Solar-Log™ Hardware - Krannich Solar

Solar-Log™ Hardware - Krannich Solar

Solar-Log HardwareSolar-Log 500 is a convincing choice due to its high performanceSuitable for connection:Display:Optionally available with:The Solar-Log 500 is operated either via the 2-line text display or via a PC with a popular web browser. The installation of software is notrequired. The graphic and tabular evaluations can be accessed at any time locally or via the Internet.Suitable for plants with up to ten inverters and optionalPowermanagement and cos φ controlRecommended: max. plant size 50 kWp / Solar-Log 500Possible to monitor consumption of self-produced powerNotification via SMS and emailOptional: wireless connection via WiFi and BluetoothSimple installation and connection• Solar-Log Easy InstallationThe installation and initial operation of the data logger is quickand simple with “Easy Installation”. The search for inverters andInternet log-on takes places immediately and automatically.• Cable coverWith its attractive design the cable cover for the Solar-Log offers the best possible mechanical protection for interfacesand cables.Solar-Log WEBThe Solar-Log WEB online portal expands the monitoring functionof the Solar-Log and offers comprehensive evaluationprograms concerning the monitoring of PV plants.• Solar-Log WEB “Commercial Edition”Solar-Log WEB “Commercial Edition” allows the plant operatorto offer an expanded and professional plant monitoringservice in the framework of a “Full Service” maintenanceagreement.Number of inverters Sensors Meter S 0 Large display Ripple control receiver

Solar-Log added functions• Solar-Log PM+The new EEG 2012 (Germany) places special demands on newand existing plants: PV plants must engage in feed-in managementand network safety management in order to preventan overload of the distribution network. The PM+ product linecovers the entire spectrum of requirements with regard toactive and reactive power.• Solar-Log consumption of self-produced energyThe Solar-Log 500 makes it possible to measure the consumptionof your own self-produced energy and to display thisin graphic and tabular formats via the Solar-Log WEB. Inorder to consume the power that you have produced yourself,a digital meter reader is required. As a consumption meter, itis used to measure the power consumed and to display this incomparison to the power produced.Data securityCordless connection to the internetor to SMA inverters• Solar-Log 500 WiFiSolar-Log WiFi allows you to use the WiFi radio data networkthat is often available in homes and offices. The antenna thatis integrated within the device is able to receive nearby WiFinetworks. If the signal is weak, WiFi repeaters may be necessary.• Solar-Log 500 BTThis data logger is equipped with a Bluetooth module andallows wireless connection to all SMA BT inverters.Representative presentation• Solarfox large displayIn connection with the Solar-Log , the large display can presentthe live data of a PV plant in a way that is visually appealingand in combination with individual advertising.• The data volume from the Solar-Log can be recorded for upto 20 years. The micro SD card is used to protect against anyloss of data in the event of a power failure.

Product comparisonInverter communication / inverter = WR1)Depending on the inverter used, and the cable length. (details can also vary from one type of device to another)2)Other important information about Bluetooth and compatibility, Powermanagement, „own power“ consumption, SCB and SMBcentral inverters can be found on our website 200 Solar-Log 500 Solar-Log 1000PM+ (2) • • •PM+ / WiFi (2) • • •PM+ / GPRS (2) • – •Bluetooth (BT) (2) • • •WiFi (wireless LAN) (2) • • •Bluetooth (BT) / WiFi (2) • • •GPRS (2) • – •Central inverter SCB and SMB 2) – – •max. number of inverters 1 up to 10 up to 100Communication interface 1 x RS485 / RS422 1 x RS485 / RS4221 x RS485,1 x RS485 / RS422 / 1 x CANrecommended max. plant size 15 kWp 50 kWp 1 MWpmax. cable length max. 1000 m 1) max. 1000 m 1) max. 1000 m 1)Plant monitoringString monitoring (depending on type of inverter) • • •Inverter failure, status of fault and power monitoring • • •Connection of sensors (temp. / wind) • • •E-mail and SMS alarm • • •Local alarm (pot.-free contact) – – •Yield forecast and degradation calculation • • •EEG “own power consumption”: Digital current meters • • •EEG “own power consumption”: Control of ext. consumers – – •VisualisationIntegrated web servers • • •Graphic visualisation – PC local and internet • • •Graphic visualisation – USB flash drive – – •LED – status display • • •Display on device – 2-line text display full-graphic displayOperation on device – keypad entry via touch screenLarge display RS485 / S 0 impulse – • •InterfacesEthernet network • • •USB flash drive – – •Modem, analogue / GPRS(GSM) / DSL – – •Potential-free contact (relay) – – •Alarm contact (anti-theft) – – •General dataNetwork voltage / device voltage / current consumption115 V – 230 V / 12 V / 3 WAmbient temperature -10 °C bis +50 °CHousing / dimensions (W x D x H) in cm // Assembly / Protection levelPlastic / 22,5 x 4 x 28,5 / Wall-mounted / IP 20 (only for interior use)Connection to Solar-Log WEB • • •Multi-lingual (DE, EN, ES, FR, IT, NL, DK) • • •Memory, Micro-SD, 2 GB,Endless-loop data recordingWarranty cover age• • •5 years

In DetailAccessoriesAccessories forSMA invertersSolar-Log 200 Solar-Log 500 Solar-Log 1000Fully packaged cable kits for most supported invertersDigital Meter Digital Meter Digital MeterPowerLine Package PowerLine Package PowerLine PackageRS485 Wireless Package RS485 Wireless Package RS485 Wireless PackageSensors Sensors Sensors– – Mobile Wireless Package– – Modem PackageOvervoltage protection Overvoltage protection Overvoltage protectionSpecial PiggyBack RS485 (except TL-20 series) (page 39)Data Module SMA RS485 (page 39)Top Features Solar-Log 200 Solar-Log 500 Solar-Log 1000CompatibilitySoftwareEasy InstallationCompatible with all the major inverter manufacturers, can be found on our website, no software installation is required.Connection is usually possible without PC and installation expertise.The inverter search and the internetregistration is enabled immediatelyand is started automatically.Query for additional information,then automatic inverter search and internet registration.Network recognitionAbility to be reachedon the local networkAutomatic search for the DHCP server and assignmentof a valid IP address in the local network.WINS registration automatically takes place and the Solar-Log can be foundin a web browser at: http://solar-log.The IP address of the Solar-Log no longer needs to be known,unless there are several Solar-Logs on the network.Additional functionMonitoring and optimisationof own energy consumptionMonitoring and optimisationof own energy consumptionMonitoring and optimisationof own energy consumptionMonitoring of central invertersEvaluation of Sensor Box dataSupport for theSolar-Log SCBand Solar-Log SMBMonitoring of large systemswith the support of Solar-Log 1000or Solar-Log 1000 PM+ acc. to theGerman law § 6.1 EEG 2009with reduction in active powerabove 100 kWpSolar-Log 1000 PM+ standby powerregulation above 100 kWp (legallystipulated in Germany since 1 July 2010)Article number overview for all Solar-LogsType Art.-No. Solar-Log 200 Art.-No. Solar-Log 500 Art.-No. Solar-Log 1000Standard 255240 210501 211001BT 255241 210502 211002WiFi 255191 255189 255185BT / WiFi 255192 255190 255186PM+ 255362 255364 211005PM+ / WiFi 255363 255365 255366GPRS 255349 – 255187PM+ / GPRS 255402 – 255188

More magazines by this user
Similar magazines