plough wearing parts

MØLBRO WEARING PARTS SPECIAL CHARACTERISTICS16.02.2009MOULDBOARD- homogenous hardness though the whole cross section -extreme durability the whole lifetime of mouldboardWING/LEAF- thanks to strong edged front edge and thin blade,the plough part is extremely durable- elastic material around the hole - a very high resistanceto crancks and breakagesMouldboardextensionTrashboardMouldboardShinShare knifeSubsoiler bladeLandsideWing/leafPointAll landsides are equippedwith two holes which enablesmounting of the following parts:NORMAL POINT- same top quality as other partsEUROPOINT POINT- the back of the Europoints are coated with a very hard layer of carbide- ensures that the Europoint is self sharpening in use- the carbide coating also ensures that the Europoint is wearing very slowlySUBSOILER BLADE- lifts the top soil right under the heel of the plough and helps to stopthe formation of a pan and assists with promoting sound soil conditions- can be mounted on last or all Mølbro landsidesSWORD COULTER- cuts through the furrow wall to enable the use of wide tractor tyres thuspreventing damage to the tyre/rim- mounting to last landsideWEARING PLATE- prolongs the life of the landside by 3 to 4 times- two models - low and highT7.02Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FOR FISKARS, KHN, KH, L, P and PP PLOUGHS91100126KHNKHL, P and PPORDER NO. BOLT BAG MODEL DESCRIPTIONA95002491M L Mouldboard, plastic, incl. shinA950025-05 AB121 Shin RA950025-61 AB119 Wing 14” RA950024-89 AB119 Wing 16” RA950024-90 AB119 Point RA950041-18 AB119 Point LA950037-32 AB122 Landside front RA950037-36 AB129 Landside rear RORDER NO. BOLT BAG MODEL DESCRIPTIONA950006-83 AB119 Wing 14” RA950006-84 AB119 M Wing 16” RA91100143 AB121 L Reinforced ploughshare 16” RA91100091MA950006-75 AB119 Point RR = right, L = leftIf the order number starts with A, the product is in stock programMouldboard, plasticA950011-72 AB132 Landside short RA950011-71 AB132 Landside long RA63600A AB094 M Wearing plate RA63601A AB094 M Wearing plate LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LORDER NO. BOLT BAG MODEL DESCRIPTIONA91100126 AB121 Wing 13” RA91100129 AB121 M Wing 16” R- suitable also for 14” ploughsM = Mølbro designed special modelL = Long Life modelT7.03Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FOR AGROLUX FK and FC PLOUGHSFKFCORDER NO. BOLT BAG MODEL DESCRIPTIONA96064 AB167 Turbo-trashboard R (83969)A96064MR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelTurbo-trashboard, plastic RA96065 AB167 Turbo-trashboard L (83968)A96065MA84022Turbo-trashboard, plastic LFittings for trashboard RA85239 AB063 Mouldboard RA85261M L Mouldboard plastic, inc. shin RA85262M L Mouldboard plastic, inc. shin LA74922 AB082 M Mouldboard extension RA80559 AB082 M Mouldboard extension LA83980 AB065 Shin RA84083 AB065 Shin LA85383 AB052 Wing 14” RA85381 AB052 Wing 14” LA85384 AB052 Wing 16” RA85382 AB052 Wing 16” LA84942 AB031 Wing RA85204 AB031 Point LA94622 AB084 Share knife RA94623 AB084 Share knife LA85675 AB073 Landside short RA86126 AB073 Landside short LA85799 AB073 Landside long RA86136 AB073 Landside long LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter R (95678)A1349409 AB052 M Sword coulter L (95679)A800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LORDER NO. BOLT BAG MODEL DESCRIPTIONA96064 AB167 M Turbo-trashboard R (83969)A96064M L Turbo-trashboard, plastic RA96065 AB167 M Turbo-trashboard L (83968)A96065M L Turbo-trashboard, plastic LA84022Fittings for trashboard RA84031 AB062 Mouldboard RA84033 AB065 Shin RA85004 AB052 Wing 14” RA85194 AB052 Wing 14” LA85039 AB052 Wing 16” RA84987 AB031 Wing RWing LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter R (95678)A1349409 AB052 M Sword coulter L (95679)A800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LT7.04Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.200994606946079460494605PARTS FORAGROLUX AXPLOUGHORDER NO. BOLT BAG MODEL DESCRIPTIONA74922 AB082 M Mouldboard extension RA80559 AB082 M Mouldboard extension LA96064 AB167 M Turbo-trashboard RA96064M L Turbo-trashboard, plastic RA96065 AB167 M Turbo-trashboard LA96065M L Turbo-trashboard, plastic LA94594 AB056 Mouldboard RA94594M L Mouldboard, plastic, inc. shin RA94595 AB066 Mouldboard LA94595M L Mouldboard, plastic, inc. shin LA94596 AB052 Shin RA94597 AB052 Shin LA94598 AB052 Wing 14” RA94599 AB052 Wing 14” LA94600 AB052 Wing 16” RA94601 AB052 Wing 16” LA94602 AB052 Wing 18” RA94603 AB052 Wing 18” LA94610 AB031 Reversible point RA94611 AB031 Reversible point LA94606 AB074 Landside short RA94607 AB074 Landside short LA94604 AB074 Landside long RA94605 AB074 Landside long LA94622 AB084 Share knife RA94623 AB084 Share knife LA94624 AB082 Fittings for trashboard RA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.05Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.200995000-83795000-474PARTS FORAGROLUX(/FISKARS)PLOUGHSORDER NUMBER BOLT BAG MODEL DESCRIPTIONA80645 AB003 Skim mouldboard RA80644 AB050 Skim share RA91802 AB052 Skim share LA72547A80662Disc coulter 18” R&LDisc coulter 20” R&LA80967AHKSRepair kit for disc coulter hub,inc. bearings, seals and boltsA95000-474 Disc coulter 20” R&L, KH, KHNA95000-837 Disc coulter 18” R&L, KH, KHNREPAIR KIT FOR DISC COULTER HUB KHNOAS305510Shaft gasket 30x55x10, 1 pcL6205-2RSBearings 25x52x15, 2 pcsLRU25Lock ring ext. 25 mm, 1 pcREPAIR KIT FOR DISC COULTER HUB KHOAS35527Shaft gaskets 35x52x7, 2 pcsA80967AH (4-bolts)Disc coulter hub M30 RA80967AV (4-bolts)Disc coulter hub M30 LA80966Cover R&LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.06Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORKVERNELANDPLOUGHS53-SERIE(1965-1974)ORDER NUMBER BOLT BAG MODEL DESCRIPTIONA73091 AB095 Share knife under the point RA53090 AB094 Reversible point RA5309MOLC * AB094 M Europoint point carbide coated RA53085 AB099 M Share f/reversible point 12” RA53087 AB100 M Share f/reversible point 14” RA53088 AB100 M Share f/reversible point 16” RA53684 AB118 Landside short RA53683 AB118 Landside long RA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA800MOL AB096 Subsoiler blade RR = right, L = leftIf the order number starts with A, the product is in stock program* triple service life compared to normal pointM = Mølbro designed special modelL = Long Life modelT7.07Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORKVERNELANDPLOUGHSNBR 3(1975-1982)ORDER NBR BOLT BAG MODEL DESCRIPTIONA73/63-300 AB167 M Turbo-trashboard RA73/63-300M AB167 L Trashboard, plastic RA73/63-301 AB167 M Turbo-trashboard LA73/63-301M AB167 L Trashboard, plastic LA73/63-310 AB167 Fittings for trashboard RA73/63-311 AB167 Fittings for trashboard LA53387 AB082 M Mouldboard extension RA63388 AB082 M Mouldboard extension LA63283 AB056 Mouldboard RA63283M L Mouldboard, plastic RA63293 AB056 Mouldboard LA63240 AB053 Shin RA63250 AB053 Shin LA63013 AB100 M EUROSHARE 12” RA63014 AB100 M EUROSHARE 14” RA63017 AB100 M EUROSHARE 14” LA63015 AB100 M EUROSHARE 16” RA63018 AB100 M EUROSHARE 16” LA73091 AB095 Share knife under the point RA73092 AB095 Share knife under the point LA53090 AB094 Reversible point RA63090 AB094 Reversible point LA5309MOLC * AB094 M Europoint point carbide RA6309MOLC * AB094 M Europoint point carbide LA63610 AB128 Landside short R&LA63611 AB128 Landside long R&LA63615 AB103 Landside short, low RA63606 AB103 Landside short, low LA63613 AB103 Landside long, low RA63604 AB103 Landside long, low LA63602 AB118 Landside short RA63601 AB118 Landside long RA63605 AB103 Landside short, low RA63607 AB136 Conversion plate RA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life model* triple service life compared to normal pointT7.08Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORKVERNELANDPLOUGHSNBR 6, 7, 8, 9(1983-)ORDER NUMBER BOLT BAG MODEL DESCRIPTIONA73/63-300 AB167 M Turbo-trashboard RA73/63-300M AB167 L Turbo-trashboard, plastic RA73/63-301 AB167 M Turbo-trashboard LA73/63-301M AB167 L Turbo-trashboard, plastic LA73/63-310 AB167 Fittings for trashboard RA73/63-311 AB167 Fittings for trashboard LA73803 AB156 M Brace R&LA73800 AB045 Brace fitting RA73801 AB082 Brace fitting LA53387 AB082 Mouldboard extension RA63388 AB082 Mouldboard extension LA73290 AB059 Mouldboard RA73291 AB059 Mouldboard LA73286 AB056 Mouldboard RA73286M L Mouldboard, plastic, incl. shin RA73287 AB056 Mouldboard LA73287M L Mouldboard, plastic, incl. shin LA73256 AB058 Shin RA73257 AB058 Shin LA73250 AB052 Shin RA73251 AB052 Shin LA73266 AB052 Bracket for shin RA73406 M Frog RA73002 AB113 M EUROSHARE 14” RA73003 AB094 M EUROSHARE 14” LA73004 AB113 M EUROSHARE 16” RA73005 AB113 M EUROSHARE 16” LA73006 M EUROSHARE 18” RA73091 AB095 Share knife under the point RA73092 AB095 Share knife under the point LA53090 AB094 Reversible point RA63090 AB094 Reversible point LA5309MOLC * AB094 M Europoint point carbide RA6309MOLC * AB094 M Europoint point carbide LA73608 AB111 M Landside short R&LA73609 AB111 M Landside long R&LA73088 AB110 Share knife RA73089 AB110 Share knife LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life model* triple service life compared to normal pointT7.09Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.12.2009PARTS FORKVERNELANDPLOUGHSNBR 19ORDER NBR BOLT BAG MODEL DESCRIPTIONA73/63-300 AB167 M Turbo-trashboard RA73/63-300M AB167 L Turbo-trashboard, plastic RA73/63-301 AB167 M Turbo-trashboard LA73/63-301M AB167 L Turbo-trashboard, plastic LA73/63-310 AB167 Fitting for trashboard RA73/63-311 AB167 Fitting for trashboard LA53387 AB082 M Mouldboard extension RA63388 AB082 M Mouldboard extension LA73290 AB059 Mouldboard RA73291 AB059 Mouldboard LA73800 AB045 Brace fitting RA73801 AB082 Brace fitting LA73230 AB058 Shin RA73231 AB058 Shin LA73266 AB052 Bracket for shin RA73054 AB113 M EUROSHARE 14” RA73055 AB113 M EUROSHARE 14” LA73056 AB113 M EUROSHARE 16” RA73091 AB095 Share knife under the point RA73092 AB095 Share knife under the point LA53090 AB094 Reversible point RA63090 AB094 Reversible point LA5309MOLC * AB094 M Europoint point carbide RA6309MOLC * AB094 M Europoint point carbide LA73608 AB111 Landside short R&LA73609 AB111 Landside long R&LA73088 AB110 Share knife RA73089 AB110 Share knife LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life model* triple service life compared to normal pointT7.10Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS09.10.2009PARTS FORKVERNELANDPLOUGHSNBR 20NMB 14:Ploughs which are originally withwhite plastic mouldboard.Other parts the same as inploughs nbr 20,except trashboard and bracketsORDER NUMBER BOLT BAG MODEL DESCRIPTIONA73/63-300 AB167 M Turbo-trashboard RA73/63-300M AB167 L Turbo-trashboard, plastic RA73/63-301 AB167 M Turbo-trashboard LA73/63-301M