cast steel gate valves – ansi 300

alton.com.sg
  • No tags were found...

cast steel gate valves – ansi 300

INDEX


INDEXContentPage•• Figure Number 1•• Gate Valves (ANSI 150 to 1500) 2-7•• Globe Valves (ANSI 150 to 1500) 8-13•• Swing Check Valves (ANSI 150 to 1500) 14-19•• Electrically / Gear Operated Valves 20•• Welding End Details 21•• Ring Joint Connection between body andbonnet/cover22•• Reference Standards and Specification 23•• Comparison List for Casting and Forging 24•• Chemical and Physical Properties 25•• Gasket Material & Construction 26-27•• Packing Material & Construction 28•• Pressure Temperature Rating 29•• Steel Pipe Flanges 30-31•• Comparison Chart 32MACHINERY AND TESTING FACILITIESWe have endeavoured in this catalogue to make the information as accurate as possible,but cannot accept any responsibility should it found that in any respect the information isinaccurate or incomplete or becomes so as a result of further developments.


FIGURE NUMBERANSI RATING VALVE TYPE BODY/BONNET MATERIAL END CONNECTION01=ANSI 15003=ANSI 30006=ANSI 60009=ANSI 90015=ANSI 150025=ANSI 2500*0=Plug1=Gate2=Globe3=SwingB=Bevel WeldF=Raised Face FlangeR=Ring Type Joint*Available onrequest1=Low Carbon Steel ASTM A352 LCB/LC3/LCC2=Carbon Steel ASTM A216 Gr. WCB3=Stainless Steel- ASTM A351 CF8M/CF3M/CF10M4= Stainless Steel- ASTM A351 CF8/CF3/CF105= Stainless Steel- ASTM A351 CF8C (Type 347)6=Stainless Steel- ASTM A351 CG8M / CG3M7=Alloy Steel ASTM A217 WC1/WC6/WC9/C5/C128=Alloy 20 ASTM A351 CN7M9=Duplex Stainless Steel0=Hastelloy, Monel or OthersAPITRIMNO123455A6788A91011121314NOMINAL TRIMF6304F310Hard F6HardfacedHardfacedF6 & Cu-NiF6 & Hard F6F6 and HardfacedF6 and HardfacedMonel316Monel & Hardfaced316 & HArdfacedAlloy 20Alloy 20 & HardfacedSEATSURFACEHARDNESS(Hb a Min.)bcc750 d350 d350 d250 f & 175 f300 f & 750 f300 f & 350 f300 f & 350 fccc& 350 fc& 350 fcc& 350 fTRIM MATERIALSEATSURFACEMATERIAL12 Cr18 Cr-8Ni25 Cr-20NiHard 13CrCo-Cr A hNi-Cr13Cr Cu-Ni13Cr & Hard 13Cr13Cr & Co-CR A h13Cr & Ni-CrNi-Cu alloy18Cr-8NiNi-Cu alloy & Trim 5 or 5A18Cr-8Ni & Trim 5 or 5A19Cr-29Ni19Cr-29Ni & Trim 5 or 5AAPITRIMNO151617181920212223242526272829XNOMINAL TRIM316(F-Stl)316L(F-Stl)304(F-Stl)304 & Hardfaced321 (F-Stl)316L347304LB335(Hastelloy B)321316L & Hardfaced321 & HardfacedB574(Hastelloy C)347 & Hardfaced347 (F-Stl)Special MaterialsSEATSURFACEHARDNESS(Hb a Min.)350 d Co-Cr A h350 dc& 350 f350 dccccccc& 350 fc& 350 fcc& 350 f350 dSEATSURFACEMATERIALCo-Cr A hCo-Cr A h18Cr-8Ni & Co-CrA hCo-Cr A h16Cr-12Ni-2Mo18Cr-10Ni-Cb18Cr-8NiNi-Mo Alloy B18Cr-10Ni-Ti16Cr-12Ni-2Mo &Co-CrA h18Cr-10Ni-Ti & Co-CrA hNi-Mo-Cr & Alloy C-27618Cr-10Ni-Cb & Co-CrA hCo-CrA hNOTE:aHB {formerly HBN} is the symbol for BrinellHardness per ASTM E10bBody and gate seat 250HB minimum, with 50 HBminimum differential between the body and gateseatscManufacturer's standard hardnessdDifferential hardness between the body and gateseat surfaces is not requiredeCase hardened by nitriding to a thickness of 0.13mmminimumfHardness differential between body and gate shallbe manufacturer's stdgManufacturer's standard with 30 Ni minimumhThis classification includes such trademarkedmaterials as Stellite 6, Stoody 6; and Wallex 6.IManufacturer's standard hardfacing with 25 percentFe maximumGENERAL NOTES FOR DIMENSIONAL TABLES1. All sizes given in millimeters and inches are approximate.2. All weights given in Kgs are approximate.3. Dimensions shown may be revised at any time. Use certified dimensional drawings for critical areas.1


CAST STEEL GATE VALVES2) Welded-in seat rings, designed in order to prevent anyturbulence and avoid damages due to corrosion. Both areforged or rolled in one piece, for all dimensions, They aretreated to obtain the requested surface hardness, and areperfectly cleaned before assembling.• STEMThe stem has a forged tee-head connection, with rolled orcut ACME threads according to valve size, and is rolled orrectified in the packing area in order to assure a long lifewith a perfect tightness. We have calculated and checkedby means of experiment the stem-wedge connection inorder to prevent the turning or the disengagement of thestem from the wedge while the gate valve is in service. Thestrength of the connection exceeds the strength of the stemat the root of its operating thread.KVC Gate valves are manufactured to API Std.600 andtested to API Std.598Gate Valves are the most commonly used shut-off valve inthe industry today. They are used where minimum pressuredrop and bi-directional on-off service is required. Gatevalves are not designed for throttling service. Prolongeduse in the partially open position will generally damageseating surface.• BODY AND BONNETThe body and bonnet design is calculated to achieve themost regular distribution of stress in all sides, as well asthe minimum turbulence and resistance to flow. Bonnets onall valves are equipped with a back seat bushing.• BODY-BONNET JOINTSBody-Bonnet Joints of gate valve are machined as follows:on 150 class : plain facedon 300 class : male and femaleon 600, 900 and 1500 classes : ring joint• BODY-BONNET GASKETStandard is P#6633, P#2601 & P#1500SAlso available in different type to meet customerrequirement upon request.• WEDGESOLID (TYPE S) FLEX (TYPE F)The valve is normally supplied with a solid wedge for up to2" and flexible wedge for above 2" as shown below. Allwedges are full guided.• SEAT RINGSeat rings are manufactured in two different ways,depending on the class and type of valves:1) Screwed seat rings, bottom seated type lapped on bothsides. They are dry assembled, with a controlled torquedry assembled, with a controlled torque setting to thebody.• GLANDThe gland is made in two pieces: a cylindrical piece incontact with the packing connected through a spherical jointto the gland flange. The particular design of both piecesassures a correct pressure on the packing without injuringthe stem through friction or corrosion.• STUFFING BOXThe design is API Std.600 for high pressure class valvesand over the stuffing box is provided with a lantern ring.• END CONNECTIONSOur standard production covers valve with :Flanged ends (RF) that conform to ANSI B16.5 and face toface dimensions that conform to ANSI B16.10, with a raisedface serrated finish or, on request, with any other type offinish;Butt-welding ends (BW) with end to end dimensions thatconform ANSI B16.10Customer must specify the type of schedule required, orclass of pipe, or diameter and bore.Ring-joint flanged ends (RTJ) that conform to ANSI B16.5,with end to end dimensions to ANSI B16.10Other special end connections are supplied to customers'special requirements.• HANDWHEELHandwheels are of a particular design, for easy operation;dimensions are according to API 600: they are made inductile iron.• GEAR OPERATED VALVESValves can be supplied with bevel gear operators• MOTOR OPERATED VALVESValves can be supplied equipped with, or prepared foractuators, either electric or pneumatic or hydraulic, of thebest types, according to customers' requirements. Thecustomer is requested to specify all information, such as themax. working differential pressure, service media, theambient temperature and humidity, electrical or air facilities,desired closing time an all other requirements that can behelpful to our engineers in choosing the more suitableactuator for the specific working conditions.• ACCESSORIESWe can supply valves fitted with other accessories such asbypasses, locking devices, chain wheels, floor stands,special extension stems and others.2


CAST STEEL GATE VALVES ANSI 150SPECIFICATIONBolted BonnetOutside Screw and YokeFlexible WedgeOval Bonnet with intergral YokeRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 14” aboveAPPLICABLE STANDARDSDesign: API 600End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598Face-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleGasket : Size 12” & below Graphite Sheet P#6633. 14” & above SingleJacket P#1650EDIMENSIONAL DATA (MM)O.D. OF RF Thk of Flange Ht. Of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 177.8 50.8 152.4 120.7 91.9 15.8 1.6 4-19.1 200 365 8.6 17.12-1/2” 190.5 63.5 177.8 139.7 104.6 17.6 1.6 4-19.1 200 398 9.7 24.53” 203.2 76.2 190.5 152.4 127.0 19.1 1.6 4-19.1 224 450 10.4 32.84” 228.6 101.6 228.6 190.5 157.2 23.9 1.6 8-19.1 250 553 11.2 45.96” 266.7 152.4 279.4 241.3 215.9 25.4 1.6 8-22.2 300 753 11.9 85.88” 292.1 203.2 342.9 298.5 269.8 28.5 1.6 8-22.2 350 950 12.7 137.610” 330.2 254.0 406.4 362.0 323.9 30.3 1.6 12-25.4 400 1165 14.2 187.012” 355.6 304.8 482.6 431.8 381.0 31.8 1.6 12-25.4 450 1370 16.0 280.014” 381.0 336.6 533.4 476.3 412.8 35.1 1.6 12-28.4 500 1520 16.8 420.016” 406.4 38704 596.9 539.8 469.9 36.6 1.6 16-28.4 600 1795 17.5 530.018” 431.8 438.2 635.0 577.9 533.4 39.7 1.6 16-31.8 600 1970 18.5 580.020” 457.2 489.0 698.5 635.0 584.2 43.0 1.6 20-31.8 680 2215 19.1 870.924” 508.0 590.6 812.8 749.3 692.2 47.8 1.6 20-35.1 760 2595 20.6 1233.830” 609.6 738.5 984.3 914.4 857.3 74.7 1.6 28-34.9 1000 3117 23.1 2508.0Non-shock pressure rating: 285 PSIG@-20 0 F to 100 0 F per ANSI B16.34PARTS AND MATERIAL LISTFIG.0112FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB03 Yoke Carbon Steel ASTM A216 Gr.WCB04 Wedge* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A108 102018 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B732 Yoke Bolt Carbon Steel A307 B33 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B35A Yoke Nut Ductile Iron A563 B35B Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102041 Set Screw Steel Steel47 Grease Nipple Steel Steel (Zn Plated)51 Packing Gland Graphite + Carbon Fiber P#6610 + #652856 Gasket* (See note*) (see Note*)73 Thrust Bearing Steel Steel*Note: Wedge : Size 16” & above A216 WCB + 13CrHeightWall Thk3


