fujifilm sericol uvibond uv matt varnish uv400 - FUJIFILM Australia

products.fujifilm.com.au

fujifilm sericol uvibond uv matt varnish uv400 - FUJIFILM Australia

FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONPRODUCT NAMEFujifilm Sericol Uvibond UV Matt Varnish UV400SYNONYMS"screen printing lacquer"PROPER SHIPPING NAMEENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(contains tripropylene glycol diacrylate)PRODUCT USEScreen printing lacquer.SUPPLIERCompany: FUJIFILM Australia Pty LtdAddress:114 Old Pittwater RoadBrookvaleNSW, 2100AUSTelephone: +61 2 9466 2600Emergency Tel: +61 1800 039 008Emergency Tel: +61 3 9573 3112Fax: +61 2 9938 1975Section 2 - HAZARDS IDENTIFICATIONSTATEMENT OF HAZARDOUS NATUREHAZARDOUS SUBSTANCE. DANGEROUS GOODS. According to NOHSC Criteria, and ADG Code.HAZARD RATINGSFlammability: 0Toxicity: 0MinMaxBody Contact: 2Reactivity: 2Chronic: 2POISONS SCHEDULENoneRISK■ Irritating to eyes respiratory system and skin.■ May cause SENSITISATION by skin contact.■ Toxic to aquatic organisms may cause long-term adverseeffects in the aquatic environment.■ Cumulative effects may result following exposure*.Min/Nil=0Low=1Moderate=2High=3Extreme=4SAFETY■ Do not breathe gas/ fumes/ vapour/ spray.■ Avoid contact with skin.■ Wear eye/ face protection.■ To clean the floor and all objects contaminated by this material usewater and detergent.Page 1 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1■ Possible respiratory sensitiser*.* (limited evidence).■ This material and its container must be disposed of in a safe way.■ In case of contact with eyes rinse with plenty of water and contactDoctor or Poisons Information Centre.■ If swallowed IMMEDIATELY contact Doctor or Poisons InformationCentre (show this container or label).■ Use appropriate container to avoid environment contamination.■ Avoid release to the environment. Refer to special instructions/safety data sheets.■ This material and its container must be disposed of as hazardouswaste.Section 3 - COMPOSITION / INFORMATION ON INGREDIENTSNAME CAS RN %tripropylene glycol diacrylate 42978-66-5 25-50N-vinylcaprolactam 2235-00-9 10-25diphenyl(2,4,6-trimethylbenzoyl)phosphine 75980-60-8


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1 DO NOT use emetics. Where ingestion is suspected rinse mouth and give up to 200 ml water (5 ml/kg recommended) for dilutionwhere patient is able to swallow, has a strong gag reflex and does not drool.--------------------------------------------------------------ADVANCED TREATMENT-------------------------------------------------------------- Consider orotracheal or nasotracheal intubation for airway control in unconscious patient or where respiratory arrest has occurred. Positive-pressure ventilation using a bag-valve mask might be of use. Monitor and treat, where necessary, for arrhythmias. Start an IV D5W TKO. If signs of hypovolaemia are present use lactated Ringers solution. Fluid overload might create complications. Drug therapy should be considered for pulmonary oedema. Hypotension with signs of hypovolaemia requires the cautious administration of fluids. Fluid overload might create complications. Treat seizures with diazepam. Proparacaine hydrochloride should be used to assist eye irrigation.BRONSTEIN, A.C. and CURRANCE, P.L.EMERGENCY CARE FOR HAZARDOUS MATERIALS EXPOSURE: 2nd Ed. 1994.Section 5 - FIRE FIGHTING MEASURESEXTINGUISHING MEDIA■ Foam. Dry chemical powder. BCF (where regulations permit). Carbon dioxide. Water spray or fog - Large fires only.FIRE FIGHTING■ Alert Fire Brigade and tell them location and nature of hazard. May be violently or explosively reactive. Wear full body protective clothing with breathing apparatus. Prevent, by any means available, spillage from entering drains or water course. Fight fire from a safe distance, with adequate cover. If safe, switch off electrical equipment until vapour fire hazard removed. Use water delivered as a fine spray to control the fire and cool adjacent area. Avoid spraying water onto liquid pools. Do not approach containers suspected to be hot. Cool fire exposed containers with water spray from a protected location. If