AB167 L Turbo-trashboard, plastic LA73/63-310 AB167 Fitting for trashboard RA73/63-311 AB167 Fitting for trashboard LA73054 AB113 M EUROSHARE 14” RA73055 AB113 M EUROSHARE 14” LA73056 AB113 M EUROSHARE 16” RA73091 AB095 Share knife under the point RA73092 AB095 Share knife under the point LA53090 AB094 Reversible point RA63090 AB094 Reversible point LA5309MOLC * AB094 M Europoint point carbide RA6309MOLC * AB094 M Europoint point carbide LA73608 AB111 Landside short R&LA73609 AB111 Landside long R&LA73088 AB110 Share knife RA73089 AB110 Share knife LA63600A AB094 Wearing plate RA63601A AB094 Wearing plate LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life model* triple service life compared to normal pointT7.11Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORKVERNELANDPLOUGHSORDER NBR BOLT BAG MODEL DESCRIPTIONA66880 AB026 Skim mouldboard RA66881 AB026 Skim mouldboard LA56873 AB004 Skim share, short RA66868/66869 AB004 Skim share, long R&LA56112Disc coulter 18” R&LA56156Cover R&LA60609Disc coulter hub 34 mm R&LA60624Disc coulter hub 30 mm R&LA60609KSRepair kit for disc coulter hub,incl. bearings, seals, boltsand lock ringA73411 M Frog R **A73412 M Frog L **R = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life model** suitable for ploughs nbr 6, 7, 8 and 9T7.12Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS16.02.2009ABCDEFKVERNELANDLEAFSPRINGSORDER NUMBER BOLT BAG DESCRIPTION MODEL POSITION REF.A57063 Main blade 1 AA57064 Blade nbr 1 2 and 3 BA57065 Blade nbr 2 4 CA57066 Blade nbr 3 5 DA57067 Blade nbr 4 6 and 9 EA57068 Blade nbr 5 7 and 8 FPK12050 Screw M12x50 GPK12035 Screw M12x35 HPML12000PAL12000A60703Nut M12 nylocWasher M12Complete package- incl. 1xA, 2xB, 1xC, 1xD,2xE and 2xF assembledR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.13Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FOR ÖVERUM UC (1984-) AND SR PLOUGHSUCORDER NBR BOLT BAG MODEL DESCRIPTIONA96064 AB167 M Turbo-trashboard R (83969)A96064M L Trashboard, plastic RA96065 AB167 M Turbo-trashboard L (83968)A96065M L Trashboard, plastic LA84022 M Fitting for trashboard RA84031 AB062 Mouldboard RA84033 AB065 Shin RA74922 AB082 Mouldboard extension RSRA80559 AB082 Mouldboard extension LA85004 AB052 Wing 14” RA85194 AB052 Wing 14” LA85039 AB052 Wing 16” RA84958 AB054 Support RA83981 AB074 Landside short RA85196 AB074 Landside short LA85118 AB074 Landside long RA85197 AB074 Landside long LA94622 AB084 Share knife RA94623 AB084 Share knife LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LORDER NBR BOLT BAG MODEL DESCRIPTIONA80625 AB120 M Trashboard RA80604 AB060 Mouldboard R (-74-79)A80604M L Mouldboard, plastic, incl. shin RA74922 AB082 M Mouldboard extension RA80609 AB139 Shin R (-74-79)A74606 AB119 Wing 14” R (-74-79)A74607 AB119 Wing 16” R (-74-79)A80605-92 AB050 Wing 14” R (-80-83)A80605-93 AB050 Wing 16” R (-80-83)A74601 Point, steel casting R (-74-79)A76601 M Point, weld-on RA80601 AB051 Wearing plate, rev. RA84239 AB138 Landside short R (-80-83)A80603 AB138 Landside long R (-80-83)A74612 AB122 Wearing plate R (-74-79)A74602 AB130 Landside short R (-74-79)A74603 AB130 Landside long R (-74-79)A63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA800MOL AB096 M Subsoiler blade RR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.14Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORÖVERUM VPLOUGHS1984-ORDER NBR BOLT BAG MODEL DESCRIPTIONA96064 AB167 Turbo-trashboard R (83969)A96064MTurbo-trashboard, plastic RA96065 AB167 Turbo-trashboard L (83968)A96065MTurbo-trashboard, plastic LA84022Fitting for trashboard RA84031 AB062 Mouldboard RA84033 AB065 Shin RA74922 AB082 Mouldboard extension RA80559 AB082 Mouldboard extension LA85261 AB064 Mouldboard RA85261MMouldboard, plastic, incl. shin RA85262 AB064 Mouldboard LA85262MMouldboard, plastic, incl. shin LA83980 AB065 Shin RA84083 AB065 Shin LA84060 AB086 Reversible point RA85143 AB086 Reversible point LA84288 AB055 Support RA84289 AB055 Support LA85383 AB052 Wing 14” RA85381 AB052 Wing 14” LA85384 AB052 Wing 16” RA85382 AB052 Wing 16” LA83981 AB074 Landside short RA85196 AB074 Landside short LA85118 AB074 Landside long RA85197 AB074 Landside long LA94622 AB084 Share knife RA94623 AB084 Share knife LA63600A AB094 Wearing plate R&LA63601A AB094 Wearing plate R&LA1349408 AB052 Sword coulter RA1349409 AB052 Sword coulter LA800MOL AB096 Subsoiler blade RA801MOL AB096 Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.15Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.200994606946079460494605PARTS FORÖVERUM XLPLOUGHSXL 1991-ORDER NBR BOLT BAG MODEL DESCRIPTIONA96064 AB167 M Turbo-trashboard RA96064M L Turbo-trashboard, plastic RA96065 AB167 M Turbo-trashboard LA96065M L Turbo-trashboard, plastic LA94624 AB082 M Fitting for trashboard RA74922 AB082 Mouldboard extension RA80559 AB082 Mouldboard extension LA94594 AB056 Mouldboard RA94594M L Mouldboard, plastic, inc. shin RA94595 AB066 Mouldboard LA94595M L Mouldboard, plastic, inc. shin LA94596 AB052 Shin RA94597 AB052 Shin LA94608 AB086 Reversible point RA94609 AB086 Reversible point LA94612 AB069 Support RA94613 AB069 Support LA94598 AB052 Wing 14” RA94599 AB052 Wing 14” LA94600 AB052 Wing 16” RA94601 AB052 Wing 16” LA94602 AB052 Wing 18” RA94603 AB052 Wing 18” LA94606 AB074 Landside short RA94607 AB074 Landside short LA94604 AB074 Landside long RA94605 AB074 Landside long LA94622 AB084 Share knife RA94623 AB084 Share knife LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.16Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORÖVERUM XUPLOUGHSORDER NBR BOLT BAG MODEL DESCRIPTIONA96064 AB167 M Turbo-trashboard RA96064M L Turbo-trashboard, plastic RA96065 AB167 M Turbo-trashboard LA96065M L Turbo-trashboard, plastic LA94624 AB082 M Fitting for trashboard RA74922 AB082 M Mouldboard extension RA80559 AB082 M Mouldboard extension LA94608 AB086 Reversible point RA94609 AB086 Reversible point LA94612 AB069 Support RA94613 AB069 Support LA96090 AB052 Wing 16” RA96091 AB052 Wing 16” LA96094 AB069 Landside RA94622 AB084 Share knife RA94623 AB084 Share knife LA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.17Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FORÖVERUMPLOUGHSORDER NUMBER BOLT BAG MODEL DESCRIPTIONA80645 AB003 Skim mouldboard RA80644 AB050 Skim share RA73249Cover R&LA80966Cover R&LA73242ADisc coulter hub 1 1/8” WG R&LA80967AHDisc coulter hub M30 RA80967AVDisc coulter hub M30 LA80967AHKSRepair kit for disc coulter hubincl. bearings, seals and boltsA72547Disc coulter 18” R&LA80662Disc coulter 20” R&LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.18Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.06.2009PARTS FOR KUHN-HUARD VS/N AND RH/RLM PLOUGHSVS/NRH/RLMORDER NBR BOLT BAG MODEL DESCRIPTIONA622128 AB095 Reversible point, Z-profile RA622129 AB095 Reversible point, Z-profile LA270MOL AB095 M Share knife RORDER NBR BOLT BAG MODEL DESCRIPTIONA622128 AB095 Reversible point, Z-profile RA622129 AB095 Reversible point, Z-profile LA270MOL AB095 M Share knife RR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.19Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS01.12.2009PARTS FORKUHN-HUARDH4 AND H6PLOUGHSORDER NBR BOLT BAG MODEL DESCRIPTIONA622172 AB113 M EUROSHARE 16” RA622173 AB113 M EUROSHARE 16” LA270MOL AB095 M Share knife RA622128 AB095 Reversible point, Z-profile RA622129 AB095 Reversible point, Z-profile LA223120 AB097 Skim point RA223121 AB097 Skim point LA279140 AB099 Reversible point R & L longA223122 AB099 Reversible point R & L shortA63600A AB094 M Wearing plate R&LA63601A AB094 M Wearing plate R&LA800MOL AB096 M Subsoiler blade RA801MOL AB096 M Subsoiler blade LA1349408 AB052 M Sword coulter RA1349409 AB052 M Sword coulter LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.20Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLOUGH WEARING PARTS16.02.2009A88873A801101A801102PARTS FORKYLLINGSTADPLOUGHSPARTS FOR ÖVERUMSM, SML AND SMKPLOUGHSSML 1964-1974 one-part mouldboardPARTS FOR SAMPOPLOUGHSPARTS FOR VOGELNOOT PLOUGHSORDER NBR BOLT BAG MODEL DESCRIPTIONA405127 M Share f/reversible point RA415256 AB045 Point RORDER NBR BOLT BAG MODEL DESCRIPTIONA72633 AB122 Wing 14” RA71345 AB122 Wing 16” LA76601 M Point, weld-on RA72635Point, steel casting RORDER NBR BOLT BAG MODEL DESCRIPTIONA88873 AB124 Wing 16” Rsuitable for 13” and 14” ploughs bytaking off a piece from the cornerORDER NBR BOLT BAG MODEL DESCRIPTIONA801101 AB094 Point RA801102 AB094 Point LR = right, L = leftIf the order number starts with A, the product is in stock programM = Mølbro designed special modelL = Long Life modelT7.21Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ORIGINAL WEARING PART BOLTS16.02.2009PICTURE BOLT LENGTH ORDER NUMBER1 M10 Share boltQuality 10.92 M10 Share boltQuality 10.93 M10 Share boltQuality 10.94 M12 Share boltQuality 12.95 M12 Share boltQuality 12.96 M12 Share boltQuality 10.97 M12 Share boltQuality 10.98 M12 Share boltQuality 40-43 HRC10 M12 Share boltQuality 40-43 HRC11 M14 Share boltQuality 12.925303550AP9705025AP9705030AP9705035AP970505030 AP970513025 AP97099253035455565303530354045603035453238453438AP9710030AP9710035AP9710045AP9710055AP9710065AP9710130AP9710135AP9710230AP9710235AP9710240AP9710245AP9710260AP9714730AP9714735AP9714745AP9714832AP9714838AP9714845AP9714934AP971493834 AP9719934T7.22Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ORIGINAL WEARING PART BOLTS16.02.2009PICTURE BOLT LENGTH ORDER NUMBER1 7/16” UNF Share boltDS6006 Quality 8.82 7/16” UNC Share boltQuality 12.93 5/8” UNF Share boltQuality 8.84 3/4” UNC Share boltQuality 10.95 M16 Share boltQuality 10.96 M20 Share boltQuality 10.93035AP9760030AP976003533 AP97649347090AP9775070AP977509090 AP978009050857585AP9724950AP9724985AP9730075AP9730085T7.23Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ORIGINAL WEARING PART NUTS16.02.2009PICTURE BOLT LENGTH ORDER NUMBER1 M10 NutDIN 934 Quality 8.82 M12 NutDIN 934 Quality 8.83 M14 NutDIN 934 Quality 8.84 M16 NutDIN 934 Quality 8.85 M20 NutDIN 934 Quality 8.86 M14 x 1,5 NutDIN 934 Quality 8.87 M12 Lock nutDIN 985 Quality 8.88 7/16” UNF Lock nutQuality 8.89 M14 Nut collarsQuality 10.917 PM10000 (kg)19 PM12000 (kg)22 PM14000 (kg)24 PM16000 (kg)30 PM20000 (kg)22 PMH141519 PML12000 (kg)11/16” PMFL71619 AP979041410 3/8” UNF Nut ANSI B18.29/16” PMF38Quality 8.811 7/16” UNF Nut ANSI11/16” PMF716B18.2 Quality 8.811 7/16” UNC Nut ANSI11/16” PMC716B12.2 Quality 8.812 1/2” UNF Nut ANSI B18.23/4” PMF12Quality 8.813 5/8” UNF Nut ANSI B18.215/16” PMF58Quality 8.814 3/4” UNC Nut ANSI1 1/8” PMF34B18.2 Quality 8.815 3/8” x 23 x 2,5 Washer PAL10000 (kg)16 7/16” x 26 x 2,5 Washer PAL12000 (kg)17 C12 Conical spring washerDIN 74361PJLK12000T7.24Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