CAST STEEL GATE VALVES ANSI 300SPECIFICATIONBolted BonnetOutside Screw and YokeFlexible WedgeOval Bonnet with intergral YokeRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 14” aboveAPPLICABLE STANDARDSDesign: API 600End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598Face-to-Face Dia.of Bore O.D.of FlangePARTS AND MATERIAL LISTFIG.0312FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB03 Yoke Carbon Steel ASTM A216 Gr.WCB04 Wedge* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A108 102018 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B732 Yoke Bolt Carbon Steel A307 B33 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B35A Yoke Nut Ductile Iron A563 B35B Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102041 Set Screw Steel Steel47 Grease Nipple Steel Steel (Zn Plated)51 Packing Gland Graphite + Carbon Fiber P#6610 + #652856 Gasket* (See note*) (see Note*)73 Thrust Bearing Steel Steel*Note: Wedge : Size 2” & above Solid ,3” & above - flexibleSize 14” & above A216 Gr.WCB + 13CrGasket: 4” & below S.P.W.P#2600-E00. 6” & above S.P.W#2601-ESOØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 215.9 50.8 165.1 127.0 91.9 22.4 1.6 8-22.2 200 392 9.7 25.32-1/2” 241.3 63.5 190.5 149.4 104.6 25.4 1.6 8-22.2 200 435 11.2 43.13” 282.6 76.2 209.6 168.1 127.0 28.5 1.6 8-22.2 225 494 11.9 55.04” 304.8 101.6 254.0 200.2 157.2 31.8 1.6 8-22.2 250 592 12.7 79.46” 403.2 152.4 317.5 269.7 215.9 36.6 1.6 12-22.2 350 813 16.0 129.58” 419.1 203.2 381.0 330.2 269.7 41.2 1.6 12-25.4 400 1034 17.5 215.410” 457.2 254.0 444.5 387.4 323.9 47.8 1.6 16-28.4 450 1225 19.1 299.012” 501.7 304.8 520.7 450.9 381.0 50.8 1.6 16-31.8 500 1434 20.6 467.014” 762.0 336.6 584.2 514.4 412.8 53.9 1.6 20-31.8 600 1645 22.4 789.016” 838.2 387.4 647.7 571.5 469.9 57.2 1.6 20-35.1 600 1845 23.9 970.318” 914.4 431.8 711.2 628.7 533.4 60.5 1.6 24-35.1 680 2040 25.4 1170.020” 990.6 482.6 774.7 685.8 584.2 63.5 1.6 24-35.1 760 2310 26.9 1429.0Non-shock pressure rating: 740 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk4


CAST STEEL GATE VALVES ANSI 600SPECIFICATIONBolted BonnetOutside Screw and YokeFlexible WedgeYoke intergral with bonnetRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 8” aboveAPPLICABLE STANDARDSDesign: API 600End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0612FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB03 Yoke Carbon Steel ASTM A216 Gr.WCB04 Wedge* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A108 102018 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B35A Yoke Nut Ductile Iron A563 B35B Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102041 Set Screw Steel Steel47 Grease Nipple Steel Steel (Zn Plated)51 Packing Gland Graphite + Carbon Fiber P#6610 + #652856 Gasket* S.P.W SS304/Graphite P#2601-ESO73 Thrust Bearing Steel Steel*Note: Wedge : Size 12” & above A216 WCB + 13CrGasket : Size 16” & above Ring Joint Gasket P#1500SFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 292.1 50.8 165.1 127.0 91.9 25.4 6.4 8-19.1 200 419 11.2 36.02-1/2” 330.2 63.5 190.5 149.4 104.6 28.5 6.4 8-22.2 200 419 11.9 43.13” 355.6 76.2 209.6 168.1 127.0 31.8 6.4 8-22.2 250 520 12.7 65.04” 431.8 101.6 273.1 215.9 157.2 38.1 6.4 8-25.4 300 635 16.0 116.06” 558.8 152.4 355.6 292.1 215.9 47.8 6.4 12-28.4 450 932 19.1 217.78” 660.4 199.9 419.1 349.3 269.7 55.7 6.4 12-31.8 500 1035 25.4 410.010” 787.4 247.7 508.0 431.8 323.9 63.5 6.4 16-35.1 630 1241 28.7 660.012” 838.2 298.5 558.8 489.0 381.0 66.6 6.4 20-35.1 710 1440 31.8 943.414” 889.0 328.9 603.3 527.1 412.6 69.9 6.4 20-38.1 630 1620 35.1 1270.016” 990.6 374.7 685.8 603.3 469.9 76.2 6.4 20-41.2 710 1835 38.1 1500.0Non-shock pressure rating: 1480 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk5


CAST STEEL GATE VALVES ANSI 900SPECIFICATIONBolted BonnetOutside Screw and YokeFlexible WedgeYoke intergral with bonnetRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding Endsor Ring Joint Flanged EndsGear Operated recommended for size 4” aboveAPPLICABLE STANDARDSDesign: API 600End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0912FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB03 Yoke Carbon Steel ASTM A216 Gr.WCB04 Wedge Carbon Steel ASTM A217 CA1507 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A108 102018 Handwheel Ductile Iron A536 60-40-1821 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B35A Yoke Nut Ductile Iron A563 B35B Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102041 Set Screw Steel Steel47 Grease Nipple Steel Steel (Zn Plated)51 Packing Gland Graphite + Carbon Fiber P#6610 + #652856 Gasket Ring Joint Gasket P#1500-S73 Thrust Bearing Steel SteelFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 250 523 19.1 85.03” 381.0 72.9 241.3 190.5 127.0 38.1 6.4 8-25.4 300 620 19.1 111.04” 457.2 98.3 292.1 235.0 157.2 44.5 6.4 8-31.8 350 688 21.3 165.06” 609.6 146.1 381.0 317.5 215.9 55.7 6.4 12-31.8 500 916 26.2 394.68” 736.6 190.5 469.9 393.7 269.7 63.5 6.4 12-38.1 600 1107 31.8 594.010” 838.2 238.0 546.1 469.9 323.9 69.9 6.4 16-38.1 680 1313 36.6 865.012” 965.2 282.5 609.6 533.4 381.0 79.3 6.4 20-38.1 760 1528 42.2 960.0Non-shock pressure rating: 2220 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk6


CAST STEEL GATE VALVES ANSI 1500SPECIFICATIONBolted BonnetOutside Screw and YokeFlexible WedgeYoke intergral with bonnetRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding Endsor Ring Joint Flanged EndsGear Operated recommended for size 3” aboveAPPLICABLE STANDARDSDesign: API 600End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.1512FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB03 Yoke Carbon Steel ASTM A216 Gr.WCB04 Wedge Carbon Steel ASTM A217 CA1507 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A108 102018 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B35A Yoke Nut Ductile Iron A563 B35B Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102041 Set Screw Steel Steel47 Grease Nipple Steel Steel (Zn Plated)51 Packing Gland Graphite + Carbon Fiber P#6610 + #652856 Gasket Ring Joint Gasket P#1500-S73 Thrust Bearing Steel SteelFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 250 561 19.1 131.53” 419.1 57.2 244.3 190.5 104.6 41.2 6.4 8-28.4 300 633 22.4 172.44” 469.9 69.9 266.7 203.2 127.0 47.8 6.4 8-31.8 350 670 23.9 226.86” 546.1 92.0 311.2 241.3 157.2 53.8 6.4 8-34.9 400 759 28.7 335.66” 546.1 136.4 393.7 317.5 215.9 82.6 6.4 12-38.1 600 1048 38.1 662.08” 704.9 177.8 482.6 393.7 269.7 91.9 6.4 12-44.5 680 1246 47.8 1266.0Non-shock pressure rating: 3705 PSIG@-20 0 F to 100 0 F per ANSI B16HeightWall Thk7


CAST STEEL GLOBE VALVES• SEAT RINGSScrewed rings are bottom seated type. They are dassembled with a controlled torque setting to the body.Integral welded seat may be furnished.Both are forged or roiled in one piece, for all dimensions.They are heat treated to obtain the required surfacehardness; and are perfectly cleaned before assembling.• STEMThe stem is rolled or cut threads according to valve size;and is rolled or rectified in the packing area to assure a longlife with perfect tightness.• GLANDThe gland is made in two pieces: a cylindrical piece incontact with the packing connected through a spherical jointto the gland flange.The particular design of both pieces assures a correct loadon the packing without injuring the stem through friction orcorrosion.• STUFFING BOXThe design is to API Std.600 for high pressure class valvesand over the stuffing box is provided with a lantern ring.KVC Globe Valves are manufactured to BS1873 andAPI Std.600, and tested to API Std.598Globe Valves are used where throttling or both throttling andshut-off are required. They can also be used for on-offservice; but because of high pressure drop; this is generallyconfined to applications where the valve is normally closedand drop is not important when the valve is open.• BODY AND BONNETBody spherical form, of large radius, allows for the stresses,turbulence and resistance to flow to be kept to a minimum.Bonnets on all valves are equipped with a back seat bushing.• BODY-BONNET JOINTSBody-Bonnet Joints of globe valves are machined as follows:on 150 and 300 classes : male and female.on 600, 900 and 1500 class RTJ• DISCThe valve is normally supplied with plug type disc as shownbelow• END CONNECTIONSOur standard production covers valves with :Flanged ends (RF) that conform to ANSI B16.5 and face toface dimensions that conform to ANSI B16.10, with a raisedface serrated finish or, on request; with any other type offinish;Butt-welding ends (BW) with end to end dimensions thatconform to ANSI B16.10Customer must specify the type of schedule required; orclass of pipe; or diameter and boreRing-joint flanged ends (RTJ) that conform to ANSIB16.5, with end to end dimensions to ANSI B16.10Other special end connections are supplied to customers'special requirements.• HANDWHEELHandwheels are of a particular design, for easy operation;dimensions are according to API 600: they are made inductile iron.• GEAR OPERATED VALVESValves can be supplied with bevel gear operators.• MOTOR OPERATED VALVESValves can be supplied equipped with, or prepared foractuators, either electric or pneumatic or hydraulic, of thebest types, according to customers' requirements. Thecustomer is requested to specify all information, such asthe max working differential pressure, service media, theambient temperature and humidity, electrical or air facilities,desired closing time and all other requirements that can behelpful to our engineers in choosing the more suitableactuator for the specific working conditions.• ACCESSORIESWe can supply valves fitted with other accessories such asbypasses, locking devices, chain wheels, floor stands,special extension stems and others.8