safe to do so, remove containers from path of fire.FIRE/EXPLOSION HAZARD■ Non combustible. Not considered a significant fire risk, however containers may burn.Decomposition may produce toxic fumes of: carbon dioxide (CO2), nitrogen oxides (NOx), other pyrolysis products typical of burningorganic material.May emit clouds of acrid smoke.FIRE INCOMPATIBILITY■ Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may resultHAZCHEM●3ZPersonal Protective EquipmentGas tight chemical resistant suit.EMERGENCY PROCEDURESMINOR SPILLS■ Environmental hazard - contain spillage. Clean up all spills immediately.Section 6 - ACCIDENTAL RELEASE MEASURESPage 3 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1 Avoid breathing vapours and contact with skin and eyes. Control personal contact by using protective equipment. Contain and absorb spill with sand, earth, inert material or vermiculite. Wipe up. Place in a suitable, labelled container for waste disposal.MAJOR SPILLS■ Environmental hazard - contain spillage. DO NOT touch the spill materialMinor hazard. Clear area of personnel. Alert Fire Brigade and tell them location and nature of hazard. Control personal contact by using protective equipment as required. Prevent spillage from entering drains or water ways. Contain spill with sand, earth or vermiculite. Collect recoverable product into labelled containers for recycling. Absorb remaining product with sand, earth or vermiculite and place in appropriate containers for disposal. Wash area and prevent runoff into drains or waterways. If contamination of drains or waterways occurs, advise emergency services.Personal Protective Equipment advice is contained in Section 8 of the MSDS.Section 7 - HANDLING AND STORAGEPROCEDURE FOR HANDLING■ Most acrylic monomers have low viscosity therefore pouring, material transfer and processing of these materials do not necessitateheating. Viscous monomers may require heating to facilitate handling. To facilitate product transfer from original containers, product must beheated to no more than 60 deg. C. (140 F.), for not more than 24 hours. Do NOT use localised heat sources such as band heaters to heat/ melt product. Do NOT use steam. Hot boxes or hot rooms are recommended for heating/ melting material. The hot box or hot room should be set a maximumtemperature of 60 deg. C. (140 F.). Do NOT overheat - this may compromise product quality and /or result in an uncontrolled hazardous polymerisation. If product freezes, heat as indicated above and mix gently to redistribute the inhibitor. Product should be consumed in its entiretyafter heating/ melting; avoid multiple "reheats" which may affect product quality or result in product degradation. Product should be packaged with inhibitor(s). Unless inhibited, product may polymerise, raising temperature and pressure, possiblyrupturing container. Check inhibitor level periodically, adding to bulk material if needed. In addition, the product's inhibitor(s) requirethe presence of dissolved oxygen. Maintain, at a minimum, the original headspace in the product container and do NOT blanket ormix with oxygen-free gas as it renders the inhibitor ineffective. Ensure air space (oxygen) is present during product heating / melting. Store product indoors at temperatures greater than the product's freeing point (or greater than 0 deg. C. (32 F).) if no freezing pointavailable and below 38 deg. C (100 F.). Avoid prolonged storage (longer than shelf-life) storage temperatures above 38 deg. C (100 F.). Store in tightly closed containers in a properly vented storage area away from heat, sparks, open flame, strong oxidisers, radiationand other initiators. Prevent contamination by foreign materials. Prevent moisture contact. Use only non-sparking tools and limit storage time. Unless specified elsewhere, shelf-life is 6 months from receipt. DO NOT allow clothing wet with material to stay in contact with skin Avoid all personal contact, including inhalation. Wear protective clothing when risk of exposure occurs. Use in a well-ventilated area. Avoid contact with moisture. Avoid contact with incompatible materials. When handling, DO NOT eat, drink or