Chemguard Foam - Security tech

Chemguard FoamFirst Class Foam ConcentrateThe U.S.D.A. Forest Service has approved Chemguard First Class as meeting all of the requirementsof U.S.D.A Forest Service specification 5100-307. It has passed NFPA 18 wetting agent standard2006 Edition. This standard tests the agent at dilution rates of 0.1% to 1.0% for use on Class A fuels.First Class combines excellent wetting characteristics with great foam formation for superioreffectiveness on Class “A” Fires. For use in ground trucks, CAF Systems, helicopter and fixedwing aircraft with buckets, water scooper or tanks. Contains no hazardous material, safe for theenvironment. First Class works very well with CAFS at ratios of 0.4% or greater. Ship. wt. 45 lbs.Wildland fires Ground applications Aircraft applicationsPriced per gallon, sold in 5-gallon containersBB135 First Class Foam Concentrate /gal.FOAMClass A & Wetting AgentsClass A Foams/Wetting Agents - Chemguard’s Class A foam concentrate is a mixture offoaming and wetting agents. When proportioned with water it changes the properties ofthe water, reducing the surface tension and allowing for greater penetration in all Class A fueland wildland fires. It also gives the water a foaming ability, allowing it to remain and clingto the surfaces without run off. Class A is effective in fighting forest fires and many deep-seatedfires such as tires, paper, and wooden structures. Class A Plus works very well with CAFS at ratios0.5% or greater.Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceAC721 Class A Plus Non-corrosive, Non-Toxic Biodegradable.For rates of 0.1% - 1.0%. Meets NFPA 298 /gal.AC724 Chemwet Highly Concentrated Wetting and PenetratingAgent (Allows for Quicker Extinguishmentand Stretches Water Supply) /gal.High Expansion FoamsHigh Expansion Foam Concentrates - These agents are synthetic based and are suitablefor use with low, medium or high expansion foam generating equipment. Normally used ata proportioning rate between 1 and 3%, they are used in contained areas such as miningoperations, ship hold areas, etc. where volume fire control is required. A high expansiongenerator can be used to fill the entire area with a large amount of very light, expandedfoam bubbles, and depending upon the type of generator, ratios of up to 1,000 to 1 canbe achieved. Fires involving solid materials as well as flammable liquids can be controlledand extinguished. High expansion foam also has special advantages in dealing with spillsof Liquified Natural Gas (LNG).Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceAC722 X-TRA High High Expansion Foam Provides Superior FireSuppression Expansion and Vapor Barrier Againsta Broad Range of Materials /gal.Training FoamTraining Foam Products - Supertrain is specially designed synthetic foam formulationswhich are biodegradable and environmentally friendly for use in live fire-training sessions.This formulation is suitable for use with both fresh and salt water and can be used with allsiliconized dry chemical agents and can be proportioned at either 3% or 6%.Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceAC723 Supertrain Training Foam Cost Effective Training /gal.Contact Your Darley Representative With Your Protein or Flouroprotein Foam Needs1.800.323.0244 | www.edarley.com/foam145

FOAMChemguard FoamAqueous Film Forming Foam (AFFF)Aqueous Film Forming Foam (AFFF) - is a specially formulated syntheticconcentrate. A vapor suppressing aqueous film is formed by foam solution drainingfrom the expanded foam blanket. These products are intended for use atproportioning rates of 1%, 3% and 6% on Class B hydrocarbon type fuels suchas; crude oils, gasoline, kerosene, diesel fuel and aviation fuels. AFFF’s alsoexhibit excellent wetting characteristics when used on Class A fires. Both aspiratingand water fog type nozzles are suitable when using these foams. Either fresh orsea water may be mixed with these foams to achieve excellent results.Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceAC719 3% AFFF An Industry Standard, the MostCommonly Used AFFF /gal.AS290 3% AFFF Highest Quality AFFF AvailableMil. Spec on QPL MIL-F-24385F Listed /gal.AC720 6% AFFF Lowest Cost AFFF /gal.AS292 1% AFFF Requires Less Concentrate Than 3% or 6% Products /gal.Alcohol Resistant AqueousFilm Forming Foam (AR-AFFF)Alcohol Resistant Aqueous Film Forming Foam (AR-AFFF) - is speciallyformulated with a physical polymer membrane/barrier between the fuel surfaceand the foam blanket. They are intended to be used at proportioning ratios of1% and 3% for hydrocarbon fuels and 3% or 6% for polar fuels such as alcohol,ketones, methanol and MTBE products. AR-AFFF’s may also be used on Class Afires. AR-AFFF’s suppress the hazardous vapors emitted from these polar andhydrocarbon fuels. Chemguard’s AR-AFFF’s are suitable for use with foam chambers,standard water fog nozzles, air-aspirating nozzles and foam makers.Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceAC717 3%x6% AR-AFFF Concentrate for Use on Both Hydrocarbonand Polar Solvent Fuel Fires /gal.AS291 3%x3% AR-AFFF AR-AFFF Keep Mixture Ratio theSame for all Fires, EliminateCostly Mistakes /gal.BD197 1%x3% AR-AFFF Highest Quality AR-AFFF Cost Effective1% Hydrocarbon and 3% Polar Solvents /gal.Low Temperature FoamBD018 and BD019 - Freeze protected 3%-3% proportions 3 parts concentrate to 97parts water for hydrocarbon and polar fuels. Intended for top side use on type II andtype III applications. UL listed. Ship. wt. 45 lbs.BD020 - Freeze protected AFFF Solution, good to minus 40˚F. This product is notintended to be proportioned. Works well on Class B fires. Designed for use in Trimaxunits and flight line extinguishers.Priced per gallon, sold in 5-gallon containersCat# Description Benefits PriceBD018 3% AFFF Low Temperature Foam, UL Listed toMinimum Use Temperature of -20˚F /gal.BD019 3% AR-AFFF Ultraguard Low Temperature Foam /gal.BD020 Foam Solution Blizzard Freeze Protected SolutionFoam Temperature Range of -40˚F /gal.Contact Your Darley Representative With Your Protein or Flouroprotein Foam Needs146 1.800.323.0244 | www.edarley.com/foam

Practice Foam Train for Pennies!Practice Foam is an answer to the requests “give us an inexpensive product to train with!” Practice Foam isa variable percentage Class A type product. Safe and inexpensive to use, Practice Foam may be educted atlow to high percentages to achieve the desired results of your training session. Although not intended for a“working fire”, Practice Foam is entirely suitable for extinguishing training ground fires.Non-toxic, biodegradable and self-dissipatingFor training only; NOT for fire fightingPlenty of suds - no clean up requiredBG113Practice Foam /5-gal. pailX-pando Foam ConcentrateA detergent type variable percentage/variable expansion blend of foaming and wetting agents intended forClass A and B fires. Use through a CAFS or eductor to produce volumes of high-expansion foam or withregular foaming equipment consistent with the type of foam required. X-pando may be used with mostfoam making equipment. X-pando extinguishes with volumes of wet, moist foam, cutting the oxygen supplywhile creating cooling steam as the area is blanketed or completely filled. Used at 3% or less, X-pandooffers low percentage use rates combined with reasonable per-gallon cost and infinite shelf life to give youa “general purpose foam value”.FOAMBG115X-pando Foam Concentrate /5-gal. pailPhos-Chek Class A FoamProvides superior foam generation at 0.1-1% use concentration. Phos-Chek has been tested by the U.S. ForestService and is approved for use from ground engines, helicopter buckets, and helicopters equipped with fixedtanks. It is a U.L. listed wetting agent at 0.25% use rate effective on both Class A & B combustibles. Meets therequirements of NFPA 1150. Contains no EPA listed hazardous materials. PhosChek Class A works very wellwith CAFS at ratios of 0.2 to 0.3% and can produce the good dry foam associated with CAFS. Ship. wt. 45 lbs.Priced per gallon, sold in 5-gallon containersAS285 Phos-Chek 5-gal. Container /gal.AS289 Phos-Chek 55-gal. Drum /gal.AS286 Phos-Chek 4 oz./Case of 36Silv-ex Foam ConcentrateA multiple expansion Class A foam concentrate formulated from specialty hydrocarbon surfactants, stabilizers,inhibitors and solvents. Its combination of surfactants and solvents provides extremely good cold weatherperformance. The original forest fire control concentrate. Proven effective on many deep seated Class A fires.Can be proportioned from 0.1% to 1.0% in fresh, brackish or sea water. Silv-ex works very well with CAFS atratios of 0.2 to 0.3% and can produce very good dry foam associated with CAFS. Ship. wt. 45 lbs.Priced per gallon, sold in 5-gallon containersAB410 Silv-ex Foam Concentrate /gal.Foam Cap WrenchMade from aluminum alloy the wrench loosens and tightens 70mm foam containercaps with ease. Wrench is 9 1 /2" long with an outside diameter of 3 1 /4". Ship. wt. 1 lb.AF640 Foam Cap WrenchX-Stream Premium Class A FoamChemguard has introduced X-Stream, the first and only premium Class A foamconcentrate designed specifically for compressed air foam (CAFS). When mixed withwater at concentrations of 0.1 - 1.0%. X-Stream produces a supper-thick foam with a significantly longerthrow distance that clings to horizontal and vertical surfaces with minimal runoff drastically reducingburnback.Priced per gallon, sold in 5-gallon containersBH124 X-Stream Premium A Foam /gal.1.800.323.0244 | www.edarley.com/foam147