CAST STEEL GLOBE VALVES ANSI 150SPECIFICATIONBolted BonnetOutside Screw and YokeYoke intergral with bonnetRising Stem HandwheelWelded-In/Threaded Seat Rings - StellitedFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 10” aboveAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0122FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB04 Disc* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41010 Yoke Bush Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41013 Disc Nut Carbon Steel A276 41015 Handwheel Nut Carbon Steel A536B19 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102042 Washer Carbon Steel A108 102051 Packing Graphite + Carbon Fiber P#6610 + #652856 Gasket (See Note*) (See Note*)*Note: Disc: 10” & above A217 CA15. 12” & above-A216 Gr.WCB + 13Cr.Gasket : Size 12” & below Graphite Sheet P#6633.14” & above S.P.W. P#2601-ESOFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 203.2 50.8 152.4 120.7 91.9 15.8 1.6 4-19.1 200 322 8.6 21.62-1/2” 215.9 63.5 177.8 139.7 104.6 17.6 1.6 4-19.1 200 330 9.7 23.63” 241.3 76.2 190.5 152.4 127.0 19.1 1.6 4-19.1 250 365 10.4 29.74” 292.1 101.6 228.6 190.5 157.2 23.9 1.6 8-19.1 300 424 11.2 41.66” 406.4 152.4 279.4 241.3 215.9 25.4 1.6 8-22.2 350 498 11.9 109.08” 495.3 203.2 342.9 298.5 269.7 28.5 1.6 8-22.2 450 624 12.7 187.010” 622.3 254.0 406.4 362.0 323.9 30.3 1.6 12-25.4 450 768 14.2 232.012” 698.5 304.8 482.6 431.8 381.0 31.8 1.6 12-25.4 560 785 16.0 508.0Non-shock pressure rating: 285 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk9


CAST STEEL GLOBE VALVES ANSI 300SPECIFICATIONBolted BonnetOutside Screw and YokeYoke intergral with bonnetRising Stem HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 8” aboveAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0122FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB04 Disc* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41010 Yoke Bush Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41013 Disc Nut Carbon Steel A276 41015 Handwheel Nut Carbon Steel A536B19 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102042 Washer Carbon Steel A108 102051 Packing Graphite + Carbon Fiber P#6610 + #652856 Gasket* (See Note*) (See Note*)*Note: Disc: 10” & above A217 CA15. 12” & above-A216 Gr.WCB + 13Cr.Gasket : Size 4” & below S.P.W.P#2600-EOO.6” & above S.P.W. P#2601-ESOFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 266.7 50.8 165.1 127.0 91.9 22.2 1.6 8-19.1 200 388 9.7 35.02-1/2” 292.1 63.5 190.5 149.4 104.6 25.4 1.6 8-22.2 250 400 11.2 48.53” 317.5 76.2 209.6 168.1 127.0 28.5 1.6 8-22.2 300 462 11.9 61.04” 355.6 101.6 254.0 200.2 157.2 31.8 1.6 8-22.2 350 510 12.7 71.66” 444.5 152.4 317.5 269.7 215.9 36.6 1.6 8-22.2 430 695 16.0 161.98” 558.8 203.2 381.0 330.2 269.7 41.2 1.6 12-25.4 560 800 17.5 232.010” 622.3 254.0 444.5 387.4 323.9 47.8 1.6 16-28.4 630 930 19.1 381.012” 711.2 304.8 520.7 450.9 381.0 50.8 1.6 16-31.8 630 965 20.6 664.0Non-shock pressure rating: 740 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk10


CAST STEEL GLOBE VALVES ANSI 600SPECIFICATIONBolted BonnetOutside Screw and YokeYoke intergral with bonnetRising Stem HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsGear Operated recommended for size 4” aboveAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0122FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB04 Disc* Carbon Steel ASTM A217 CA15(*see note)07 Stem Stainless Steel A276 41010 Yoke Bush Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41013 Disc Nut Carbon Steel A276 41015 Handwheel Nut Carbon Steel A536B19 Handwheel Ductile Iron A53621 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.623 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102042 Washer Carbon Steel A108 102051 Packing Graphite + Carbon Fiber P#6610 + #652856 Gasket S.P.W SS304/Graphite P#2601-ESO*Note: Disc: 6” & above A217 CA15. 8” & above-A216 Gr.WCB + 13Cr.Face-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. of RF Thk of Flange Ht. of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 292.1 50.8 165.1 127.0 91.9 25.4 6.4 8-19.1 250 392 11.2 43.53” 355.6 76.2 209.6 168.1 127.0 31.8 6.4 8-22.2 300 478 12.7 74.04” 431.8 101.6 273.1 215.9 157.2 38.1 6.4 8-25.4 350 530 16.0 107.06” 558.8 152.4 355.6 292.1 215.9 47.8 6.4 12-28.4 500 675 19.1 240.08” 660.4 199.9 419.1 349.3 269.7 55.7 6.4 12-31.8 560 721 25.4 400.010” 787.4 247.7 508.0 431.8 323.9 63.5 6.4 16-35.1 630 972 28.7 692.012” 838.2 298.5 558.8 489.0 381.0 66.6 6.4 20-35.1 710 1074 31.8 907.6Non-shock pressure rating: 1480 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk11


CAST STEEL GLOBE VALVES ANSI 900SPECIFICATIONBolted BonnetOutside Screw and YokeYoke intergral with bonnetRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsOr Ring Joint Flanged EndsGear Operated recommended for size 3” aboveAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0922FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB04 Disc Carbon Steel ASTM A217 CA1507 Stem Stainless Steel A276 41009 Yoke Sleeve Ductile Iron A439 D 2 C10 Yoke Bush Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41013 Disc Nut Carbon Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A536 B19 Handwheel * Ductile Iron A536 (*see note)29 Back Seat Ring Stainless Steel A276 41031 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102038 Guide Key Carbon Steel A108 104542 Washer Carbon Steel A108 102046 Guide Key Carbon Steel A108 104546A Hammer Blow Key Carbon Steel A108 104549 Snap Ring Carbon Steel Chrome Plated SK5 + Cr. Plated51 Packing Graphite + Carbon Fiber P#6610 + #652856 Gasket Ring Joint Gasket P#1500S73 Thrust Bearing Steel Steel76* Packing Washer(*see note) Carbon Steel A276 410B1 Hammer Blow Carbon Steel ASTM A216 Gr.WCB*Note: Handwheel : Size 6” above A216WCBItem 76: Size 6” and below Spacer: A53 Type E(SS400)Face-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. OF RF Thk of Flange Ht. Of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 350 509 19.1 120.03” 381.0 72.9 241.3 190.5 127.0 38.1 6.4 8-25.4 430 682 19.1 132.04” 457.2 98.3 292.1 235.0 157.2 44.5 6.4 8-31.8 450 738 21.3 209.06” 609.6 146.1 381.0 317.5 215.9 55.7 6.4 12-31.8 450 870 26.2 503.68” 736.6 190.5 469.9 393.7 269.7 63.5 6.4 12-38.1 750 1227 31.8 903.0Non-shock pressure rating: 2220 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk12


CAST STEEL GLOBE VALVES ANSI 1500SPECIFICATIONBolted BonnetOutside Screw and YokeYoke intergral with bonnetRising Stem Non-rising HandwheelWelded-In/Threaded Seat RingsFull PortRaised Face Flanged Ends or Buttwelding EndsOr Ring Joint Flanged EndsGear Operated recommended for size 2” aboveAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.1522FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Bonnet Carbon Steel ASTM A216 Gr.WCB04 Disc Carbon Steel ASTM A217 CA1507 Stem Stainless Steel A276 41010 Yoke Bush Ductile Iron A439 D 2 C11 Gland Flange Forged Carbon Steel A10512 Packing Gland Stainless Steel A276 41013 Disc Nut Carbon Steel A276 41014 Yoke Cap Carbon Steel A108 102015 Handwheel Nut Carbon Steel A536 B19 Handwheel * Carbon Steel ASTM A216 Gr.WCB31 Bonnet Bolt Alloy Steel A193 B733 Bonnet Nut Carbon Steel A194 2H34 Gland Bolt Carbon Steel A307 B35 Gland Nut Ductile Iron A563 B36 Hinge Pin Carbon Steel A108 102038 Guide Carbon Steel A108 104542 Washer Carbon Steel A108 102046 Guide Key Carbon Steel A108 104546A Hammer Blow Key Carbon Steel A108 104549 Snap Ring Carbon Steel Chrome Plated SK5 + Cr. Plated51 Packing Graphite + Carbon Fiber P#6610 + #652856 Gasket Ring Joint Gasket P#1500S73 Thrust Bearing Steel Steel76 Packing Washer Carbon Steel A276 410B1 Hammer Blow Carbon Steel ASTM A216 Gr.WCBFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (MM)O.D. OF RF Thk of Flange Ht. Of RFØ of BoltHolesØ ofHandwheelSizeL d D C g t f n-h O H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 350 537 19.1 131.62-1/2” 419.1 57.2 244.3 190.5 104.6 41.2 6.4 8-28.4 300 633 22.4 176.93” 469.9 69.9 266.7 203.2 127.0 47.8 6.4 8-31.8 400 615 23.9 249.44” 546.1 91.9 311.2 241.3 157.2 53.8 6.4 8-34.9 450 689 28.7 354.06” 704.9 136.4 393.7 317.5 215.9 82.6 6.4 12-38.1 600 1048 38.1 721.0Non-shock pressure rating: 2220 PSIG@-20 0 F to 100 0 F per ANSI B16.34HeightWall Thk13


CAST STEEL SWING CHECK VALVES ANSI 300KVC Swing Check Valves are manufactured to BS1868, API Std.6D and API Std.600, and tested toAPI Std.598.Swing check valves are used to prevent flow reversal in piping systems. They are suitable for service in horizontal or vertical(flow up through valve only) piping runs. Swing check valves have low pressure drop and are best suited for moderated velocityapplications.• BODYIts spherical form of large radius allow for the stresses, turbulence and resistance to flaw to be kept to a minimum.• BODY-BONNET JOINTSBody-Bonnet Joints of check valves are machined as follows:on 150 and 300 classes : male and femaleon 600, 900 and 1500 classes: RTJ• SEAT RINGSSeat rings are manufactured in two different ways, depending on the type of valves:1) Screwed seat rings, bottom seated type lapped on both sides. They are dry assembled, with a controlled torque setting to thebody.2) Welded-in seat rings, designed, in order to prevent any turbulence and avoid damages due to corrosion. Both are forged orroiled in one piece, for all dimensions. They are heat treated to obtain the requested surface hardness, and are perfectlycleaned before assembling.• END CONNECTIONSOur standard production covers valves with:Flanged ends (RF) that conform to ANSI B16.5 and face to face dimensions that conform to ANSI B16.10, with a raised faceserrated finish or, on request, with any other type of finish;Butt-welding ends (BW) with end to end dimensions that conform to ANSI B16.10 Customer mustspecify the type of schedule required, or class of pipe, or diameter and bore.Ring joint flanged ends (RTJ) that conform to ANSI B16.5, with end to end dimensions to ANSI B16.10Other special end connections are supplied to customers' special requirements.14


