith varying lighting durationsbased on time of day).Cost of Energy (£/year)300000250000200000150000100000500000Classroom Annual Energy Costs (9p/kWh)0 3 6 9 12 15 18 21 24Number of classroomsKey9 luminaires,2x40W T38,magnetic gear9 luminaires,1x35W T16,electronic gear9 luminaires,1x35W T16,dimmableelectronic gear,linked toincoming daylight26


Lighting people and placesThorn Lighting LimitedUKSilver Screens, Elstree Way, Borehamwood,Hertfordshire, WD6 1FEUK Sales desk -Orders/Stock EnquiriesTel: 0844 855 4810Fax: 0844 855 4811IrelandThorn Lighting (Ireland) LimitedCentury HouseHarolds Cross RoadDublin 6WTel: (353) 1 4922 877Fax: (353) 1 4922 724E-mail: dublinsales@thornlighting.comThorn Olympics Sports Lighting TeamTel: 07785 251 438E-mail: olympics.team@thornlighting.comSpare PartsTel: 0191 301 3131Fax: 0191 301 3038E-mail: spares@thornlighting.comTechnical SupportTel: 0844 855 4812Fax: 020 8732 9882E-mail: technical@thornlighting.comBrochureline Answering ServiceBrochures on specific products/rangesTel: 020 8732 9898Fax: 020 8732 9899E-mail: brochures.uk@thornlighting.comwww.thornlighting.co.ukThorn Lighting is constantly developing and improving its products. All descriptions, illustrations,drawings and specifications in this publication present only general particulars and shall not formpart of any contract. The right is reserved to change specifications without prior notification orpublic announcement. All goods supplied by the company are supplied subject to the company’sGeneral Conditions of Sale, a copy of which is available on request. All measurements are inmillimetres and weights in kilograms unless otherwise stated.Publication No: 428 (GB) Publication Date: 09/09Member of The LightingIndustry FederationISO 9001:2000Reg: 2916/0Manufacturing & Distribution

More magazines by this user
Similar magazines