FOAMPRO/pak Foam SystemEverything You Need in One Portable Unit to Apply Foam QuicklyMaking great foam is easy with the PRO/pak. Everything you need iscontained in one lightweight package that attaches to the end of your 1"fire hose. It can work on pressures as low as 50 psi. With its small size andversatile nozzles you can have foam capability without the expense of built-insystems costing thousands of dollars. Features a high-impact 2 1 /2 gallon foamreservoir with built-in eductor that can be set to the ratio of your choice.Large, easy-open fill port has an indicator to show the type of liquid in thetank. The flow is controlled by a twist grip valve/carrying handle. With eachquarter turn you select the discharge velocity for inlet pressures between40 and 500 psi. System comes complete with a straight stream nozzle, lowexpansion nozzle and medium expansion nozzle. Nozzles can bedirectly attached to the eductor for one-handed operation, or a shortsection of hose can be added for maneuverability. Designed for Class A3% or 6% AFFF & AR Foams. Ship. wt. 15 lbs.Includes:PRO/pak UnitShoulder Strap3' Extension Hose3 - Quick-Connect NozzlesSpecify inlet threads; 1" NH or NPSHAJ255 PRO/pak Foam SystemAJ256 Piercing NozzleAJ257 Mounting BracketAJ258 25' Discharge HoseAJ259 Waist StrapHandy FoamPortable Foam Unit With Self-Educting Foam NozzleBrings you everything you need in one package for your portable foam application.The latest in foam making with the exclusive self-educting foam nozzle withremovable metering devices (0.4%, 1%, 3% and 6% concentration) that eliminate theuse of eductors that have exceptionally high pressure drop. That means you can workat lower pressure from 30 to 60 psi and always accomplish a better reach andexpansion ratio than with anything else you have used before. The foam unit’sergonomic and lightweight design is made from a high-impact polyethylene, andincludes a tank that holds 2.5 gallons. The unit has a 20 gpm Low Expansion Nozzle,shoulder straps and storage bracket. Ship. wt. 22 lbs.AR197Handy FoamPrecision Foam Testing KitThe Precision Foam Testing Kit is designed to simplify the process of testing foamsystems for proportioning accuracy. This kit utilizes liquid conductivity and aprecision digital scale to accurately prepare standards and test discharge samples;the same method used by nationally recognized testing laboratories when testingsystems for listing and approval. Ship. wt. 6 lbs.Includes:1 - Protective carrying case with foamprotective padding1 - Precision digital electronic 250 gramscale with 0.1 gram accuracy6 - 150ml graduated sample beakers1 - 100ml graduated cylinder1 - 250ml wash bottle2 - 10ml sample pipettes (12" L)5 - 3ml sample pipettes (6" L)1 - 500ml water sample bottle2 - 10ml sample syringes10 - Test charts (reproducible)1 - Instruction manualAZ292Precision Foam Testing Kit148 1.800.323.0244 | www.edarley.com/foam

FoamPro ® 1600 Series Proportioning SystemNo other system delivers foam as easily and accurately as the FoamPro ® . All it takes is a flip ofthe switch to start the system. FoamPro ® adjusts automatically to any changes in flow rate orpressures. Plus, the patented, high-tech, electronic controller does all of the work for you.To make the foam wetter or drier simply adjust the dial to change the foamconcentrate level. When you use the FoamPro ® , you don’t have to worryif the foam solution is correct-the system does the proportioning allautomatically. Simply set the percentage you want on the controlmodule. Because the precise proportioning is done by measuring flowinstead of pressure, you do not have to shut down to add lines, change pressureor refill the foam tank. What’s more, the FoamPro ® conveniently interfaces withCompressed Air Foam Systems. Meets NFPA Standards. Ship. wt. 68 lbs.Exclusive FeaturesAutomatic proportioningAdjustable dial controlProportions continuouslyNo foam goes through the fire pumpTank Sensor requiredAJ247 FoamPro ® with 1 1 /2" FlowmeterAJ248 FoamPro ® with 2" FlowmeterAJ249 Tank Sensor, Vertical MountAvailable OptionsAJ251 8 gal. Polypropylene Foam TankNo in-line restrictionsInstalls in new or existing apparatusDelivers 0.1 to 1.7 gpm of concentrateFOAM36 Gallon Mobile Foam CartFeatures a fiberglass tankNozzle features a ball type shut-off valve for better stream control and isdesigned to give a constant flow rate with either a straight stream or “Fog” patternIncludes 50' of 1 1 /2" rubber lined, single jacket fire hose with lightweight 1 1 /2"NST couplingsIncludes 3"x16" pneumatic tiresPick-up tube on the in-line eductor is manufactured in stainless steelEductor has variable metering valve settings for 1%, 3%, and 6%Available in either a 60gpm or 95gpm flow rateCat# Description Includes Ship. wt. PriceBG161 36 gal. Foam Cart 1 1 /2"x50' Hose/95 gpm Eductor/Handline Nozzle 150 lbs.BG162 36 gal. Foam Cart 95 gpm Eductor 145 lbs.Macaw BackpackMiniaturized CAF PowerOriginally designed for rapid attack in firesuppression, this miniature 5-gallon (18.9L) CAFpowerhouse expands foams up to 70:1 dependingon nozzle and foam solution used. The Macawcan effectively deploy liquid formulas, air aspiratedfoam and CAF with simple control adjustments.Ship wt. 30 lbs.Proven effectiveness for:Mop up and overhaul operationsHazardous material clean upClass A and B fire suppressionVapor suppressionDecontamination operationsWet line constructionCAF trainingNuisance fires and spillsPurchase includes nozzle shownAM234 Macaw Backpack with Cylinder, 4500 psiAM235 Macaw Backpack without CylinderAM236 Fan Tip NozzleAM237 Piercing Applicator Tip1.800.323.0244 | www.edarley.com/foam149