CAST STEEL SWING CHECK VALVES ANSI 300SPECIFICATIONBolted CoverFor Horizontal or Vertical Lines (Up Flow Only)Welded or Threaded Seat RingFull PortRaised Face Flanged Ends or Buttwelding EndsAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0132FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Cover Carbon Steel ASTM A216 Gr.WCB04 Disc * Carbon Steel ASTM A217 CA15 (*see note)16 Arm Carbon Steel ASTM A216 Gr.WCB21 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.624 Plug Bolt Carbon Steel A108 102027 Pin Stainless Steel A276 41031 Cover Bolt Alloy Steel A193 B733 Cover Nut Carbon Steel A194 2H35 Disc Nut Ductile Iron A563 B42 Washer Carbon Steel A108 102048 Eye Bolt (6” & above) Carbon Steel A108 102056 Gasket * (*See Note) (*See Note)* Note: Disc: 12” & below A217 CA15. 14” & above A216 Gr.WCB + 12CrGasket : Size 12” & below Graphite Sheet P#6633. 14” & above-S.P.W P#2601-ESODIMENSI DIMENSIONAL DATA (mm)ONAL DATA (mm) DIMENSIONAL DATA (mm) DIMENSIONAL DATA (mDIMENSIONAL DATA (mm)Face-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleO.D. OF RF Thk of Flange Ht. Of RF Ø of Bolt Holes Height Wall ThkSizeL d D C g t f n-h H a minWt (kg)2” 203.2 50.8 152.4 120.7 91.9 15.8 1.6 4-19.1 156 8.6 17.52-1/2” 215.9 63.5 177.8 139.7 104.6 17.6 1.6 4-19.1 158 9.7 21.33” 241.3 76.2 190.5 152.4 127.0 19.1 1.6 4-19.1 186 10.4 28.34” 292.1 101.6 228.6 190.5 157.2 23.9 1.6 8-19.1 218 11.2 50.06” 355.6 152.4 279.4 241.3 215.9 25.4 1.6 8-22.4 240 11.9 70.08 495.3 203.2 342.9 298.5 269.7 28.5 1.6 8-22.4 279 12.7 148.810 622.3 254.0 406.4 362.0 323.9 30.3 1.6 12-25.4 315 14.2 222.012 698.5 304.8 482.6 431.8 381.0 31.8 1.6 12-25.4 355 16.0 318.414 787.4 336.6 533.4 476.3 412.8 35.1 1.6 12-28.4 376 16.8 442.716 863.6 387.4 596.9 539.8 469.9 36.6 1.6 16-28.4 402 17.5 573.018 977.9 438.2 635.0 577.9 533.4 39.7 1.6 16-31.8 512 18.3 710.020 977.9 489.0 698.5 635.0 584.2 43.0 1.6 20-31.8 597 19.1 892.024 1295.4 590.6 812.8 749.3 692.2 47.8 1.6 20-35.1 651 20.6 1576.0Non-shock pressure rating: 285 PSIG@-20 0 F to 100 0 F per ANSI B16.3415


CAST STEEL SWING CHECK VALVES ANSI 300SPECIFICATIONBolted CoverFor Horizontal or Vertical Lines (Up Flow Only)Welded or Threaded Seat RingFull PortRaised Face Flanged Ends or Buttwelding EndsAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0132FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Cover Carbon Steel ASTM A216 Gr.WCB04 Disc * Carbon Steel ASTM A217 CA15 (*see note)16 Arm Carbon Steel ASTM A216 Gr.WCB21 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.624 Plug Bolt Carbon Steel A108 102027 Pin Stainless Steel A276 41031 Cover Bolt Alloy Steel A193 B733 Cover Nut Carbon Steel A194 2H35 Disc Nut Ductile Iron A563 B42 Washer Carbon Steel A108 102048 Eye Bolt (6” & above) Carbon Steel A108 102056 Gasket * (*See Note) (*See Note)* Note: Disc: 12” & below A217 CA15. 14” & above A216 Gr.WCB + 13CrGasket : Size 4” & below S.P.W.P#2600. 6” & above-S.P.W P#2601-ESOFace-to-Face Dia.of Bore O.D.of FlangeDIMENSIONAL DATA (mm)Ø of BoltCircleO.D. OFRFThk of FlangeHt. Of RFSizeL d D C g t f n-h H a minWt (kg)2” 266.7 50.8 165.1 127.0 91.9 22.2 1.6 8-19.1 172 9.7 25.42-1/2” 292.1 63.5 190.5 149.4 104.6 25.4 1.6 8-22.2 194 11.2 34.03” 317.5 76.2 209.6 168.1 127.0 28.5 1.6 8-22.2 213 11.9 39.04” 355.6 101.6 254.0 200.2 157.2 31.8 1.6 8-22.2 251 12.7 63.06” 444.5 152.4 317.5 269.7 215.9 36.6 1.6 8-22.2 285 16.0 106.08” 533.4 203.2 381.0 330.2 269.7 41.2 1.6 12-25.4 330 17.5 184.010” 622.3 254.0 444.5 387.4 323.9 47.8 1.6 16-28.4 360 19.1 275.812” 711.2 304.8 520.7 450.9 381.0 50.8 1.6 16-31.8 390 20.6 441.014” 838.2 336.6 584.2 514.4 412.8 53.9 1.6 20-31.8 423 22.4 721.016” 663.5 387.4 647.7 571.5 469.9 57.2 1.6 20-35.1 460 23.9 902.618” 977.9 431.8 711.2 628.7 533.4 60.5 1.6 24-35.1 550 25.4 1002.420” 1018.0 482.6 774.7 665.8 584.2 63.5 1.6 24-35.1 650 28.9 1183.024” 1346.2 564.2 914.4 812.6 692.2 69.9 1.6 24-41.2 820 30.2 1941.0Non-shock pressure rating: 740 PSIG@-20 0 F to 100 0 F per ANSI B16.34Ø of BoltHolesHeightWall Thk16


CAST STEEL SWING CHECK VALVES ANSI 600SPECIFICATIONBolted CoverFor Horizontal or Vertical Lines (Up Flow Only)Welded or Threaded Seat RingFull PortRaised Face Flanged Ends or Buttwelding EndsAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0132FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Cover Carbon Steel ASTM A216 Gr.WCB04 Disc * Carbon Steel ASTM A217 CA15 (*see note)16 Arm Carbon Steel ASTM A216 Gr.WCB21 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.624 Plug Bolt Carbon Steel A108 102027 Pin Stainless Steel A276 41031 Cover Bolt Alloy Steel A193 B733 Cover Nut Carbon Steel A194 2H35 Disc nut Ductile Iron A563 B42 Washer Carbon Steel A108 102048 Eye Bolt (4” & above) Carbon Steel A108 102056 Gasket S.P.W SS304/Graphite P#2601-ESO* Note: Disc: 12” & below A217 CA15. 14” & above A216 Gr.WCB + 13CrFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (mm)O.D. OFRFThk of FlangeHt. Of RFSizeL d D C g t f n-h H a minWt (kg)2” 292.1 50.8 165.1 127.0 91.9 25.4 6.4 8-19.1 187 11.2 35.33” 355.6 76.2 209.6 168.1 127.0 31.8 6.4 8-22.2 210 12.7 66.74” 431.8 101.6 273.1 215.9 157.2 38.1 6.4 8-25.4 256 16.0 111.06” 558.8 152.4 355.6 292.1 215.9 47.8 6.4 12-28.4 329 19.1 220.08” 660.4 199.9 419.1 349.3 269.7 55.7 6.4 12-31.8 363 25.4 385.010” 787.4 247.7 508.0 431.8 323.9 63.5 6.4 16-35.1 464 28.7 600.012” 838.2 298.5 558.8 489.0 381.0 66.6 6.4 20-35.1 486 31.8 780.014” 889.0 326.9 603.3 527.1 412.8 69.9 6.4 20-38.1 572 35.1 1364.016” 990.6 374.7 685.8 603.3 469.8 76.2 6.4 20-41.2 680 38.1 1769.0Non-shock pressure rating: 1480 PSIG@-20 0 F to 100 0 F per ANSI B16.34Ø of BoltHolesHeightWall Thk17


CAST STEEL SWING CHECK VALVES ANSI 900SPECIFICATIONBolted CoverFor Horizontal or Vertical Lines (Up Flow Only)Welded or Threaded Seat RingFull PortRaised Face Flanged Ends or Buttwelding EndsOr Ring Joint Flanged EndsAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.0932FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Cover Carbon Steel ASTM A216 Gr.WCB04 Disc Carbon Steel ASTM A217 CA1516 Arm Carbon Steel ASTM A216 Gr.WCB21 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.624 Plug Bolt Carbon Steel A108 102025 Plug Gasket Graphite + Carbon Fibre P#661027 Pin Stainless Steel A276 41031 Cover Bolt Alloy Steel A193 B733 Cover Nut Carbon Steel A194 2H35 Disc nut Ductile Iron A563 B42 Washer Carbon Steel A108 102042A Plug Washer Carbon Steel A108 102048 Eye Bolt (4” & above) Carbon Steel A108 102056 Gasket S.P.W SS304/Graphite P#1500SFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (mm)O.D. OFRFThk of FlangeHt. Of RFSizeL d D C g t f n-h H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 223 19.1 78.03” 381.0 72.9 241.3 190.5 127.0 38.1 6.4 8-25.4 255 19.1 88.54” 457.2 98.3 292.1 235.0 157.2 44.5 6.4 8-31.8 295 21.3 181.46” 609.6 146.1 381.0 317.5 215.9 55.7 6.4 12-31.8 345 26.2 313.08” 736.6 190.5 469.9 393.7 269.7 63.5 6.4 12-38.1 415 31.8 467.010” 836.2 236.0 546.1 469.0 323.9 69.9 6.4 18-38.1 550 36.6 1150.0Non-shock pressure rating: 2220 PSIG@-20 0 F to 100 0 F per ANSI B16.34Ø of BoltHolesHeightWall Thk18


