LumeLEX 2024 SERIES INSTALLATION INSTRUCTIONS THIS ...

More documents

Recommendations

Info

InstallingorRemovingtheReflectorThe LumeLEX 2000 family ships with the reflectorpackaged separately.Before Installing the Fixture: The reflector isattached using a 3-tab bayonet system. To installthe reflector, insert the tabs into the notches onthe LED Adapter Ring and rotate clockwise.STEP ACTION1 Insert the new reflector by lining upthe three tabs with the notches in theLED Adapter Ring, and rotatingclockwise until it is secured in place(Fig. 1).2 Remove the reflector by turning itcounter-clockwise, then pulling it outof the fixture (Fig. 2).Figure 1. The three notches in the LED AdapterRing. Align the reflector tabs with thesenotches and rotate clockwise to secure it inplace.Figure 2. Rotate reflector counter-clockwise toremove it.www.LightingServicesInc.com Page 2 of 6 IS-0103_D
Installingthe Fixturewith the-00 Fittingon an LSITrack or a-BUSfitting onan LSIBuswayFOR USE WITH LSI 3, 4, 5, 6, 8, AND 9 SERIES TRACKAND LSI 20 SERIES BUSWAY SYSTEMS ONLY.INSTALLATION INSTRUCTIONS: The track or buswaymust already be installed according to code requirements.When installing or using this track or busway system, basicsafety precautions should always be followed, including thefollowing:• Read all instructions.• Do not install any part of a track or busway system lessthan 5 feet above the floor (8 feet for 277V).• Do not install any fixture closer than 6 inches from anycurtain or similar combustible material.STEP ACTION1 Flip the fitting switch off and open the fitting handle(Fig. 3).2 Are you using a one-circuit or two-circuit system?• If one-circuit, make sure the brass contacts thatprotrude from the side of the fitting face the copperbusbars inside the track or busway.• If two-circuit, inserting the fitting in one directionconnects to circuit one. Removing and reversingthe direction of the fitting connects to circuit two.3 Insert the fitting straight up into the track or buswayuntil fully seated (Fig. 4).4 Close the handle and flip the fitting switch on (Fig 5).WARNING: Do not look directly at lit LED.5 To remove the fitting, hold the fixture in place, flipthe fitting switch off, open the handle, and pull thefitting straight off the track or busway.Figure 3. Fitting with switch OFFand handle OPEN.Figure 4. Inserted fittingFigure 5. Switch ON, fitting handleclosedInstallingthe Fixturewith a 5ACanopyBefore Installing: Consult the code requirements for fixturemounting. Mount the fixture to a ceiling constructed of noncombustiblematerial, away from any flammable materials.STEPACTION1 Turn off all power to the fixture mount.2 Unscrew the 2 supplied canopy mounting screws,and remove the crossbar from the canopy (Fig. 6).3 Attach the canopy crossbar (Fig. 7) to a ceilingjunction box with 2 screws (supplied by others).4 Fasten the power wires (Fig. 7) from the junctionbox to the fixture wires.Note: Connect green to ground, black to the circuitline, and white to neutral.5 Attach the canopy to the ceiling with the 2 suppliedcanopy mounting screws.Figure 6. Fixture mounted on the5A CanopyFigure 7. Ground and power wireswith canopy crossbarwww.LightingServicesInc.com Page 3 of 6 IS-0103_D
Page 1: LumeLEX 2024 SERIES INSTALLATION IN
Page 5 and 6: Aiming theSelf-LockingandWrench-Loc

LumeLEX 2024 SERIES INSTALLATION INSTRUCTIONS THIS ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?