Foam Proportioning Systems and CAFSFast Foam 50 or 250APPLICATIONSMini pumper – 50, 250Pumper tanker – 250Pumper – 250Wildland – 50, 250FOAMSTANDARD EQUIPMENTStainless steel check valveVenturiPanel mounted controllerInstallation kitFast Foam 250Fast Foam 50Features: The Fast Foam systems offers a reliable, accurate, compact foamproportioning system at an economical price. The systems are optional and foruse on single and dual line systems.Model Performance Dimensions Weight PriceFast Foam 50 Up to 50 gpm @ 1% at pressures up to 175 psi 19"Lx10"Wx14"H 64 lbs. (29 kg)Fast Foam 250 Up to 250 gpm @ 1% at pressures up to 250 psi 21"Lx10"Wx12"H 75 lbs. (34 kg)Odin AutoValve KitsThe AutoValve is actually two programmable electric ball valves: onewater, one air, which respond to commands from a remote placard.Depress the button which has the flow type desired, and the valvesmove to pre-programmed flow rates. If you forget to turn on yourchemical solution system or run dry of chemical during operations,the AutoValve will flash a warning light, turn off the air and move thewater valve to a fully open position. Front bumper monitors requirevariable flow rates that currently are very hard to attain with normalelectric valves, especially while driving. This valve will deliver CAF and Side Viewfull flows with the ease of one button! Versatile! This is of real valueto firefighters and to OEM's with crowded building requirements. The AutoValve kitalso adapts as a retro fit on Akron and Elkhart ball valves.Kit Includes:Controller with wiring harnessSolution valve and actuator, stainless steelModel Description PriceDAV001.5 Standard 1 1 /2" AutoValve KitDAV002.0 Standard 2" AutoValve KitPTO Driven Compressor KitAPPLICATIONSMini pumperRescue pumperTactical tenderWildland/InterfaceInstruction manualAir valve and actuator, stainless steelSTANDARD EQUIPMENTCustom control panel with full instrumentationRotary screw compressorAutoOdin balance valve systemFactory assisted installationAvailable in 150 and 200 cfmFeatures: The compressor receives its power from the apparatus transmission PTO. Please consult Odin for the correct engineeringapplication. Pump is supplied by customer. 2 1 /2” and 3” standard and expanded kits are available. Please call Odin at 877-634-6223 for moreinformation.Model Performance (Air) Dimensions Ship. Wt. PricePTO Driven Compressor Kit 200 cfm @ 125 psi Contact Odin Foam for Schematic 600 lbs. (272 kg)150 cfm @ 125 psi and CAD Drawings of Components 550 lbs. (249 kg)150 1.800.323.0244 | www.edarley.com/foam

Pyrolite ® In-Line EductorsUltra Light Foam Eductorswith By-PassAkron Municipal Eductors feature a large, easy to read, andremovable metering dial with infinite settings between 0 and 6%.Detents at 1 /4, 1 /2, 1, 3, and 6%. The Eductors are rated to flow at200 psi (14 bar) inlet pressure and works well with nozzles ratedat 75 and 100 psi (5 and 7 bar). Ship. wt. 8 lbs.1 1 /2" or 2 1 /2" swivel inlet x 1 1 /2" male, except where noted30" pickup hose standard on 60, 95, and 125 gpm(230, 360, and 475 lpm) eductors, 48" optional48" pickup hose standard on 250 gpm (950 lpm)AZ340AZ341AZ342AZ343Pyrolite ® In-Line Eductor 60 gpmPyrolite ® In-Line Eductor 95 gpmPyrolite ® In-Line Eductor 125 gpmPyrolite ® In-Line Eductor 250 gpmClass A Foam Mixer Systemfor Portable PumpsSampling NozzleDischarge AdapterSuction AdapterFoamMixerOperates in accordance with the “Venturi” principle. As thepressurized water passes through the tip of the convergent pipe,a suction effect is created and the foam concentrate liquid isdrawn up. Metering device regulates the foam concentration flow.Eductor includes tips to change foam percentage, by-pass switch,metering device and clear PVC pick-up tube with braided suctionhose. Ship. wt. 3 lbs.Cat# GPM Inlet Outlet Foam Percentage PriceAM153 60 1 1 /2" 1 1 /2" 0.4%, 1%, 3%, 6%AM154 95 1 1 /2" 1 1 /2" 0.4%, 1%, 3%AM139 125 1 1 /2" 1 1 /2" 0.4%, 1%, 3%Darley Around-The-PumpProportioning KitThe Darley Around-The-Pump Proportioning Kit is a simple andinexpensive way to add foam capability to all discharges of atruck. It allows for different flow requirements separately or inany combination. A portion of the truck output goes through aneductor and back to the inlet side of the pump. A metering valveis adjusted for the correct foam percentages based on the totaldischarge.This system offers several advantages when compared to an inline eductor:Variable Flow Rate - Discharge rate can be adjusted for the specificapplication. The rate is infinitely variable up to the max. flow of the unit.Variable Pressure - System operates at any pressure above 120 psi.The pump operation is the same with foam or water.No Back Pressure Restrictions - Unit is not affected by hose length orelevation loss.No Nozzle Restrictions - Unit operates with any size or type of nozzle.Note: Maximum 5 psi Hydrant Pressure.Inexpensive & simple to useFoam at all outletsMax. 