CULTIVATOR PARTS01.12.2009rightleftøPOINTS35353- forged 18/9 mm- dist. between holes 40-88 mm130 mmTINESOR. NBR SIZE A HOLEø C D E FS30311 30x30 L 120 13 280 510 365 45S30312 30x30 R 120 13 280 510 365 45S30321 30x30 L 120 13 280 610 45S30322 30x30 R 120 13 280 610 45S35351 35x35 L 145 13 280 635 400 75S35352 35x35 R 145 13 280 635 400 75MOUNTING BOLTS30324- 12 x 60 mm440 mmPOINT STRAIGHTS30325- dimensions 293 x 65 mm- thickness 10 mm- dist. between holes37-52 mmWINGS30326- 155 x 308 mm- thickness 6 mm- dist. between holes 45-55- incl. bolt and nut- suitable points S30327 and S30328POINT- dimensions 320 x 70 mm- thickness 10 mm- dist. betweenholes 37-52 mmWING CURVER- 10 mm- for KongskildecultivatorLEFTS30327RIGHTS30328RIGHTA3374418LEFTA3374419HELICAL POINTS - VÄDERSTADleftORDER NUMBER A B C DS30313 left 490 75 10S30314 right 490 75 10MOUNTING BOLTS30324- 12 x 60 mmTINE SUPPORTSORDER NBRS30306S30307S35356SUITABILITYfor 30 x 30 tines and 80 x 80 bodyfor 30 x 30 tines and 100 x 100 bodyfor 35 x 35 tines and 100 x 100 bodyT7.25Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