smoke. Keep containers securely sealed when not in use. Avoid physical damage to containers. Always wash hands with soap and water after handling. Work clothes should be laundered separately. Launder contaminated clothing before re-use. Use good occupational work practice. Observe manufacturer's storing and handling recommendations. Atmosphere should be regularly checked against established exposure standards to ensure safe working conditions are maintained.Page 4 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1SUITABLE CONTAINER■ Polyethylene or polypropylene container. Packing as recommended by manufacturer. Check all containers are clearly labelled and free from leaks.STORAGE INCOMPATIBILITY■ for multifunctional acrylates: Avoid exposure to free radical initiators (peroxides, persulfates) , iron, rust, oxidisers, and strong acids and strong bases. Avoid heat, flame, sunlight, X-rays or ultra-violet radiation. Storage beyond expiration date, may initiate polymerisation. Polymerisation of large quantities may be violent (even explosive)STORAGE REQUIREMENTS■ Polymerisation may occur slowly at room temperature. Storage requires stabilising inhibitor content and dissolved oxygen content to be monitored. Refer to manufacturer's recommendedlevels. DO NOT overfill containers so as to maintain free head space above product. Blanketing or sparging with nitrogen or oxygen free gas will deactivate stabiliser.Rotate all stock to prevent ageing. Use on FIFO (First In-First Out) basis. Store below 38 deg. C. Store in original containers. Keep containers securely sealed. Store in a cool, dry, well-ventilated area. Store away from incompatible materials and foodstuff containers. Protect containers against physical damage and check regularly for leaks. Observe manufacturer's storing and handling recommendations.EXPOSURE CONTROLSSection 8 - EXPOSURE CONTROLS / PERSONAL PROTECTIONThe following materials had no OELs on our records• tripropylene glycol diacrylate:CAS:42978-66-5 CAS:68901-05-3• N-vinylcaprolactam:CAS:2235-00-9• diphenyl(2,4,6-trimethylbenzoyl)phosphine: CAS:75980-60-8 CAS:596818-40-5PERSONAL PROTECTIONRESPIRATORType A Filter of sufficient capacityEYE■ Safety glasses with side shields. Chemical goggles. Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document,describing the wearing of lens or restrictions on use, should be created for each workplace or task. This should include a review oflens absorption and adsorption for the class of chemicals in use and an account of injury experience. Medical and first-aid personnelshould be trained in their removal and suitable equipment should be readily available. In the event of chemical exposure, begin eyeirrigation immediately and remove contact lens as soon as practicable. Lens should be removed at the first signs of eye redness orirritation - lens should be removed in a clean environment only after workers have washed hands thoroughly. [CDC NIOSH CurrentIntelligence Bulletin 59]HANDS/FEET■ NOTE: The material may produce skin sensitisation in predisposed individuals. Care must be taken, when removing gloves and otherPage 5 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1protective equipment, to avoid all possible skin contact. Contaminated leather items, such as shoes, belts and watch-bands should be removed and destroyed.Suitability and durability of glove type is dependent on usage. Factors such as: frequency and duration of contact, chemical resistance of glove material, glove thickness and dexterity,are important in the selection of gloves.General warning: Do NOT use latex gloves! Use only recommended gloves - using the wrong gloves may increase the risk:Use of thin nitrile rubber gloves: Nitrile rubber (0.1 mm) ExcellentExposure condition Short time use; (few minutes less than 0.5tactibility ("feel"), powder-free Disposable Inexpensive Givehour) Little physical stressadequate protection to low molecular weigh acrylic monomersExposure condition Medium time use; less than 4 hours Physicalstress (opening drums, using tools, etc.)Use of medium thick nitrile rubber gloves Nitrile rubber, NRL (latex)free; 0.56 mm low tactibility ("feel"),powder free High price Gives adequate protection for mostacrylates in combination with commonly used solvents up to 8Exposure condition Long time Cleaning operationshours Do NOT give adequate protection to low molecular weightmonomers at exposures longer than 1 hour Avoid use of ketonesand acetates in wash-up solutions.Where none of this gloves ensure safe handling (for example in long term handling of acrylates containing high levels of acetates and/ orketones, use laminated multilayer gloves.Guide to the Classification and Labelling of UV/EB Acrylates Third edition, 231 October 2007 - Cefic.OTHER■ Overalls. P.V.C. apron. Barrier cream. Skin cleansing cream. Eye wash unit.ENGINEERING CONTROLS■ Local exhaust ventilation usually required. If risk of overexposure exists, wear approved respirator. Correct fit is essential to obtainadequate protection. Supplied-air type respirator may be required in special circumstances. Correct fit is essential to ensure adequateprotection.An approved self contained breathing apparatus (SCBA) may be required in some situations.Provide adequate ventilation in warehouse or closed storage area.Section 9 - PHYSICAL AND CHEMICAL PROPERTIESAPPEARANCEColoured liquid with a characteristic odour; does not mix with water.PHYSICAL PROPERTIESLiquid.Does not mix with water.Sinks in water.StateMeltingRange(°C)BoilingRange(°C)FlashPoint(°C)LiquidNotAvailable109NotApplicableMolecularWeightViscositySolubilityinwater(g/L)pH(1%solution)NotApplicableNotAvailableImmiscibleNotApplicablePage 6 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1DecompositionTemp(°C)NotAvailablepH (assupplied)NotApplicableAutoignitionTemp(°C)NotApplicableVapourPressure(kPa)NotAvailableUpperExplosiveLimit(%)NotApplicableSpecificGravity(water=1)1.42LowerExplosiveLimit(%)NotApplicableRelativeVapourDensity(air=1)NotAvailableVolatileComponent(%vol)NotAvailableEvaporationRateNotAvailableSection 10 - CHEMICAL STABILITYCONDITIONS CONTRIBUTING TO INSTABILITY■ Polymerisation may occur at elevated temperatures. Polymerisation may be accompanied by generation of heat as exotherm. Process is self accelerating as heating causes more rapid polymerisation. Exotherm may cause boiling with generation of acrid, toxic and flammable vapour. Polymerisation and exotherm may be violent if contamination with strong acids, amines or catalysts occurs. Polymerisation and exotherm of material in bulk may be uncontrollable and result in rupture of storage tanks. Polymerisation may occur if stabilising inhibitor becomes depleted by aging. Stabilising inhibitor requires dissolved oxygen to be present in liquid for effective action. Specific storage requirements must be met for stability on ageing and transport.For incompatible materials - refer to Section 7 - Handling and Storage.POTENTIAL HEALTH EFFECTSSection 11 - TOXICOLOGICAL INFORMATIONACUTE HEALTH EFFECTS■ Irritating to eyes, respiratory system and skin.CHRONIC HEALTH EFFECTS■ May cause SENSITISATION by skin contact.■ Possible respiratory sensitiser*.■ Cumulative effects may result following exposure*.■ * (limited evidence).TOXICITY AND IRRITATION■ Contact allergies quickly manifest themselves as contact eczema, more rarely as urticaria or Quincke's oedema. The pathogenesis ofcontact eczema involves a cell-mediated (T lymphocytes) immune reaction of the delayed type. Other allergic skin reactions, e.g. contacturticaria, involve antibody-mediated immune reactions. The significance of the contact allergen is not simply determined by itssensitisation potential: the distribution of the substance and the opportunities for contact with it are equally important. A weaklysensitising substance which is widely distributed can be a more important allergen than one with stronger sensitising potential with whichfew individuals come into contact. From a clinical point of view, substances are noteworthy if they produce an allergic test reaction inmore than 1% of the persons tested.Asthma-like symptoms may continue for months or even years after exposure to the material ceases. This may be due to a nonallergeniccondition known as reactive airways dysfunction syndrome (RADS) which