3% flow - 400 gpm - 1515 lpmMax. 6% flow - 200 gpm - 757 lpmDrive flow - 25 gpm - 95 lpmKit Includes:A. EductorB. Metering ValveC. Check ValveD. Water ValveE. Foam Valve InstructionPanel PlateVariable flow ratesNo friction loss orelevation restrictionsBEFoamLiquidTankFOAMThis foam-making kit can be attached to a forestry firefightingpump. The kit consists of a 2" suction hose adapter, a 1 1 /2"discharge hose adapter which is equipped with a shut-off valveand foam sampling nozzle and a variable around-the-pump foamliquid concentrate mixer with a pick-up tube. The inductor can beadjusted to pickup liquid concentrate in quantities small enoughfor the smallest nozzle, all the way up to an amount large enoughto treat over 150 gallons of water per minute. The quality ofwater/foam solution being produced can easily be determinedby the foam sampling nozzle located on the discharge hoseadapter. The mixer can be fitted to most pumping units.AC993Class A Foam Mixer SystemG365AM152WaterTankCADarley Around-The-Pump Proportioner Kit,(Down to 1%@ 60-400 gpm)Darley Around-The-Pump Proportioner Kit,(Down to 0.5% @ 100-1400 gpm)D1.800.323.0244 | www.edarley.com/foam151

FOAMThis master streamnozzle has its ownbuilt-in foam eductorso it can be used for water applicationor AFFF application. By simplyattaching the Hydro-Foam to yourexisting fixed monitor or portablemonitor, you have an instant AFFFWater or foamstation. Attach one to the deck gunof your pumper and you have foamcapabilities similar to a crash truck. It isideal for those situations where greater application rates arenecessary for containment and/or extinguishment of large spills.Designed, developed, and field tested by firefighting specialists.Since its inception the nozzle has been used successfully toextinguish many flammable liquid tank fires. The Hydro-Foam isavailable in two gallonages. The Y246 (350 gpm) is pre-set for 6%proportioning but can be easily changed to 3%, 1% or 1/2%. TheY247 (500 gpm) is pre-set for 3% proportioning and can bechanged to 1%. Each nozzle comes with 9' of clear vinyl pick-uphose. UL tested. Ship. wt. 2 - 19 lbs.Optional DrumPick-Up KitHydro-FoamNozzleKit includes PVC pick-up tube,PVC shutoff valve, brass vacuumbreaker and 9ft. of clear, reinforcedpick-up hose.AC989 Drum Pick-Up Kit $353.95Hydro-Foam Nozzlewith Built-In EductorMonitorFromPumpY246 Hydro-Foam Nozzle (350 gpm) ChromeY24601 Hydro-Foam Nozzle (350 gpm) BrassY247 Hydro-Foam Nozzle (500 gpm) ChromeY24701 Hydro-Foam Nozzle (500 gpm) BrassAC986 Foam Selector Valve, 3%-6%AC987 Optional Quick-Connect Coupling, BrassAC988 Optional Shutoff Valve, BrassTubingDrumKitBy-Pass Foam EductorFemale swivel inlet and male outlet, infinite metering valve settingbetween 0% to 6%, pick-up tube and clear PVC pick-up tube/hose.Rugged corrosion-resistant construction; red epoxy finish.Ship. wt. 8 lbs.Portable In-Line Foam EductorsThe first necessity of any handline foam system is a means ofintroducing foam concentrate into the water supply. The simplest,most-efficient and least-expensive way of doing this is a portablefoam eductor. These “Venturi” eductors are constructed ofrugged brass alloys. Their efficient and simple design assures thelowest possible friction loss. Metering devices on all these eductorsare easily removed for cleaning and are designed with a stainlesssteel ball check to prevent foam contamination when the line isshut down. Metering device on 60, 95, 150 and 250 gpm modelshas five settings: 1/2%, 1%, 3%, 6% and 0 (positive shutoff);Eductors are suitable for all types of foams.Ship. wt. 10 lbs. Specify inlet size.Eductor with female swivel inletand male outletRemovable metering/checkvalve and pick-up tubeClear PVCpick-up hoseMax.Cat# GPM Inlet Outlet Hose Trim PriceH580 60 2 1 /2"or 1 1 /2" 1 1 /2" 300' ChromeH581 60 2 1 /2"or 1 1 /2" 1 1 /2" 300' BrassW201 95 2 1 /2"or 1 1 /2" 1 1 /2" 150' ChromeW202 95 2 1 /2"or 1 1 /2" 1 1 /2" 150' BrassH582 125 2 1 /2"or 1 1 /2" 1 1 /2" 300' ChromeH583 125 2 1 /2"or 1 1 /2" 1 1 /2" 300' BrassW203 250 2 1 /2" 2 1 /2" 200' ChromeW204 250 2 1 /2" 2 1 /2" 200' BrassAZ297 150 2 1 /2"or 1 1 /2" 1 1 /2" 150' BrassAZ298 150 2 1 /2"or 1 1 /2" 1 1 /2" 150' ChromeRound The Pump FoamInductor/MixerAn economical and easy-to-use method for foam induction.Inducts foam concentrate into the hose lines of portable pumps.Perfect for use in wildland fires. Designed with a control knobcalibrated to induct foam concentrate ratios of .1%, .5% and 1%into hose lines flowing 8, 15, 30 and 50 gpm. Ship. wt. 1 lb.1.5"x1.5"x75" tee connector 2"x2"x75" tee connectorCat# GPM Inlet Outlet PriceAR147 60 1 1 /2" 1 1 /2"AR148 95 1 1 /2" 1 1 /2"AR149 125 1 1 /2" 1 1 /2"152 1.800.323.0244 | www.edarley.com/foamAJ253Round The Pump Foam Inductor/Mixer