CAST STEEL SWING CHECK VALVES ANSI 1500SPECIFICATIONBolted CoverFor Horizontal or Vertical Lines (Up Flow Only)Welded or Threaded Seat RingFull PortRaised Face Flanged Ends or Buttwelding EndsOr Ring Joint EndsAPPLICABLE STANDARDSDesign: ANSI B16.34End Flange : ANSI B16.5Weld Ends : ANSI B16.25Face-to-Face: ANSI B16.10Shell and Seat Test: API 598PARTS AND MATERIAL LISTFIG.1532FNo. Part Name Material ASTM Specification01 Body Carbon Steel ASTM A216 Gr.WCB02 Cover Carbon Steel ASTM A216 Gr.WCB04 Disc Carbon Steel ASTM A217 CA1516 Arm Carbon Steel ASTM A216 Gr.WCB21 Body Seat Ring Carbon Steel + Stellite No.6 A105 + Stellite No.624 Plug Bolt Carbon Steel A108 102025 Plug Gasket Graphite + Carbon Fibre P#661027 Pin Stainless Steel A276 41031 Cover Bolt Alloy Steel A193 B733 Cover Nut Carbon Steel A194 2H35 Disc nut Ductile Iron A563 B42 Washer Carbon Steel A108 102042A Plug Washer Carbon Steel A108 102048 Eye Bolt (6” & above) Carbon Steel A108 102056 Gasket Ring Joint Gasket P#1500SFace-to-Face Dia.of Bore O.D.of FlangeØ of BoltCircleDIMENSIONAL DATA (mm)O.D. OFRFThk of FlangeHt. Of RFSizeL d D C g t f n-h H a minWt (kg)2” 368.3 47.5 215.9 165.1 91.9 38.1 6.4 8-25.4 223 19.1 122.42-1/2” 419.1 57.2 244.3 190.5 104.6 41.2 6.4 8-28.4 265 22.4 167.83” 469.9 69.9 266.7 203.2 127.0 47.8 6.4 8-31.8 325 23.9 195.04” 546.1 91.9 311.2 241.3 157.2 53.8 6.4 8-34.9 350 28.7 290.36” 704.9 136.4 393.7 317.5 215.9 82.6 6.4 12-38.1 370 38.1 430.98” 831.9 177.8 482.6 393.7 269.7 91.9 6.4 12-44.5 405 47.8 675.810” 990.6 222.3 584.2 482.6 323.9 108.0 6.4 12-50.8 435 57.2 1850.0Non-shock pressure rating: 3705 PSIG@-20 0 F to 100 0 F per ANSI B16.34Ø of BoltHolesHeightWall Thk19


WELDING END DETAILSELECTRICALLY OPERATED VALVESFor production of an electrically operated valve (motoroperated valve), specifications such as listed below arerequired :1. Type or model number of motor.2. Type of construction : water-proof or explosion-proof3. Type of manual operating device.4. Open/close operating device.5. Power source.(for motor; voltage, Hz, 3-phase)(for control; voltage, Hz, single-phase)A. Type of valve.B. Primary fluid pressure: kg f/cm 2 max.C. Differential pressure of a closed valve : kg f/cm 2 max.D. Fluid temperature: ° C max.E. Atmospheric temperature: ° C max.GEAR OPERATED VALVESFor production of a gear operated valve, specificationssuch as listed below are required :1. Size and figure number of valve.2. Service media, Pressure and Temperature.3. Max. pressure against which valve must close.4. Any handwheel torque or rim-pull limitation.5. Limitations, if any on the type or brand of actuator.6. Other20


WELDING END DETAILSCOMPOUND BEVELConnection Pipe Wall ThicknessLarger than 7/8” sizePLAIN BEVELConnection Pipe Wall Thickness7/8” ans smaller sizeABC= Outside diameter of matching pipe, wrought or fabricated component= Nominal inside diameter= Min. wall thickness“A” Dimensions reference to ANSI B16.25“B” Dimensions reference to ANSI B36.10Valve mm 15 20 25 40 50 65 80 100 150 200 250 300 350 400 450 500 600nominalsize in 1/2 3/4 1 1-1/2 2 2-1/2 3 4 6 8 10 12 14 16 18 20 24Tolerenceon A(mm)Tolerenceon B(mm)+0-0.8±0.8 ±1.6±3.2-1.621


REFERENCE STANDARDS AND SPECIFICATIONRING JOINT CONNECTION BETWEEN BODY AND BONNET/COVERGATE VALVESCLASS 900 CLASS 1500SIZEP E F RING No P E F Ring No2” 136.5 7.9 11.9 R35 136.5 7.9 11.9 R352-1/2” 161.9 7.9 11.9 R39 161.9 7.9 11.9 R393” 149.2 7.9 11.9 R37 161.9 7.9 11.9 R394” 211.1 7.9 11.9 R45 193.7 7.9 11.9 R446” 235.0 7.9 11.9 R99 269.9 11.1 16.7 R508” 323.9 7.9 11.9 R53 381.0 14.3 23.0 R5810” - - - - - - - -12” - - - - - - - -14” - - - - - - - -16” - - - - - - - -GATE VALVESSIZECLASS 900 CLASS 1500P E F RING No P E F Ring No2” 117.5 7.9 11.9 R30 117.5 7.9 11.9 R303” 136.5 7.9 11.9 R35 161.9 7.9 11.9 R394” 193.7 7.9 11.9 R44 193.7 7.9 11.9 R446” 269.9 7.9 11.9 R49 269.9 11.1 16.7 R508” 323.9 7.9 11.9 R53 - - - -10” - - - - - - - -12” - - - - - - - -SWING CHECK VALVESCLASS 900 CLASS 1500SIZEP E F RING No P E F Ring No2” 11.7.5 7.9 11.9 R30 117.5 7.9 11.9 R303” 136.5 7.9 11.9 R41 136.5 7.9 11.9 R354” 181.0 7.9 11.9 R41 136.5 7.9 11.9 R356” 269.9 7.9 11.9 R49 193.7 7.9 11.9 R448” 323.7 7.9 11.9 R53 269.9 11.1 16.7 R5010” - - - - 323.8 11.1 16.7 R5412” - - - - - - - -22


REFERENCE STANDARDS AND SPECIFICATIONKVC ®valves are offered to meet the following Codes and Standards : Valves to BS StandardDIN Standard as well as GOST Standard are available upon request.• ANSI STANDARDS - AMERICAN NATIONAL STANDARDS INSTITUTEB1.1 Unified Screw Threads Acme Screw ThreadsB1.5 Acme Screw ThreadsB1.8 Stub Acme Screw ThreadsB1.12 Class 5 Interference - Fit ThreadB2.1 Pipe Threads (Except Dryseal)B16.5 Steel Pipe Flanges, and Flanged FittingsB16.10 Face-to-Face and End-to-End Dimensions of Ferrous ValvesB16.11 Forged Steel Fittings, Socket Welding and ThreadedB16.20 Ring-Joint Gaskets and Grooves for Steel Pipe FlangesB16.21 Non-metallic Gaskets for Pipe FlangesB16.25 Buttwelding EndsB16.34 Steel ValvesB18.2.2 Square and Hex NutsB31.1.0 Power PipingB31.2 Fuel Gas PipingB31.3 Petroleum Refinery PipingB31.4 Liquid Petroleum Transportation Piping Systems RefrigerationB31.5 Refrigeration Piping SystemsB31.6 Chemical Process PipingB31.7 Nuclear Power PipingB31.8 Gas Transmission and Distribution Piping SystemsB36.10 Wrought-Steel and Wrought-Iron Pipe• API STANDARDS - AMERICAN PETROLEUM INSTITUTE6ASpecification for Wellhead Equipment6DSpecification for Pipeline Valves597 Steel Venturi Gate Valves598 Valve Inspection and Test600 Steel Gate Valves, Flanged or Buttwelding Ends603 150-Lb, Light-Wall, Corrosion-Resistant Gate Valve for Refinery Use605 Large Diameter Carbon Steel Flanges• ASTM STANDARDS - AMERICAN SOCIETY FOR TESTING AND MATERIALS• MSS STANDARD PRACTICES - MANUFACTURERS STANDARISATION SOCIETY OF THE VALVEAND FITTINGS INDUSTRYSP-6 Finishes-for Contract Faces of Connection End Flanoes of Ferrous Valves and FittingsSP-9 MSS Spot-Facing StandardSP-25 MSS Standard Making System for Valves, Fittings, Flanges and UnionsSP-42 MSS 150Lb Corrosion Resistant Cast Flanged ValvesSP-44 MSS Steel Pipe Line FlangesSP-45 MSS Bypass and Drain Connection StandardSP-53 Quality Standard for Steel Castings, Dry Particle Magnetic Inspection MethodSP-54 Quality Standard for Steel Castings, Radiographic Inspection MethodSP-55 Quality Standard for Steel Castings, Visual MethodSP-61 Hydrostatic Testing of Steel Valves23


COMPARISON LIST FOR CASTING AND FORGINGSGENERALCASTINGFORGINGSCLASSIFICATION ASTM JIS BS ASTM JIS BSA126 - Class A G5501 -FC20 1452 -14 - - -Cast Iron- Class B -FC25 -17 - - -- Class C -FC30 -20 - - -A197 -FMCB28 310 -B18/6 - - -Malleable Iron447 -32510 -FMCB35 -B22/14 - - --35018 -FMCB37 - - - -A395 G5502 -FCD40 - - - -Ductile Iron- G5502 -FCD45 - - - -A536 -FCD55 - - - -A216 -WCA G5151 -SCPH1 - A105 G3201 - SF45 1503 - 161B- G5101 -SC46 1504 - 161 - - -Carbon SteelA216 -WCB G5151 -SCPH2 -B A105 G3201 - SF50 1503 - 161C-WCC - - - - -- G5101 -SC55 -C - - -Carbon-1/2Mo A217 -WC1 G5111 -SCA41 1504 - 240 A182 - F1 - 1503 - 240B1/2Cr-1/2Mo-1/2Ni -WC4 - - - - -1Cr-1/2Mo-1/2Ni -WC5 - - -F12 - 1503 - 6021.1/4Cr-1/2Mo -WC6 G5111 -SCA51 1504 - 621 -F11 - -2.1/4Cr-1Mo -WC9 - -622 -F22 - 1503 - 6223Cr-Mo - - - -F21 - -5Cr-1/2Mo(C 0.15) - - - -F5 - -5Cr-1/2Mo(C 0.25) A217 -C5 G5111 -SCA52 1504 -625 -F5a - 1503 - 6257Cr-1/2Mo - - - -F7 - -9Cr-1Mo A217 -C12 - 1504 -629 -F9 - -Carbon Steel for Low Temp. A352 -LCB - 4242 -GRA A350 - LF1 - -Carbon-Si - - - -LF2 - -Carbon 1Mo for Low Temp. A351 -LC1 - - - - -2.1/2Ni -LC2 - - - - -3.1/2Ni -LC3 - - A350 - LF3 - -Cr-Ni-Cu-Al - - - - LF4 - -13Cr A217 -CA15 G5121 -SCS1 - A182 -F6 G4303-SUS51B 1503 - 71318Cr-8Ni(C 0.03) A351 -CF3 - - -F304L -SUS28B -18Cr-8Ni(C 0.08) -CF8 G5121 -SCS13 - -F304 -SUS27B 1503 - 80118Cr-8Ni(C 0.10) - - 1504 -801 -F304H - -18Cr-8Ni-2Mo(C 0.03) A351 -CF3M G5121 -SCS16 - -F316L G4303-SUS33B -18Cr-8Ni-2Mo(C 0.08) -CF8M -SCS14 1632 -GRC -F316L -SUS32B 1503 - 845B18Cr-8Ni-2Mo(C 0.10) - - - -316H - -18Cr-8Ni-Ti(C 0.08) - - - -F321 G4303-SUS29B -18Cr-8Ni-Ti(C 0.10) - - 1504 -821Ti - -F321H 1503 - 821Ti18Cr-8Ni-Cb(C 0.08) A351 -CF8C - - -F347 G4303-SUS43B - 821Nb18Cr-8Ni-Cb(C 0.10) - - 1504 -821Nb -F347H - -18Cr-8Ni-Ta-Cb(C 0.08) - - - -F348 - -18Cr-8Ni-Ta-Cb(C 0.10) - - - -F348H - -25Cr-20Ni(C 0.15) - - - -F310 - -22Cr-12Ni(C 0.08) A351 -CH18 - - - - -22Cr-12Ni(C 0.10) -CH10 - - - - -22Cr-12Ni(C 0.20) -CH20 - - - - -23Cr-19Ni(C 0.20) -CK20 - - - - -23Cr-19Ni(C 0.35) -HK30 - - - - -23Cr-19Ni(C 0.45) -HK40 - - - - -13Cr-33Ni-Mo(C 0.35) -HT30 - - - - -15Cr-13Ni-2Mo-Cb(C 0.10) CF10MC - - - - -19Cr-27Ni-2Mo-3Cu(C 0.07) -CN7M - - - - -8Cr-20Ni(C 0.20) - - - A182 - F10 - -HASTELLOY.B A494 -N- 12MV - - - - -24