can occur following exposure to high levels of highlyirritating compound. Key criteria for the diagnosis of RADS include the absence of preceding respiratory disease, in a non-atopicindividual, with abrupt onset of persistent asthma-like symptoms within minutes to hours of a documented exposure to the irritant. Areversible airflow pattern, on spirometry, with the presence of moderate to severe bronchial hyperreactivity on methacholine challengetesting and the lack of minimal lymphocytic inflammation, without eosinophilia, have also been included in the criteria for diagnosis ofRADS. RADS (or asthma) following an irritating inhalation is an infrequent disorder with rates related to the concentration of and durationof exposure to the irritating substance. Industrial bronchitis, on the other hand, is a disorder that occurs as result of exposure due to highPage 7 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1concentrations of irritating substance (often particulate in nature) and is completely reversible after exposure ceases. The disorder ischaracterised by dyspnea, cough and mucus production.UV/EB acrylates are divided into two groups; "stenomeric" and "eurymeric" acrylates. The first group consists of well-defined acrylateswhich can be described by a simple idealised chemical;they are low molecular weight species with a very narrow weight distributionprofile. The eurymeric acrylates cannot be described by an idealised structure and may differ fundamentally between various suppliers;they are of relatively high molecular weigh and possess a wide weight distribution.Stenomeric acrylates are usually more hazardous than the eurymeric substances. Stenomeric acrylates are also well defined whichallows comparison and exchange of toxicity data - this allows more accurate classification.The stenomerics cannot be classified as a group; they exhibit substantial variation.The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritantsmay produce conjunctivitis.The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, theproduction of vesicles, scaling and thickening of the skin.Where no "official" classification for acrylates and methacrylates exists, there has been cautious attempts to create classifications in theabsence of contrary evidence. For exampleMonalkyl or monoarylesters of acrylic acids should be classified as R36/37/38 and R51/53Monoalkyl or monoaryl esters of methacrylic acid should be classified as R36/37/38.Section 12 - ECOLOGICAL INFORMATIONToxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.This material and its container must be disposed of as hazardous waste.Avoid release to the environment.Refer to special instructions/ safety data sheets.EcotoxicityIngredienttripropyleneglycoldiacrylateN-vinylcaprolactamdiphenyl(2,4,6-trimethylbenzoyl)phosphinePersistence:Water/SoilPersistence:AirBioaccumulationMobilityHIGH LOW HIGHLOW LOW HIGHHIGH LOW LOWSection 13 - DISPOSAL CONSIDERATIONS■ Containers may still present a chemical hazard/ danger when empty. Return to supplier for reuse/ recycling if possible.Otherwise: If container can not be cleaned sufficiently well to ensure that residuals do not remain or if the container cannot be used to store thesame product, then puncture containers, to prevent re-use, and bury at an authorised landfill. Where possible retain label warnings and MSDS and observe all notices pertaining to the product.Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws operatingin their area. In some areas, certain wastes must be tracked.A Hierarchy of Controls seems to be common - the user should investigate: Reduction, Reuse Recycling Disposal (if all else fails)This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. If it has beencontaminated, it may be possible to reclaim the product by filtration, distillation or some other means. Shelf life considerations shouldalso be applied in making decisions of this type. Note that properties of a material may change in use, and recycling or reuse may notalways be appropriate. DO NOT allow wash water from cleaning or process equipment to enter drains. It may be necessary to collect all wash water for