AC992Bubble Cup NozzlesThe dual or single-gallonage Bubble Cup nozzle is a uniquely designed aspirating fog/foam nozzle created to be used with AFFF and Protein type foams for fire brigadesand hazardous materials incidents or for structural and wildfire applications of Class Afoaming agents. Capable of producing a conventional straight stream, wide protectivefog pattern and aspirating foam, the Bubble Cup is a nozzle that provides an extrameasure of protection. Nozzles are backed by a full 5-yr factory warranty and 24-hrcertified repair. Ship. wt. 4 lbs.Specify gpm: 20/60 or 20/95AC990 Bubble Cup Nozzle Tip, 1 1 /2"AC991 Bubble Cup Nozzle with Shut-Off, 1 1 /2"AC992 Bubble Cup Nozzle w/Shut-Off & Pistol Grip, 1 1 /2"Low Expansion Foam NozzleAvailable in 60, 95-125 & 200-250 gpm @ 100 psiLighter than previous styleTube is only 8” in lengthAluminum construction w/NITUFF finishGreat expansion ratio of 1010 year warrantyCat# GPM Inlet PriceBH138 60 1 1 /2"BH139 95-125 1 1 /2"BH140 200-250 1 1 /2"Nothing Foams Like A “Madd Dog”Expansion Aspirating Foam AttachmentThe Madd Dog Attachment makes better foam than any other multiple expansion aspiratingnozzle. Designed by a fire captain with firefighter safety, quality, versatility, performanceand cost in mind. Produces low-expansion foam with excellent stream projection ormedium expansion foam with incredible production. The aspirating attachment isconstructed of pressure-injected polymer resins which make it economical, lightweightand incredibly rugged and will fit a variety of combination nozzles. Ship. wt. 2 lbs.FOAMISO PointsAK244L685Madd Dog Foam Attachment1 1 /2” Lexan NozzleFoam Nozzle w/Pick-Up TubeThese 1 1 /2" and 2 1 /2" aerating type foam nozzles are lightweight, cordwrapped and include a clear PVC hose and strainer and pick-up tubewhich means each tube requires no eductor and can draw foamdirectly from a container. The AG129 and AG174 foamnozzles are the most inexpensive way to deliver foamin the 60 to 95 gpm range and are very lightand easily handled. Maintenance andcleaning are very simple. The AG175foam nozzle delivers 120 gpm ofNo eductorrequiredAG174AG129AG175foam and can be used with 2 1 /2" lines. Itwill supply foam in an expansion ratio ofapproximately 14 to 1 and would be suitable formost small spills and foam application requirements.Ship. wt. 7 lbs.Foam Nozzle w/Pick-Up Tube, 1 1 /2" Swivel,60 gpm, 36 1 /4"LFoam Nozzle w/Pick-Up Tube, 1 1 /2" Swivel,95 gpm, 38"LFoam Nozzle w/Pick-Up Tube, 2 1 /2" Swivel,120 gpm, 41"LBlizzard Wizard ®Class A Foam NozzlesBlizzard Wizard ® foam nozzles are rated at11, 23, 34, 50 and 60 gpm at 100 psi nozzlepressure. The unusual long reach-of-stream(up to 75') is possible because of the patented“turbulence induction plates” that use such asmall amount of available water pressure to makefoam. Nozzle body is made of ABS plastic;AC994 made of hard anodized aluminum.Ship. wt. 2 lbs.FlowCat# Size (GPM) Stream PriceAF850 1 1 /2" NST 50 75'AF851 1 1 /2" NST 34 70'AF852 1 1 /2" NST 23 50'AF853 3/4" GHT 11 45'AC994 1 1 /2" NST 60 75'1.800.323.0244 | www.edarley.com/foam153

FOAMFoam-Fast Wildfire Pre-Treatment KitClass A foam in an easy-to-use, affordable applicator forpretreatment during the threat of a wildfire or as a safetyprecaution when managing burn piles, mowing or trimmingweeds. Simply place the foam cartridges in the applicator, attach toa standard garden hose, and Foam-Fast is ready to operate! Eachcartridge produces 3 gpm of foam for approximately one hour onas little as 30 psi of water pressure.Features:Mixing chamberFoam nozzleInstruction manualInstructional DVDBi-Lingual English/Spanish packagingBH025 Includes:Three foam cartridges3/4" shutoffBK019 Includes:Six foam cartridges1 1 /2" NH shutoffStandard gardenhose attachmentBH025BK019Foam-Fast Wildfire Pre-Treatment KitFoam-Fast KitQuick-Attack FoamAeration TubesPyrolite ® foam tubes are designed to easily and quickly clampon to various Akron ® nozzles. use the chart below to determinethe proper Quick-Attack foam tube. Ship. wt. 3 lbs.Reach up to 75'Provides air-aspirated foam capability - up to 12:1 expansionratio with AFFFFlow: AF26401 - 30 gpm, AF26409 - up to 250 gpm,all others up to 125 gpmLength: AF26401 - 11 1 /2", all others 16 3 /4"Solid Foam TechnologyNo Eductors, No Foam PailsBumperCat# Nozzle Years Diameter PriceAF26401 1" TurboJet 2000 - Current 3"1" Assault 2000 - Current 3"Force & Defender All 3"AF26402 1 1 /2" TurboJet Pre 1993 3 3 /8"1 1 /2" Industrial TurboJet All 3 3 /8"AF26403 1" TurboJet 1993 - 2000 3 5 /8"1 1 /2" TurboJet 1993 - Current 3 5 /8"AF26404 Mid-Range TurboJet 1993 - Current 4 1 /2"Mid-Range & 2 1 /2" SaberJet All 4 1 /2"AF26405 1 1 /2" Marauder w/Molded Teeth All 3 5 /8"1 1 /2" 3015-3021 All 3 5 /8"AF26406 1 1 /2" Marauder w/Spinning Teeth All 3 3 /4"AF26407 1 1 /2" & Mid-Range Assault All 3 7 /8"Wide-Range TurboJet All 3 7 /8"1" & 1 1 /2" SaberJet All 3 7 /8"AF26408 Mid-Range Akromatic All 4 1 /4"2 1 /2" Industrial TurboJet All 4 1 /4"AF26409 2 1 /2" TurboJet 1993 - Current 4 1 /2"Mid-X Medium ExpansionFoam TubeThe Quick STIK system uses solid foam/wetting agent that isinserted into the specially perforated foam sleeve. Matched upwith a 30-60-95-125 gpm adjustable nozzle, this Quick STIK systemcan deliver up to 600 gallons of foam/water mixture per stik.BC141BC054BC055BC056Foam Proportioner withQuick STIK TechnologyTS TURBO AFFF/AR 12/csTS ECO Class A 12/csTS CLEAN STIK Degreaser 12/csCapable of foamexpansion to 50:1Maximum flow 250 gpmMaximum pressure 100 psiShip. wt. 5 lbs.AZ294AZ295AZ296For Use On Akron 1 1 /2" Turbojet NozzlesFor Use On Akron Mid-RangeTurbojets, Mid-Range Saberjets and2 1 /2" Saberjet NozzlesFor Use On Akron 1 1 /2" Assaults, Wide RangeTurbojets, 1" & 1 1 /2" Saberjet Nozzles154 1.800.323.0244 | www.edarley.com/foam

CAFS 2 1 /2" Handline NozzleMade of lightweight anodized aluminum. The discharge does not “flatten out” foambubbles. Allows for increased flow rates of foam solution and compressed air. Includesaluminum smooth bore tip with smooth inside taper for solid stream. 2 1 /2" NST Inlet andoutlet threads. Ship. wt. 5 lbs.AS293CAFS 2 1 /2" Handline NozzleCompressed Air Foam NozzleIdeal for use with compressed air foam. Made of lightweight anodized aluminum.The discharge does not “flatten out” foam bubbles. Ball valve has 1 3 /8" unobstructedwaterway. Other features includes pistol grip, quick-change rear valve seat andshut-off ball and smooth bore tip with smooth inside taper for solid stream. NST threads.Ship. wt. 5 lbs.Cat# Size Tip PriceAR165 1 1 /2" 1 1 /4"AR166 1"15/16"Flex Attack ® NozzleGo from CAF to H 2 O with a Click of the TipThe Flex Attack ® CAF nozzle quickly switches between wet foam, dryfoam and water only without shutting down. Now there’s no need tocompromise when fire fighting. Click left for a huge, unobstructedwaterway to produce shaving cream dry foam. Click right for a hardhitting 15 /16" smooth bore. The Flex Attack ® is durable, dependable,best of all, simple to use.Free swivel inletHard anodized, Teflon ® impregnated aluminum alloy body and pistol gripUltra-high molecular weight, polyethylene shut-off seatsAluminum bronze shut-off handleZytel ® ST801 polyamide center barrel70A urethane compressible boreMax operating pressure of 200 psi184 gpm @ 50 psi in Water SettingFOAMBG512Flex Attack ® Nozzle2 1 /2" CAFS PistolGrip NozzleCAFS-Force NozzlesPressure for foamand waterDo you want to pack the most CAFS punchpossible in a 2 1 /2” hand line? Most 2 1 /2”nozzles are nothing more than a 1 3 /8” waterwayshutoff with a 2 1 /2” swivel inlet. Not thisnozzle… this pistol grip ball shutoff features a2 1 /2” swivel inlet and a 2 1 /2” threaded outlet with a full 2” internal ballopening. This allows more CAFS to be propelled unobstructedthrough this lightweight pistol grip ball shut-off. We also finish off thisBrutus of a shut off with a set of dual stacked tips so you can choosebetween the 2 1 /4” and a 2” tip opening. Easily flows 120gallons per minute of foam solution and 120 cfm of compressed air atthe NFPA recommended 125 psi. Ship. wt. 7 lbs.BH1902 1 /2" CAFS Nozzle ComboCAFS - Force nozzle delivers both foam AND waterThe ONLY automatic nozzle combination specificallydesigned for Compressed Air Foam (CAFS) and waterapplicationsEngineered specifically for optimal foam streamperformance, as well as low pressure nozzleoperations for water use aloneBD155BD156CAFS-Force Nozzle CombinationCAFS-Force Tip1.800.323.0244 | www.edarley.com/foam155

CobraCompressed Air Foam Systems250 gpm NFPA rated engine drivenCAFS module.Simultaneous Flow (NFPA)250 gpm & 125 cfm @ 125 psiSimultaneous Flow260 gpm & 130 cfm @ 100 psiFOAMFeatures: 73HP Deutz BF4L2011 engine, air/oil cooled, direct injected, turbocharged,diesel fueled, 12 volt electric start, vernier throttle, Darley model 2 1/2AGE, 3 - independent 1 1 /2" CAF discharge mix points, 1 - 2 1 /2" water discharge,1 - 2 1 /2" tank to pump suction inlet, Rotary screw air compressor, Lightweightaluminum frame with latched doors, FoamPro Model 2001 system, Illuminated lasercut, brushed stainless steel control panel, with all engine, air compressor, waterpump and foam, injection system controls, gauges, and instruments installedPerformanceModel Water Air Compressor Outlet Dimensions Weight PriceCobra 250 gpm @ 150 psi 130 cfm @ 125 psi 2 1 /2" Length: 69" 2,100 lbs.175 gpm @200 psi Water Width: 34" (1,134 kg)125 gpm @ 250 psi Discharge Height: 65"MongooseSimultaneous Flow (NFPA)64 gpm & 32 cfm @ 125 psiFeatures: 28HP KawasakiSimultaneous Flowengine, air cooled, V-Twin, 100 gpm & 45 cfm @ 100 psigasoline powered, 12 VDCelectric start, Darley model 2BE with 1 fully adjustable 1 1 /2" CAF Discharge mixpoint, 2 1 /2" water discharge, 2 1 /2" Direct tank fill, 2 1 /2" NPT suction inlet, Air jetPrimer, 2 1 /2" Water and Air pressure gauges, pump drain valve, stainless steelplumbing, rotary screw compressor, manufacturer