S-TINES16.02.2009S-TINE12 x 32 mmT0780- with 6 x 40 x 190 mmpointPointT0782- size6 x 40 x 210 mmBolt+ nutT0783SpecialpointT0782ASpecialpointT0782BSpecialpointT0782CS-TINE12 x 45 mmT0755- with 6 x 50 x 265 mmpointPointT0756- size6 x 50 x 265 mmPointT0782D- forged point- size 210 x 17 mm- replace traditional point without adjustments- suitable for Väderstad Agrilla (302300)- incl. bolt and nutBolt + nutT0757- bolt 10 x 45 mm- hardness 8.8VERTICAL TINE12 x 32 mmT0750- with 6 x 40 x 215 mmpointPointT0752- size6 x 40 x 215 mmBolt + nutT0783ROUNDHARROW TOOTH28 x 300 mmS400703- for Väderstad harrow- diameter of mounting hole 16 mmS-TINE POINT SETST0781 25 pcs set- HD- size 6 x 40 x 210 mm- incl. bolts and nutsT0781A 20 pcs set- HD Extra- size 8 x 40 x 210 mm- incl. bolts and nuts- 30 % longer service lifeT7.26Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

S-TINES16.02.2009FASTENERS FOR S-TINES T0780 AND T0750BODY TINE MATERIAL WEIGHT PACKAGE ORDERSIZE SIZE THICKNESS /PC NUMBER50 x 12 32 x 12 50 x 6 0,25 kg 20 T078450 x 12 32 x 12 50 x 8 0,30 kg 20 T0784HD50 x 50 32 x 12 50 x 8 0,44 kg 20 T0784AFASTENERS FOR S-TINE T0755BODY TINE MATERIAL WEIGHT DIMENSION ORDERSIZE SIZE THICKNESS /PC H NUMBER50 x 50 45 x 10 65 x 6 0,35 kg 60 T076450 x 50 45 x 12 70 x 8 0,70 kg 62 T075860 x 60 45 x 10 70 x 8,5 0,70 kg 70 T0764A60 x 60 45 x 12 70 x 10 0,90 kg 72 T0758A70 x 70 45 x 12 70 x 10 0,95 kg 82 T0758BHARROW FRONT LEVELLERTOOTHT0760003310085- size 45 x 10 mmT7.27Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

HANKMO, KELA, HARROW01.12.2009HankmoROTARY HARROW-BLADE- material bordon steel- for 30 mm quadrant axle- dimensions: width 70 mm, thickness 10 mm, length 370 mm- weight 1,35 kgLeftSHX583RightSHX582HARROW SPRING TINES AND SUPPORTSø dTine10 x 425 mmS1131- a = 425 mmb = 103 mmc = 98 mmd = 10 mmSupportS1133- body 40 x 40 mm- consists of the partsS1133A and S1133BTine12 x 485 mmS1132- a = 485 mmb = 107 mmc = 107 mmd = 12 mmSupportS1134- body 40 x 40 mm- consists of the partsS1134A and S1134B96105HARROW SPRING TINE12 x 480 mmS400975- for Väderstad, Multiva, Potila, BBG,Douplet-Record, Kverneland, Evers AgroHARROW SPRING TINE12 x 550 mmS306239- for Väderstad, Dalbo, Rabe, TumeT7.28Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

SEEDING MACHINE WEARING PARTS31.07.2008Väderstad Rapid 300C, 400 CoikeaSEED SHARELeftS306530SEED SHARERightS306531HUBS413930HUBSEALS413944BEARINGS405814- hole Ø 30 mm- outer Ø 62 mm- width 24 mmDISC COULTER400 mmA305580DISC COULTERSEALS415710T7.29Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

TINES FOR ROTARY HARROWS16.02.2009KUHNS52503700MASHIO HB-HM/HL- thickness 10 mmLeftS10100226RightS10100225T7.30Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

TINES FOR ROTARY HARROWS01.06.2009Which way to look your harrow?LeftRightRightRightRightMASHIOMASHIOHOWARD(POMO, KESLA)RightS36100211LeftS36100210RightS27100211LeftS27100210LeftS63592RightS63593RightRightRightHOWARDMALETTIKRONELeftS9923RightS9924LeftS0100077RightS0100078LeftS0354350RightS0352681T7.31Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

JF 80, 90, 110, 800, 900BLADES2064-103ABLADES FOR CHOPPERS(change in pairs)16.02.2009SUPERLUOKO, TUPLAJUNKKARICUTTING BLADES733080CHOPPINGBLADES733125BUSHINGS733083TAARUP 622BLADES58787000YLÖ, JUNKKARI TS150, TS170BLADES2064-103AKNIFE BLADE5260S304006205S304007183- hole 25,5 mm - hole 26 mm527634T7.32Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

BLADES FOR CHOPPERSTUHTI JUNKKARI 1350, 1490BLADES1504075- 2 holesBUSHINGS12170200SUPPORTS1500000PINS80150400- hardenedBOLTPK12040- kgNUTPML12000- kgTAARUP 1100, 1350, 1500BLADES40882300- 1 holeBUSHINGS40881100SUPPORTS40800000BOLTPK14040- kgNUTPML14000- kgVARSTA 1250, 1500BLADESV100BOLTPK14040- kgNUTPML14000- kgJF FH1300, FH1450BLADES2129-234SUPPORTS2129-235BOLTPK12040- kgNUTPML12000- kgT7.33Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

HARVESTER CHOPPING BLADES24.08.2007ROTATING BLADERekordS94147341348- weight 220 g/pc- package 25 pcsROTATING BLADERekordS94147440150- weight 170 g/pc- package 25 pcsROTATING BLADERekordS941552- weight 200 g/pc- package 25 pcsROTATING BLADERekordS94155544280-44243- weight 240 g/pc- package 25 pcsCOUNTER BLADERekord oldS94147540151 old- weight 150 g/pc- package 25 pcsCOUNTER BLADERekord newS94147640151 new- weight 140 g/pc- package 25 pcs50ø20175 4,5COUNTER BLADERekord JD, ClaasS9415650600300, Z35241- weight 170 g/pc- package 25 pcsROTATING BLADERekord with bushingS4444344443- weight 240 g/pc- package 25 pcsROTATING BLADEBisoS941566288014050032,288014050014, 28-14- weight 170 g/pc- package 25 pcsROTATING BLADEBisoS941568JDZ53454, JDZ48237,28.801.405.0034,NH 746813, 743557- weight 230 g/pc- package 25 pcsROTATING BLADEBisoS941570Z42176- weight 170 g/pc- package 25 pcsCOUNTER BLADEBisoS94156728801402001728259044, 28-09- weight 270 g/pc- package 20 pcsT7.34Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

GRAIN LIFTERS135135573573S610272610.272.3- Claas (earlier model)S610294610294.3- Claas (later model)S112AS 112, AZ 30962- John Deere, Deutz FahrS127AS 127- Sampo, MF, New Holland, Clayson11575515S100AS 100- Schumacher blade system- Deutz Fahr, John DeereS150581800700201- joint universal model, cast ironNUTS19190ECR482568- 2 splinesT7.35Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

DOUBLE FINGERSØ 10,576106182S676235676235.0- ClaasSZ11228Z11228- John Deere (earlier model)S80379720RV0498838, 80379720, 379720- Sampo, New Holland, ClaysonS62367560623.6756- Deutz Fahr (earlier model)SZ1178541010001, Z11785- Schumacher blade system- Deutz Fahr, John DeereS609993M91609993M91- MF (later model)S640591M91640591M91- MF (earlier model), Sampo 360T7.36Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

COMBINE KNIFE SECTIONS AND RIVETSS940615S6503530COMBINE KNIFE SECTIONSORDER NUMBER MODEL A B C D E F SUITABLE FOR E.G.S429938 notched 50,8 80,0 16,0 5,5 2 25,5 Volvo-BM429938S23700 notched 50,8 82,5 19,0 5,5 2 35,0 MF, Sampo206236M1, P23700S206236M1H notched 50,8 82,5 19,0 5,5 2,75 35,0 MF, Sampo206236M1HS940615 smooth 51,5 80,0 15,5 5,5 2 25,5DIN80S940613 notched 51,5 80,0 15,5 5,5 2 25,5 Claas, Deutz-FahrDIN80S6503530 notched 51,5 80,0 15,5 6,5 2,75 25,5 Deutz-Fahr, JD06503530 hole in the middleS611203 notched 51,5 83,0 19,0 6,5 2,75 30,0 Claas611203.1S365110 notched 52,4 82,5 19,0 5,5 2,75 29,0 Clayson, NH365110S309197 notched 52,4 82,5 19,0 5,5 2,75 34,0 Clayson, NH309197S49650 notched 50,8 82,5 19 6,5 2,75 35 JD49650HRIVETSCOUNTERSUNKBALL-HEADEDORDER SIZE PACKAGENUMBER1 kg bagS940 14 x 5,3 approx. 360 pcsS941 24 x 5,3 approx. 320 pcsORDER SIZE PACKAGENUMBER1 kg bagS940K 14 x 5,3 approx. 360 pcsS941K 24 x 5,3 approx. 320 pcsS942K 16 x 6,3 approx. 173 pcsS943K 25 x 6,3 approx. 127 pcsT7.37Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

