Installation Instructions Roxtec RS X

Installation InstructionsRoxtec RS XFlange and seal installationSeeAperturedimensionstableWallSleeve3-10 mm0.118-0.393”Side viewMin diameter ø (mm)Type: (Max +2mm) ø (in)RS X 43 82 3.228RS X 50 90 3.543RS X 75 115 4.528RS X 100 145 5.709RS X 125 170 6.693RS X 150 199 7.835NOT okNOT okNOT okNOT okMax Ø1mmMax Ø1mmMax ØMin ØMin Ø1mmMake a hole for the sleeve.Aperture irregularities is acceptablewithin min and max NOT recommendedokdiameters.Min ØType: Rec. Max TorqueSleeve (Nm)23-50 568-150 9NOT okSee max torqueRemove all sharp edges that coulddamage the compression rubber.Insert the sleeve.Tighten the bolts on the sleevecrosswise, in several turns. Usethe same torque on each bolt.0,1-1,0 mm0.004-0.039”Remove any dirt in the sleeve.Pull a cable/pipe through. Pleasesee note.Adapt the RS seal to the cable/pipe by peeling layers from thehalves until you reach the gap seenin pic.9.Lubricate thoroughly on the insidesurfaces and sparsely on theoutside of the seal with RoxtecLubricant.

Lubricate thoroughly on the insidesurfaces and sparsely on theoutside of the seal with RoxtecLubricant.Insert the halves, one by one, intothe sleeve.See max torqueTighten the screws crosswise.The seal will compress and sealthe transit. Please se table forrecommended max torque.Type: Rec. Max TorqueRS(Nm)23-31 143-100 4125-150 7The torque depends on several thingse.g pipe size and material, amount ofused lubricant or sleeve size etc.ASS2006005201 ver_1.3/GB/0947/olaherDisassemblyReverse orderNote For optimum relability, wait 24 hours or longer after installation before exposing the cables/pipes to strain or pressure. Cable/pipe shall be routed perpendicular to the sleeve or whole. Cable/pipe of considerable weight must be supported by surrounding structure or equipment to prevent damage or subsidence to the seal.DISCLAIMER”The Roxtec cable entry sealing system (”the Roxtec system”) is a modularbasedsystem of sealing products consisting of different components. Eachand every one of the components are necessary for the best performance ofthe Roxtec system. The Roxtec system has been certified to resist a numberof different hazards. Any such certification, and the ability of the Roxtec systemto resist such hazards, is dependent on all components that are installed as apart of the Roxtec system. Thus, the certification is not valid and does not applyunless all components installed as part of the Roxtec system are manufacturedby or under license from Roxtec (“authorized manufacturer”). Roxtec gives noperformance guarantee with respect to the Roxtec system, unless (I) all componentsinstalled as part of the Roxtec system is manufactured by an authorizedmanufacturer and (II) the purchaser is in compliance with (a), and (b), below.(a) During storage, the Roxtec system or part thereof, shall be kept indoorsin its original packaging at a temperature not exceeding +70°C/+158°F andnot below -40°C/-40°F.(b) Installation shall be carried out in accordance with Roxtec installation instructionsin effect from time to time.The product information provided by Roxtec does not release the purchaser of theRoxtec system, or part thereof, from the obligation to independently determinethe suitability of the products for the intended process, installation and/or use.Roxtec gives no guarantee for the Roxtec system or any part thereof andassumes no liability for any loss or damage whatsoever, whether direct, indirect,consequential, loss of profit or otherwise, occurred or caused by theRoxtec systems or installations containing components not manufactured byan authorized manufacturer.Roxtec expressly excludes any implied warranties of merchantability and fitnessfor a particular purpose and all other express or implied representations andwarranties provided by statute or common law. User determines suitability ofthe Roxtec system for intended use and assumes all risk and liability in connectiontherewith. In no event shall Roxtec be liable for consequential, punitive,special, exemplary or incidental damages.”Roxtec International ABBox 540, 371 23 Karlskrona, SWEDENPHONE +46 455 36 67 00, FAX +46 455 820 12EMAIL info@roxtec.com, www.roxtec.comRoxtec ® and Multidiameter ® are registered trademarks of Roxtec in Sweden and/or other countries.