CHEMICAL AND PHYSICAL PROPERTIESCASTING MATERIALSCarbonSteelCA-15HighTempHighTempCHEMICAL PROPERTIES304-S.S 316-S.S Hastelloy-B 304L-S.S. 316L-S.SLow-TempHigh TempASTM Std A-216 A-217 A-217 A-217 A-351 A-351 A-494 A-351 A-351 A352 A-217 A-217Grade WCB CA-15 WC6 WC9 CF8 CF8M N-12MV CF3 CF3M LCB C-5 C-12C% Max. 0.30 0.15 0.20 0.18 0.08 0.08 0.12 0.03 0.03 0.30 0.20 0.20Mn% 1.00Max. 1.00 0.50-0.80 0.40-0.70 1.50 1.50 1.00 1.50 1.50 1.00 0.40-0.70 0.35-0.65P% Max. 0.04 0.04 0.04 0.04 0.04 0.04 0.040 0.04 0.04 0.04 0.04 0.04S% Max. 0.045 0.045 0.045 0.045 0.04 0.04 0.030 0.04 0.04 0.045 0.045 0.045Ni% 0.50 Max. 1.00 - - 8.00-11.00 9.00-12.00 Bal 8.00-12.00 9.00-13.0 - - -Cr% 0.50 Max. 11.5-14.0 1.00-1.50 2.00-2.75 18.0-21.0 18.0-21.0 1.00 17.0-21.0 17.0-21.0 - 4.0-6.50 8.00-10.00Mo% 0.20 Max. - 0.45-0.65 0.90-1.20 - - 26.0-30.0 0.50 Max. 0.50 Max. - 0.45-0.65 0.90-1.20Cu 0.30 Max. - - - - - - - - - - -Si 0.60 Max. 1.50 0.60 0.60 2.00 1.50 1.00 2.00 1.50 0.60 0.75 1.00Fe - - - - - - 4.0-6.0 - - - - -V - - - - - - 0.20-0.60 - - - - -PHYSICAL PROPERTIESTensilestrengthMin. KisMpaYield PointMin-KisMpaElongationin 2 inch(50mm)%Min.Reductionof area% Min70-95485-6553625090-115620-7956545070-95485-6554027570-95485-655402757048530205704853020576525402757048530205704853020565-95450-6203524090-115620-79522 18 20 20 35 30 6 35 30 24 18 1835 30 35 35 - - - - - 35 35 356041590-115620-79360415WROUGHT MATERIALS11-13%CrDuctileCarbonSteelCHEMICAL PROPERTIESB-8F 321-S.S. 304-S.S. 316-S.S. 304L-S.S 316-S.S.ASTM Std A-182 A-439 ASTM A-320 A-182 A-182 A-182 A-182 A-182 KLS A-193 A-194Grade F6a D,C A-105 B-8F F-321 F-321 F-316 F-304L F-316L HF-6R B7 2HC% Max. 0.15 0.29 -0.35 Max. 0.15 0.08 0.08 0.08 0.08 0.08 1.05 0.37-0.49 0.40S1% 1.00 1.00-3.00 0.35 1.00 1.00 1.00 1.00 1.00 1.00 1.11 0.15-0.35 -Mn% Max. 1.00 1.80-2.4 0.60-1.05 2.00 2.00 2.00 2.00 2.00 2.00 - 0.75-1.20 -P% Max. 0.04 0.08 0.04 0.20 0.04 0.04 0.04 0.04 0.04 - 0.035 0.04S% 0.03 - 0.05 0.15-0.35 0.03 0.03 0.03 0.03 0.03 - 0.04 0.05Ni% 0.50 Max. 21.0-24.0 - 8.00-10.00 9.00-12.00 8.0-11.0 10.0-14.0 8.00-13.00 10.00-15.00 - - -Cr% 11.5-13.5 0.50 - 7.00-19.00 17.00Min 18.0-20.0 16.0-18.0 18.00-20.00 16.00-18.00 28.30 0.75-1.20 -Mo% - - - - - - 2.00-3.00 - 2.00-3.00 - 0.15-0.25 -Ti% - - - - C%X5-0.7 - - - - - - -Fe% Bal. - - - - - - - - 0.30 Bal. Bal.W% - - - - - - - - - 4.20 - -Co% - - - - - - - - - Bal. - -PHYSICAL PROPERTIESTensilestrengthMin. KisMpaYield PointMin-KisMpaElongationin 2 inch(50mm)%Min.Reductionof area% Min855865537958400281937048336248755173020775517302077551730207755177048370483HardFacing18 20 22 35 30 30 30 30 30 - 16 -35 - 30 50 50 50 50 50 50 - 50 -302072517225172--Bolts125862105724Nuts175-25


GASKET SPECIFICATION & CONSTRUCTIONPERFORMANCE CONSTRUCTION & FEATURES MAIN APPLICATIONTemp: 752°F (400°C)Pressure :740 PSI (52kfg/cm 2 )Graphite is highly pliable,making matching contactwith the whole of the flange surface, to giveexcellent sealing capabilities under low seatingstress. Graphite is made of pure graphite andmaintains its chemical-resistant properties. Thepure graphite in Graphite is very little affected bylow temperatures and can be used in cryogenicequipment. Its performance is not affected byheating.Water, sea water, hot water, steam, air,acids, alkalism aqueous salt solutions,animal and vegetable oils, alcohols, fueloils, hydraulic fluids, lubricatiing oil, aliphaticsolvents and their vapors, various gasesand liquefied gases.Temp: -150°F ~300°F(100°C -- 150°C)Press: 285PSI (20kgf/cm Z )An enveloped type gasket made by lining a 1 mmthick teflon disk and inserting a core insideStrong acids, strong alkalis, oxygen,chlorine gas, and organic solvents.Temp: 1,100°F (600°C)Press: 6,000 PSI (425 kg f/cm Z )A spiral wound gasket made by alternatelywinding the metal hoops formed to a V shape andthe asbestos sheets subjected to impermeabilitytreatment. Featuring excellent gas sealability,heatresistance and elasticity, this Standard Materials.Hoop ................. SUS304Filler ......... Asbestos sheetInner ring ............... SPCCOuter ring .............. SPCCWater, steam, oils, oil gas, gases and solvents.Temp: 1,100°F (600°C)Press: 6,000 PSI (425 kg f/cm 2 )This is an entirely new type of spiral woundgasket using teflon soft tapes of 100% PTFEhaving resilence and elasticity for the fillermaterial it has superior gas sealability chemicalresistance and other property advantages and isusable for virtually any kind of fluids. StandardMaterialsHoop ................. SUS304Filler............... Soft teflonInner ring ........... SUS304Outer ring ........... SUS304General chemicals, corrosive fluids, gases anddangerous fluids.Temp: 1,600°F (870°C)Press: 6,000 PSI (425 kg f/cm 2 )A spiral wound gasket using grafoil tapes for fillermaterial, and featuring excellent gas sealability,heat resistance and chemical resistance. Thisprovides the highest level of performances amongall the existing gaskets. Standard MaterialsHoop ................. SUS304Filler ............ raphoil tapesInner ring ............... SPCCOuter ring .............. SPCCSteam of high temperatures and high pressures,dangerous gases. He gas, ammonia and LNG.Depends on metal materials.Flat-shaped metallic gasket which an asbestosmill board is jacketed with a single ply of metalsheet.Steam of high temperatures and high pressures,gases, oil gas, solvent vapors, pipe flange, solventvapors, and covers of pressure vessels.Depends on metal materials.Flat-shaped metallic gasket which an asbestosmill board with a metal sheet in doublePipe flanges and heat exchangers of petroleumrefining industry and petrochemical industry.Depends on metal materials.Metallic gasket made by fabricating a metalwaveforms to enable more contact face pressureto be taken, and adding the spring effect toimprove sealability.Bonnets of various valves for steam of hightemperatures and low pressures, oil, gas, solventvapors and heat medium oil.Depends on metal materials.Metallic gasket made by machining concentricallysharp V-grooves of 60° or 90° to a flat metalgasket at roughly 1 mm pitch.Pipe flanges and valve bonnets for steam of hightemperatures and high pressures, and gases.Depends on metal materials.Metallic ring joint by machining various metalmaterials to an octagonal shape.High-temperature high--pressure pipe flanges,valve bonnets and heat exchangers.Depends on metal materials.Metallic ring joint gasket made by machiningvarious metal materials into an oval section.High-temperature high pressure pipe flanges,valve bonnets and heat exchangers.26


GASKET SPECIFICATION & CONSTRUCTIONNAMEMAKERSCrane Jeil Pillar Tombo ValqueCROSS SECTIONGraphite Sheet- - 6633 1215 VF352Lip Type Envelopedgasket11-C - 4430 9010A 7030911 1804 2200 1804 590Spiral Wound Gasket- 3804-TF 2300 9090 7590- 3804-SF 2600 1804GR 6590VSingle Metal JacketedGasket 923 1840 1000 1840 580Double Metal JacketedGasket- 1841 1004 1840 580Corrugated Gasket SoftIron900 1870 1200 1880 500Serrated Gasket Metal 941 - 1300 1850-S 540Octagonal Ring JointGasket954 - 1500 1850-L 550SZOval Ring Joint Gasket - - 1501 1850V 5500Z27