BLADES01.12.2009BLADE MODELSS940623S56110300S58372S58699Model 1Model 2 Model 3 Model 4 Model 5 Model 6ORDER NUMBER SUITABILITY MODEL A B C Ø PACKAGES2220-101A JF, Junkkari 1 90 42 4 20,5 25S940623 Fahr, Welger 1 90 40 3 19 25S940622 Fahr, Eho, Farenblose 1 96 40 3 19 25S58372 Taarup, Estre 1 109 40 3 20,5 25S1100 Ylö TS170, Nokka HS185, Junkkari 1 110 45 4 18,5 25S401503 Luoko, Nokka 1 117 41 4,3 18,5 25SCM120 ZTR, PZ, Pottinger 2 105 47 3 21 25S50571 Elho 14/Kone 320, 280 HKN towed 3 105 50 3 16 25S1120 Elho 200.240 3 115 50 4 20,8/23 25S139800 Krone 243 field chopper 3 117 50 4 19 25S56110300 Taarup, Welger, JF, Kuhn, Elho 3 127 50 4 20,8/23 25S13800013 JF, Freudendahl, Stoll 3 132 50 3 20,5/22,8 25S13800001 JF 4 94 50 4 20,5/24 25S56151200 Kuhn, Esa, JD left 5 93 40 3 16 25S56151300 Kuhn, Esa, JD right 5 93 40 3 16 25S56151210 Kuhn Pegoraro left 5 95 45 3,5 16 25S56151310 Kuhn Pegoraro right 5 95 45 3,5 16 25S55903310 Kuhn left 5 107 45 4 18,2 25S55903210 Kuhn right 5 107 45 4 18,2 25S1448251 Krone 242, JF left 6 90 49 4 19 25S1448261 Krone 242, JF right 6 90 49 4 19 25S0982150800 Welger left 6 90 41 3 19 25S0982150900 Welger right 6 90 41 3 19 25ST673L Mörtl, left 6 94 48 3 23 25ST673R Mörtl, right 6 94 48 3 23 25S1466910 Krone left 6 96 48 4 19 25S1466900 Krone right 6 96 48 4 19 25S570679 Mörtl, Niemeyer, Claas left 6 106 48 4 19 25S570680 Mörtl, Niemeyer, Claas right 6 106 48 4 19 25S1121 Junkkari field chopper left 6 110 47 3 21 25S1122 Junkkari field chopper right 6 110 47 3 21 25S1398881 Krone left 6 112 48 4 19 25S1398891 Krone right 6 112 48 4 19 25S478640 Fella, Lely, Pöttinger, Vicon right 6 120 48 4 18,5 25S478641 Fella, Lely, Pöttinger, Vicon left 6 120 48 4 18,5 25S58699 Ylö, Nokka, Pomo, Vicon left 6 120 50 4 18,5 25S58700 Ylö, Nokka, Pomo, Vicon right 6 120 50 4 18,5 25S56110900 Taarup, Kverneland left 6 126 48 4 20,8/23 25S56110400 Taarup, Kverneland right 6 126 48 4 20,8/23 25S56110500 Taarup 6 131 50 4 20,5/23 25T7.38Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

BOLTS AND HOLDERSCOMPLETE BLADE HOLDERWelgerCYLINDRICAL BOLTNokka, LuokoS4N0120S32900501093290050109, 3202010332- earlier model, 167 mm- for SM4, SM6, SM400, SM600- pin S320201S3208013208010347, 3202010328, 3208010328- later model, 183 mm- for SM4, SM6, SM400, SM600- pin S320201BOLTVicon, NokkaS30577100- 81160, 900.811 60BOLTKuhn, TaarupS56115800- 165.458.01BOLTKuhnS56210100BOLTTaarupS56403000BOLT + NUTKroneS141053BOLT M12Vicon, GreenlandSB1374593T7.39Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

HAY SPRINGS16.02.2009leftleftSPRING FOR CENTRIFUGAL TEDDERYlö- package 20 pcsSPRING FOR CENTRIFUGAL TEDDERFarenblose- package 20 pcsLeftS2101875- yellowRightS2101876- blueLifter springS42464- 4 pcs/spring- package 50 pcsLeftS511042- green- replaces spring S511066RightS511043- yellow- replaces spring S511067vasenSPRING FOR ROTARY TEDDERJF- package 20 pcsLeftS14330201- redRightS14330200- orangeSPRING FOR COIL TEDDERNokkaS3U0010- black- package 50 pcsSPRING FOR COIL TEDDERElho, Sato, YlöSRK51- black- package 50 pcsSPRING FOR CHAIN RAKERS5-034- black- package 50 pcsT7.40Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

HAY SPRINGS16.02.2009SPRING FOR CHOPPERJF 80, 90, 110, 800, 900, 1100S1433050614350027- package 50 pcsSPRING FOR BALERWelger, ClaasS0940522500- 10 mm mounting bolt- package 50 pcsSPRING FOR HARD BALERJohn Deere 330, 332, 336, 339S19692- package 20 pcsSPRING FOR CARRIAGEKroneS9381480- package 50 pcs- black75 1585,5391927SPRINGKrone, Ylö, JunkkariS93791900- for Krone carriage, Krone baler, Ylö carriage,Junkkari TS150 chopper- package 50 pcsT7.41Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

TINES FOR FRONT LOADERS KVERNELAND TYPE08.06.2006picture 1picture 2S221191- length 600 mm, weight 2,85 kg- tines are delivered with nuts, thread M20x1,5ORDER LENGTH WEIGHT PICTURENUMBERS221150 600 mm 3,4 kg 1S221151 810 mm 3,7 kg 1S221152 1100 mm 6,1 kg 1S221193 680 mm 3,4 kg 2S5068015- bended Ålö-tin- length 800 mm, weight 4,1 kg- tines are delivered with nuts, thread M24x1,5Tines are delivered with nuts, thread M20x1,560Ø 45Ø 26Ø 3735BUSHINGCone 1S221BUSHINGCone 1 longS222BUSHINGCone 1S223110BUSHINGCone 2S241120ORDER LENGTH WEIGHTNUMBERØ 60Ø 32Ø 46S241160 810 mm 6,3 kgS241161 980 mm 8,3 kgS241162 1250 mm 11,6 kgS241163 1400 mm 13,4 kgTines are delivered with nuts, thread M28x1,5BUSHINGCone 2S241HDØ 145T7.42Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

FRONT LOADER ADAPTER SETS01.06.2009- front loader adapter sets aredelivered in pairs L + R- the supports welded on base platecan be welded as such to bucketor other front loader machinery- delivered unpaintedADAPTER SETIsmeS7640NOTE!Remote control cables forfront loaderson section T8- mounting width from the inner edge oflower brackets 645 mm- delivered in pairs L + RADAPTER SETQuickS7620ADAPTER SETSolid/PehtooriS7680Mounting width1240 mm- for early typeQuick and Pika-Quickloaders- delivered in pairs L + RMountingwidth 857 mm- for Solid/Pehtooriloaders- delivered in pairs L + RMountingwidth 930 mmADAPTER SETEuroS7600Mounting width990 mmADAPTER SETValtra, VilaS7630- for loadersequipped witheuro-brackets Mounting width 736 mm(Ålö, Trima, Valtra)- delivered in pairs L + R- for Valtra and Vilaloaders- delivered in pairs L + RMounting width1020 mmADAPTERSET- for Volvo BM loaders(partly)- delivered in pairs L + RADAPTERSETTrima, MPS7610Industrial modelS7660- support 30 x 170 x 782 (outerdimensions), lower hole 56Industrial model IIS7670- support 30 x 135 x 600 (outerdimensions), lower hole 56- for Trima andMP-Lift loaders- delivered in pairs L + RMounting width690 mmADAPTER SETBobcat all modelsS7690- delivered in pairs L + R- setting dimensions vary depending on types- thickness 8 mm33200 mm 50408 mm117T7.43Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