approved for flows of 40 cfm @150 psi, lightweight aluminum, Darley Fast Foam 50 Class "A" Foam proportioner,illuminated laser cut, Brushed Stainless Steel panel with infused powder coatpainted labels, Foam Injection System controls installedWater tankPoly skid frame and water/foam tankDischarge valveSuction valveSidesEconomy hose reelCAF hose reelFuel tankPerformanceModel Water Air Compressor Inlet Outlet Dimensions Weight PriceMongoose 160 gpm @ 100 psi 50 cfm @ 125 psi 2 1 /2" 2 1 /2" Length: 36"+6" air flow 800 lbs.NPT NST Width: 47 1 /4"Height: 29 5 /8"Lethal WeaponSimultaneous Flow (NFPA)This NFPA 1901 rated cross mount module250 gpm & 125 cfm @ 125 psiis time tested with a history nearing 20years. It has four discharges standard and it features a full roll-up door over theoperator’s panel.Features: 73HP Deutz BF4L2011F direct injected, turbo-charged, diesel fueled, 12-voltelectric start with oil pressure gauge, voltmeter, tachometer/hourmeter, vernierthrottle, Darley model 2 1/2 AGE, 4 - 2" CAF discharge mix point, 3" tank-to-pumpsuction inlet, pressure relief valve, 2 1 /2" gated suction valve - optional, 2 1 /2" NH femaleswivel direct tank fill inlet with 2 1 /2" valve, Master drain, Stainless steel plumbing,Mini pumper, Wildland/Quick attack vehicle, Rotary screw air compressor withAutoOdin balance valve, Lightweight aluminum frame, FoamPro Model 2001 systemPerformanceModel Water Air Compressor Inlet Outlet Dimensions Weight PriceLethal 250 gpm @ 150 psi 130 cfm @ 125 psi 2 1 /2" 2 1 /2" Length: 80" 2,500 lbs.Weapon 175 gpm @ 200 psi Width: 40" (1,134 kg)125 gpm @ 250 psi Height: 48"1561.800.323.0244 | www.edarley.com/foam

ColtMini pumperRescuesWildland/InterfaceCompressed Air Foam SystemsFeatures: 29HP Kawasaki engine, liquid cooled, V-twin, gasolinepowered, fuel injected, vernier throttle, 12-volt electric start, Darleymodel 1 1/2 AE pump, 1 - fully adjustable 1 1 /2" CAF discharge mixpoint, 1 1 /2" water discharge, 2" NPT suction inlet, 2 1 /2" water and airpressure gauges, stainless steel plumbing, 12-volt primer.Options: Diesel driven version available (Mustang). Call for details.PerformanceModel Water Air Compressor Inlet Outlet Dimensions Weight PriceColt 135 gpm @ 100 psi 50 cfm @ 125 psi 2 1 /2" NH 1 1 /2" Water Length: 38" 850 lbs.Discharge Width: 48" (386 kg)Height: 32"DerringerSimultaneous Flow (NFPA)100 gpm & 50 cfm @ 125 psiFOAMMini PumperRescuesWildland/InterfaceSimultaneous Flow130 gpm & 60 cfm @ 100 psiFeatures: 34 HP Briggs & Stratton Vanguard engine, diesel, liquidcooled, 3 cylinder, 12-volt electric start, turbo charged, Darley model1 1/2 AGE pump, 2 - independent 1 1 /2" CAF discharge mix points,1 - 2" tank to pump suction inlet, 1 - direct tank fill with 2 1 /2" femaleswivel, 12-volt electric primer system.PerformanceModel Water Air Compressor Dimensions Weight PriceDerringer 160 gpm @ 100 psi 60 cfm @ 125 psi Length: 48" 1,330 lbs. (603 kg)Width: 48" Ship. wt. forHeight: 37" base unit onlyKodiak250 gpm, NFPA 1901 ratedrear mounted CAFS moduleMini pumperWildland/Quick attack vehicleOptional roll-up doors*note dimension changeFeatures: 81 HP Detroit diesel engine,liquid cooled, 4 cylinder, turbo-charged, diesel fueled, 12-volt electricstart with oil pressure gauge, voltmeter, tachometer/hourmeter, vernierthrottle, Darley model 2 1/2 AGE pump, 3 - independent 1 1 /2" CAFdischarge mix points, 1 - 2 1 /2" water discharge, 1 - 2 1 /2" tank-to-pumpsuction inlet, master drain valve, Pro-S governor, direct tank fill, 12-voltrotary primer.Simultaneous Flow (NFPA)250 gpm & 125 cfm @ 125 psiPerformanceModel Water Air Compressor Inlet Outlet Dimensions Weight PriceKodiak 250 gpm @ 150 psi 130 cfm @ 125 psi 1-2 1 /2" 1-2 1 /2" Length: 59 1 /2" 1,880 lbs.175 gpm @ 200 psi Width: 47 1 /2" (853 kg)125 gpm @ 250 psi Height: 46"1.800.323.0244 | www.edarley.com/foam157

LDMBC PumpAutoCAFS -Air PressureBalancing ValveAir DistributionManifoldAvailable as acomplete moduleFOAMElectric “Hot Shift” ClutchAir Compressor Intake ValveVertical Mounted (Shown)Horizontal Mounted (Optional)Compact oil reservoir withbuilt-in oil separatorLDMBCFront ViewAPPLICATIONSAerialPumperRescue pumperPumper tankerSTANDARD EQUIPMENT4-2 1 /2" NH, 1 /4 turn-ball valves2-5 or 6" NH suction adapters and caps, dischargeand suction companion flanges as needed1610 or 1710 full round yokes standardOutput shaft for AZ01803 220 cfm compressor packageRemote packing adjustment cablesFeatures: 1000-1750 gpm, single stage, centrifugal,midship mounted pump forward.Optional Equipment: Foam manifold, air distributionmanifolds, CAFS valve packages, FoamPro system can bepre-installed and tested.AutoCAFS ®AutoCAFS--- Commander control system. Indicates and operatesall CAFS functions and system information.PerformanceModel Simultaneous Water Simultaneous Compressed Air Dimensions WeightLDMBC 1250 gpm @ 125 psi 220 cfm @ 125 psi Length: 40" 2,200 lbs. (997 kg)Width: 76"Height: 46"1581.800.323.0244 | www.edarley.com/foam