GASKET SPECIFICATION & CONSTRUCTIONCONSTRUCTION &FEATURESPERFORMANCEMAINAPPLICATIONSChesertonMAKERSJohnPillarCranePalmettoRound Braided AsbestosImpregnated with High Temp.Lubricant & GraphilaTEMP: 660: 660 ° F (350°)PRESS: 570 PSI (40kgf/cm 2 )Water, saturated steamgeneral purpose valves 510310815 114 -Braided AsbestosAsbestos with Inconel WireBraided around aResilent Asbestos CoreTEMP: 1200° F (650°)PRESS: 6000 PSI (425kgf/cm 2 )Saturated stem, hot oils,petroleum-baseammonia, valves, cocks10001500C-10681871316 4062Braided Asbestos, TFELubricationInterlaced Braided Asbestoswith TFE SuspensionTEMP: -330° F - 500° F(-200° C - 260° C)PRESS: 2840 PSI (200kgf/cm 2 )PH : 2 ~ 3Solvents, acids, alkalis,oxygen and LNG. 3221722C06451345331347HJinterlaced BraidedSpecially Lubricated TFEMultifilament Yarn withTFE DispersionTEMP: -150° F - 500° F(-100° C - 260° C)PRESS: 1420 PSI (100kgf/cm 2 )PH : 0 ~ 14Solvents, strong acids,strong alkalis, fluidswhich does not allowpollution.1728328C1050 4505L 1367SInterlaced BraidedTFE Multifilament Yarnwith TFE SuspensionTEMP: -330° F - 500° F(-200° C - 260° C)PRESS: 2840 PSI (200kgf/cm 2 )PH : 0 ~14Solvents strong acids,strong alkalis, and fluidswhich does not allowpollution.3241724C1045 4525 1367HGraphoilGraphoil flexible GraphiteContaining No Binders,Lubricants or Other AdditivesTEMP: -1200° F (650° C)PRESS: 6000 PSI (425kgf/cm 2 )PH : 0 ~ 14Water, steam oils, oilgases,solvents, heattranser oil, LNG strongacids and strongalkalis.GTP 229C 6610 -Non-Asbestos WireInserted core of ChoppedGlass Fiber with Jacket ofWire Inserted Glass YarnGraphited OutsideTEMP: -1200° F (650° C)PRESS: 6000 PSI (425kgf/cm 2 )PH : 2 ~12For air, water, steam, oilliquid petroleum,chemical,corrosive and similarservices.1200 2871 6711 -TFE Impregnated syntexasbestos-free yarnwith high temperature breakinlube. Inter woven TM braid,Non-ContaminatingTEMP: 450° F (232° C)PRESS : 1500 PSI(105.5kgf/cm 2 )Mild acids, Caustics,Solvents, Steam, Oils,neutral fluids. - - - 1347AFLattice braided, 100%graphite filament packingimpregnated with specialLubricantTEMP: -420° F - 932° F(-250° C - 500° C)PRESS: 6250 PSI (440kgf/cm 2 )PH : 0 ~ 14Water, Steam, Oil,Solvent,Heat transfer oil, Gas,LNG,Strong acid, strongalkalis.- - 6528 -28


PRESSURE TEMPERATURE RATINGSSERVICETEMPERATURE°F °C WCB(a)WC1(b) (cCLASS 150 CLASS 300 CLASS 600WC6(c )WC9(c )C5(c )WCB(a)WC1(b) (c)-20 to -29 to 285 265 290 290 290 740 695 750 750 750 1480 1390 1500 1500 1500100 38200 93 260 260 260 260 260 675 680 710 715 750 1350 1360 1425 1430 1500300 149 230 230 230 230 230 655 655 675 675 730 1315 1305 1345 1355 1455400 204 200 200 200 200 200 635 640 660 650 705 1270 1280 1315 1295 1410500 260 170 170 170 170 170 600 620 640 640 665 1200 1245 1285 1280 1330600 316 140 140 140 140 140 550 605 605 605 605 1095 1210 1210 1210 1210650 343 125 125 125 125 125 535 590 590 590 590 1075 1175 1175 1175 1175700 371 110 110 110 110 110 535 570 570 570 570 1065 1135 1135 1135 1135750 399 95 95 95 95 95 505 530 530 530 530 1010 1065 1065 1065 1065800 427 80 80 80 80 80 410 510 510 510 500 825 1015 1015 1015 995850 454 65 65 65 65 65 270 485 485 485 440 535 975 975 975 880900 482 50 50 50 50 50 170 450 450 450 355 345 900 900 900 705950 510 35 35 35 35 35 105 280 380 380 260 205 560 755 755 5201000 538 20 20 20 20 20 50 165 225 270 190 105 330 445 535 3851050 566 20* 20* 20* 140 200 140 275 400 2801100 593 20* 20* 20* 95 115 105 190 225 2051150 621 20* 70 1401200 649 20* 45 90Hydrostatic ShellTest Pressure450 400 450 1125 1050 1125 2225 2100 2250ValveClosureFluid 315 292 319 814 765 815 1630 1529 1650TestPressureGas 80 80 80WC6(c )WC9(c )C5(c )WCB(a)WC1(b) (c)WC6(c )WC9(c )C5(c )SERVICETEMPERATURE°F °C WCB(a)WC1(b) (c)CLASS 900 CLASS 1500 CLASS 2500WC6(c)WC9(c)C5(c)WCB(a)WC1(b) (c)-20 to -29 to 2220 2285 2250 2250 2250 3705 3470 3750 3750 3750 6170 5785 6250 6250 6250100 38200 93 2025 2035 2135 2150 2250 3375 3395 3560 3580 3750 5625 5660 5930 5965 6250300 149 1970 1955 2020 2030 2185 3280 3260 3365 3385 3640 5470 5435 5605 5640 6070400 204 1900 1920 1975 1945 2115 3170 3200 3290 3240 3530 5280 5330 5485 5400 5880500 260 1795 1865 1925 1920 1995 2995 3105 3210 3200 3325 4990 5180 5350 5330 5540600 316 1640 1815 1815 1815 1815 2735 3025 3025 3025 3025 4560 5040 5040 5040 5040650 343 1610 1765 1765 1765 1765 2685 2940 2940 2940 2940 4475 4905 4905 4905 4905700 371 1600 1705 1705 1705 1705 2665 2840 2840 2840 2840 4440 4730 4730 4730 4730750 399 1510 1595 1595 1595 1595 2520 2660 2660 2660 2660 4200 4430 4430 4430 4430800 427 1235 1525 1525 1525 1490 2060 2540 2540 2540 2485 3430 4230 4230 4230 4145850 454 805 1460 1460 1460 1315 1340 2435 2435 2435 2195 2230 4060 4060 4060 3660900 482 515 1350 1350 1350 1060 860 2245 2245 2245 1765 1430 3745 3745 3745 2945950 510 310 845 1130 1130 780 515 1405 1885 1885 1350 860 2435 3145 3145 21701000 538 155 495 670 805 575 260 825 1115 1340 960 430 1370 1860 2230 16001050 566 410 595 420 685 995 705 1145 1660 11701100 593 290 340 310 480 565 515 800 945 8601150 621 205 345 5701200 649 135 225 370Hydrostatic ShellTest Pressure3350 3150 3375 5575 5225 5625 9275 8700 9375ValveClosureFluid 2442 2292 2475 4078 3817 4125 6787 6365 6875TestPressureGas 80 80 80WC6(c)WC9(c)C5(c)WCB(a)WC1(b) (c)WC6(c)WC9(c)C5(c)Note :(a) - Permissible, but not recommended for prolonged usage above about 800°F. Upon prolonged exposure to temperatureaboveabout 800°F, the carbide phase of carbon steel may be converted to graphite.(b) - Permissible, but not recommended for prolonged usage above about 850°F(c) - Use normalized and tempered material only.*For Welding end valves only. Flanged end ratings terminate at 1000°F29


STEEL PIPE FLANGESANSI B16.5 1981ANSI CLASS 150 RF TO 600 RFCLASS 150 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E BOLTin mm in mm in mm in mm in mm in mm No Dia2 50 6.00 152 4.75 120.5 3.62 92 0.75 19.1 0.75 19 4 5/82.1/2 65 7.00 178 5.50 139.5 4.12 105 0.88 22.3 0.75 19 4 5/83 80 7.50 190 6.00 152.5 5.00 127 0.94 23.9 0.75 19 4 5/84 100 9.00 229 7.50 190.5 6.19 157 0.94 23.9 0.75 19 8 5/86 150 11.00 279 9.50 241.5 8.50 216 1.00 25.4 0.88 22 8 ¾8 200 13.50 343 11.75 298.5 10.62 270 1.12 28.6 0.88 22 8 ¾10 250 16.00 406 14.25 362.0 12.75 324 1.19 30.2 1.00 25 12 7/812 300 19.00 483 17.00 432.0 15.00 381 1.25 31.8 1.00 25 12 7/814 350 21.00 533 18.75 476.0 16.25 413 1.38 35.0 1.12 29 12 116 400 23.50 597 21.25 539.5 18.50 470 1.44 36.6 1.12 29 16 118 450 25.00 635 22.75 578.0 21.00 533 1.56 39.7 1.25 32 16 1.1/820 500 27.50 698 25.00 635.0 23.00 584 1.69 42.9 1.25 32 20 1.1/824 600 32.00 813 29.50 749.5 27.25 692 1.88 47.7 1.38 35 20 1.1/4ANSI B16.47 Series A (MSS SP-44)30 750 38.75 984.2 36.00 914.4 33.75 857.2 2.94 74.7 1.38 35 28 1.1/4ANSI B16.47 Series B (API STD 605)34.94 887.4 33.31 846.1 32.00 812.8 1.75 44.4 0.88 22.23 44 ¾CLASS 300 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E BOLTin mm in mm in mm in mm in mm in mm No Dia2 50 6.50 165 5.00 127.0 3.62 92 0.88 22.3 0.75 19 8 5/82.1/2 65 7.50 190 5.88 149.0 4.12 105 1.00 25.4 0.88 22 8 ¾3 80 7.25 210 6.62 168.0 5.00 127 1.12 28.6 0.88 22 8 ¾4 100 10.00 254 7.88 200.0 6.19 157 1.25 31.8 0.88 22 8 ¾6 150 12.50 318 10.62 270.0 8.50 216 1.44 36.6 0.88 22 12 ¾8 200 15.00 381 13.00 330.0 10.62 270 1.62 41.3 1.00 25 12 7/810 250 17.50 444 15.25 387.0 12.75 324 1.88 47.7 1.12 29 16 112 300 20.50 521 17.75 451.0 15.00 381 2.00 50.8 1.25 32 16 1.1/814 350 23.00 584 20.25 514.5 16.25 413 2.12 54.0 1.25 32 20 1.1/816 400 25.50 648 22.50 571.5 18.50 470 2.25 57.2 1.38 35 20 1.1/418 450 28.00 711 24.75 628.5 21.00 533 2.38 60.4 1.38 35 24 1.1/420 500 30.50 775 27.00 686.0 23.00 584 2.50 63.5 1.38 35 24 1.1/424 600 36.00 914 32.00 813.0 27.25 692 2.75 69.9 1.62 41 24 1.1/2CLASS 600 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E BOLTin mm in mm in mm in mm in mm in Mm No Dia2 50 6.50 165 5.00 127.0 3.62 92 1.00 25.4 0.75 19 8 5/82.1/2 65 7.50 190 5.88 149.0 4.12 105 1.12 28.6 0.88 22 8 ¾3 80 8.25 210 6.62 168.0 5.00 127 1.25 31.8 0.88 22 8 ¾4 100 10.75 273 8.50 216.0 6.19 157 1.50 38.1 1.00 25 8 7/86 150 14.00 356 11.50 292.0 8.50 216 1.88 47.7 1.12 29 12 18 200 16.50 491 13.75 349.0 10.62 270 2.19 55.6 1.25 32 12 1.1/810 250 20.00 508 17.00 432.0 12.75 324 2.50 63.5 1.38 35 16 1.1/412 300 22.00 559 19.25 489.0 15.00 381 2.62 66.7 1.38 35 20 1.1/414 350 23.75 603 20.75 527.0 16.25 413 2.75 69.9 1.50 38 20 1.3/816 400 27.00 686 23.75 603.0 18.50 470 3.00 76.2 1.62 41 20 1.1/218 450 29.25 743 25.75 654.0 21.00 533 3.25 82.6 1.75 45 20 1.5/820 500 32.00 813 28.50 724.0 23.00 584 3.50 88.9 1.75 45 24 1.5/824 600 37.00 940 33.00 838.0 27.25 692 4.00 102.0 2.00 51 24 1.7/830