BUCKET TEETH16.02.2009ABUCKETTEETHHORDER L/L1 A B H WEIGHTNUMBER mm mm mm mm kgKK200142 485/145 57 92 58 12 kgLL1BBUCKET TEETH FOR TRACTORDIGGERAHLORDER L A B H WEIGHTNUMBER mm mm mm mm kgKK200107 286 40 70 40 4B- locking pin 20 x 90 KK200584- repair pieces:KK200098(L95, B110, B 1 95, H50, 2,3 kg)KK200360(L125, B95, B 1 80, H50, 2,4 kg)HB 1LB- bushing KK200108 P175, L73, K52,weight 2,0 kg- locking pin 13 x 75 KK200591- repair piece KK200096(L75, B80, B 1 72, H42, 0,8 kg)HB 1LBAHB-LOCKBUCKET TEETHLL 1BLORDER L/L 1 A B H WEIGHT BUSHING LOCKINGNUMBER mm mm mm mm WEDGEKK200673 228/93 36 61 36 2,2 kg KK200608 KK200700L119, B62, H50, weight 1,0 kgKK200671 310/119 42 65 44 3,7 kg KK200607 KK200701L157, B75, H61, weight 1,9 kgBHT7.44Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

HBUCKET TEETH01.12.2009BUCKET TEETH AND ADAPTERS, CAT-TYPEA2LAORDER ORIGINAL DESCRIPTION ENGINE A A2 H L WEIGTHNUMBER CAT NUMBER TYPE mm mm mm mm kgKK20301 1U3252 ground tooth, long J250 60 70 85 190 2,9KK20302 1U3302 ground tooth, long J300 70 85 95 220 4,6KK20303 1U3352 ground tooth, long J350 85 95 110 245 6,0KK20304 1U3452 ground tooth, long J450 115 125 130 300 12,2KK20305 1U3552 ground tooth, long J550 140 155 150 340 19KK20403 9N4352 excaviation tooth, long J350 85 95 115 255 8KK20404 9N4452 excaviation tooth, long J450 115 130 140 320 16,2KK20405 9N4552 excaviation tooth, long J550 140 155 160 350 24,5KK21101 6Y3254 adapter J250 for 25 mm front scoop plate, weldable 4,2KK21102 3G6304 adapter J300 for 30 mm front scoop plate, weldable 7,4KK21108 6I6354 adapter J350 for 35 mm front scoop plate, weldableKK21103 3G8354 adapter J350 for 40 mm front scoop plate, weldable 8,0KK21104 8E6464 adapter J450 for 50 mm front scoop plate, weldable 21KK21105 6I6554 adapter J550 for 60 mm front scoop plate, weldable 31ORDER ORIGINAL DESCRIPTION ENGINE DIAMETER LENGTHNUMBER CAT NUMBER TYPE mm mmKK22101 8E6258 pin J250 14,2 77KK22102 9J2308 pin J300 14,2 92KK22103 9J2358 pin J350 19 105KK22104 8E0468 pin J450 23,7 133KK22105 6Y8558 pin J550 25,4 160ORDER ORIGINAL DESCRIPTION ENGINE HOLE OUTER DIAMETER OUTER DIAMETERNUMBER CAT NUMBER TYPE SIZE OF METAL PART OF PLASTIC PARTKK23102 8E6259 locking ring J250/J300 14,2 27 32KK23103 8E6359 locking ring J350 19 38 41KK23104 8E8469 locking ring J450 23,7 38 41KK23105 8E5559 locking ring J550 25,4 47 52T7.44aOriginal manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

FRONT SCOOP PLATES16.02.2009FRONT SCOOP PLATES500 HB- install weldable front scoop plate into tractor front loader orsimilar targets- other edge is canted- can be installed also by welding into tractor rear plate as an bladeORDER WIDTH THICKNESS LENGTH WEIGHTNUMBER mm mm mm kgS93121450 110 12 1450 14S93122050 110 12 2050 20S93122400 110 12 2400 23S93122700 110 12 2700 26S93161450 150 16 1450 26S93162050 150 16 2050 37S93162400 150 16 2400 43S93162700 150 16 2700 48ARROWHEAD PROFILES94103000- length 3 m, weight 9,2 kg/m- hardness HB500- W=101 mm, W1=46 mm, T=11 mm, T1=21 mmW1S94153000- length 3 m, weight 20,5 kg/m- hardness HB500- W=151 mm, W1=68 mm, T=16 mm, T1=32 mmT1WTT7.44bOriginal manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

SNOW BUCKETS09.10.2009SNOW BUCKETS- made of Rautaruuki’s constructional steel- material used in STD buckets PL4-S250 LASER or PL4-5355 LASER- minimum material used in HD buckets PL5-S355 LASER- material thickness 4 mm STD, 5 mm HD- reinforcement thickness 8 mm STD, 10 mm HD- made in FinlandThe Key Flag is a guaranteeof domestic materialsand control of traceabilityCABORDER MODEL WEIGHT WIDTH DEPTH HEIGHT FRONT ADAPTERNUMBER kg mm mm mm SCOOP PLATEmmTY0270000 STD 340 2700 850 1020 120 EuroTY0270010 STD 340 2700 850 1020 120 Trima, MPTY0270020 STD 340 2700 850 1020 120 QuickTY0270030 STD 340 2700 850 1020 120 Valtra, VilaTY0270040 STD 340 2700 850 1020 120 IsmeTY0270080 STD 340 2700 850 1020 120 Solid, PehtooriTY0270100 HD 415 2700 850 1020 160 EuroTY0270110 HD 415 2700 850 1020 160 Trima, MPTY0270120 HD 415 2700 850 1020 160 QuickTY0270130 HD 415 2700 850 1020 160 Valtra, VilaTY0270140 HD 415 2700 850 1020 160 IsmeTY0270180 HD 415 2700 850 1020 160 Solid, PehtooriTY0240000 STD 315 2400 800 1000 120 EuroTY0240010 STD 315 2400 800 1000 120 Trima, MPTY0240020 STD 315 2400 800 1000 120 QuickTY0240030 STD 315 2400 800 1000 120 Valtra, VilaTY0240040 STD 315 2400 800 1000 120 IsmeTY0240080 STD 315 2400 800 1000 120 Solid, PehtooriTY0240100 HD 380 2400 800 1000 160 EuroTY0240110 HD 380 2400 800 1000 160 Trima, MPTY0240120 HD 380 2400 800 1000 160 QuickTY0240130 HD 380 2400 800 1000 160 Valtra, VilaTY0240140 HD 380 2400 800 1000 160 IsmeTY0240180 HD 380 2400 800 1000 160 Solid, PehtooriT7.44cOriginal manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