treatment before disposal. In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first. Where in doubt contact the responsible authority. Recycle wherever possible or consult manufacturer for recycling options. Consult State Land Waste Authority for disposal.Page 8 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1Bury or incinerate residue at an approved site.Recycle containers if possible, or dispose of in an authorised landfill.Section 14 - TRANSPORTATION INFORMATION■ Environmentally Hazardous Substances meeting the descriptions of UN 3077 or UN 3082 are not subject to this Code whentransported by road or rail in;(a) packagings;(b) IBCs; or(c) any other receptacle not exceeding 500 kg(L).- Australian Special Provisions (SP AU01) - ADG Code 7th Ed.Labels Required: MISCELLANEOUSHAZCHEM:●3Z (ADG7)Land Transport UNDG:Class or division: 9 Subsidiary risk: NoneUN No.: 3082 UN packing group: IIIShipping Name:ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(contains tripropylene glycol diacrylate)Air Transport IATA:ICAO/IATA Class: 9 ICAO/IATA Subrisk: ̶UN/ID Number: 3082 Packing Group: IIISpecial provisions:Cargo OnlyA97Packing Instructions: 914 Maximum Qty/Pack: 450 LPassenger and CargoPassenger and CargoPacking Instructions: 914 Maximum Qty/Pack: 450 LPassenger and Cargo LimitedQuantityPassenger and Cargo LimitedQuantityPacking Instructions: Y914 Maximum Qty/Pack: 30 kg GShipping Name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,N.O.S. *(CONTAINS TRIPROPYLENE GLYCOL DIACRYLATE)Maritime Transport IMDG:IMDG Class: 9 IMDG Subrisk: NoneUN Number: 3082 Packing Group: IIIEMS Number: F-A,S-F Special provisions: 274 909 944Limited Quantities: 5 L Marine Pollutant: Not DeterminedShipping Name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,N.O.S.(contains tripropylene glycol diacrylate)POISONS SCHEDULENoneSection 15 - REGULATORY INFORMATIONREGULATIONSRegulations for ingredientstripropylene glycol diacrylate (CAS: 42978-66-5,68901-05-3) is found on the following regulatory lists;Page 9 of 10


FUJIFILM SERICOL UVIBONDUV MATT VARNISH UV400Hazard Alert Code:MODERATEChemwatch Material Safety Data Sheet Revision No: 6 Chemwatch 4600-29Issue Date: 13-Jan-2010 CD 2010/1"Australia Hazardous Substances","Australia Inventory of Chemical Substances (AICS)","International Council of Chemical Associations(ICCA) - High Production Volume List","OECD Representative List of High Production Volume (HPV) Chemicals"N-vinylcaprolactam (CAS: 2235-00-9) is found on the following regulatory lists;"Australia Inventory of Chemical Substances (AICS)","OECD Representative List of High Production Volume (HPV) Chemicals"diphenyl(2,4,6-trimethylbenzoyl)phosphine (CAS: 75980-60-8,596818-40-5) is found on the followingregulatory lists;"Australia Inventory of Chemical Substances (AICS)"No data for Fujifilm Sericol Uvibond UV Matt Varnish UV400 (CW: 4600-29)Section 16 - OTHER INFORMATIONDenmark Advisory list for selfclassification of dangerous substancesSubstance CAS Suggested codes tripropylene glycol diacrylate 68901- 05- Xn Carc3; R40 N 3 R50 N- vinylcaprolactam 2235- 00- XnRepr3; R63 9Ingredients with multiple CAS NosIngredient NameCAStripropylene glycol diacrylate 42978-66-5, 68901-05-3diphenyl(2,4,6-trimethylbenzoyl)phosphine 75980-60-8, 596818-40-5■ Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independentreview by the Chemwatch Classification committee using available literature references.A list of reference resources used to assist the committee may be found at:www.chemwatch.net/references.■ The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whetherthe reported Hazards are Risks in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scaleof use, frequency of use and current or available engineering controls must be considered.This document is copyright. Apart from any fair dealing for the purposes of private study, research, review orcriticism, as permitted under the Copyright Act, no part may be reproduced by any process without writtenpermission from CHEMWATCH. TEL (+61 3) 9572 4700.Issue Date: 13-Jan-2010Print Date:26-Mar-2010Page 10 of 10

More magazines by this user
Similar magazines