STEEL PIPE FLANGESANSI B16.5 1981ANSI CLASS 900 RF TO 2500 RFCLASS 900 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E BOLTIn mm in mm in mm in mm in mm in mm No Dia2 50 8.50 216 6.50 165.00 3.62 92 1.50 38.1 1.00 25 8 7/82.1/2 65 9.62 244 7.50 190.50 4.12 105 1.62 41.2 1.12 29 8 13 80 9.50 241 7.50 190.50 5.00 127 1.50 31.8 1.00 25 8 7/84 100 11.50 292 11.50 235.00 6.19 157 1.75 44.5 1.25 32 8 1.1/86 150 15.00 381 15.00 217.50 8.50 216 2.19 55.7 1.25 32 12 1.1/88 200 18.50 470 18.50 393.50 10.62 270 2.50 63.5 1.50 38 12 1.3/810 250 21.50 564 21.50 470.00 12.75 324 2.75 69.9 1.50 38 16 1.3/812 300 24.00 610 24.00 533.50 15.00 281 3.12 79.3 1.50 38 20 1.3/814 350 25.25 641 25.25 559.00 16.25 413 3.38 85.9 1.62 41 20 1.1/216 400 27.75 705 27.75 616.00 18.50 470 3.50 88.9 1.75 45 20 1.5/818 450 31.00 787 31.00 686.00 21.00 533 4.00 101.6 2.00 51 20 1.7/820 500 33.75 857 33.75 749.50 23.00 584 4.25 108.0 2.12 54 20 224 600 41.00 1041 41.00 901.50 27.25 692 5.50 139.7 2.62 67 20 2.1/2CLASS 1500 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E BOLTin mm in mm in mm In mm in mm in mm No Dia2 50 8.50 216 6.50 165.0 3.62 92 1.50 38.1 1.00 25 8 7/82.1/2 65 6.62 244 7.50 190.5 4.12 105 1.62 41.2 1.12 29 8 13 80 10.50 267 8.00 203.0 5.00 127 1.88 47.8 1.25 32 8 1.1/84 100 12.25 311 9.50 241.5 6.19 157 2.12 53.9 1.38 35 8 1.1/46 150 15.50 394 12.50 317.5 8.50 216 3.25 82.6 1.50 38 12 1.3/88 200 19.00 483 15.50 393.5 10.62 270 3.62 92.0 1.75 45 12 1.5/810 250 23.00 584 19.00 482.5 12.75 324 4.25 108.0 2.00 51 12 1.7/812 300 26.50 673 22.50 571.5 15.00 381 4.88 124.0 2.12 54 16 214 350 29.50 749 25.00 635.0 16.25 413 5.25 133.4 2.38 60 16 2.1/416 400 32.50 826 27.75 705.0 18.50 470 5.75 146.1 2.62 67 16 2.1/218 450 36.00 914 30.50 774.5 21.00 533 6.38 162.1 2.88 73 16 2.3/420 500 38.75 984 32.75 832.0 23.00 584 7.00 177.8 3.12 79 16 324 600 46.00 1168 39.00 990.5 27.25 692 8.00 203.2 3.62 92 16 3.1/2CLASS 2500 STEEL PIPE FLANGED DIMENSIONSNormal Size A B C D E Boltin mm in mm in mm in mm in mm in Mm No Dia2 50 9.25 235 6.75 171.5 3.62 92 2.00 50.8 1.12 29 8 12.1/2 65 10.50 267 7.75 197.0 4.12 105 2.25 57.20 1.25 32 8 1.1/83 80 12.00 305 9.00 228.5 5.00 127 2.62 66.50 1.38 35 8 1.1/44 100 14.00 356 10.75 273.0 6.19 157 3.00 76.20 1.62 41 8 1.1/26 150 19.00 483 14.50 368.5 8.50 216 4.25 108.00 2.12 54 8 28 200 21.75 552 17.25 438.0 10.62 270 5.00 127.00 2.12 54 12 210 250 26.50 673 21.25 540.0 12.75 324 6.50 165.10 2.62 67 12 2.3/412 300 30.00 762 24.38 629.5 15.00 381 7.25 184.20 2.88 73 12 2.3/431


CAST STEEL VALVES COMPARISON CHARTTYPE CLASS KVC KITZ WALWORTH CRANE PACIFIC JENKIN POWELL ISHIDATONGYUNG150 0112F K150SGL 5202F 47 150F 1009 1503 G2240-H 151RF008300 0312F K300SCL 5206F 33 350F 1010 3003 C2440-H 251RF008GATE600 0612F K600SCL 5232F 76 650F 1012 6003 C2640-H 351RFOD8900 0912F K900SGL 5247F 83 - - 9003 C2740-H 451RF0081500 1512F K1500SGL 5262F 87 - - 1303 C2840-H 551RF008150 0122F K150SCJ 5275F 143 160F 1040 1531 G1240-H 152RF008300 0322F K300SCJ 5281F 151 360F 1042 3031 G1440-H 352RF008GLOBE6000622F K600SCJ 5295F 161 - - 6031 C1640-H 352RF008900 0922F K900SCJ 5301F 183 - - 9031 C1740-N 452RF0081500 1522F K1500SCJ 5308F 189 - - 1331 C1840-H 552RF008150 0132F K150SC0 5341F 147 180F 1025 1561 C4240-H 153RF008SWINGCHECK300 0332F K300SC0 5344F 159 380F 1026 3061 C4440-H 253RF0086000632F K600SC0 5350F 175 680F 1028 6061 C4640-H 353RF008900 0932F K900SC0 5353F 187 - - 9061 C4740-H 453RF00815001532F K1500SC0 5356F 199 - - 1361 C4840-H 553RF00832


TERMS & CONDITIONS OF SALE• QUOTATION AND OFFERSAll goods quoted are FOB our warehouse, with inland freight to destination for account of the Buyer, either on collect basisor prepaid and billed for payment by the Buyers only. Unless otherwise stated, all quoted price are valid for 30 days only.Published price are subject to changes without prior notice.• DELIVERYDeliveries quoted are estimated basing on availability of Seller's stock and/or production schedule at time of quotation, aresubject to changes in the event of prior sales, rescheduling or any occurrence beyond the Seller's control, though theSeller, as a gesture of goodwill, will do its best to stay as close as possible to the deliveries estimated. Delivery of materialsto a common carrier shall be considered as delivery to the Buyer, and shall be at the Buyer's risk thereafter. Claims forlosses or damages to the materials in transit shall be filed by the Buyer direct with the carrier. All claims for shortages,corrections or deductions must be made to the Seller with ten (10) days after receipt of goods.• CANCELLATIONS AND RETURNSAll cancellations, changes and returns, etc... cannot be made without Seller's formal prior consents or acceptances. Acancellation and re-installation charge will apply unless otherwise waived by the Seller. Special items are not subject tocancellation or returns.• FORCE MAJEURESeller is not to be held responsible for any delays in delivery of defaults in completing an order or contract due to forcemajeure such as strikes, work stoppages, fires, floods, accidents, inability to obtain fuel and transportation means, vendors'delayed deliveries of materials, parts, components, goods, etc... to the Sellers, acts of God, and/or any other causesbeyond Seller's control.• TAXESSeller's prices are exclusive of all taxes, which, if applicable under governmental laws, shall be wholly for the Buyer'saccount and to be fully paid for by the Buyer. Where the Buyer is lawfully entitled to exemption from any tax, all necessarydocumentation must be provided by the Buyer to the Seller to effect such exemption. Any taxes, interests and penaltiesassessed against the Seller on transactions which are otherwise determined as taxable, shall be borne by the Buyer. Theterm "Taxes used here shall include any impost, duty levy or other charges imposed by any government or agency there ofupon the property, services or parties hereto, but shall not include those measured by the net income of the Seller.• ERRORSAll clerical and computational errors and/or omissions are exempted and are to be corrected by the Seller.• WARRANTYAll KVC products are guaranteed to the original Buyer only for a one year period from and after the invoice date againstdefects in material and workmanship under normal and proper use and service, and not caused or resulting from improperusage or application, improper installation, improper maintenance and repairs, modifications or alterations, normal wearand tears, corrosion, erosion or chemical attacks. Seller's obligation under this warranty is limited only to repairing orreplacing, at Seller's election, any parts or products determined by the Seller to be defective, or refunding the purchasingprice to the original Buyer. Seller shall bear normal surface transportation cost for shipping the replacements, but shall in noevent hear any losses or damages, installation, re-installation, engineering, or any other costs incurred thereof by theBuyer.• LIABILITYNotwithstanding any provision in the Buyer's order or elsewhere to the contrary, under no circumstances shall Seller beliable, in contract, tort or otherwise, for any incidental, special or consequential damages, whatsoever (Including but notlimited to loss of revenue, loss of production or loss of use of any products, or other items) whether or not arising fromSeller's negligence and delays, actual or imputed.• PARTIESThe terms "Seller" refers to KVC CO., LTD and the term "Buyer" refers to the Person, Party of Company purchasing goodsand/or services from KVC CO., LTD.33

More magazines by this user
Similar magazines