BUCKETS01.12.2009BUCKETS- made of Rautaruuki’s constructional steel- material used in STD buckets PL4-S250 LASER or PL4-5355 LASER- minimum material used in HD buckets PL5-S355 LASER- material thickness 4 mm STD, 5 mm HD- reinforcement thickness 8 mm STD, 10 mm HD- made in FinlandThe Key Flag is a guaranteeof domestic materialsand control of traceabilityCABORDER MODEL WEIGHT WIDTH DEPTH HEIGHT FRONT ADAPTERNUMBER kg mm mm mm SCOOP PLATEmmTY1205000 STD 215 2050 720 810 120 EuroTY1205010 STD 215 2050 720 810 120 Trima, MPTY1205020 STD 215 2050 720 810 120 QuickTY1205030 STD 215 2050 720 810 120 Valtra, VilaTY1205040 STD 215 2050 720 810 120 IsmeTY1205080 STD 215 2050 720 810 120 Solid, PehtooriTY1205100 HD 270 2050 720 810 160 EuroTY1205110 HD 270 2050 720 810 160 Trima, MPTY1205120 HD 270 2050 720 810 160 QuickTY1205130 HD 270 2050 720 810 160 Valtra, VilaTY1205140 HD 270 2050 720 810 160 IsmeTY1205180 HD 270 2050 720 810 160 Solid, PehtooriTY1145050 STD 103 1450 650 610 120 AvantTY1170090 STD 165 1700 850 650 120 BobcatTY1145000 STD 150 1450 650 770 120 EuroTY1145010 STD 150 1450 650 770 120 Trima, MPTY1145020 STD 150 1450 650 770 120 QuickTY1145030 STD 150 1450 650 770 120 Valtra, VilaTY1145040 STD 150 1450 650 770 120 IsmeTY1145080 STD 150 1450 650 770 120 Solid, PehtooriTY1205090 STD 195 2050 850 650 140 BobcatTY1145100 HD 190 1450 650 770 160 EuroTY1145110 HD 190 1450 650 770 160 Trima, MPTY1145120 HD 190 1450 650 770 160 QuickTY1145130 HD 190 1450 650 770 160 Valtra, VilaTY1145140 HD 190 1450 650 770 160 IsmeTY1145180 HD 190 1450 650 770 160 Solid, PehtooriT7.44dOriginal manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ASPHALT CUTTERS AND EMPTYING VALVE09.10.2009ASPHALT CUTTERS7800- quick mounting model (mounting with 2x24 mm bolts)- for max. 35 mm lip plate- cutter disc Ø 360 mm, axle 45 mm- weight approx. 45 kg- recommended for use in max. 12 tn diggersSPARE DISC 360 mmS7800A- including axle and centre bearingEMPTYING VALVE FORFLEXIBLE INTERMEDIATEBULK CONTAINERS7900SORTING HOOK FOR FLEXIBLEINTERMEDIATEBULK CONTAINERAK25141- load 2 tons- sf 5:1 (ultimate load)- grade 7- weight 2,84 kg- dimensions:L = 246 mmA = 34,9 mmB = 50,8 mmO = 71,4 mmR = 15,8 mm- UV-protected HD-PE material- tube equipped with quick-lock- makes partial emptying possible- quick to install, domestic patented quality product- also suitable for pelletsT7.45Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ROAD MACHINE BLADES, QUICK CLAMPING01.12.2009LONG LIFE 500BLADESCovering range of domestic blades made of high quality Imabors-steel.Delivery hardness tempered 460-510 HB.MEANING OF ORDER NUMBER:SC2 1 1 2 X X X X X X ABlade type:Letter in the end:1=straight toothed2=concave toothed3=flat4=side5=special6=leveller (rear plate)7=snow plough8=mesh9=front scoop plateThicknessmmHole pitch:0=290 mm1=305 mm2=mesh3=no holesBladewidthmmA=flatB=toothedC=toothed/flatQUICK CLAMPING BLADESCONCAVE TOOTHED BLADES (ice shredder blade)- hole pitch 305 mmORDER WIDTH THICKNESS LENGTH HOLES WEIGHTNUMBER mm mm mm kg- grader- vehicle chassis- snow ploughSC2112915 193 12 915SC21121220 193 12 1220 2 x 4 14,6SC21121525 193 12 1525 2 x 5 18,3STRAIGHT TOOTHED BLADES- hole pitch 305 mmORDER WIDTH THICKNESS LENGTH HOLES WEIGHTNUMBER mm mm mm kg- grader- vehicle chassis- snow ploughSC1112792 200 12 792 2 x 3 10,0SC1112915 200 12 915 2 x 3 13,0SC11121220 200 12 1220 2 x 4 16,0SC11121525 200 12 1525 2 x 5 20,0FLAT BLADES- hole pitch 305 mmORDER WIDTH THICKNESS LENGTH HOLES WEIGHTNUMBER mm mm mm kg- grader- vehicle chassis- snow ploughSC3112792 200 12 792 2 x 3 14,4SC3112915 200 12 915 2 x 3 16,8SC31121220 200 12 1220 2 x 4 22,8SC31121525 200 12 1525 2 x 5 28,5T7.46Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ROAD MACHINE BLADES, BOLT CLAMPING01.12.2009BOLT CLAMPING BLADESCONCAVE TOOTHED BLADES(ice shredder blade)- hole pitch 290 mmC- grader- levellerORDER WIDTH THICKNESS LENGTH C HOLES WEIGHTNUMBER mm mm mm mm kgSC20121690 193 12 1690 120 2 x 6 20,2SC20121980 193 12 1980 120 2 x 7 23,7SC20122440 193 12 2440 60 2 x 9 29,3SC20123020 193 12 3020 60 2 x 11 36,2STRAIGHT TOOTHED BLADES- hole pitch 290 mmC- grader- levellerORDER WIDTH THICKNESS LENGTH C HOLES WEIGHTNUMBER mm mm mm mm kgSC1012460 200 12 460 85 2 x 2 6,5SC1012750 200 12 750 85 2 x 3 10,6SC10121690 200 12 1690 120 2 x 6 23,8SC10121980 200 12 1980 120 2 x 7 27,2SC10122440 200 12 2440 60 2 x 8 34,4SC10123020 200 12 3020 60 2 x 10 42,5FLAT/STRAIGHTTOOTHED BLADES- towed levellers and rear platesORDER WIDTH THICKNESS LENGTH WEIGHT HOLESNUMBER mm mm mm kg- rear plate- levellerLetter in the end of the order number:A = flatB = toothedC = toothed/flatSC60102500A 200 10 2500 35,0 290SC60102500B 200 10 2500 35,0 290SC61102500A 200 10 2500 35,0 305SC61102500B 200 10 2500 35,0 305SC60103000A 200 10 3000 42,0 290SC60103000B 200 10 3000 42,0 290SC61103000A 200 10 3000 42,0 305SC61103000B 200 10 3000 42,0 305SC60122500C 200 12 2500 40,0 290SC61122500C 200 12 2500 40,0 305SC60123000C 200 12 3000 49,0 290SC61123000C 200 12 3000 49,0 305FLAT BLADES- hole pitch 290 mmC- grader- leveller- snow ploughORDER WIDTH THICKNESS LENGTH C HOLES WEIGHTNUMBER mm mm mm mm kgSC3012490 200 12 490 80 2 x 2 9,2SC30121698 200 12 1698 104 2 x 6 32,0SC30121988 200 12 1988 104 2 x 7 37,2SC30122440 200 12 2440 40 2 x 9 46,0SC30122520 200 12 2520 80 2 x 9 47,3SC30123020 200 12 3020 40 2 x 11 56,7T7.47Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

ROAD MACHINE BLADES, MESH EDGES AND ACCESSORIESMESH EDGES- hole pitch 305 mm01.12.2009ORDER WIDTH THICKNESS LENGTH WEIGHTNUMBER mm mm mm kgSC8211692 240 11 692 7SC8211792 240 11 792 8SC8211915 240 11 915 9SC82111220 240 11 1220 12SC82111525 240 11 1525 15STINGERBLADESLong collar: for motor graders (low speed).Short collar: under car (high speed), better mounting, main blade must be slotted (for nodule).Ø 16,4Ø 16,4Ø 16,4Ø 16,482Ø 3389,5Ø 3785,2Ø 37,585,5Ø 33Ø 19,4Ø 19,4Ø 19,4Ø 19,4S11030010- sharp/narrow- long collarS11030071- sharp/wide- short collarS11030026- sharp/wide- long collarS11030148- sharp/narrow- short collarMESH EDGESWITHSIDE PROTECTION- usage for e.g. drags, back drags, joint ploughs, vertical ploughs- benefit: protects the main blade sides (for e.g. pavements)TTT8211885- 240 x 11 x 885 mm- for blade 692 and 792TTT8211995- 240 x 11 x 995 mm- for blade 915TTT82111270- 240 x 11 x 1270 mm- for blade 1220LOCK HEAD BOLTSBLADE ACCESSORIESWEDGELORDER NBR SIZE PACKAGEPL1604588 16 x 45 mm 50 pcsPL1605088 16 x 50 mm 50 pcsPL1605588 16 x 55 mm 50 pcsPL1606088 16 x 60 mm 50 pcsPL1607088 16 x 70 mm 50 pcsCOTTER BOLTORDER NBR SIZE PACKAGESC47 47 mm 25 pcsSC53 53 mm 18 pcsSC65 65 mm 50 pcsORDER NBR SIZE PACKAGESC205 20,5 mm 20 pcsSC245 24,5 mm 20 pcsSC26026 mmNUTSORDER NBR TYPE PACKAGEPM16000 nut M16 5 kgPML16000 nut M16 nyloc 5 kgSC16 collar nut M16 50 pcsSC16N collar nut M16 nyloc 50 pcsT7.48Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLANT PROTECTION SPRAYER NOZZLE HOLDERSInstallation of Zip Fit - nozzle to the hose is made simple with theself-threading screw.Characteristics and the materials used ensures excellent resistanceagainst pressure, strong chemicals and shocks.The anti-drip device is equipped with simple calibrating system whichensures opening and closing regularly.Fast and safe installationNew anti-dripmembrane systemCompletely new,closed bayonet capNOZZLE HOLDER 1/2”S8000- standard with clamp, self tapping screw, o-ringand anti-drip valve- with EPDM or anti-drip membrane- nut and spray tip not included- operating pressure 1-20 bar- endures max. 40 bar water shocks- anti-drip system opens at 0,7 bar and operates 1,0 bar- material: body fiberglass Nylon 66, EPDM membrane- use: on crop protection booms- packing size: 10AgrotopANEMOMETERVE780- easy to use, compact meter for accurate measuring ofwind velocity- water-proofed- LCD-display- includes hanging belt and batteries- measures mph, km/h, m/s and knotsT7.49Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLANT PROTECTION SPRAYER FILTER16.02.2009PRESSURE FILTERR180 MESHS8051- connect. R1“ inner thread- filtering area 34 cm²- max. flow 150-160 l/min- packing size: 1Spare cartridgeS8056- packing size: 10O-ring forconnectorOR30230- 30,2 x 3,0 mmPRESSURE FILTERR3/4 80 MESHSPARE PARTSSpare cartridgeS8055- packing size: 10O-ring forconnectorOR24230- 24,2 x 3,0 mmPRESSURE GAUGES- thread 1/4“- liquid-damped- bottom fasteningHOSE CONNEC-TORSORDERNUMBERH950024H950026H950027PRESSUREAREA0 - 10 bar0 - 25 bar0 - 40 barORDER THREAD SHANKNUMBERCRC3419 R3/4“ 19 mmCRC3425 R3/4“ 25 mmCRC1019 R1“ 19 mmCRC1025 R1“ 25 mmT7.50Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLANT PROTECTION SPRAYER FLAT SPRAY NOZZLESOPTIONS TO BUILD UP A NOZZLE:According to norm ISO: For HARDI nozzle body For HARDI nozzle bodyaccording to norm ISO: with HARDI nozzle nut:FILTER+SEAL3 mmS8070SEAL3 mmS8063ORFILTERS8070- use without filter(the seal included isnot shown in thepicture)SEAL7 mmS8062FILTER+SEALS8071NOZZLENOZZLENOZZLENOZZLENUTS8032NOZZLENUTS8032NOZZLENUTHardiS8033- incl. seal S8063- 66 % nylon + 30 % fiberglass- incl. seal S8063- 66 % nylon + 30 % fiberglass- 66 % nylon + 30 % fiberglass- for Hardi nozzles- according to ISO-standard- 110 O- material Kematal- for spraying plantprotection agents- packing size: 25 pcsYELLOWS8010- filteringrequirementMESH 60- ISO11002BLUES8011- filteringrequirementMESH 40- ISO11003REDS8012- filteringrequirementMESH 40- ISO11004Kematal PLANT PROTECTION SPRAYER NOZZLESPRESSURE CAPACITY 4 km/h 6 km/h 8 km/h 10 km/h 12 km/h 14 km/hbar l / min l/ha l/ha l/ha l/ha l/ha l/ha1 0.46 138 92 69 55 46 392 0.65 195 129 97 77 64 553 0.79 237 158 118 95 79 684 0.91 273 182 137 109 91 785 1.02 306 205 153 112 102 876 1.12 336 225 168 134 112 967 1.21 363 240 182 145 121 1048 1.3 390 260 195 155 130 1119 1.37 411 275 205 164 137 11710 1.44 432 288 215 173 144 1231 0.69 207 138 103 83 69 592 0.97 290 195 145 116 97 833 1.18 354 240 178 142 118 1014 1.37 410 270 210 164 137 1175 1.53 460 305 230 184 153 1316 1.67 500 335 250 200 167 1437 1.8 540 360 270 215 180 1548 1.93 580 385 290 232 193 1659 2.04 610 408 305 245 204 17510 2.15 645 430 323 258 215 1821 0.91 273 182 137 109 91 782 1.29 387 260 193 155 129 1113 1.58 474 320 240 189 158 1354 1.82 544 360 270 220 182 1565 2.04 610 408 305 245 204 1756 2.23 670 445 335 268 223 1917 2.41 720 480 362 290 241 2078 2.6 780 520 390 312 260 2239 2.74 820 550 411 329 274 23510 2.88 865 575 432 346 288 247The results above has been reached by using water and by measuring the pressure with pressure gauge which has been placed right beside thenozzle.T7.51Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

FLAT SPRAY NOZZLE TWINAlbus AVI TWIN- very high accuracy- high wear resistance, material plastic- spray angle 2 x 110 o- flow rate 2-7 according to ISO standard- pressure range 2-7 bar, optimal 5-7 bar- recommended boom height 40-60 cm- application: boom spraying and horticulturee.g. potato and strawberry cultivationYELLOWS8015BLUES8016REDS8017T7.52Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

09.10.2009OPTIONS TO BUILD UP A NOZZLE:According to norm ISO: For HARDI nozzle bodyaccording to norm ISO:For HARDI nozzle bodywith HARDI nozzle nut:FILTER+SEAL3 mmS8070SEAL3 mmS8063PLANT PROTECTION SPRAYER AIR NOZZLESORFILTERS8070- use without seal(seal included isnot shown in thepicture)SEAL7 mmS8062FILTER+SEALS8070NOZZLENOZZLENOZZLENOZZLENUTS8032NOZZLENUTS8032NOZZLENUTHardiS8033- incl. seal S8063- 66 % nylon + 30 % fiberglass- incl. seal S8063- 66 % nylon + 30 % fiberglass- 66 % nylon + 30 % fiberglass- for Hardi nozzlesAIR MIXNOZZLES- suitable for most common nozzle bodies in the market such asAgrotop, Arag, Exel, Ylö, Junkkari, Teejet ja Hardi *(* for part of them needed seal S8062 and nut S8032)- larger size of drop makes the efficiency better andthe effect of wind velocity is smaller- big drop which contains air kind of explodes when in touch withgrowth and spreads smoothly- can be sprayed even in wind velocity 5 m/s- for pressure range 1,5 - 6 bar (optimal pressure 2,5 bar)- can be also used with liquid fertilizers,then reduce 13 % from the capacity- new air cleaning system- height only 10 mm higher as standard nozzle- two-piece construction is easy to clean and openwithout tools, no separate seals- best and easiest way to change the ordinary plantprotection sprayer is to equip it with air nozzles- packing size: 25 pcsPRESS. CAPACITY 4 km/h 5 km/h 6 km/h 7 km/h 8 kmh 10 km/h 12 km/h 14 km/h 16 km/h 20 km/hbar l / min l/ha l/ha l/ha l/ha l/ha l/ha l/ha l/ha l/ha l/haYELLOWS8080BLUES8081REDS80821,0 0,462 139 111 92 79 69 55 46 40 35 281,5 0,566 170 136 113 97 85 68 57 49 42 342,0 0,653 196 157 131 112 98 78 65 56 49 392,5 0,730 219 175 146 125 110 88 73 63 55 443,0 0,800 240 192 160 137 120 96 80 69 60 484,0 0,924 277 222 185 158 139 111 92 79 69 555,0 1,033 310 248 207 177 155 124 103 89 77 626,0 1,131 339 271 226 194 170 136 113 97 85 681,0 0,693 208 166 139 119 104 83 69 59 52 421,5 0,849 255 204 170 146 127 102 85 73 64 512,0 0,980 294 235 196 168 147 118 98 84 74 592,5 1,095 329 263 219 188 164 131 110 94 82 663,0 1,200 360 288 240 206 180 144 120 103 90 724,0 1,386 416 333 277 238 208 166 139 119 104 835,0 1,549 465 372 310 266 232 186 155 133 116 936,0 1,697 509 407 339 291 255 204 170 145 127 1021,0 0,924 277 222 185 158 139 111 92 79 69 551,5 1,131 339 271 226 194 170 136 113 97 85 682,0 1,306 392 313 261 224 196 157 131 112 98 782,5 1,461 438 351 292 250 219 175 146 125 110 883,0 1,600 480 384 320 274 240 192 160 137 120 964,0 1,848 554 444 370 317 277 222 185 158 139 1115,0 2,066 620 496 413 354 310 248 207 177 155 1246,0 2,263 679 543 453 388 339 272 226 194 170 136T7.53Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.

PLANT PROTECTION SPRAYER TIPCAP NOZZLESOPTIONS TO BUILD UP A NOZZLE:According to norm ISO:FILTER+SEAL3 mmS8063SEAL3 mmS8063ORFor HARDI nozzle bodyaccording to norm ISO:FILTERS8070- use without seal(seal included isnot shown in thepicture)SEAL7 mmS8062NOZZLENOZZLEGERMAN TIPCAP NOZZLES- only two parts needed; seal and nozzle (nozzle and quick nut from one part)- TipCap is suitable for all nozzle bodies in the market such as Agrotop, Arag, Excel, Ylö, Junkkari, Teejet and Hardi- no more troubles with small parts- easy to clean and to change- ISO colours, no confusion- maximal pressure range- spraying angle 110 o- all sizes- integrated filter availableNOZZLE PRESSURE CAPACITY 4 km/h 5 km/h 6 km/h 7 km/h 8 kmh 10 km/h 12 km/hFILTER bar l / min l/ha l/ha l/ha l/ha l/ha l/ha l/haYELLOWS8020ISO11003BLUES8021ISO11003REDS8022ISO110041,5 0.566 170 136 113 97 85 68 57S8070 2,0 0.653 196 157 131 112 98 78 65MESH 50 2,5 0.730 219 175 146 125 110 88 733,0 0.800 240 192 160 137 120 96 804,0 0,924 277 222 185 158 139 111 921,5 0.849 255 204 170 146 127 102 85S8070 2,0 0.980 294 235 196 168 147 118 98MESH 50 2,5 1.095 329 263 219 188 164 131 1103,0 1.200 360 288 240 206 180 144 1204,0 1.386 416 333 277 238 208 166 1391,5 1.131 339 271 226 194 170 136 113S8070 2,0 1.306 392 313 261 224 196 157 131MESH 50 2,5 1.461 438 351 292 250 219 175 1463,0 1.600 480 384 320 274 240 192 1604,0 1,848 554 444 370 317 277 222 185T7.54Original manufacturers names and part numbers are quoted for reference purpose only and are not intended to infer that our replacement parts are used as original equipment.